PBSS4230PAN - Nexperia · 2017. 5. 29. · PBSS4230PAN BoAmodPE9(4(RLfc(nlldPNCa)do)odwot Nexperia...

PBSS4230PAN30 V, 2 A NPN/NPN low VCEsat (BISS) transistor14 December 2012 Product data sheet

1. General descriptionNPN/NPN low VCEsat Breakthrough In Small Signal (BISS) transistor in a leadlessmedium power DFN2020-6 (SOT1118) Surface-Mounted Device (SMD) plastic package.

NPN/PNP complement: PBSS4230PANP. PNP/PNP complement: PBSS5230PAP.

2. Features and benefits• Very low collector-emitter saturation voltage VCEsat• High collector current capability IC and ICM• High collector current gain hFE at high IC• Reduced Printed-Circuit Board (PCB) requirements• High efficiency due to less heat generation• AEC-Q101 qualified

3. Applications• Load switch• Battery-driven devices• Power management• Charging circuits• Power switches (e.g. motors, fans)

4. Quick reference dataTable 1. Quick reference dataSymbol Parameter Conditions Min Typ Max Unit

Per transistor

VCEO collector-emittervoltage

open base - - 30 V

IC collector current - - 2 A

ICM peak collector current single pulse; tp ≤ 1 ms - - 3 A

Per transistor

RCEsat collector-emittersaturation resistance

IC = 1 A; IB = 0.1 A; pulsed; tp ≤ 300 µs;δ ≤ 0.02 ; Tamb = 25 °C

- - 145 mΩ

© Nexperia B.V. 2017. All rights reserved

Nexperia PBSS4230PAN30 V, 2 A NPN/NPN low VCEsat (BISS) transistor

PBSS4230PAN All information provided in this document is subject to legal disclaimers.

Product data sheet 14 December 2012 2 / 17

5. Pinning informationTable 2. Pinning informationPin Symbol Description Simplified outline Graphic symbol

1 E1 emitter TR1

2 B1 base TR1

3 C2 collector TR2

4 E2 emitter TR2

5 B2 base TR2

6 C1 collector TR1

7 C1 collector TR1

8 C2 collector TR2

Transparent top view

6

7 8

5 4

1 2 3

DFN2020-6 (SOT1118)sym140

B1E1 C2

B2C1

TR1TR2

E2

6. Ordering informationTable 3. Ordering information

PackageType number

Name Description Version

PBSS4230PAN DFN2020-6 plastic thermal enhanced ultra thin small outline package; noleads; 6 terminals; body 2 x 2 x 0.65 mm

SOT1118

7. MarkingTable 4. Marking codesType number Marking code

PBSS4230PAN 2G

8. Limiting valuesTable 5. Limiting valuesIn accordance with the Absolute Maximum Rating System (IEC 60134).Symbol Parameter Conditions Min Max Unit

Per transistor

VCBO collector-base voltage open emitter - 30 V

VCEO collector-emitter voltage open base - 30 V

VEBO emitter-base voltage open collector - 7 V

IC collector current - 2 A

ICM peak collector current single pulse; tp ≤ 1 ms - 3 A

IB base current - 0.3 A





Symbol Parameter Conditions Min Max Unit

IBM peak base current single pulse; tp ≤ 1 ms - 1 A

[1] - 370 mW

[2] - 570 mW

[3] - 530 mW

[4] - 700 mW

[5] - 450 mW

[6] - 760 mW

[7] - 700 mW

Ptot total power dissipation Tamb ≤ 25 °C

[8] - 1450 mW

Per device

[1] - 510 mW

[2] - 780 mW

[3] - 730 mW

[4] - 960 mW

[5] - 620 mW

[6] - 1040 mW

[7] - 960 mW

Ptot total power dissipation Tamb ≤ 25 °C

[8] - 2000 mW

Tj junction temperature - 150 °C

Tamb ambient temperature -55 150 °C

Tstg storage temperature -65 150 °C

[1] Device mounted on an FR4 PCB, single-sided 35 µm copper strip line, tin-plated and standard footprint.[2] Device mounted on an FR4 PCB, single-sided 35 µm copper strip line, tin-plated, mounting pad for

collector 1 cm2.[3] Device mounted on 4-layer PCB 35 µm copper strip line, tin-plated and standard footprint.[4] Device mounted on 4-layer PCB 35 µm copper strip line, tin-plated, mounting pad for collector 1 cm2.[5] Device mounted on an FR4 PCB, single-sided 70 µm copper strip line, tin-plated and standard footprint.[6] Device mounted on an FR4 PCB, single-sided 70 µm copper strip line, tin-plated, mounting pad for

collector 1 cm2.[7] Device mounted on 4-layer PCB 70 µm copper strip line, tin-plated and standard footprint.[8] Device mounted on 4-layer PCB 70 µm copper strip line, tin-plated, mounting pad for collector 1 cm2.





Tamb (°C)-75 17512525 75-25

006aad165

0.5

1.0

1.5

Ptot(W)

0

(1)

(2)(3) (4)(5)(6)(7)(8)

(1) 4-layer PCB 70 µm, mounting pad for collector 1 cm2

(2) FR4 PCB 70 µm, mounting pad for collector 1 cm2

(3) 4-layer PCB 70 µm, standard footprint

(4) 4-layer PCB 35 µm, mounting pad for collector 1 cm2

(5) FR4 PCB 35 µm, mounting pad for collector 1 cm2

(6) 4-layer PCB 35 µm, standard footprint(7) FR4 PCB 70 µm, standard footprint(8) FR4 PCB 35 µm, standard footprint

Fig. 1. Per transistor: power derating curves

9. Thermal characteristicsTable 6. Thermal characteristicsSymbol Parameter Conditions Min Typ Max Unit

Per transistor

[1] - - 338 K/W

[2] - - 219 K/W

[3] - - 236 K/W

[4] - - 179 K/W

[5] - - 278 K/W

[6] - - 164 K/W

[7] - - 179 K/W

Rth(j-a) thermal resistancefrom junction toambient

in free air

[8] - - 86 K/W

Rth(j-sp) thermal resistancefrom junction to solderpoint

- - 30 K/W





Symbol Parameter Conditions Min Typ Max Unit

Per device

[1] - - 245 K/W

[2] - - 160 K/W

[3] - - 171 K/W

[4] - - 130 K/W

[5] - - 202 K/W

[6] - - 120 K/W

[7] - - 130 K/W

Rth(j-a) thermal resistancefrom junction toambient

in free air

[8] - - 63 K/W

[1] Device mounted on an FR4 PCB, single-sided 35 µm copper strip line, tin-plated and standard footprint.[2] Device mounted on an FR4 PCB, single-sided 35 µm copper strip line, tin-plated, mounting pad for

collector 1 cm2.[3] Device mounted on 4-layer PCB 35 µm copper strip line, tin-plated and standard footprint.[4] Device mounted on 4-layer PCB 35 µm copper strip line, tin-plated, mounting pad for collector 1 cm2.[5] Device mounted on an FR4 PCB, single-sided 70 µm copper strip line, tin-plated and standard footprint.[6] Device mounted on an FR4 PCB, single-sided 70 µm copper strip line, tin-plated, mounting pad for

collector 1 cm2.[7] Device mounted on 4-layer PCB 70 µm copper strip line, tin-plated and standard footprint.[8] Device mounted on 4-layer PCB 70 µm copper strip line, tin-plated, mounting pad for collector 1 cm2.

006aad166

10-5 1010-210-4 10210-1tp (s)

10-3 1031

102

10

103

Zth(j-a)(K/W)

1

duty cycle = 1

0.750.5

0.33

0.2

0.1

0.05

0.020.01

0

FR4 PCB 35 µm, standard footprint

Fig. 2. Per transistor: transient thermal impedance from junction to ambient as a function of pulse duration;typical values





006aad167

10-5 1010-210-4 10210-1tp (s)

10-3 1031

102

10

103

Zth(j-a)(K/W)

1

duty cycle = 1

0.750.5

0.33

0.2

0.1

0.05

0.020.01

0

FR4 PCB 35 µm, mounting pad for collector 1 cm2


006aad168

10-5 1010-210-4 10210-1tp (s)

10-3 1031

102

10

103

Zth(j-a)(K/W)

1

duty cycle = 1

0.750.5

0.330.2

0.1

0.05

0.020.01

0

4-layer PCB 35 µm, standard footprint






006aad169

10-5 1010-210-4 10210-1tp (s)

10-3 1031

102

10

103

Zth(j-a)(K/W)

1

duty cycle = 1

0.750.5

0.33

0.2

0.1

0.05

0.02

0.010

4-layer PCB 35 µm, mounting pad for collector 1 cm2


006aac610

10- 5 1010- 210- 4 10210- 1tp (s)

10- 3 1031

102

10

103

Zth(j-a)(K/W)

10

duty cycle = 1

0.010.02

0.05

0.1

0.20.33

0.50.75

FR4 PCB 70 µm, standard footprint






006aac611

10- 5 1010- 210- 4 10210- 1tp (s)

10- 3 1031

102

10

103

Zth(j-a)(K/W)

10

duty cycle = 1

0.01

0.02

0.050.1

0.20.33

0.50.75

FR4 PCB 70 µm, mounting pad for collector 1 cm2


006aad170

10-5 1010-210-4 10210-1tp (s)

10-3 1031

102

10

103

Zth(j-a)(K/W)

1

duty cycle = 1

0.750.5

0.330.2

0.10.05

0.02

0.010

4-layer PCB 70 µm, standard footprint






006aad171

10-5 1010-210-4 10210-1tp (s)

10-3 1031

10

102

Zth(j-a)(K/W)

1

duty cycle = 1

0.75

0.5

0.33

0.2

0.10.05

0.02 0.01

0

4-layer PCB 70 µm, mounting pad for collector 1 cm2


10. CharacteristicsTable 7. CharacteristicsSymbol Parameter Conditions Min Typ Max Unit

Per transistor

VCB = 24 V; IE = 0 A; Tamb = 25 °C - - 100 nAICBO collector-base cut-offcurrent VCB = 24 V; IE = 0 A; Tj = 150 °C - - 50 µA

IEBO emitter-base cut-offcurrent

VEB = 5 V; IC = 0 A; Tamb = 25 °C - - 100 nA

VCE = 2 V; IC = 100 mA; pulsed;tp ≤ 300 µs; δ ≤ 0.02 ; Tamb = 25 °C

250 380 -

VCE = 2 V; IC = 500 mA; pulsed;tp ≤ 300 µs; δ ≤ 0.02 ; Tamb = 25 °C

230 350 -

VCE = 2 V; IC = 1 A; pulsed; tp ≤ 300 µs;δ ≤ 0.02 ; Tamb = 25 °C

200 310 -

hFE DC current gain

VCE = 2 V; IC = 2 A; pulsed; tp ≤ 300 µs;δ ≤ 0.02 ; Tamb = 25 °C

150 230 -

IC = 500 mA; IB = 50 mA; Tamb = 25 °C - 60 80 mV

IC = 1 A; IB = 50 mA; pulsed;tp ≤ 300 µs; δ ≤ 0.02 ; Tamb = 25 °C

- 120 160 mV


- 230 300 mV

VCEsat collector-emittersaturation voltage


- 220 290 mV





Symbol Parameter Conditions Min Typ Max Unit

RCEsat collector-emittersaturation resistance

IC = 1 A; IB = 0.1 A; pulsed; tp ≤ 300 µs;δ ≤ 0.02 ; Tamb = 25 °C

- - 145 mΩ

IC = 500 mA; IB = 50 mA; Tamb = 25 °C - - 1 V


- - 1 V


- - 1.1 V

VBEsat base-emitter saturationvoltage


- - 1.2 V

VBEon base-emitter turn-onvoltage

VCE = 2 V; IC = 0.5 A; pulsed;tp ≤ 300 µs; δ ≤ 0.02 ; Tamb = 25 °C

- - 0.9 V

td delay time - 10 - ns

tr rise time - 50 - ns

ton turn-on time - 60 - ns

ts storage time - 310 - ns

tf fall time - 60 - ns

toff turn-off time

VCC = 12.5 V; IC = 1 A; IBon = 50 mA;IBoff = -50 mA; Tamb = 25 °C

- 370 - ns

fT transition frequency VCE = 10 V; IC = 50 mA; f = 100 MHz;Tamb = 25 °C

60 120 - MHz

Cc collector capacitance VCB = 10 V; IE = 0 A; ie = 0 A;f = 1 MHz; Tamb = 25 °C

- 13.5 18 pF





006aad188

200

400

600

hFE

0

IC (mA)10-1 1041031 10210

(1)

(2)

(3)

VCE = 2 V(1) Tamb = 100 °C(2) Tamb = 25 °C(3) Tamb = −55 °C

Fig. 10. DC current gain as a function of collectorcurrent; typical values

VCE (V)0 542 31

006aad189

1

2

3

IC(A)

0

IB = 15 mA 13.5 12 10.5

9

7.5

6

4.5

3

1.5

Tamb = 25 °C

Fig. 11. Collector current as a function of collector-emitter voltage; typical values

006aad190

0.4

0.8

1.2

VBE(V)

0

IC (mA)10-1 1041031 10210

(1)

(2)

(3)

VCE = 2 V(1) Tamb = −55 °C(2) Tamb = 25 °C(3) Tamb = 100 °C

Fig. 12. Base-emitter voltage as a function of collectorcurrent; typical values

006aad191

0.6

0.8

0.4

1.0

1.2VBEsat

(V)

0.2

IC (mA)10-1 1041031 10210

(1)

(2)

(3)

IC/IB = 20(1) Tamb = −55 °C(2) Tamb = 25 °C(3) Tamb= 100 °C

Fig. 13. Base-emitter saturation voltage as a function ofcollector current; typical values





006aad192

10-1

10-2

1

VCEsat(V)

10-3

IC (mA)10-1 1041031 10210

(1)

(2)

(3)

IC/IB = 20(1) Tamb = 100 °C(2) Tamb = 25 °C(3) Tamb = −55 °C

Fig. 14. Collector-emitter saturation voltage as afunction of collector current; typical values

006aad193

10-1

10-2

1

VCEsat(V)

10-3

IC (mA)10-1 1041031 10210

(1)

(2)

(3)

Tamb = 25 °C(1) IC/IB = 100(2) IC/IB = 50(3) IC/IB = 10

Fig. 15. Collector-emitter saturation voltage as afunction of collector current; typical values

IC (mA)10-1 1041031 10210

006aad194

1

10-1

102

10

103

RCEsat(Ω)

10-2

(1)(2)

(3)

IC/IB = 20(1) Tamb = 100 °C(2) Tamb = 25 °C(3) Tamb = −55 °C

Fig. 16. Collector-emitter saturation resistance as afunction of collector current; typical values

IC (mA)10-1 1041031 10210

006aad195

1

10-1

102

10

103

RCEsat(Ω)

10-2

(1)

(2)

(3)

Tamb = 25 °C(1) IC/IB = 100(2) IC/IB = 50(3) IC/IB = 10

Fig. 17. Collector-emitter saturation resistance as afunction of collector current; typical values





11. Test information

006aaa003

IBon (100 %)

IB

input pulse(idealized waveform)

IBoff

90 %

10 %

IC (100 %)

IC

tdton

90 %

10 %

tr

output pulse(idealized waveform)

tf

t

tstoff

Fig. 18. BISS transistor switching time definition

RC

R2

R1

DUT

mlb826

Vo

RB(probe)450 Ω

(probe)450 Ω

oscilloscope oscilloscope

VBB

VI

VCC

Fig. 19. Test circuit for switching times

11.1 Quality informationThis product has been qualified in accordance with the Automotive Electronics Council(AEC) standard Q101 - Stress test qualification for discrete semiconductors, and issuitable for use in automotive applications.





12. Package outline

10-05-31Dimensions in mm

0.04max

0.65max

0.770.57(2×)0.540.44(2×)

2.11.9

2.11.9

1.10.9

0.30.2

0.65(4×)

0.350.25(6×)

43

1 6

Fig. 20. Package outline DFN2020-6 (SOT1118)

13. Soldering

sot1118_fr

Dimensions in mm

solder paste

solder resist

occupied area

solder lands

0.49 0.49

0.650.65

0.875

0.875

2.25

0.35(6×)

0.3(6×)

0.4(6×)

0.45(6×)

0.72(2×)0.82(2×)

1.05(2×)

1.15(2×)

2.1

Fig. 21. Reflow soldering footprint for DFN2020-6 (SOT1118)

14. Revision historyTable 8. Revision historyData sheet ID Release date Data sheet status Change notice Supersedes

PBSS4230PAN v.1 20121214 Product data sheet - -





15. Legal information

15.1 Data sheet statusDocumentstatus [1][2]

Productstatus [3]

Definition

Objective[short] datasheet

Development This document contains data fromthe objective specification for productdevelopment.

Preliminary[short] datasheet

Qualification This document contains data from thepreliminary specification.

Product[short] datasheet

Production This document contains the productspecification.

[1] Please consult the most recently issued document before initiating orcompleting a design.

[2] The term 'short data sheet' is explained in section "Definitions".[3] The product status of device(s) described in this document may have

changed since this document was published and may differ in case ofmultiple devices. The latest product status information is available onthe Internet at URL http://www.nexperia.com.

15.2 DefinitionsPreview — The document is a preview version only. The document is stillsubject to formal approval, which may result in modifications or additions.Nexperia does not give any representations or warranties as tothe accuracy or completeness of information included herein and shall haveno liability for the consequences of use of such information.

Draft — The document is a draft version only. The content is still underinternal review and subject to formal approval, which may result inmodifications or additions. Nexperia does not give anyrepresentations or warranties as to the accuracy or completeness ofinformation included herein and shall have no liability for the consequencesof use of such information.

Short data sheet — A short data sheet is an extract from a full data sheetwith the same product type number(s) and title. A short data sheet isintended for quick reference only and should not be relied upon to containdetailed and full information. For detailed and full information see therelevant full data sheet, which is available on request via the local Nexperiasales office. In case of any inconsistency or conflict with theshort data sheet, the full data sheet shall prevail.

Product specification — The information and data provided in a Productdata sheet shall define the specification of the product as agreed betweenNexperia and its customer, unless Nexperia andcustomer have explicitly agreed otherwise in writing. In no event however,shall an agreement be valid in which the Nexperia productis deemed to offer functions and qualities beyond those described in theProduct data sheet.

15.3 DisclaimersLimited warranty and liability — Information in this document is believedto be accurate and reliable. However, Nexperia does not giveany representations or warranties, expressed or implied, as to the accuracyor completeness of such information and shall have no liability for theconsequences of use of such information. Nexperia takes noresponsibility for the content in this document if provided by an informationsource outside of Nexperia.

In no event shall Nexperia be liable for any indirect, incidental,punitive, special or consequential damages (including - without limitation -lost profits, lost savings, business interruption, costs related to the removalor replacement of any products or rework charges) whether or not suchdamages are based on tort (including negligence), warranty, breach ofcontract or any other legal theory.

Notwithstanding any damages that customer might incur for any reasonwhatsoever, Nexperia’s aggregate and cumulative liability towardscustomer for the products described herein shall be limited in accordancewith the Terms and conditions of commercial sale of Nexperia.

Right to make changes — Nexperia reserves the right tomake changes to information published in this document, including withoutlimitation specifications and product descriptions, at any time and withoutnotice. This document supersedes and replaces all information supplied priorto the publication hereof.

Suitability for use in automotive applications — This Nexperiaproduct has been qualified for use in automotiveapplications. Unless otherwise agreed in writing, the product is not designed,authorized or warranted to be suitable for use in life support, life-critical orsafety-critical systems or equipment, nor in applications where failure ormalfunction of a Nexperia product can reasonably be expectedto result in personal injury, death or severe property or environmentaldamage. Nexperia and its suppliers accept no liability forinclusion and/or use of Nexperia products in such equipment orapplications and therefore such inclusion and/or use is at the customer's ownrisk.

Quick reference data — The Quick reference data is an extract of theproduct data given in the Limiting values and Characteristics sections of thisdocument, and as such is not complete, exhaustive or legally binding.

Applications — Applications that are described herein for any of theseproducts are for illustrative purposes only. Nexperia makes norepresentation or warranty that such applications will be suitable for thespecified use without further testing or modification.

Customers are responsible for the design and operation of theirapplications and products using Nexperia products, and Nexperiaaccepts no liability for any assistance with applications orcustomer product design. It is customer’s sole responsibility to determinewhether the Nexperia product is suitable and fit for thecustomer’s applications and products planned, as well as for the plannedapplication and use of customer’s third party customer(s). Customers shouldprovide appropriate design and operating safeguards to minimize the risksassociated with their applications and products.

Nexperia does not accept any liability related to any default,damage, costs or problem which is based on any weakness or defaultin the customer’s applications or products, or the application or use bycustomer’s third party customer(s). Customer is responsible for doing allnecessary testing for the customer’s applications and products using Nexperiaproducts in order to avoid a default of the applicationsand the products or of the application or use by customer’s third partycustomer(s). Nexperia does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined inthe Absolute Maximum Ratings System of IEC 60134) will cause permanentdamage to the device. Limiting values are stress ratings only and (proper)operation of the device at these or any other conditions above thosegiven in the Recommended operating conditions section (if present) or theCharacteristics sections of this document is not warranted. Constant orrepeated exposure to limiting values will permanently and irreversibly affectthe quality and reliability of the device.

Terms and conditions of commercial sale — Nexperiaproducts are sold subject to the general terms and conditions of commercialsale, as published at http://www.nexperia.com/profile/terms, unless otherwiseagreed in a valid written individual agreement. In case an individualagreement is concluded only the terms and conditions of the respectiveagreement shall apply. Nexperia hereby expressly objects toapplying the customer’s general terms and conditions with regard to thepurchase of Nexperia products by customer.

http://www.nexperia.com/profile/terms





No offer to sell or license — Nothing in this document may be interpretedor construed as an offer to sell products that is open for acceptance or thegrant, conveyance or implication of any license under any copyrights, patentsor other industrial or intellectual property rights.

Export control — This document as well as the item(s) described hereinmay be subject to export control regulations. Export might require a priorauthorization from competent authorities.

Translations — A non-English (translated) version of a document is forreference only. The English version shall prevail in case of any discrepancybetween the translated and English versions.

15.4 TrademarksNotice: All referenced brands, product names, service names andtrademarks are the property of their respective owners.





16. Contents1 General description ............................................... 12 Features and benefits ............................................13 Applications ........................................................... 14 Quick reference data ............................................. 15 Pinning information ...............................................26 Ordering information .............................................27 Marking ................................................................... 28 Limiting values .......................................................29 Thermal characteristics .........................................410 Characteristics .......................................................911 Test information ................................................... 1311.1 Quality information .........................................12 Package outline ................................................... 1413 Soldering .............................................................. 1414 Revision history ...................................................1415 Legal information .................................................1515.1 Data sheet status ............................................... 1515.2 Definitions ...........................................................1515.3 Disclaimers .........................................................1515.4 Trademarks ........................................................ 16

© Nexperia B.V. 2017. All rights reservedFor more information, please visit: http://www.nexperia.comFor sales office addresses, please send an email to: [email protected] Date of release: 14 December 2012

PBSS4230PAN - Nexperia · 2017. 5. 29. · PBSS4230PAN BoAmodPE9(4(RLfc(nlldPNCa)do)odwot Nexperia...

Documents

Transcript of PBSS4230PAN - Nexperia · 2017. 5. 29. · PBSS4230PAN BoAmodPE9(4(RLfc(nlldPNCa)do)odwot Nexperia...