SRGA2
-
Upload
sofiane-halimi -
Category
Documents
-
view
217 -
download
0
Transcript of SRGA2
-
7/27/2019 SRGA2
1/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
2/21
g Nuovo Pignone
GE Oil & Gas Global Services
Shaft End Labyrinth Seal Clearance
CheckingPut the seal in the shaft, theseal will assume the positionshowed in the picture.
At that point we will set the dial
gage to zero.Now we are going to lift theseal and we will read the radialclearance directly on the dialgage.
0
-
7/27/2019 SRGA2
3/21
g Nuovo Pignone
GE Oil & Gas Global Services
Dc
We read directly thediametralClearance in thegage.
This procedure isalso valid for thebalancing drumlabirint seal.
-
7/27/2019 SRGA2
4/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
5/21
g Nuovo Pignone
GE Oil & Gas Global Services
1
2
34
5
a1
a2a5
a3a4
Masure internal bearingdiametre by an internal dialgage.
Calculate the measureaverage using the following
formula .
5
5
1i ia
A
-
7/27/2019 SRGA2
6/21
g Nuovo Pignone
GE Oil & Gas Global Services
Repet this operation for all Bearing pad.
At the end we will have 5 b values.
Calculate the b measure average bythe following formula:
5
5
1i ib
B
-
7/27/2019 SRGA2
7/21
g Nuovo Pignone
GE Oil & Gas Global Services
A
B
B
C
Using the following
formula it is possible toknow the internal averagediametre colled C
B AC 2
-
7/27/2019 SRGA2
8/21
g Nuovo Pignone
GE Oil & Gas Global Services
D
C
Dc
.so using thefollowignformolu:
DC Dc
It is possible obtainthe diametralclearance
.be careful Dc isthe diametralclearance and NOT the radial one
-
7/27/2019 SRGA2
9/21
g Nuovo Pignone
GE Oil & Gas Global Services
.so if the clearance is out of tolerance we must put some shimplate under the pad, but the pads work radially.
We are going to put shim under the pad having a thickness egualto half diametral clearance.
In fact the shim plate works in radial way.
For example: After all our mesuraments we find out that the diametralclearance Dc has a voule of 0.30mm.
To look at the clearance data sheet it is possible to see that the Journalbearing diametral clearance must be between 0.11 and 0.15 mm.
So to work in the middle of clearance rang (0.11+0.15)/2 =0.13mm we have to
remuve 0.30 0.13 = 0.17mm.The shim plate will have a thickness of 0.17/2 = 0.085mm
-
7/27/2019 SRGA2
10/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
11/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
12/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
13/21
g Nuovo Pignone
GE Oil & Gas Global Services
Ring to be
machined
We are going to put the shim ringsbetween the bearing casing andthe light blu ring
-
7/27/2019 SRGA2
14/21
g Nuovo Pignone
GE Oil & Gas Global Services
Special toolto move theshaft
-
7/27/2019 SRGA2
15/21
g Nuovo Pignone
GE Oil & Gas Global Services
To check and adjust the Thrust bearnig axial clearancethe following procedure must be perform.
The shaft is centred in the diaphargm bundle, so it is in the normal workingcondition. Install the dial gage in discharge side shaft end and set it to ZERO. Move the shaft in discharge direction for about -0.2 mm ( the dial gage readnegative value if it is compressed), in this way we will not have problemsenstalling the external bearing casing. Take the shaft back up to obtain the phisical contact with the active side of the bearing. Read the dial gage, if it is still reading a negative value, disassembly thebearing casing and by turning remuve the right amount of metela, if the dialgage reads positive value the whole shim disc must be replaced with a newone having an higher thickness. Repet the procedure.
Active side
-
7/27/2019 SRGA2
16/21
g Nuovo Pignone
GE Oil & Gas Global Services
Non Activeside
The shaft thrust collar is in contact with the thrust bearing active side padsand the dial gage is reading ZERO. Move the shaft in towords discharge side up to obtain the mechanicalcontact with the thrust bearing non active side.
Read the dial gage and check the amount of clearance. The designe clearance must be between 0.25 and 0.35 mm, so if the dialgage reads a value in the range, OK. If the value is out of the range we needto install the right amount of shim rings under the bearing casing in way toobtain the correct clearance.
-
7/27/2019 SRGA2
17/21
g Nuovo Pignone
GE Oil & Gas Global Services
Thrust Collar
Assembly
-
7/27/2019 SRGA2
18/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
19/21
g Nuovo Pignone
GE Oil & Gas Global Services
V
Amplitude
10
-
7/27/2019 SRGA2
20/21
g Nuovo Pignone
GE Oil & Gas Global Services
-
7/27/2019 SRGA2
21/21
g Nuovo Pignone
GE Oil & Gas Global Services