www.fiberonhomeselect.com800.318.7828

INSTALLATION INSTRUCTIONSCLASSIC RAILING

Manufactured by

FHS-0003-LIT 5/15

After carefully measuring between level and plumb posts, cut top and bottom guardrails to length. Slide bottom rail brackets over ends of bottom rail.

Cover 4x4 posts or Fiberon Homeselect surface mount bracket (Item# 345061) with post sleeve and verify spacing. Posts should be plumb in both directions.

Center crush block on deck surface between posts. Set bottom rail on top of crush block.

Place the bottom rail between the post sleeves using crush block to support and level the bottom rail.

Note: Fiber Composites LLC actively works to improve the performance and installation of our Lowes’ Fiberon HomeSelect guardrail systems. Recent improvements have been added into the time tested brackets previously supplied to make the Lowes’ Fiberon HomeSelect guardrails even stronger and more adaptable than before. No matter which style, Fiber Composites LLC stands behind the quality and performance of every guardrail system.

1

2

3

Bottom Rail

Crush Block

The most recent installation instructions can be found our website. Please visit www.fiberonhomeselect.com or call customer service at 800-318-7828.

NOTE: If using the post sleeve collar, make sure to position and glue collars in place prior to securing the bottom rail.

Classic Rail Installation Instructions

Maximum length between posts:6ft Rail = 72-in.8ft Rail = 96-in.

NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing.

Classic Railing Installation Instructions

Required Tools and Supplies:

Classic Top Rail Profile

Classic Bottom Rail Profile

• Power Drill • 1/8-in. Drill Bit• #2 Square Head Bit• Protective Eye Wear• Tape Measure• Level

• Screw Driver, Phillips #2• Speed Square• Miter Saw• Pencil• Adjustable Square

Railing component list for each section:

Post SleeveCap

Top Rail Bracket

BracketFlange

Top Rail

Bottom Rail

SquareBalusters

Bottom Rail Bracket

YES2-in. minimum from rail end to hole

NO

Post Sleeve

Post Sleeve Collar Crush

Block

Prior to installing railing: Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. All supporting structures must be in accordance with applicable building codes. Neighborhood associations and/or historic districts may regulate size, type, placement and type of railing. Apply for permits if required by local authorities and codes. Ensure compliance prior to installation. Local building code requirements will always supersede any and all suggested procedures and measurements in the following installation. The following installation instructions are intended as a general guideline based on common building practices used in railing installation.

When railing span is greater than the distance between posts, trim both top and bottom rail ends to maintain uniform baluster spacing. Measure distance, subtract 1/2-in. from measurement (1/4-in. on each side) to allow for brackets and flanges. Slide post sleeve collar over each post prior to installing bottom rails and press securely into place.

Rail Installation: Trim both ends of rail to maintain uniform baluster spacing. It is critical to ensure the trim mark does not create an openbaluster Insert hole at the end of the rail where the bracket is attached. Adjust trim lines to maintain uniform baluster spacing

Bottom Rail Bracket

Top Rail Bracket

NOTE: For best results, cut post sleeves with a 10-in. circular carbide-tipped blade, minimum 32-tooth.

Place bottom rail brackets onto both ends of bottom rail.

Place bottom rail on top of crush block between post sleeves.

Snap/lock bottom rail in place. Glue crush block to bottom rail.

Insert one baluster into the outermost routed hole at each end.

If using round metal balusters, insert rail Inserts for round balusters into the top and bottom rail routed holes. Place round metal baluster through the inserts. (Round balusters must be a minimum of 32-in. long).

Remove bottom rail and mark bottom bracket flange holes.

Pre-drill holes: 1/8-in. bit. Attach bottom bracket flange.

Pre-drill holes with a 1/8-in. bit and attach the top bracket flange.

Place top rail brackets over each end of top rail.

Carefully position top rail and brackets between the posts. Lower until fully seated onto balusters.

Remove top rail and mark the location of the bracket flange.

Insert all balusters in bottom rail.

4

A

Lightly trace a line to show the location of the bottom of bracket.

B

5

6

7

8

10

9

11

For horizontal angle applications, use metal angle bracket mounted on corner of post sleeve as illustrated above.

ClassicRail Angle Installation:

Place top rail brackets on both ends of top rail.

Seat balusters into top rail. Press down on brackets to snap/lock top rail in place.

To secure the top rail, pre-drill two holes in the flange at the bottom of the bracket 2 ½-in. deep with a 1/8-in. bit.

Secure the top rail using (2) supplied #10 x 2 ½-in. screws. Do not over tighten.

Glue post sleeve cap onto post sleeve.

12

13

14

C

20

17

18

19

1615

The most recent installation instructions can be found our website. Please visit www.fiberonhomeselect.com or call customer service at 800-318-7828.

Classic Line Rail Installation Instructions Classic Line Rail Installation Instructions

Angle Bracket(Available Special Order)

Maximum length of rail for even baluster spacing between post sleeves: 6-ft Rail: 66 1/4-in.8-ft Rail: 90 3/4-in.

Maximum inside length between post sleeves:6-ft Rail = 56 3/16-in.8-ft Rail = 77 1/4-in.

Place the square baluster stair Insert or round baluster stair insert into the bottom rail holes, making sure to align them properly. Place square baluster stair Insert or round baluster stair insert into the top rail as well.

Tip: Pinching the insert wings inward makes insertion easier.

Starting from one end and working towards the other and with all balusters in place, lower the top rail and brackets into position, guiding the balusters into the top rail Inserts.

Pre-drill the holes for the brackets and secure using the supplied pan head screws.

Finish the installation by gluing on the post sleeve caps and the crush block with a quality exterior adhesive.

NOTE: The slope of the stairs can be 30-36 degrees (an 11-in. run and a 7-in. rise results in a 32 degree slope).

Establish the angle by laying the bottom rail in front of the secured posts, and marking the angles making sure to center the baluster holes between the posts. Align the top rail with the bottom rail to ensure the baluster holes will align properly before marking the angle for the top rail and brackets.

When using square or turned balusters, the balusters will need to be cut to appropriate length and angle. Transfer the angle using a tool like an adjustable carpenter’s square. It is critical that all balusters are the same length and angle for best appearance.

Install 4x4 posts in the pre-determined locations, cover with post sleeve and verify spacing. Posts should be plumb in both directions. If using post sleeve collar, slide collar over post sleeve prior to installing rails.

1 2

B

A

4

3 5

5

6

The most recent installation instructions can be found our website. Please visit www.fiberonhomeselect.com or call customer service at 800-318-7828.

NOTE: For best results, cut post sleeves with a 10-in. circular carbide-tipped blade, minimum 32-tooth.

NOTE: If using the post sleeve collar, make sure to position and glue collars in place prior to securing the bottom rail.

NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing.

Classic Stair Rail Installation Instructions Classic Stair Rail Installation Instructions

Top Stair Brackets

UpperBracket

LowerBracket

UpperBracket

LowerBracket

Screws

Bottom Stair Brackets Bottom Stair Brackets

Cut bottom rail to proper length, then align the hole pattern with the top rail and transfer the cut angle.

Insert the bottom vertical bracket into both ends for the bottom rail.

Remove the rail and brackets, and pre-drill with 1/8-in. bit. Secure bottom rail using supplied 1 ½-in. screws. Do not overtighten.

Place the lower rail and brackets in place, and locate and mark the screw holes.

2

3

www.fiberonhomeselect.com800.318.7828

Design Grid