sm_civil
-
Upload
muthu-praveen-sarwan -
Category
Documents
-
view
219 -
download
0
Transcript of sm_civil
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 1/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 1
Department of Civil Engineering
Subject Name: Strength of Materials Lab Subject Code: CE 2252
1. BRINELL’S HARDNESS TEST
AIM
To determine the hardness number of various specimens like steel, cast iron aluminium brass.
APPARATUS REQUIRED
1. Berinell’s hardness test2. Ball indicator
3. Traveling microscope
FORMULAThe surface area of indentation
A = πD/2 * (D-√(D²-d²))
Where,D = Diameter of BallD = the mean diameter of indentation
The Brinells hardness number= test load/surface area of indentation
= P/A
PROCEDURE:1. Based on the following table, the proper load and ball was selected to suit material in test. The
surface of the specimen is brushed and well cleaned.2. The selected ball is inserted in the machine and specimen load is determined.3. Now the load is released.4. The diameter of indentation is measured.
RESULT:
BHN FOR “A1” SAMPLE=
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 2/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 2
S.NO MATERIAL LOAD DIA OFINTENTATIONIN mm
SURFACEAREA OFINTENTATIONIN mm
BHN
ALUMINIUM
BRASS
STEEL
CAST IRON
OBSERVATION
Material of test piece:
Type of penetrator:
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 3/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 3
2. TORSION TEST
AIM:
To determine the modulus of rigidity of the sample of given rod.
APPARATUS REQUIRED1. Torsion testing machine2. Test specimen3. Steel rule4. Caliper
FORMULATorsional equation T/J = Cθ /L
Modulus of rigidity C = TL/Jθ
WhereT= Torsional moment in N-mmL= Length of test pullJ= Polar moment of inertiaθ= Angle of twist in radian
PROCEDURE:1. Using the micrometer the diameter ‘L’ of specimen is measured in four places.2. The length of ‘l’ of the specimen is measured accurately of seeing into the
machine.3. After selecting the suitable scale on the machine the initial and angle of twistwhere adjusted zero.
4. Up to angle of twist the torque was applied zero.5. There are the machine was separated electrically and readings at 10 intervals
where the reading is noted continuously unit specimen failed.
GRAPHThe angle of twist ,in degree values. Torque in N-m graph was drawn. Angle of twist in
x-axis and torque in y-axis.
RESULT1. The modulus of rigidity of sample (from tabulation) =2. The modulus of rigidity of sample (from graph) =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 4/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 4
S.NO APPLIEDTORQUE
ANGLE OF TWIST θ INRADIANS
MODULUSOF RIGIDITYIN N- MM²KG-
CMN-MM
DEGREE OF FREEDOM
θ1 θ 2 θ AVERAGE
OBSERVATION:
Material of test piece =Length of the specimen =
Diameter of the specimen =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 5/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 5
3.TEMPERING
AIM:
To perform the heat treatment tempering on the given material C-40 steel.
APPARATUS REQUIRED:1. Muffle furnace: tongs2. Given material: C-40 steel3. Quenching medium: water
PROCEDURE:
1. The given specimen is subjected to Rockwell hardness test and Rockwellhardness number is measured before hardening that the specimen issubjected to rough grinding.
2. The specimen is placed inside the combustion chamber of muffle furnaceand is heated up to 630˚ C.
3. Then the specimen is soaked for 10 minutes at the same temperature630˚C.4. After soaking it is taken out from the furnace and it is cooled in air.5. The specimen is cooled, now the tempering is completed.6. Again the specimen is subjected to Rockwell hardness test and Rockwell
hardness number is measured.
RESULT:
The heat treatment tempering on the given material C-40 steel and its Rockwell hardness numberis measured
Rockwell hardness number before tempering =Rockwell hardness number after tempering =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 6/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 6
S.NO SPECIMENMATERIAL
LOAD
N
PENETRATOR SCALE RHN MEANRHN
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 7/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 7
4. HARDENING
AIM:
To perform the heat treatment on the given material C-40 steel.
APPARATUS REQUIRED:1. Muffle furnace: tongs2. Given material: C-403. Quenching material: water
PROCEDURE:
1.The given specimen is subjected to Rockwell hardness test andRockwell hardness number is measured before hardening.
2.The specimen is placed inside the combustion chamber of mufflefurnace and is heated up to 830˚ C.
3.Then the specimen is socked for 10 minutes at the same temperature
830˚C.4.After socking it is taken out from the furnace and it is quenched in thewater.
5.The specimen is cooled, now the hardening is completed.6.Again the specimen is subjected to Rockwell hardness test and Rockwell
hardness number is measured.
RESULT:
The heat treatment hardening on the given material C-40 steel and its Rockwell hardness numberis measured
Rockwell hardness number before tempering =Rockwell hardness number after tempering =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 8/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 8
S.NO SPECIMEN
MATERIAL
LOAD
N
PENETRATOR SCALE RHN MEAN
RHN
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 9/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 9
5. ROCKWELL HARDNESS TEST
AIM:
To determine Rockwell hardness number for steel aluminium, copper, brass, and alloy.
APPARATUS REQUIRED:
1.Rockwell hardness tester.2.120˚ diamond cone penetrator3.1/16 diamond steel4.specimen
PROCEDURE:
1.The test piece was cleaned and placed on the special anvil of the machine.2.The capstan wheel was turned to elevate the test specimen to contact the indenter point.
3.The wheel was further turned to face the test specimen against the indenter. This will ensurethat a minor load has been applied on the specimen.4.The pointer was set on to appropriate scale; the dial gauge was set in appropriate position
based on the scale used.5.The lever was pushed forward and the major load was applied.6.As soon as the pointer in the dial goes to rest, release the lever which will release the major
load. The pointer will rotate in the reverse direction.7.The Rockwell hardness is used on the appropriate scale dial.
RESULT:
The Rockwell hardness number forAluminium sample =Copper sample =Steel sample =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 10/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 10
S.NO SPECIMENMATERIAL
LOAD
N
PENETRATOR SCALE RHN MEANRHN
OBSERVATION:Material of test piece =
Type of penetrator =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 11/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 11
6.IMPACT TEST (CHARPY)
AIM:
To determine the impact of the material using Charpy’s glove.
APPARATUS REQUIRED:
1.impact testing machine.2.test specimen.3.scale.4.caliper.
FORMULA: Impact strength = Energy required to break the specimen
Area of cross section of notch point
PROCEDURE:1.The striker was screwed firmly to the center of the hammer.2.The hammer was screwed freely to note down the energy loss due to friction.3.The test specimen was fixed on support with the notch.4.The pointer scale was read.5.The striker was released by operating a lever and the specimen was broken.6.The pendulum was brought to rest by applying brake.7.The pointer and the scale value were read. This is the energy required to break the specimen.8.The broken specimen and the striker are removed.
RESULT:Impact strength of the given material was found to be =……..J/mm².
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 12/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 12
S.NO LOSS OFENERGY DUE
TO FRICTION
Jm
ENERGYREQUIRED
BREAK THESPECIMEN
Jm
ACTUALENERGY
REQUIRED
Jm
IMPACTSTRENGTH
Jm
OBSERVATION:
Dimension of test piece =Type of notch =Angle of notch =Depth of notch =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 13/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 13
7. IMPACT TEST (IZOD’S)
AIM: To determine the impact of the material using Izod’s glove.
APPARATUS REQUIRED:1. Impact testing machine.2. Test specimen.3. Izod’s machine.4. Izod’s accessories.5. Caliper.
FORMULA:
Impact strength = Energy required to break the specimen
Area of cross section of notch point
PROCEDURE:
1.The striker was screwed firmly to the center of the percussion of the hammer with screws.2.The hammer was swing freely to note down the energy loss due to friction.3.The test specimen was fixed on support with the notch facing the striking direction and the
clamp screw are tightened.4.The pointer scale was read.5.The striker is released by operating a lever and the specimen was broken.6.The pendulum was brought to rest by applying brake.7.The pointer and the scale value were read. This is the energy required to break the specimen.8.The broken specimen and the striker are removed.
RESULT:Impact strength of the given material was found to be =……..J/mm².
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 14/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 14
S.NO LOSS OF
ENERGY DUETO FRICTION
Jm
ENERGY
REQUIREDBREAK THESPECIMEN
Jm
ACTUAL
ENERGYREQUIRED
Jm
IMPACT
STRENGTH
Jm
OBSERVATION:Dimension of test piece =Type of notch =Angle of notch =Depth of notch =Distance of notch from one end =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 15/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 15
8. VERIFICATION OF MAXWELL’S RECIPROCAL THEOREM
AIM:
To verify the Maxwell’s reciprocal theorem.
APPARATUS:1. Beam to be tested2. Roller supports3. Set of weight of hanger4. Deflectometer5. Vernier caliper6. Scale
PROCEDURE:
1. Place the given beam over the supports of measure the span of the beam.2. Place the hanger ¼ span from right hand side.3. Note the deflectometer reading at no load position.4. Load the beam at uniform rate of note down the corresponding
deflectometer reading.5. Decrement the load at the same uniform rate and down the corresponding
deflectometer reading.6. Now place the deflectometer at ¼ of span from left hand side and place
hanger at ¼ of span from right hand side and repeat the steps 4 and 6.
RESULT:Deflection of beam from load at A and deflection for at B E =Deflection of beam from load at B and deflection for at A E =Therefore Maxwell’s reciprocal theorem is verified.
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 16/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 16
DEFLECTION AT “A” AND LOAD AT “B”
S.NO LOAD DEFLECTOMETER READING IN mm DEFLECTIONAT “A” INmm * L.C
YOUNG’SMODULUSIN N/mm²LOADING UNLOADING MEAN
DEFLECTION
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 17/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 17
DEFLECTION AT “B” AND LOAD AT “A”
S.NO LOAD DEFLECTOMETER READING IN mm DEFLECTIONAT “B” INmm * L.C
YOUNG’SMODULUSIN N/mm²
LOADING UNLOADING MEANDEFLECTION
OBSERVATION:1. Length of simply supported beam =2. Breadth of simply supported beam =3. Depth of simply supported beam =4. Position of load from left support =5. Position of load from right support =6. Position of deflectometer =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 18/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 18
9. DEFLECTION TEST ON BEAMS (simply supported)
Aim: To determine the young’s modulus of the given beam material.
APPARATUS:1. Beam to be rested2. Roller supports3. Weight with hangs4. Deflectometer5. Calipers6. Measuring scale
FORMULA:The general expression for deflection of any point ‘x’ is given by
∆ = wbx(l²-b²-x²) for x<a where l = a+b
6EIl
I = moment of Inertia = Bd³/12 (mm^4)∆ = deflection (mm)B = breadth of simply supported beam (mm)
l = length of simply supported beam (mm)x = position of deflectometerb = position of loadw = load
PROCEDURE:
1. The breadth ‘B’ and depth ‘d’ of beam where measured accurately.2. The supports are arranged to the required span and the beam is placed over the supports.3. The loading point was marked and the distance ‘y’ from left support.4. The deflectometer reading was noted down at no reading condition.5. The beam was loading at uniform rate and corresponding deflectometer readings were
noted.6. Deflection vs. load graph was drawn and young’s modulus of beam material was found
out.
Graph:
A graph draw by taking load in the y-axis and deflection in the ‘x’ axis.
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 19/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 19
Result:The young’s modulus of the beam material is found to be for steel from tabulations E =
From graph E =
S.NO LOAD DEFLECTOMETER READING IN mm DEFLECTIONAT “b” IN mm* L.C
YOUNG’SMODULUSIN N/mm²
LOADING UNLOADING MEANDEFLECTION
OBSERVATION:1. Span of simply supported beam =2. Distance of load system from left support =3. Breadth of beam =4. Depth of beam =5. Distance of deflection from left support =6. Least count of deflectometer =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 20/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 20
10.COMPRESSION TEST ON HELICAL SPRING (Open coiled)
AIM:
1. To determine the rigidity modulus of the spring.
2. To find the stiffness of the spring.3. To determine the energy absorbed by the spring for a particular load.
APPARATUS REQUIRED:1.Open coiled helical spring2. Spring testing machining.3. Caliper etc.
FORMULA USED:
1. The mean radius of the spring is touch using the inner and outer diameter of spring.
R = (Do+Di )/4WhereDo = outer diameter of springDi = inner diameter of spring.
2.The angle of helix
α = tan-1 (pitch/2 π R)Average pitch = [total height spring/No. of turns]
3.The rigidity modulus of the material is found from the mean deflection using the following
∆ = 64WR3N secα Cos²α + 2sin²α d^4 C E
4. The stiffness of the spring is given byS = W/D * N/mm
5. The energy is started for particular load is given by
U = ½ WD N-mm
PROCEDURE:1.The inner and outer diameter of the spring was measured.2. The diameter of the coil was measured.3. The number of turns and the angle of helix counted.
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 21/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 21
4. The spring was loaded at uniform rate and the corresponding scalereading was noted at every step
5.The scale was placed between the places at reading unit.
6. The load was released at the same step and the scale readings are noted.
GRAPH:The graph was drawn taking mean deflection in x-axis level in y-axis.
RESULT:
1.Thestiffnes of the given spring is =2. The rigidity modulus of the spring =3. The energy started in the spring for a load of …..N =
From graph
The load of …..N from graph=
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 22/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 22
MEAN=
OBSERVATIONOuter dia of the spring =Inner dia of the spring =Young’s modulus =
Dia of the coil wire =Length of the spring =No. of turns =
S.NO LOAD VERTICAL SCALE READING DEFLECTIONIN mm
STIFFNESSIN N/mm²
RIGIDITYMODULUSIN N/mm²
INITIAL FINAL DEFLECTION
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 23/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 23
11. TENSION TEST ON HELICAL SPRING (Closed coil)
AIM:
1. To determine the rigidity modulus of the spring material.2. To find the stiffness of the spring.3. To determine the energy started in the spring at particular load.
APPARATUS REQUIRD:1. Closed coiled helical spring2. Spring testing machine3. Caliper’s etc.
FORMULA:Rigidity modulus P = 64WR³N∆ d^4
W = load in NN = No. of turns∆ = deflection in mmD = diameter of coil wire in mm
Stiffness of the spring = W/ ∆ N /mm²Strain energy rated = W*∆ /2 N/mm²
PROCEDURE:1. The inner and outer diameters of the spring were measured.2. The diameter of coil was measured.3. The number of turns of before curve was counted.4. The spring was placed between the plates of the loading unit.5. The initial scale reading was noted.6. The load was applied at an uniform7. The scale readings were noted for regular interval of increased a load.8. Then the released at same point steps and scale readings were noted.
GRAPH:The mean value of deflection was plotted on x- axis and load was plotted on y- axis.
RESULT:1.Strain energy stored in the spring =2.Rigidity modulus of the spring =3.Stiffness of the spring =4.By graph =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 24/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 24
MEAN=
OBSERVATION
Outer dia of the spring =Inner dia of the spring =
Young’s modulus =Dia of the coil wire =Length of the spring =No. of turns =
S.NO LOAD VERTICAL SCALE READING DEFLECTIONIN mm
STIFFNESSIN N/mm²
RIGIDITYMODULUSIN N/mm²INITIAL FINAL DEFLECTION
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 25/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 25
12.TENSION TEST ON MILD STEEL ROD
AIM
1. To determine the yield stress of steel.
2. To determine the ultimate stress of steel.3. To determine the breaking stress of steel.4. To determine the reduction in area in steel.5. To determine the percentage of elongation of steel.6. To determine the elasticity modulus of steel.
APPARATUS REQUIRED
1. Universal testing machine.2. Extensometer.3. Scale.4. Vernier caliper etc..,
PROCEDURE1. Accurately measure the diameter of given rod.2. Mark the gauge length to determine the elongation.3. Assuming the ultimate stress of the material, choose the load range in UTM for
the given steel bar the ultimate Stress may be assumed as 500N/mm² and therequired Ultimate load can be calculated.
4. Fix the test specimen between the steel grips of the UTM taking care to see thatthe load will be applied axially and fix the extensometer.
5. Apply the load gradually and in uniform steps and note down the correspondingextensometer reading.
6. Remove the extensometer after 70% of the yield load is applied .Yield load may
be calculated by product of projected yield stress (250N/mm² in case of steel)and the area of cross section.7. Note down the load at yield i.e., the short deviation of time when the pointer
remains stationary.8. Increase the load and note down the ultimate load. At the ultimate load the red
pointer will be left in position and the black point which indicate theinstantaneous applied load will move in to reverse direction.
9. Note down the break point load at which the specimen fails.10. Remove the specimen and note down the diameter of the neck and the elongation.
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 26/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 26
RESULT
1. The yield stress of material = N/mm²
2. The ultimate stress of material = N/mm²
3. The breaking stress of material = N/mm²
4. Percentage of elongation of material = %
5. Percentage of reduction of cross section area = %
OBSERVATION:
Specimen load =
Diameter of specimen = mm
Area of specimen =
Gauge length =
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 27/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
CHENNAI INSTITUTE OF TECHNOLOGY Page 27
13. DOUBLE SHEAR TEST
AIM
To determine the ultimate shear strength of the material by conducting a double shear test.
APPARATUS USED1. Universal testing machine2. Shear test attachment.3. Calipers etc.,
FORMULA
Cross sectional area of the specimen = π /4 * d²Ultimate shear strength = Failure load/ 2π /4 *d²
PROCEDURE1. By using calipers, measure the diameter of specimen.2. The specimens were inserted in shearing apparatus and tightly screwed3. This assembly is kept between the plates of the compression zone of the UTM4. The load was applied gradually and the failure load was noted.5. This experiment was repeated for more specimens.
RESULT
The Ultimate shear strength of the given material = N/mm²
8/3/2019 sm_civil
http://slidepdf.com/reader/full/smcivil 28/28
CHENNAI INSTITUTE OF TECHNOLOGY
Sarathy Nagar, Kundrathur, Pudupedu, Chennai– 600 069.
S.NO TYPE OF
MATERIAL
LOAD OF FAILURE (N) ULTIMATE SHEAR
STRENGTH N/mm²
OBSERVATION
Material of test piece =Length of specimen =Diameter of specimen =