Tema-VoyagerTM Multi - VMA-06, VMA-07Quick Installation GuideDocument Number: 800-20479 Rev. 1.5 January 2019

Mounting tools

One 3mm slotted screwdriver (for VMA-07 only) One T10 Torx screwdriver

MAX Power consumption (Tema-Voyager Multi with Plug ins)* : 10-30VDC: 36 W POE+: 25.5 W POE: 15.4 WAvailable current for Readers and Locks*: 10-30VDC: MAX 1500 mA @ 12V POE+: MAX 1500 mA @ 12V POE: MAX 750 mA @ 12V

Operational Temperature: -10 ~ 55°CProtection level: IP32 (inside Tema-Voyager Multi case)Outputs: 4 dry contact NC/NO 3A/30VDC.

Storage Temperature: -25 ~ 70°C

VMA-06 - Technical Specifications

VMA-07- Technical Specifications

Mount VMA-06 and VMA-07 on Voyager Multi1. Determine an appropriate mounting position for the plugs in. If you have a VMA-07 you have to plug it only on the position 1, where VMA-06 can be plugged in any of the 3 sockets' positions (in relation to the outputs to be managed).

- Position 1 drives fixed outputs 1, 2, 3, 4 - Position 2 drives flexible outputs 3, 4, 5, 6 - Position 3 drives flexible outputs 1, 2, 7, 8

2. Switch off the Voyager Multi device.3. Unscrew the cover of the Voyager Multi case and remove it.4. Plug the VMA-0x devices on the Voyager Multi board.5. Set the jumpers required to configure the use of the plug in (turn this sheet for details).6. Wire the outputs as specified in Voyager Multi Quick installation Guide.

1 2 3

What are VMA-06 and VMA-07 devices?VMA-06 and VMA-07 are plug ins used together with Tema-Voyager Multi devices. When these are plugged on the Multi board and properly configured using the related jumpers they turn the open collector digital outputs of the board in relay outputs. VMA-07 includes the connection for an input that drives the cut of the power supply of the device in case of emergency.

7. If you are using VMA-07 wire the input used to cut the POE/ POE+ internal power supply (turn this sheet for details); such wires can enter in the Multi case from the two holes located on the right of the first group of holes on the below margin on the device (see picture).

8. Close and screw the cover of Voyager Multi9. Switch on the Voyager Multi device.

MAX Power consumption (Tema-Voyager Multi with Plug ins)* : 10-30VDC: 36 W POE+: 25.5 W POE: 15.4 WAvailable current for Readers and Locks*: 10-30VDC: MAX 1500 mA @ 12V POE+: MAX 1500 mA @ 12V POE: MAX 750 mA @ 12V

Operational Temperature: -10 ~ 55°CProtection level: IP32 (inside Tema-Voyager Multi case)Outputs: 4 dry contact NC/NO 3A/30VDCInputs: 1 dry contact for emergency alarm

Storage Temperature: -25 ~ 70°C

* Tema-Voyager Multi - Consumption Verifier Tool helps in verifying the consumption of your device

Tema-VoyagerTM Multi - VMA-06, VMA-07

Door lock powered from device

VMA-06 Plug in Wiring diagram VMA-07 Plug in Wiring diagram

Door lock powered from external power supply and driven from internal relay

Possible Relay Output modes

Use of Emergency Input to cutthe door lock power

Direct powering of the door lock

For further details on the Tema-VoyagerTM Multi installation process refer the Tema-VoyagerTM Multi Installation Manual, located it in the following repository:https://extranet.honeywell.com/HBS/EBI/EBIHOME/Pages/default.aspx (EBI home > Product Manuals > TEMA Device Installation Manuals).

The information contained in this manual can be modified at any time without notification.Manufacturer single contact point: Honeywell S.r.l. Via Philips,12 20900 MONZA (Italy)

VMC-xx Mother board Wiring diagram

Configurable I/O

Reader 1 Out 1

J2

Reader 2

Output 1/2 relay selectors(Factory preset: No relay)

Output1: P11, P12Output2: P09, P10

P12

Out 2 In 1 In 2

Fixed I/O

Line 3 Line 4

Line 1 Line 2

Configurable I/O

Reader 3 Reader 4

Out 3 In 4

In 3

Fixed I/O

Line 6 Line 5

Line 8 Line 7

Out

Output 3/4 relay selectors(Factory preset: No relay)

Output3: P07, P08Output4: P04, P05

J4

EGND - +12345678

1 2 3 4 5 6 7 81 2 3 1 2 3 1 2 3

123123123 12

1 2

This picture shows the factory default jumpers positions(to use relay move jumpers on the opposite position: from to )

TB7123

+ 1

2V

OU

T 1

Door Lock

Using Fixed Output 1 Relay Normally open

P13 P26

Output on line 3/4relay selectors(Factory preset: No relay)

Line3: P13, P14 Line4: P03, P26

P10

P09

P11 TB7

TB8

TB1 TB3TB5

TB6 TB2 TB4

Output on line 1/2 relay selectors(Factory preset: No relay)

Line1: P25, P27Line2: P19, P20

P14 P03

P25 P20

P27 P19

P08

P07

P04

P05

TB15TB09

TB16

TB13

TB14

TB11

TB12TB10

P21 P24

P22 P23

P15 P18

P16 P17

Refer to Technical specification for the MAX current powered in relation to the power source used.

P12

P10

P09

P11

TB8

8 6 4 2

7 5 3 1

8 6 4 2

7 5 3 1

P5 P3

P6 P41 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

8 6 4 2

7 5 3 1

8 6 4 2

7 5 3 1

P5 P3

Relay Outputs mode selectors(see below box)

Mother board Connectors(Opposite side)

Mother board Connectors(Opposite side)

1N4004

Isolated Power Supply DC

OUT

AC IN

10 - 30V0V

123

CO

M

NO

/NC

Door lock

1N4004

Output on line 5/6relay selectors(Factory preset: No relay)

Line5: P23, P24 Line6: P21, P22

Output on line 7/8 relay selectors(Factory preset: No relay)

Line7: P17, P18Line8: P15, P16

TB7

P12

P10

P09

P11

TB8

8 6 4 2

7 5 3 1

8 6 4 2

7 5 3 1

P5 P3

VMA-06

Dry Contact Normally Open (Factory preset)

P4

1 3 5 7

2 4 6 8

P6

1 3 5 7

2 4 6 8

8 6 4 2

7 5 3 1P5

8 6 4 2

7 5 3 1

P3

Dry Contact Normally Closed

P4

1 3 5 7

2 4 6 8

P6

1 3 5 7

2 4 6 8

8 6 4 2

7 5 3 1

P5

8 6 4 2

7 5 3 1

P3

P4

1 3 5 7

2 4 6 8

P6

1 3 5 7

2 4 6 8

8 6 4 2

7 5 3 1P5

8 6 4 2

7 5 3 1

P3

P4

1 3 5 7

2 4 6 8

P6

1 3 5 7

2 4 6 8

8 6 4 2

7 5 3 1P5

8 6 4 2

7 5 3 1

P3

Power Output Normally Open

Power Output Normally Closed

VMA-06

Using Fixed Output 1Relay Normally open

J1

Relay Outputs mode selectors(See below box)

Mother board Connectors(Opposite side)

Mother board Connectors(Opposite side)

Input to cut of POE/POE+ power supply

8 6 4 2

7 5 3 1

8 6 4 2

7 5 3 1

P5 P3

P6 P41 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 2 3 1 2

P08

P07

P04

P05

TB09

TB10

J1

P6 P41 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

VMA-07

NO

/NC

CO

M Emergency IN(non polarized,Normally closed)

1 2When door lock is powered from the Voyager Multi device supplied from POE+ using the VMA-07 relay plug in it is possible to have an external signal used to drive the cut of the power at the door. This is used in case of emergency as, for example, in case of fire alarm.Please refer the opposit sheet side on how mount the VMA-07 plug in.

Using VMA-06 and VMA-07 plug ins it ispossible to directly power the door lock. This possibility is conditioned from:- The power source of Voyager Multi - The number and power absorbed from locks - The number and power absorbed from readers and other outputs Please refer the Installation manual for an extensive discussion of this topic and the Tema-Voyager Multi - Consumption Verifier Tool that helps in verifying the consumption.