SAMPE Long Beach Below, you will find a listing of Technical Paper presentations planned for SAMPE Long Beach. Abstracts and speaker information for all Technical Papers listed below, as well as Panel, Featured Lecture, and Tutorial information is available online. This list of presenations is subject to change and cancellation due to circumstances beyond our control.

Tuesday Additive Manufacturing - 1 (Metal) Room: 104A Category Chairs: Teresa Clement, Raytheon Company; Jennifer Fielding, Air Force Research Laboratory; Richard Martukanitz, Penn State CIMP-3D; and R. Byron Pipes, Purdue University

8:00 AM On the Prediction and Engineering of Microstructures and Properties in Additively Manufactured Metallic Materials Peter Collins, Iowa State University

8:30 AM Thermomechanical Modeling and In Situ Experimental Validation of The Laser Powder-Bed Fusion Process Erik Denlinger, Pan Computing LLC

Adhesives, Bonding, and Bonded Joint Certification - 1 Room: 101A Category Chairs: Tony Belcher, Boeing Research & Technology; John Connell, NASA Langley Research Center; Rikard Heslehurst, M51 Advanced Composites Training and Resources, Inc; Michelle Palmer, Lockheed Martin Aeronautics; Kara Storage, Air Force Research Laboratory; Kelly Williams, Eaton Corporation; Patrick Zimmerman, 3M

8:00 AM Tolerance of Bond In Composite-Concrete Interface with Various Adhesives Subjected to High Temperatures Yail Kim, University of Colorado Denver

8:30 AM Controlled Contamination of Epoxy Composites with PDMS and Removal by Laser Ablation Frank Palmieri III., NASA

Advanced Manufacturing Methods -1 Room: 101B Category Chairs: Ehsan Barjasteh, California State University Long Beach; Axel Boettcher, Boettcher Consult; Timotei Centea, University of Southern California; Michael Maher, DARPA

8:00 AM Shock-Induced Reversible Phase Transformation from Rutile to Anatase in Tio2 Powders Jayaram Vishakantaiah PhDPhD, Indian Institue of Science (IISc), Bangalore, India

8:30 AM

Orifice Design for Extruding Paste-Like Adhesives and Other Thick Liquids Thomas Sutherland, Retired

Ceramic Matric Composites Room: 102B Category Chairs: Brian Flinn, University of Washington; Thomas Tsotsis. The Boeing Company

8:00 AM Awj Machnining Advances and Challenges for CMCS Mohamed Hashish, Flow International Corporation

8:30 AM Monazite Fiber Coating for Strength and Toughness Improvement of Geopolymer Matrix Composites Patrick Jackson, Colorado State University/US Air Force

Design Room: 103A Category Chairs: Sanjib Chowdhury, University of Delaware – Center for Composite Materials (UD-CCM); Ryan Jones, Raytheon; Douglas Kenik, AutoDesk; Jerome Tzeng, US Army Research Laboratory; Brent Volk, Air Force Research Laboratory;

8:00 AM Lightweight Structure Design for Composite Yacht with Optimum Fiber Mass Content Daekyun Oh PhD, Mokpo National Maritime University.

8:30 AM Efficient Reduced Order Modeling of Composite Beams Ben Names, SDA, Inc

Multi-Purpose Energy Applications Room: 102A Category Chairs: Madhur Atreya, L&T Technology Services, LLC

8:00 AM Ultrasonic Pre-Treatments of Wood Chips Used In a Conventional Pyrolysis and Their Effect on Bio-Oil Composition and Calorimetry Eric Loranger, Universite du Quebec a Trois-Rivieres

NDE, NDT/NDI Testing Methods and Tools - 1 Room: 102C Category Chairs: Dave Forsyth, Texas Research Institute Austin, Inc.; Gary Georgeson, The Boeing Company; Ajay Koshti, NASA Johnson Space Center; Hong Tat, The Boeing Company

8:00 AM Optical Metrology for Finite Element Measurements John Tyson II., Trilion Quality Systems

8:30 AM NDT of Composites and Advances in Manual Scanning Equipment John Regsiter, R-CON NDT Inc.

Oil, Gas, and Offshore Technology Room: 103C Category Chairs: Aliene Elkins, SABIC Innovative Plastics; Juan Erni, Exova

8:00 AM Composite Tubing Liners for Oil and Gas Production Cole Carpenter, Montana Tech C.A.M.P.

8:30 AM Manufacturing and Testing of Lightweight, All-Composite Tanks for Storage and Transportation of Adsorbed Natural Gas Ranji Vaidyanathan, Oklahoma State University

Tuesday Afternoon Adhesives, Bonding, and Bonded Joint Certification - 2 Room: 101A Category Chairs: Tony Belcher, Boeing Research & Technology; John Connell, NASA Langley Research Center; Rikard Heslehurst, M51 Advanced Composites Training and Resources, Inc; Michelle Palmer, Lockheed Martin Aeronautics; Kara Storage, Air Force Research Laboratory; Kelly Williams, Eaton Corporation; Patrick Zimmerman, 3M

1:30 PM Disbond-Stopping Concepts for Bonded Composite Joints Thomas Löbel, German Aerospace Center (DLR)

2:00 PM Effect of Surface Treatments on Interfacial Strength of Metal – Polymer Composite Bond Syeda Noor E. Sumaiya, University of Manitoba

2:30 PM Fracture Behavior on Adhesively Bonded Composite Joints with Undesirable Bonding Conditions: A Multiscale Approach Dwayne McDaniel PhDPhD,

3:00 PM Assessment of Fracture Properties of MENs Doped Multifunctional Adhesives Dwayne McDaniel PhDPhD,

3:30 PM Automated Surface Preparation of Organic Matrix Composites for Structural Adhesive Bonding Arshaluis Hogikyan, Aerospace Materials Processing

4:00 PM Advances in Surfacing Film & Lightning Strike Protection Ruairi O'Kane, Henkel Corporation

Advanced Manufacturing Methods - 2 Room: 101B Category Chairs: Ehsan Barjasteh, California State University Long Beach; Axel Boettcher, Boettcher Consult; Timotei Centea, University of Southern California; Michael Maher, DARPA

1:30 PM

The Printing Process Of 3D Printer for Continuous CFRTP Yoichiro Koga, Tokyo Institute of Technology

2:00 PM How to Unchain Pultrusion Klaus Jansen, Thomas Technik + Innovation

2:30 PM Shape Adjustment Process for Epoxy Composites During Post Cure Jochen Schmidt, German Aerospace Center

3:00 PM Manufacturing of Hybrid Profiles: Continuous Fiber Reinforced Thermoset Profiles with a Thermoplastic Top Layer Peter Schneider, Institute of Plastics Processing at RWTH Aachen University (IKV)

3:30 PM Analysis of The Integrated Production of Sandwich Parts Made of Pu Foam Core and Continuous Fiber-Reinforced Top Layers in a Combined Spray Impregnation and Wet Pressing Process Christos Karatzias, Institute of Plastics Processing at RWTH Aachen University (IKV)

4:00 PM Inductive Pre-Bonding of Stiffened Structural Components Made of CFRP Using The Example of Co- and Secondary Bonding Processes Hakan Ucan, German Aerospace Center

4:30 PM Development, Characterization, and Modeling of Multi-directionally Reinforced Polymer Matrix Composites for Structural Applications Steven Violette PhD, Fiber Materials Inc.

Design and Stress Analysis - 1 Room: 103A Category Chairs: Sanjib Chowdhury, University of Delaware – Center for Composite Materials (UD-CCM); Ryan Jones, Raytheon; Douglas Kenik, AutoDesk; Jerome Tzeng, US Army Research Laboratory; Brent Volk, Air Force Research Laboratory;

1:30 PM Bond Characteristics Between Steel Bridge Girders and Ultra High Modulus CFRP Laminates Abheetha Peiris, University of Kentucky

2:00 PM Strengthening Autoclaved Areated Concrete (AAC) Beams Using Basalt Fabrics with Inorganic Matrix Alaa Abd Ali, Rutgers University

2:30 PM Effect of Simulated ‘Bi-Directionally Symmetric In-Plane Fiber Waviness’ Defects on Composite Properties Predicted With Finite Element Analysis in Unidirectional Carbon Fibers Kushal Reddy, Wichita State University

3:00 PM Automatic Detection of Critical Regions For Modeling Damage in Composite Materials Michael Macri II., Benet Labs

3:30 PM Enhanced Design Methods for Pressure-Actuated Cellular Structures and Evaluation

Benjamin Gramüller, German Aerospace Center

4:00 PM Variance Predictions for Discontinuous Composites Nicholas Smith, Wichita State University

4:30 PM Development of A Fatigue Test Set-Up For A Submodel Extracted From A Sandwich Concept Bus Body Peter Geuting, Daimler AG

Modeling and Mechanical Properties Room: 102B Category Chairs: TBD

1:30 PM Efficient Simulation of Graded Honeycomb Composites Structures: Parameterized 3D Solutions With 2D Computational Complexity Brice Bognet, Ecole Centrale of Nantes

2:00 PM EffectS of Surface Treatment on the tensile and bonding Properties of Carbon Fibers Guijun Xian, Harbin Institute of Technology

2:30 PM Molecular Dynamics Characterization of Simultaneous Improvement in Strain and Modulus in Highly Crosslinked Networks John Misasi, Western Washington University

3:00 PM Fea Examination of Commonly Used Fiber Shape Functions in Plain Weave Fabric Justin Ferranto, University of Nevada, Reno

3:30 PM Apparent Hoop Tensile Strength of Basalt Fiber and Hybrid Fiber Reinforced Polymers Eduard Kessler, NuCellSys GmbH (100% subsidiary of Daimler AG)

4:00 PM In-Situ Microscopy for Displacement and Strain Measurements of Uhmwpe Single Fibers in Tension Vincent Wu, U.S. Army Research Laboratory

4:30 PM Analysis Tools for Composite Laminate Material Properties Prediction David Najera, ATA Engineering

NDE, NDT/NDI Testing Methods and Tools - 2 Room: 102C Category Chairs: Dave Forsyth, Texas Research Institute Austin, Inc.; Gary Georgeson, The Boeing Company; Ajay Koshti, NASA Johnson Space Center; Hong Tat, The Boeing Company

1:30 PM Non-Destructive Sensing and Perforamnce Characterization on Penetration of Chloride Ions Through Composite-Concrete Interface Yail Kim, University of Colorado Denver

2:00 PM Normalized Temperature Contrast Processing in Infrared Flash Thermography

Ajay Koshti, NASA Johnson Space Center

2:30 PM Eddy Current Methods for Assessment of Thermal Protection System Materials Andrew Washabaugh PhDPhD, JENTEK Sensors, Inc.

3:00 PM Nondestructive Testing and Evaluation of Conventional and Reused Carbon Fiber Epoxy Composites Using Ultrasonic and Stitched Micro-CT Bo Jin, M.C Gill Composites Center, USC

3:30 PM Description of Damage Mechanisms and Estimation of Remaining Property of Carbon Fiber Reinforced Composite Materials Prasun Majumdar, University of South Carolina

4:00 PM A Comparison of Emerging In-Situ Inspection Techniques for Validation of Composite Progressive Damage Analysis Methods Joseph Schaefer PhD, The Boeing Company Room: 102A

1:30 PM A Parametric Study of The Recyclability of Carbon Fiber Reinforced Polymers Yijia Ma, University of Southern California

2:00 PM Prediction of the Stiffness Of Reused Carbon Fiber/Epoxy Composite Oriented Strand Board Using Finite Element Methods Bo Jin, M.C Gill Composites Center, USC

2:30 PM Stiffness Predictions of Random Chip Composites By Combining Finite Element Calculations with Inclusion Based Models Atul Jain, University of Southern California

3:00 PM Recycling of Uncured Prepreg Waste Via Long Discontinuous Fibre Compression Moulding: A Study of Flow Phenomena Interaction Adam Smith, McGill University

Sustainability: Effective Recycling of Materials Room: 102A Category Chairs: Lessa Grunenfelder, University of Southern California; Pascal Hubert, McGill University; Atul Jain, University of Southern California 1:30 PM A Parametric Study of The Recyclability of Carbon Fiber Reinforced Polymers Yijia Ma, University of Southern California 2:00 PM Prediction of the Stiffness Of Reused Carbon Fiber/Epoxy Composite Oriented Strand Board Using Finite Element Methods Bo Jin, M.C Gill Composites Center, USC

2:30 PM Stiffness Predictions of Random Chip Composites By Combining Finite Element Calculations with Inclusion Based Models Atul Jain, University of Southern California 3:00 PM Recycling of Uncured Prepreg Waste Via Long Discontinuous Fibre Compression Moulding: A Study of Flow Phenomena Interaction Adam Smith, McGill University

Testing, Materials Characterization, and Qualification - 1 Room: 103C Category Chairs: Madhur Atreya, L&T Technology Services, LLC; Timothy Briggs, Sandia National Laboratories; Jeremy Jacobs, NASA Johnson Space Center; David Miller, Montana State University

1:30 PM Influence of the Stacking Sequence on the Mechanical Properties of Notched Composite Plates: Numerical Simulation Frank Abdi PhD, Alpha STAR Corporation

2:00 PM Developed Technologies for Damage Simulation in Ultrathin Composite Reinforcements and Novel Material with Outstanding Impact Performance Elena Alvarez, Oxeon AB

2:30 PM Advanced Method for Void Fraction Evaluation of Natural Fiber Composites Using Micro-Ct Technology Ali Amiri PhD, North Dakota State University

3:00 PM Detecting Damage Progression in GFRPS Through Use of Ultrasonic Impulses and Acoustic Emission for Structural Health Monitoring David Miller, Montana State University

3:30 PM Measurement of Football Helmet Elastomeric and Tpu Material Energy Absorption Degradation from High Humidity and Temperature Conditions Kenneth Saczalski, Environmental research and Safety Technologists, Inc.

4:00 PM A Unit Circle Failure Criterion of Composite Laminates Stephen Tsai, Stanford University

4:30 PM Through-Thickness Properties of Woven Composite Materials Under Tensile and Compressive Loading Conditions German Reyes PhDPhD, Univesity of Michigan-Dearborn

Automotive and Industrial Engineering

Room: 102A Category Chairs: TBD

4:00 PM A Novel CF/PMP Composite for Ultra-Lightening Application Wataru Nagatsuka, The University of Tokyo

4:30 PM Feasibility and Demonstration of an Additive Manufacturing for Automotive Components Hendrik Mainka, Volkswagen Group of America Inc.

Wednesday Additive Manufacturing - 2 (Polymers) Room: 102C Category Chairs: Teresa Clement, Raytheon Company; Jennifer Fielding, Air Force Research Laboratory; Richard Martukanitz, Penn State CIMP-3D; and R. Byron Pipes, Purdue University

8:00 AM Development of A Model to Predict Temperature History and Crystallization Behavior Of 3D-Printed Parts Made from Fiber-Reinforced Thermoplastic Polymers Bastian Brenken, Purdue University

8:30 AM Infrared Preheating to Enhance Interlayer Strength of Components Printed on The Big Area Additive Manufacturing (BAAM) System Vidya Kishore, University of Tennessee, Knoxville

9:00 AM Design and Fabrication of Multifunctional Aerodynamic Structures Using Additive Manufacturing Giovanni Nino, Quest Integrated LLC

Adhesives, Bonding, and Bonded Joint Certification - 3 Room: 101A Category Chairs: Tony Belcher, Boeing Research & Technology; John Connell, NASA Langley Research Center; Rikard Heslehurst, M51 Advanced Composites Training and Resources, Inc; Michelle Palmer, Lockheed Martin Aeronautics; Kara Storage, Air Force Research Laboratory; Kelly Williams, Eaton Corporation; Patrick Zimmerman, 3M

8:00 AM Laser Pretreatment Of Contaminated Surfaces for Fusion Bonding Processes Kristian Lippky, Technische Universitaet Braunschweig, Institute of Joining and Welding

8:30 AM Metal-To-Composite Structural Joining for Drivetrain Applications Peter Fritz PhD, Eaton

9:00 AM Preparation and Characterization of Novel Vinyl Ester Formulations Derived from Cardanol Emre Kinaci, Drexel University

9:30 AM Bond PTFE and Metals Together Without Surface Treatments

Lei Wang, TE Connectivity

10:00 AM A Time Dependent Nonlinear Model of Bulk Adhesive Under Static and Cyclic Stress David Lemme, Washington State University

10:30 AM Experimental and Numerical Study of Hybrid Steel-To–Fiber Reinforced Polymer Joints Under Tensile Loading Sarah Mouring, U.S. Naval Academy

Design and Stress Analysis - 2 (Damage) Room: 103A Category Chairs: Sanjib Chowdhury, University of Delaware – Center for Composite Materials (UD-CCM); Ryan Jones, Raytheon; Douglas Kenik, AutoDesk; Jerome Tzeng, US Army Research Laboratory; Brent Volk, Air Force Research Laboratory;

8:00 AM Simplified Virtual Crack Closure Technique (VCCT) for Assessing Disbonds in Large Bonded Structures Patrick O'Callaghan, Northrop Grumman

8:30 AM Delamination Modeling in Multi-Directional Laminates Using Cohesive Zone Methodology Under Static and Dynamic Loading Prakash Jadhav, GE Global Research

9:00 AM Dielectric Assessment of Composite Damage States Vamsee Vadlamudi, University of South Carolina

9:30 AM Development of Damage Sizing Methodology for Composite Landing Gears Structures Arnaud Divialle, Centre technologique en aérospatiale

10:00 AM Determination of Damage Material Properties in Abaqus and Ansys Javier Cabrera, West Virginia University

10:30 AM Stress Analysis or Strength Prediction of Laminated Composite Plates with Rectangular/Square Cutout Using Finite Element Method VijayaKumar Rayavarapu, Hindustan Aeronautics Limited, India

High Temperature Materials & Processing - 1 Room: 102B Category Chairs: Gray Fowler, Raytheon Space and Airborne Systems; Thao Gibson, University of Dayton Research Institute; David Leach, Henkel Aerospace; Tara Storage, Air Force Research Laboratory; Gyaneshwar Tandon, University of Dayton Research Institute; Steven Violette, Fiber Materials Inc.

8:00 AM Cycloaliphatic Epoxide – Properties, Processing and Comparison of New Grades Michael Favaloro, CompositeTechs, LLC

8:30 AM

Imidization and Crosslinking of A PMDA-Type Pepa-Terminated Polyimide in the Polymerization of Monomeric Reactants (PMR) Process with Different Chain Length Xiaochen Li, University of Southern California

9:00 AM High Temperature Phthalonitrile Resins/Polymers For Advanced Applications Matthew Laskoski PhDPhD, Naval Research Laboratory

9:30 AM Preparation and Characterization of Novel Furan-Based Polyimides Santosh Kumar Yadav, Department of Chemical and Biological Engineerig, Drexel University, Philadelphia, PA 19104, USA

10:00 AM Hybridization of Organic Thermosets with Pre-Ceramic Polymers Timothy Pruyn, AFRL/Material and Manufacturing Directorate

10:30 AM The Influence of a Residual Solvent on Thermomechanical Properties of an RTM Benzozazine Resin Jonathan Lo, University of Southern California

Space Technology and Applications - 1 Room: 101B Category Chair: Rachel Kamenetzky, NASA Johnson Space Center

8:00 AM Nasa’s Orion: Materials Make the Spacecraft Mary Jane E. O'Rourke, NASA/Johnson Space Center

8:30 AM Thermal Analysis of Orion EFT-1 Heat Shield Material Mike Fowler, NASA-JSC

9:00 AM The International Space Station (Iss) Solar Alpha Rotary Joint (Sarj): Materials & Processes (M&P) Lessons Learned for a Large, Rotating Spacecraft Mechanism Johnny Golden, Moseley Technical Services

9:30 AM Material Ablative Response Modeling of PICA Jon Langston, University of Texas at Austin

Testing, Materials Characterization, and Qualification - 2 Room: 103C Category Chairs: Madhur Atreya, L&T Technology Services, LLC; Timothy Briggs, Sandia National Laboratories; Jeremy Jacobs, NASA Johnson Space Center; David Miller, Montana State University

8:00 AM Hybrid Sheet Molding Compound Technologies for a New Generation of Cabin and Cargo Aircraft Components Marc Fette, Helmut Schmidt University Hamburg, Institute of Production Engineering / Composite Technology Center Stade (An Airbus Company)

8:30 AM Developing Cure Kinetics Models for Interleaf Particle Toughened Epoxies

James Kratz, University of Bristol

9:00 AM 3D-Woven Fiber-Reinforced Composite for Cad/Cam Dental Application Richard Petersen, University of Alabama at Birmingham

9:30 AM Hygromechanical Coupling and Transverse Failure of Laminated Composites Gil Steinbrecher, Technion - Israel Institute of Technology

10:00 AM Mechanical Properties of 3D Printed Continuous Carbon Fibre Reinforced Thermo-Plastic Tensile Test Bars. Frank van der Klift, Tokyo Institute of Technology

10:30 AM Cure Cycle Development and Qualification for Thick-Section Composites Corinne Warnock, Sandia National Laboratories

Thermoplastics

Room: 102A Category Chairs: James Pratte, Cytec Aerospace Materials and Shridhar Yarlagadda, University of Delaware

8:00 AM Processing, Mechanical and Morphological Properties of Calendered Polypropylene-Discontinuous Carbon Fiber Composites Sam Lukubira, Clemson University

8:30 AM Performance and Simulation of a Thermoplastic PAEK Hybrid Composite System Frank Ferfecki, Victrex USA Inc.

9:00 AM Mechanical Performance of Composite Sandwich Panels Made of Recycled Foamed Polypropylene Core and Glass/PP Skins Mohammadreza Azad, Concordia University

9:30 AM Extrusion of High-Performance Polyetherimide Pipe Systems for Aircrafts Michael Stegelmann, Institute of Lightweight Engineering and Polymer Technology (ILK), TU Dresden

10:00 AM Three Dimentional Parts From Thick Peek / Carbon Fiber Billets Sean Reymond, Impact Composites

10:30 AM Continuous Thermoforming of Unidirectional Fiber Reinforced Tapes for The Manufacturing of 3D Lightweight Components Clemens Buschhoff, Fraunhofer Institute for Production Technology IPT

Nanocomposites, Nanotechnology Challenges and Solutions - 1 Room: 102C Category Chair: George Jacob, Dow Chemical Company

9:30 AM Eco-friendly Dyeing of Cellulose Nanofibers with Reactive Dye Soudabeh Hajahmadi, Najafabad Branch, Islamic Azad University

10:00 AM Weak Formulation of the Heat Conduction Problem in Multiscale Heterogeneous Media with Perfect Interface Contact Using Reiterated Homogenization Manuel Cruz, PhD, UFRJ-Federal University of Rio de Janeiro

10:30 AM Oxidizer Influence on Organic Flexible Conductive Composite Properties Benoit Bideau, Lignocellulosic Materials Research Center

Wednesday Afternoon Ballistic Materials and Applications Room: 102A Category Chairs: Bazle Z. Gama, University of Delaware; Brian Kopan, The Protective Group - A Division of Point Blank Enterprises; Ravhi Kumar, University of Nevada Las Vegas; Gaurav Nilakantan, Teledyne Scientific & Imaging; Timothy Talladay, US Army TARDEC; Lionel Vargas-Gonzalez, U.S. Army Research Laboratory

1:30 PM PBO COMPOSITE HARD ARMOR Nick Gramly, The Protective Group

2:00 PM Composite Armor Enclosure Design Shawn Klann, U.S. Army TARDEC

2:30 PM Durability-After-Impact of Ultra-High Molecular Weight Polyethylene Armor Composites Lionel Vargas-Gonzalez, U.S. Army Research Laboratory

3:00 PM Fillet Radius Edge Effect on RCC Fragmentation Projectiles Russell Caspe, Gentex Corporation

3:30 PM Novel Processing Apparatus to Control Multi-Scale Morphology in Ultra High Molecular Weight Polyethylene Fibers Chris Henry, Drexel University

4:00 PM Modeling Transverse Impact on Uhmwpe Soft Ballistic Armor Pack (SBAP): A Finite Element Study Bazle Haque, University of Delaware

Design and Stress Analysis - 2 Room: 103A Category Chairs: Sanjib Chowdhury, University of Delaware – Center for Composite Materials (UD-CCM); Ryan Jones, Raytheon; Douglas Kenik, AutoDesk; Jerome Tzeng, US Army Research Laboratory; Brent Volk, Air Force Research Laboratory;

1:30 PM

General Stability Analysis of Composite Sandwich Plates Under Thermal Load Shaher Kassaimah, PhD. California State University, Long Beach

2:00 PM Effect of Fiber Morphology on the Elastic Properties of Statistically Equivalent Uncorrelated Volume Elements Seyed Hamid Reza Sanei, University of Wyoming

2:30 PM Discontinuous Long-Fiber Thermoplastic Composite Replacement for Complex-Shape MetaLlic Helicopter Fairing Rib Simon O'Neill, Greene, Tweed & Co. Ltd.

3:00 PM Trace as the One Critical Starting Point for Design and Testing of Composite Materials Stephen Tsai, Stanford University

3:30 PM A Comparison of Hydrostatic And Plastic Yield Criteria for A Toughened Adhesive Preetam Mohapatra, Washington State University, Pullman, WA

4:00 PM Predicting Stress Relaxation Behavior of Fabric Composites Using Finite Element Based Micromechanics Model Anand Vijay Karuppiah, Wichita State University

4:30 PM Assessment of Predictive Capabilities of Progressive Damage Analysis Methods Using High Fidelity Experiments for Validation Joseph Schaefer PhD, The Boeing Company

High Temperature Materials & Processing - 2 Room: 102B Category Chairs: Gray Fowler, Raytheon Space and Airborne Systems; Thao Gibson, University of Dayton Research Institute; David Leach, Henkel Aerospace; Tara Storage, Air Force Research Laboratory; Gyaneshwar Tandon, University of Dayton Research Institute; Steven Violette, Fiber Materials Inc.

1:30 PM Dielectric Spectroscopy of High-Temperature Polymer Matrix Composites: Challenges and Opportunities Johnathan E. Spowart, United States Air Force

2:00 PM Evaluation of High Temperature Polyimide Neat Resins for the Next Generation of Engine/Propulsion and Hot Air Frame Applications Thao Gibson, University of Dayton Research Institute

2:30 PM Processing and Properties of Phenylethynyl-Terminated PMDA Type Polyimide Composites Yixiang Zhang, University of Southern California

3:00 PM Processing and Characterization of Carbon Nanotube/Core Shell Siloxane Modified High Temperature Bismaleimide Polymeric Composites Shaik Zainuddin, Tuskegee University

Nanocomposites, Nanotechnology Challenges and Solutions - 2 Room: 102C Category Chair: Bhawesh Kumar, The Dow Chemical Company

1:30 PM Interfacial Evaluation of Carbon Frinforced Nano-Composites Using Electrical Resistance Measurement with Wetting Tests Joung-Man Park, PhD. Gyeongsang National University

2:00 PM Improved Toughness and Fatigue Performance of Carbon Fiber Composites from Nanosilica Modified Fiber Sizing Kunal Kumar, Evonik Corporation

2:30 PM Short Beam Strength of Laminated Fiberglass Composite with and Without Electospun Teos Nanofibers Dattaji Shinde PhD, Joint School of Nanoscience and Nanoengineering (JSNN)

3:00 PM A New Class of Lightweight Multifunctional Material to Improve Size, Weight, and Power Joseph Sprengard Jr., General Nano, LLC

3:30 PM Effects of Functionalization Methods and Geometrical Configurations of Carbon Nanotubes on Properties of Polymeric Nanocomposites Ali Ghazinezami, Wichita State University

4:00 PM Effects of Distribution/Dispersion of Nano-Sized Pigment and Temperature on Flexural Properties of an Epoxy Resin System Yanan Hou, Downhole Technology LLC

4:30 PM Dispersion and Stabilization of Mwcnts in an Epoxy Prepolymer Matrix Via Contunuous Reactor Processing Andrew Frazee, University of Southern Mississippi

Out of Autoclave Technology Room: 101A Category Chairs: Suresh Advani, University of Delaware – Center for Composite Materials (UD-CCM); Orlando Mijares, Raytheon Missile Systems; James Sutter, SCRA Applied R&D

1:30 PM In-Situ Observation Of Void Transport During Vacuum Bag-Only Cure Wei Hu, University of Southern California

2:00 PM Evaluation of Out of Autoclave Composite Properties Manufactured From a Soluble Self-Pressurizing Tooling Zachary Wing, Advanced Ceramics Manufacturing

2:30 PM Preforming of 3d Carbon Interlock Fabrics for the Manufacturing of Composite Parts with the Flexible Injection Process

Joffrey Renaud, Polytechnique Montréal

Space Technology and Applications - 2 Room: 101B Category Chair: Rachel Kamenetzky, NASA Johnson Space Center

1:30 PM Uv Protective Oxide Coatings for Cyanate Esters Jessica Piness, University of Southern Mississippi

2:00 PM Hybrid Composite Radiation Sheilding Raghavan Jayaraman, University of Manitoba

Testing, Materials Characterization, and Qualification - 3 Room: 103C Category Chairs: Madhur Atreya, L&T Technology Services, LLC; Timothy Briggs, Sandia National Laboratories; Jeremy Jacobs, NASA Johnson Space Center; David Miller, Montana State University

1:30 PM Mixing Methodology and Glass Transition Temperatures of Polylactic Acid Containing Additives Ryan Foley, Montana Tech of The University of Montana

2:00 PM Performance and Strength Prediction of Composite Materials Based on Dielectric Property Investigation Md Rassel Raihan, University of Texas at Arlington Research Institute

2:30 PM On The Shielding Properties of Carbon Fiber Reinforced Plastic Composites in Magnetic Near Fields with Low Kilohertz Frequency Michael Holzer, Daimler AG

3:00 PM Identifying The Strain-Free Temperature of Non-Symmetric Cycom 5320-1 Laminates with Digital Image Correlation Kyler Knowles, University of Southern Mississippi

3:30 PM Bending Characterization of Axis and Off-Axis Fiber-Reinforced Hinges at Large Deflection Jan Krollmann, Technische Universität München

4:00 PM Characterization of Process-Induced Variation in Electrical Properties of Injection Molded Liquid Crystalline Polymer Mark Shooter, Tufts University

4:30 PM Design of Experiments as A Tool for Optimizing Insulating Compound Mixtures Andres Garcia, University of North Texas

Non-Traditional Approaches to Alternate Energy Room: 101B Category Chair: Neel Sirosh, LightSail Energy

2:30 PM Electrospun Carbon Nanofiber Based Catalyst Support for Proton Exchange Membrane Fuel Cell Sophia Chan, University of British Columbia

3:00 PM The Potential for Making Solar Cells Out of Depleted Urania Thomas Meek PhD, The University of Tennessee at Knoxville

Additive Manufacturing - 3 Room: 101A Category Chairs: Teresa Clement, Raytheon Company; Jennifer Fielding, Air Force Research Laboratory; Richard Martukanitz, Penn State CIMP-3D; and R. Byron Pipes, Purdue University

3:00 PM Development of Three-Dimensional Thermo-Mechanical Finite Element Model for Prediction of Thermal Deformation During Selective Laser Sintering Processes Mohammad Razzaghian, University of Missouri

3:30 PM 3D Printing Manufacturing Simulation of Thermoplastic Nano Graphene Inclusion Frank Abdi PhD, Alpha STAR Corporation

4:00 PM Digital Data Requirements for Powder Bed Fusion Additive Manufacturing and the Implementation of A Transparent Communication Architecture Abdalla Nassar, Applied Research Laboratory at Penn State Univ.

4:30 PM A Demonstration of Additive Manufacturing as an Enabling Technology for Rapid Satellite Design and Fabrication Melissa Orme PhD, Morf3D

Advanced Processing - 1 Room: 101B Category Chairs: Ehsan Barjasteh, California State University Long Beach; Axel Boettcher, Boettcher Consult; Timotei Centea, University of Southern California; Michael Maher, DARPA

3:30 PM Composite Ring Made of 3D Woven Preform Injected by RTM: From Design to Full Scale Testing Bernard Poulaert, Sonaca

4:00 PM Effect of Laminate Structure on Flow Induced Deformation of Fiber Preform in Resin Transfer Molding Dong Gi Seong, Korea Institute of Materials Science

4:30 PM Automated Fiber Placement & Forming - Process Simulation Matthieu Dupuis, Coriolis Composites

Emerging Material - 1 Room: 102B

Category Chairs: Greg Ehlert, Air Force Research Laboratory; Lessa Grunenfelder, University of Southern California; George Hansen, Conductive Composites Company; Gregory Yandek, Air Force Research Laboratory

3:30 PM Plasma and Particles Petr Spatenka PhD, Czech Technical University in Prague

4:00 PM Encapsulation of Maleimide-Based Healing Agent and Reversible Diels-Alder Chemistry for Self-Healing and Corrosion Prevention Sadella Santos, Drexel University

4:30 PM Model Epoxy/Amine Coating Binders: Their Synthesis and Characterization John Vergara, Drexel University

Thursday Additive Manufacturing - 4 (Composites and Tooling) Room: 102B Category Chairs: Teresa Clement, Raytheon Company; Jennifer Fielding, Air Force Research Laboratory; Richard Martukanitz, Penn State CIMP-3D; and R. Byron Pipes, Purdue University

8:00 AM Additive Manufacturing of Multifunctional Components Using High Density Carbon Nanotube Yarn Filaments John Gardner, NASA Langley Research Center

8:30 AM Microstructural Modeling of Fiber Filled Polymers in Fused Filament Fabrication Anthony Favaloro, Purdue University

9:00 AM 3D Printed Continuous Carbon Fiber Reinforced Thermoplastic by In-Situ Impregnation Technique Masahito Ueda PhDPhD, Nihon Univesrity

9:30 AM Materials and Process Development for Direct Digital Manufacturing of Vehicles Charles Hill, Local Motors

10:00 AM Design Guide Development for Additive Manufacturing (FDM) of Composite Tooling Timothy Schniepp, Stratasys

10:30 AM 3D Printed Dissolvable Molds for Composite Applications Narender Lakshman, North Carolina State University, Raleigh, NC, 27695

11:00 AM Additive Manufacturing of Composite Tooling Using High Temperature Thermoplastic Materials Ahmed Hassen, Oak Ridge National Laboratory (ORNL)

Advances in Manufacturing Automation

Room: 101A Category Chairs: Sayata Ghose, The Boeing Company; Jessica Hughes, Boeing Commercial Airplanes; Ali Yousefpour, National Research Council Canada; Wenping Zhao, United Technologies Research Center

8:00 AM Influence of Laser Power Density on The Meso-Structure Of Thermoplastic Composite Preforms Manufactured by Automated Fibre Placement Mattia Di Francesco, The National Composites Centre

8:30 AM Consolidated Fiber Placement - Cutting of Consolidated Fiber Tapes Andreas Henneberg, Technical University Braunschweig - Institute of Adaptronics and Functional Integration

9:00 AM Characterization of Prepreg Tack to Aid Automated Material Placement Sayata Ghose, The Boeing Company

9:30 AM Fabric and Textile 3D Permeability Characterization Work-Station Minyoung Yun, University of Delaware

10:00 AM A+ Glide Forming Technology Jordi Brufau Sr., Applus

10:30 AM Automated Layup of Sheet Prepregs on Complex Moulds Michael Elkington PhDPhD, Bristol University

11:00 AM Enhancing Electrical Conductivity and Device Performance of Aerosol Jet Printed Patch Antenna and Strain Sensor for Composite Applications Sabrina Siddique, High Performance Materials Institute, Electrical and Computer Engneering, FAMU-FSU College of Engineering

Design and Stress Analysis - 4 Room: 103A Category Chairs: Sanjib Chowdhury, University of Delaware – Center for Composite Materials (UD-CCM); Ryan Jones, Raytheon; Douglas Kenik, AutoDesk; Jerome Tzeng, US Army Research Laboratory; Brent Volk, Air Force Research Laboratory;

8:00 AM Dimensions on Day One Denise Shimazu, Northrop Grumman Corporation

8:30 AM Impact Damage Analysis of Discontinuous Long-Fiber Thermoplastic Composite Plates Adnan Khawaja, Greene, Tweed & Co.

9:00 AM State-Of-The-Art Finite Element Modeling of Rotorcraft Main Rotor Blade Root End for Bird Strike Damage Analysis Vijayakumar Rayavarapu, Rotary Wing R&D Center, HAL

9:30 AM

Integrated Process And Structural Modeling Frameworks for Nonlinear Analysis of Discontinuous Long-Fiber Thermoplastic Composites Hakan Kilic, Greene, Tweed & Co.

Fire Safety Materials - 1 Room: 102A Category Chairs: Fei Liang, Embraer Engineering and Technology Center; Mike Strader, Pharr Yarns, LLC; Aixi Zhou, The University of North Carolina at Charlotte

8:00 AM Development Of New Low-Viscosity Bio-Based Ablative Resins For Thermal Protection Systems Bastien Rivieres, Airbus Defence and Space

8:30 AM Synergistic Flame Retardancy of Epoxy/Melamine Phosphate-Borate/Magnesium Hydroxide Composites Yanmao Dong PhD, Suzhou University of Science and Technology

9:00 AM Effects of Weathering on Performance of Intumescent Coatings Babak Bahrani, University of North Carolina at Charlotte

9:30 AM Surface Morphology and Flammability of Two Flame Resistant Fibers and Their Blended Nonwoven Fabrics Lan Yao PhD, The University of Texas at Austin

10:00 AM Development of an FST/OSU Passing Rigid Polyurethane Foam for the Aerospace Industry Hester Clever PhD, General Plastics Manufacturing Company

10:30 AM Flame Retardant Nylon 6 Fibers by Melt-Spinning Andrew Frazee, University of Southern Mississippi

11:00 AM Composite Floating Beads: A New Method of Vapor Suppression and Fire Prevention for Flammable Liquids Including LNG and LPG Robert Kelly, Trelleborg Applied Technologies

Nanocomposites, Nanotechnology Challenges and Solutions - 3 Room: 102C Category Chairs: Ayou Hao, Florida State University

8:00 AM Micromechanical Stiffness Predictions at The Nano-Scale: Carbon Nanotube Reinforced Composites Eric Neer, California State University, Long Beach

8:30 AM A Laser Interference-Based Surface Treatment of Aluminum And Carbon Fiber Polymer Composites for Enhanced Bonding Adrian Sabau, Oak Ridge National Laboratory

9:00 AM Amorphous Nickel-Phosphorus Nanofibers for Borohydride Electro-Oxidation

Garriott Yip, University of British Columbia

9:30 AM Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Composites Jin Ho Kang, National Institute of Aerospace

10:00 AM Development of New Thermal Protection Systems Based on Polysiloxane/Silica Composites: Properties Characterization I Kurt Schellhase, Univeristy of Texas at Austin

10:30 AM Computational Investigation of Mechanical Properties of Functionalized Boron Nitride Nanotubes Mahdi Ghazizadeh, Huntsman

11:00 AM Graphitic Crystal Morphology and Failure Modes of Collapsed and Aligned Carbon Nanotubes in Nanocomposites Rebekah Downes, Florida State University / High-Performance Materials Institute

NSF-G8 Increasing Manufacturing Efficiency Room: 101B Category Chairs: Doug Decker, Northrop Grumman Corporation; Gail Hahn, Boeing Research & Technology; Steve Nutt, University of Southern California

8:00 AM Reclaiming In-Process Composite Waste for Use in Energy Absorbing Sandwich Structures Jamie Hartley, University of Bristol

8:30 AM Manufacturing Efficiency for Vacuum Bag-Only Prepregs: Overview and Lessons Learned Steven Nutt, University of Southern California

9:00 AM Modelling Void Formation in Corners During Out-Of-Autoclave Prepreg Processing Roland Hinterhölzl, TU München / Institute for Carbon Composites

9:30 AM Evaluating Consolidation Dynamics – Study of Key Consolidation Parameters in a Vacuum Bag Only (VBO) Cure Stephen Howard, Cytec Industries - Aerospace Materials

Testing, Materials Characterization, and Qualification - 4 Room: 103C Category Chairs: Madhur Atreya, L&T Technology Services, LLC; Timothy Briggs, Sandia National Laboratories; Jeremy Jacobs, NASA Johnson Space Center; David Miller, Montana State University

8:00 AM Influence of Out-Time on the Processing and Properties of FM 300-2 Film Adhesive and IM7/8552-1 Aluminum Honeycomb Sandwich Panels* Tiffany Williams PhD, NASA Glenn Research Center

8:30 AM Failure Envelope Validation of Composite Laminates and Enviromental Effect Frank Abdi PhD, Alpha STAR Corporation

9:00 AM Impact and Post Impact Delamination Evolution of Toughened Aero Grade Benzoxazine Panel Frank Abdi PhD, Alpha STAR Corporation

9:30 AM Investigating the Effects That Alternative Turbine Engine Fuels Might Have on the Mechanical Properties of an Epoxy Resin System Ronald Sterkenburg, Purdue University

10:00 AM Effects of Saltwater Saturation on The Static Strength and Acoustic Emission Signatures of Epoxy Glass Composites David Miller, Montana State University

10:30 AM Flexural Properties and Fracture Behavior of Unidirectional Thermoplastic and Thermosetting Composite Laminates Yan Ma, Kyoto Institute of Technology

11:00 AM Interfacial Characterization of A Functionalized Cellulosic Fiber Reinforced Pla Composites MReza Foruzanmehr, University of Sherbrooke

Advanced Processing - 2 Room: 101B Category Chairs: Ehsan Barjasteh, California State University Long Beach; Axel Boettcher, Boettcher Consult; Timotei Centea, University of Southern California; Michael Maher, DARPA

10:00 AM Understanding the Consequences of Tooling Design Choices on Thermal History in Composites Processing Janna Fabris, Composites Research Network (The University of British Columbia)

10:30 AM Hand Lay-Up of Complex Geometries – Prediction, Capture and Feedback Dennis Crowley, ACCIS, Uniersity of Bristol

11:00 AM Drilling of Stackup Composite Structures with Automatic Drilling Units Equipped With CO2 Cooling Technology Nelson Sorbo PhD, Cool Clean Technologies

Optimization and Simulation - 1 Room: 103A Category Chairs: Frank Abdi , AlphaSTAR Corporation; Robert Yancey, Altair Engineering;

10:00 AM Context Aware Computing Leverages the Industrial Internet of Things (IIOT) to Create a Rich Digital Context and Weave the Digital Thread for Automated and Optimized Decision Making in Composites Manufacturing Avner Ben-Bassat, Plataine Technologies

10:30 AM

Development of Robust Organic Matrix Composite Cure Cycles Using Predictive Pareto Genetic and Constraint Satisfaction Algorithms Brent Volk, Air Force Research Laboratory

11:00 AM Dual-Scale Flow and Thermo-Chemo-Rheological Coupling Simulation for On-Line Mixing Resin Transfer Molding Process Mathieu Imbert, ESI Group / Ecole Centrale de Nantes

Thursday Afternoon Advanced Processing - Modifications Room: 102B Category Chairs: Ehsan Barjasteh, California State University Long Beach; Axel Boettcher, Boettcher Consult; Timotei Centea, University of Southern California; Michael Maher, DARPA

1:30 PM Comparison of Integrated Rib Stiffened and L Blade Stiffened Composite Panels Manufactured Using Simple Tooling Methods J. Marcelo Müller, Netherlands Aerospace Centre

2:00 PM Aerogel Core CFRP Curved Sandwich Composites with Variable Cross-Section Without Ply-Drop for Body Protection and Rehabilitation Sunil Joshi, Nanyang Technological University

2:30 PM Polymer Lined Copvs Formed Using an Integrally Heated Rotational Moulding Tool and Laser Assisted Tape Placement Brendan Murray, NUI Galway

3:00 PM Bi-Angle Tape for Automated Tape Laying Stephen Tsai, Stanford University

Emerging Material - 2 Room: 103C Category Chairs: Greg Ehlert, Air Force Research Laboratory; Lessa Grunenfelder, University of Southern California; George Hansen, Conductive Composites Company; Gregory Yandek, Air Force Research Laboratory

1:30 PM Jute Bio-Nanocomposites Reinforced with Grafted Halloysite Nanotubes Added Phbv Polymer Shaik Zainuddin, Tuskegee University

2:00 PM Development of Multifunctional and Multisensing Nanocomposite Foam with Dual Piezoresponsive Nature Cory Newton, Brigham Young University

Fire Safety Materials - 2 Room: 102A

Category Chairs: Fei Liang, Embraer Engineering and Technology Center; Mike Strader, Pharr Yarns, LLC; Aixi Zhou, The University of North Carolina at Charlotte

1:30 PM Mg Resins For Low-Flammability, High Temperature Applications Richard Hreha, Cornerstone Research Group

2:00 PM Lignin Biopolymer as A Green Alternative for Preparing Phenolic Foam Louis Pilato, Pilato Consulting

Nanocomposites, Nanotechnology Challenges and Solutions - 4 Room: 102C Category Chair: Daniel Braley, Boeing Research & Technology

1:30 PM CARBON NANOTUBE REINFORCEMENT FOR COMPOSITE ARMOR Tyrone Mlnton, The Protective Group

2:00 PM Fabrication and Characterization of Polymeric Coating for Abrasion Resistance Kenan Song, MIT

2:30 PM Role of Interfaces in Polymer Matrix Composites and Methodologies to Improve and Characterize Interfaces in Composites Ranji Vaidyanathan, Oklahoma State University

3:00 PM Fabrication and Characterization of Carbon Nanotube/Carbon Fiber/Polycarbonate Multiscale Hybrid Composites Young-Bin Park, Ulsan National Institute of Science and Technology (UNIST)

3:30 PM Synthesis of Graphene-Metal Nanocomposite Anode Materials for Lithium Ion Batteries Osman Eksik PhD., Istanbul Technical University

4:00 PM Single-Walled Carbon Nanotube Added Epon 862 Nanocomposites: Investigating the Crosslinking Behaviour and Interfacial Properties Through Molecular Dynamics Simulations Shaik Zainuddin PhD, Tuskegee University

4:30 PM Compressive Strain Sensing Using Carbon Nanotube/Graphene Nanoplatelet/PDMS Hybrid Nanocomposites Young-Bin Park, Ulsan National Institute of Science and Technology

Optimization and Simulation - 2 Room: 103A Category Chairs: Frank Abdi , AlphaSTAR Corporation; Robert Yancey, Altair Engineering;

1:30 PM Analytical Study of Delamination Arrest Features in Abaqus Fea Luke Richard, University of Washington

2:00 PM Structural Design Optimization of Short-Fiber Composite Parts Considering Manufacturing Aspects Markus Schatz, Institute of Lightweight Structure, TU Munich

2:30 PM Integrated Computational Methods for Composite Materials (Icm2): Process and Micromechanics Modeling for Airframe Applications Bob Koon, Lockheed Martin Aeronautics, Advanced Development Programs

3:00 PM 3D Resistor Network Model for Predicting Electrical Conductivity of CFRP Hong Yu, Center for Composite Materials

3:30 PM Design-Optimization of A Curved Layered Composite Panel Using Efficient Laminate Parameterization André Mönicke, Componeering Inc.

4:00 PM Optimization and Sensitivity Analysis of Pultrusion Process Parameters Based on Numerical Simulation Alexander Safonov, Skolkovo Institute of Science and Technology

Textiles: Weaving and Braiding, Fiber Innovations Room: 101B Category Chairs: Vince Bailey, Composites Specialists; Anand Rau, Crosslink Technologies; Alex Weldon, Firefly Space Systems

1:30 PM Roll Forming for Multi-Material Composites Tobias Reincke, Technische Universität Braunschweig - Institute of Joining and Welding

2:00 PM Advances in Multidirectional Thermoplastic Towpreg Michael Favaloro, COmpositeTechs, LLC

2:30 PM Computational Fluid Dynamics (CFD) Analysis for Off-Gas Mixing and Ventilation Inside Carbonization Furnace During Pan-Based Carbon Fiber Manufacturing T.S. Lee PhD, Harper International

3:00 PM Complex 3d Shaped Knitting Preforms Tamer Hamouda PhD, National Research Centre

3:30 PM Automated Braiding of Dry Preforms for Aerospace Structural Components Philippe Monnot, École Polytechnique de Montréal

4:00 PM The Ban of CMR (Carcinogenic, Mutagenic And Repro Toxic) Solvents by Law and its Consequences for Textile Fiber and Carbon Fiber Production Stefan Peterek, Institute of Textile Technology at RWTH-Aachen University

4:30 PM Towards the Development of A Machine Vision System for Tubular Braided Composite Materials Alexander Hunt, University of Alberta

Incorporation of Advanced Materials into Civil/Infrastructure Applications Room: 103C Category Chairs: Kunal Kumar, Evonik Corporation

2:30 PM Recycled Aggregate for High-Performance Concrete Jun Wang, university of colorado denver

3:00 PM Development of Nanocellulose-Polyvinyl Butyral Composites for Armored Glass Chloé Maury, Lignocellulosic Materials Research Centre

3:30 PM Bending Behavior of Carbon/Epoxy Composite Isobeam Structures David Jensen PhD, Brigham Young University

4:00 PM Hygrothermal Effect on Concrete Columns Confined With CFRP Abulgasem Elarbi PhD, University of Tripoli

4:30 PM Experimental and Finite Element Analysis of FRP Section for Hydraulic Gates Piyush Soti, West Virginia University

Repair of Damaged Structures and Health Monitoring Room: 102A Category Chairs: Sarah Cox, NASA; Pradeep Krishnaswamy, The Boeing Company; David Lowry, NASA

2:30 PM In-Situ Ablation Sensing Using Type-C Thermocouples Landon Mosley, University of Texas

3:00 PM Structural Injection Repair Resin and Process for Composite Materials Brian Hayes, Applied Poleramic, Inc.

3:30 PM Wet Layup Composite Bonded Scarf Repairs: Effect of Processing Variables on Porosity Andrew MacLean, McGill University

4:00 PM Efficient and Flexible Heating Technology Using Induction Marvin Schneider, German Aerospace Center (DLR)

4:30 PM Revolutionary Repairs for Modern Aircraft Structure Larry Ridgeway, John Hoffman, The Boeing Company

Tooling Technologies Room: 101A Category Chairs: David Dickson, The Boeing Company; Louis Dorworth, Abaris Training Resources, Inc.; Robert Greenberg, Honda Aircraft; Craig Yellin, Tencate Advanced Composites

2:30 PM

Universal Model Development of The Human Ankle Foot Region for Ply Pattern Generation for the Manufacturing of Passive Dynamic Ankle Foot Orthotics Francis Fish, University of Delaware Center for Composite Materials

3:00 PM Effect of Cyclic Heating on Silicone Rubber Materials for Elastomeric Tooling Antonio Paesano PhD, The Boeing Company

3:30 PM Porosity-Free Molded Surfaces for Out-Of-Autoclave Composites Mikhail Grigoriev, Aerospace Materials Processing

4:00 PM Trapped Tooling for Selectively Stiffened Lightweight Composite Structures Mathias Hecht, Rubbercraft

4:30 PM A Drilling Method of CFRP and Titanium Plate by A Solid Lubricating Sheet Yousuke Matsuyama, Yonezawa Dia Electronics Co., Inc./Sheet Product Dept./Sheet Technology Development sect.

Additive Manufacturing - 5 Room: 102B Category Chairs: Teresa Clement, Raytheon Company; Jennifer Fielding, Air Force Research Laboratory; Richard Martukanitz, Penn State CIMP-3D; and R. Byron Pipes, Purdue University

3:30 PM Process Parameter Effects on Bond Strength in Fused Filament Fabrication Andrew Abbott, University of Dayton Research Institute

4:00 PM Economics of Composite Tooling Made Via Additive Manufacturing Nicholas DeNardo, Purdue University

4:30 PM Additive Manufacturing with Composites for Integrated Aircraft Structures Daniel-Alexander Türk, Product Development Group Zurich, ETH Zürich

Emerging Material - 3 Room: 104A Category Chairs: Greg Ehlert, Air Force Research Laboratory; Lessa Grunenfelder, University of Southern California; George Hansen, Conductive Composites Company; Gregory Yandek, Air Force Research Laboratory

4:00 PM Curing Carbon Fiber Composites for Automotive Applications Anthony Berejka, Ionicorp+

4:30 PM Characterization of Furanyl Thermosetting Polymers with Superior Mechanical Properties and High-Temperature Char Yield Fengshuo Hu, Drexel University