MPX-K & P BASECOAT CONCENTRATES

MPX-K CANDYMPX-P SPECIALTY

PEARLSBASECOAT CONCENTRATES

PRODUCT NUMBER DESCRIPTIONMPX-K SERIES BASECOAT CANDY FX BASECOAT CONCENTRATESMPX-P SERIES BASECOAT SPECIALTY FX PEARL BASECOAT CONCENTRATES

REDUCERS DESCRIPTIONMR-0860 FAST REDUCER (60°-70°F)MR-0870 MEDIUM REDUCER (65°-80°F)MR-0885 SLOW REDUCER (75°-90°F)MR-0895 VERY SLOW REDUCER (85°+F)

ACTIVATOR DESCRIPTIONMX-57 BASECOAT ACTIVATOR

DESCRIPTIONMPX-K Candy FX Basecoat Concentrates and Specialty FX Pearl BasecoatConcentrates offer the perfect blend of candy and pearlessence designed toproduce an appearance similar to that of a candy or pearl finish without theproblems associated with straight candy and pearl midcoats.

COMPATIBLE SUBSTRATES• MP-120 SERIES SEALER • MP-2K PRIMER • OEM FINISHES• MP-EPOXIES • MP-2KGR PRIMER• 2KPB PRIMER • MP3-HS PRIMER• All Matrix basecoats and properly prepared substrates.

*Tech Tip: MPX Series basecoats are the preferred substrate for FX Series Midcoats.

TRI-COAT PAINT PROCESS OVERVIEWThe painting process for these products involves three stages.

Stage One - Apply the proper color MPX or MPB Basecoat per desired coverageper instructions with the recommended surface preparation techniques.

Stage Two - Apply a second color MPX-K Candy FX Basecoat or MPX-P SeriesBasecoats Concentrates as a midcoat over the first basecoat afterrecommended flash time.

Stage Three - Apply Matrix clearcoat over the basecoats after recommendedflash time per appropriate clearcoat tech sheet. 1 of 4

By Matrix

Technical Data SheetTechnical Hotline 888.612.6567

SURFACE PREPARATION1. Final sand surface with 600 wet or dry sandpaper or equivalent.2. Reclean repair area with MX-8000 Pre Paint Cleaner or

MXW-9001 where VOC regulations require use.3. Apply the AccuShade Sealer that best suits the application.

FOUNDATION COATA UNIFORM VEHICLE COLOR IS ESSENTIAL BEFORE BASECOATAPPLICATION. SPRAY A TEST PANEL. Any of the listed compatiblesubstrates may be used as a foundation coat for the MPX basecoat products.

MIXING RATIO

MPX MR-800 SERIES REDUCERS MX-571 Part 1 Part 42.5 grams per rts qt.

Reduce all MPX Series basecoats 1:1 with Matrix MR-0800 seriesreducer.

Note: MX-57 Basecoat Activator is highly recommended for best performance.

Note: Agitate basecoats using a mechanical paint shaker to ensure metallics are in solution prior toreduction. Mix (by volume) 1 parts paint to 1 part reducer to 1.5 oz. MX-57 per RTS qt. Reduce onlywith MR-0800 Series Reducers based on temperature range.

Note: MX-57 Basecoat activator is recommended for use whenever elevated film builds such as thoseresulting from applying multi stage finishes. See the MX-57 Technical Data Sheet for additionalinformation.

Note: Using temperature correct reducers is critical in the application of paint finishes and failure touse the correct temperature reducer can result in a myriad of problems associated with coatings dryingtoo fast or drying too slow.

POT LIFEBasecoat Activator Time Temp

MX-57 2 Hours 77°F

*Tech Tip: Pot life will shorten as temperatures increase. Matrix System products are not recommendedfor use in temperatures below 65° F.

ADDITIVESMX-57 Basecoat Activator, no other additives are required.

MPX-K & P BASECOAT CONCENTRATES

: :

2 of 4

STAGE ONE BASECOAT APPLICATIONMPX OR MPB BASECOAT - See MPX Tech Sheet for completeinstructionsAfter reducing basecoat, strain the paint into the paint gun.Apply 2-3 coats or until hiding is achieved using 35-45 psi at the gun(conventional) or 8-10 psi at the aircap (HVLP). Maintain a distanceof 6-8 inches from the panel with a 90° fan angle to the surface youare painting. Overlap each successive pass by 50%-75% to ensureeven coverage. Allow a 10-15 minute flash time in between coats,allowing the final coat to dry 15-30 minutes prior to topcoatapplication. Do not allow the basecoat to dry in excess of 24 hoursor the basecoat must be lightly sanded and additional basecoatsmust be applied. Apply medium wet coats for best results.

STAGE TWO MIDCOAT APPLICATIONMPX-K OR MPX-P BASECOAT CONCENTRATEAfter adequate flash time for the initial basecoat, apply the secondstage basecoat with the same basecoat application instructions perstage one instructions. CREATING A “LET DOWN” PANEL IS ALWAYSRECOMMENDED TO ENSURE ACCEPTABLE OR DESIRED RESULTSARE OBTAINED.

Note: The second stage may be very translucent and should be test sprayed to determine the numberof coats required to achieve the desired color.

MPX-K & MPX-P Basecoat Concentrates containing Candy FX Dyesmay have limited light fastness and should only be used on surfacesthat have minimal exposure to sunlight.

STAGE THREE CLEARCOAT APPLICATIONAll Matrix clearcoats may be used over MPX-K & MPX-P BasecoatConcentrates per application instructions.

TEST SPRAY OUT REQUIREDIMPORTANT! You must test spray a panel before painting your actual project.This is necessary due to all the variables in the custom painting process. Bytest spraying you will see your end result before you start painting yourproject. You can practice on a panel and change your application techniquesif necessary so your final paint job looks just like you want it to.

ARTWORK & INTERCOAT CLEARDO NOT TAPE DIRECTLY ONTO THE MIDCOAT WHENEVERPOSSIBLE! If artwork is planned, apply 1 or 2 medium coats ofMPB-500 or Matrix clearcoat to protect the underlying paint layerfrom mishaps such as tape marks, chemical spills or etc that maydamage layers applied at a prior date. In addition, the protectiveclearcoat is easier to sand imperfections out of and will not requireto be re-candied after sanding. See tech sheet for moreinformation on MPB-500 or Matrix clearcoat.

3 of 4

MPX-K & P BASECOAT CONCENTRATES

MPX-K & P BASECOAT CONCENTRATES

Rev: 6/15 4 of 4

REPAIRING & RECOATINGMPX-K Candy & MPX-P Specialty Pearl Basecoat Concentrates maybe recoated after 15-30 minutes or up to 24 hours at 77°F withitself, it may be scuffed after 30 minutes at 77°F if necessary. After24 hours depending on temperature/humidity, MPX-P & MPX-KBasecoat Concentrates must be lightly scuffed and a additional coatof MPX-K or MPX-P Basecoat Concentrate midcoat must be applied.

EQUIPMENT CLEANUPClean equipment immediately after use with MX-110 Gun Wash ora high quality lacquer thinner.

EXCLUSIVE WARRANTYThere is no warranty on color match, final color, or application of FXproducts. FX product warranty is exclusively limited to replacement of the FXproduct only, if and when the product is deemed to be defective by Matrixcorporate technical personnel and communicated to the customer in writing.No other contingent liability, labor, or replacement of associated product iscovered by this warranty. This is necessary because of the many applicationvariables involved in the custom painting process. FX Custom Finishes areexcluded from coverage under the Matrix System warranty program.

TECHNICAL DATAColor: VariousMix Ratio: 1 : 1 : 1.5 oz. MX-57 per RTS qt.Viscosity #2 Zahn (RTS): 15 - 18 secondsFilm Build: 0.4 - 0.6 mils per full wet coatPot Life: 2 HoursCoverage (depending on Color): 160 - 241sq. ft.Dust Free: 10 MinutesTack Free: 15-20 MinutesTape Time: 20-40 MinutesV.O.C.: 6.0 - 6.6 lbs gl.Disposal/Safety: see MSDS for this product

Manufactured by Matrix System Automotive Finishes.NOTE: Matrix Systems products are not recommended for use in temperatures below 65°F. Use below thesetemperatures will effect dry times and performance.FOR INDUSTRY USE ONLYRead MSDS Before UseThe contents of the package must be blended with other components before the product can be used. Any mixture of componentswill have hazards of all components. Before opening the packages, read all warning labels. Follow all precautions.The material is designed for application only by professionally trained personnel using proper equipment under controlledconditions, and is not intended for sale to the general public.SEE MSDS AND PRODUCT LABELS FOR ADDITIONAL SAFETY INFORMATION.

© The Valspar Corporation. All Rights Reserved.