SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the...

SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd

SMMT Type Approval Workshop

Wednesday 25 April 2012

CV Show, NEC, Birmingham


Welcome address

Tony Hopkins. Technical Manager, SMMT

SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 3

Introduction to the content of the workshop

• Automotive legislation is continually moving and changing.

• The following is to try and give you and idea of how to approve a particular type of vehicle (N3) as part of a multi-stage build process.

• The tools to assist you.


Agenda

Time Subject Speaker

09:45 – 10:00 Registration - Commercial Vehicle Workshop refreshments

10:00 – 10:05 Welcome Tony Hopkins, Technical Manager,

SMMT

10:05 – 10:30 Explanation of 2007/46 EC Article 6 Procedures for the EC type-approval of vehicles.Step by step, single step and mixed type- approval. Option available using the Vehicle information folders in 2007/46/EC Annex 1 or Annex III part 11

Mike Protheroe, Vehicle Certification Agency (VCA).

10:30 – 10:50 SENTA Overview Tony Hopkins, Technical Manager,SMMT

10:50 – 11:15 Worked example of an ECWVTA for a Category N3 HCV Mike Protheroe, Vehicle Certification Agency (VCA).

11:15 – 12:00 Questions


The current situation

To register a Commercial vehicle of Categories N1, 2 & 3 –

National Type Approval

Covers 7 areas of the vehicle –

Brakes

Emissions

Noise

Smoke

Front underrun (if applicable)

Tyres

Speed limiter (if applicable)


Vehicle categories

• Category N1:

Vehicles designed and constructed for the carriage of goods and having a maximum mass not exceeding 3,5 tonnes.

• Category N2:

Vehicles designed and constructed for the carriage of goods and having a maximum mass exceeding 3,5 tonnes but not exceeding 12 tonnes.

• Category N3:

Vehicles designed and constructed for the carriage of goods and having a maximum mass exceeding 12 tonnes.


So what's changing?

For all categories of Commercial Vehicle –

European Community Whole Vehicle Type Approval

EC Directive 2007/46/EC


2007/46/EC

342 Pages

21 Annex’s

Covers all vehicle categories and types

Anything up to 60+ separate directives to comply with


Type approval routes

• European Community Whole Vehicle type Approval (ECWVTA).

Full approval to register unlimited numbers of a type of vehicle within the EU

• National Small series Type Approval (NSSTA).

Approval to register a limited number of a type of vehicle within the member state issuing the approval

• Individual Vehicle Approval (IVA).

Approval of a single type of vehicle. Administered by VOSA.


Conformity of production (COP)

As part of the approval process for ECWVTA and

NSSTA, you will require a COP process.

• ECWVTA – Formal process

• NSSTA – An ‘approved’ process

Both ECWVTA & NSSTA will require control plans. Further

information can be obtained from the Vehicle Certification Agency

(VCA).

• IVA - No COP required


Directives and regulations on motor vehicles, their trailers, systems and components

• Commission Decision of 14 July 2011 correcting Directive 2010/19/EU as regards the amendment of the Annexes to Directive 2007/46/EC

• Commission Regulation (EU) No 678/2011 of 14 July 2011 replacing Annex II and amending Annexes IV, IX and XI to Directive 2007/46/EC of the European Parliament and of the Council (Framework Directive)

• Commission Regulation (EU) No 566/2011 of 8 June 2011 amending Regulation (EC) No 715/2007 of the European Parliament and of the Council and Commission Regulation (EC) No 692/2008 as regards access to vehicle repair and maintenance information

• Commission Regulation (EU) No 582/2011 of 25 May 2011 implementing and amending Regulation (EC) No 595/2009 of the European Parliament and of the Council with respect to emissions from heavy duty vehicles (Euro VI) and amending Annexes I and III to Directive 2007/46/EC of the European Parliament and of the Council

• Commission Regulation (EU) No 183/2011 of 22 February 2011 amending Annexes IV and VI to Directive 2007/46/EC of the European Parliament and of the Council establishing a framework for the approval of motor vehicles and their trailers and of systems, components and separate technical units intended for such vehicles (Framework Directive)

http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:32011D0415:en:NOT

http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:32011R0678:en:NOT





Items to consider for the future

• General Safety Regulation (GSR) including AEBS

Repeals 50 directives and combines requirements into 1 regulation

Reduces need for testing and approval to EEC requirements as UN ECE Regulations Approvals accepted where available

Start to be phased in from 1st November 2012


• Masses and Dimensions

• TCMV Sub-Group on European Community Small Series Type Approval (ECSSTA) M1 and N1

• European Small Series Approval


• AEBS.

Published in the OJ on the 16 April 2012 as 347/2012

• Other items discussed at the TCMV of 16 April 2012

included:

Masses and Dimensions

Amendments to Annex IV and XII (2007/46)


Nationally:

• Revisions have been published to the VOSA IVA Manuals for N2/3 and M2/3

• Brake test requirements due to be published relating to IVA testing of trailers


The Directive 2007/46/EC became law on the 29 April 2009. The key dates from today are: New types of vehicles

29 October 2012

Existing typesof vehicles(Registrations)

29 April 2012 29 April 2013 29 October 2014

29 October 2012 29 October 2013

2012 2013 2014

Completed vehicles ofCategory N2, N3.

Special purpose vehiclesof category N1, N2, N3, M2, M3,O1, O2, O3, O4

M1 WAV’s, ambulancesand motor homes

Incomplete andcompleted vehiclesof categoriesN2, N3, O1, O2, O3, O4

Completed vehiclesof category N1

Completed vehicles ofcategory , O1, O2, O3, O4

Special purposevehicles of categoryN1, N2, N3, M2, M3,O1, O2, O3, O4

Completed vehiclesof category N2, N3


Summary

• Automotive legislation is continually moving and changing.

• What has been indicated here has been derived from

the SMMT and Members discussions and consultations at the UK, EC and Globally through the UNECE.

• The legislation is usually written to cover all categories of vehicles. It is one of the roles of the SMMT to filter out only those parts that are applicable to the vehicles that you manufacture. This is especially true of the SENTA guide which I will speak about further later.


Mike Protheroe, Standards and Legislation Manager VCA


SENTA

SMMT European and National Type Approval

guide


SENTA - SMMT European and National Type Approval guide A step-by-step web-based programme to guide vehicle manufacturers, bodybuilders and suppliers through the complicated European Community Whole Vehicle Type Approval system. It also allows for national approval schemes for low volume manufacturers.

For a new approval application, SENTA will ease the lengthy process.

SENTA details what a manufacturer must do from the original design idea, through the development and construction stages to completion of the approval process.


SENTA - SMMT European and National Type Approval guide

The guide is split into three parts.

Registered users will be guided through the ECWVTA process from start to finish. This will be based on their specific requirements and supported by:


SENTA - SMMT European and National Type Approval guide

The guide simplifies the approval process for those dealing with multi-stage builds by requesting specific information. Help information and worked examples are available for each section of the guide.


First Page


Section 1 – Start of page

Special purpose vehicle

category added


Section 1 – Page continuation


Section 1 – End of page


Section 2 – Start of page


Section 1 flag increased in size for clarity - Application for a Body Builder or Converter

If you are a Body Builder or Converter, please only complete Section 1 and 2 and then go to Section 9. Download and save a copy of the completed Annex I or Annex III Document. Complete the Appendix I - Multi-Stage Build base vehicle summary found at the end of the document. This can be used as part of your Approval application. Dependant on the data listed, you may need to return to Sections 3 to 8 to enter any relevant data there, if necessary.


103950 Appendix 1 – Multi Stage build vehicle summary

•Stage 1:

•Make or Trade name of manufacturer: e.g SENTA Trucks

•Model or Commercial name: e.g Atago •Type: AT001 •ECWVTA Number: e#*2007/46*####*## of the incomplete/complete vehicle •Stage 2:

•Subjects approved in second stage for the completed vehicle •Lateral Protection – e11*?? •Rear underrun device - e11*?? •Rear registration plate space - e11*?? •Lighting Installation - e11*?? •Spray Suppression – e11*?? •Additional subjects approved:

•Statutory Plates - e11*?? •Masses and dimensions - e11*??

See Section 1 flag note


Sections 3 to 8

Further vehicle information where applicable


Section 10 list of reference documents

Section 11 General Type Approval Reference documents


Section 11 General Type Approval Reference documents

Item Subject Regulatory act reference N2 EC WV TA

UNECE Regulation number

Series of amendments Type Approval applicant information document

required

1Sound levels vehicle 70/157/EEC X 51 02

2 Emissions 70/220/EEC X

2a Emissions (Euro 5 and 6) light duty vehicles/ access to information

715/2007/EC X(9)

3a Fuel tanks/rear protective devices – fuel tanks

70/221/EEC X(5)

34 02

3b Fuel tanks/rear protective devices – vehicle rear underrun

70/221/EEC X(5)

3c Fuel tanks/rear protective devices – STU rear underrun

70/221/EEC X(5)

3d LPG tanks X 67 01

3e CNG tanks X 110 00

3f Rear protective device X 58 01

4 Rear registration plate space 70/222/EEC X - -

5 Steering effort 70/311/EEC X 79 01

6 Door latches and hinges 70/387/EEC X 11 02

7a Audible warning component 70/388/EEC X 28 02


INFORMATION DOCUMENT FOR 77/839 TOWING HOOKS

APPENDIX 1 INFORMATION DOCUMENT No ........

Pursuant to Annex I of Council Directive 70/156/EEC relating to EC Type-Approval of a vehicle with respect to the towing-devices

(Directive 77/389/EEC, as last amended by Directive .../...) The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4

format. Photographs, if any, must show sufficient detail. 0. General 0.1. Make (trade name of manufacturer): Alba 0.2. Type and general commercial description(s): BB 0.3. Means of identification of type, if marked on the vehicle (b): VIN 0.3.1. Location of that marking: Cab 0.4. Category of vehicle (c): N3 0.5. Name and address of manufacturer: Alba

Holm Industrial Estate Worthing BN13 2AB

0.8. Address(es) of assembly plant(s): As above 1. General construction characteristics of the vehicle 1.1. Photographs and/or drawings of a representative vehicle: See Annex 1.1

Start of page – note: data automatically entered from input to previous sections. This will happen to any information document saved


Sections 13 – Type, Variant and Version chart


Sections 14 – Approval list


Section 15 – Certificates of conformity


MODEL B – SIDE 1 ECWVTA COMPLETED VEHICLES

EC CERTIFICATE OF CONFORMITY Side 1 The undersigned ………………………………………………………..(Full name and position) hereby certifies that the vehicle: 0.1Make (Trade name of the manufacturer): …………………………………………………. 0.2: Type: …………………………………………………………………………………………………………. Variant(a):………………………………………………………………………………………………….. Version(a) ……………………………………………………………………………………………………….. 0.2.1 Commercial name: ………………………………………………………………………………………… 0.4 Vehicle category: …………………………………………………………………………………………… 0.5: Name and address of the manufacturer: ……………………………………………………… 0.6 Location and method of attachment of the statutory plates: ……………………… Location of the vehicle identification number: ……………………………………….. 0.9 Name and address of the manufacturer’s representative (if any): ………………………………………………………………………………………………………………………… 0.10 Vehicle identification number: …………………………………………..………………………………….. a) has been completed and altered(1) as follows: ………………………………………and b) conforms in all respects to the type described in approval (…type-approval number including extension number) issued on (…date of issue) and c) can be permanently registered in Member States having right/left (b) hand traffic and using metric/imperial(c) units for the speedometer(d) …………………………………………… ........................................................ (Place)(Date) (Signature) Attachments: Certificate of conformity delivered at each previous stage.

Side 1 of the CoC


Take a Tour guideline information

The Tour is a snapshot of what is contained in the SENTA Guide which is written to cover all categories of vehicles and the possible Approval Routes. It gives an indication of how the Guide works by showing parts of the Section pages and how they may be used.

The application and compliance data included in the Tour is based on a European Approval for a large Truck built in two stages – ECWVTA N3 MSB


SENTA information and registration

Go to SMMT website, smmt.co.uk, front page and click on the SENTA button in the top right hand corner


Mike Protheroe, Standards and Legislation Manager VCA


Q&A session


Thank you for attending

Society of Motor Manufacturers and Traders Ltd

71 Great Peter Street, London, SW1P 2BN

www.smmt.co.uk

SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the...

Documents

Transcript of SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the...