MAN-QSCA-S-0008 - HMI V01.00.00 - Rev E
Transcript of MAN-QSCA-S-0008 - HMI V01.00.00 - Rev E
HIRSCHMANN MCS
qSCALE maestro PLC v01.00.00
Contents
Safety instructions 1
Product description 2
Service Menus 3
Service and Maintenance 4
Appendix 5
Service Manual
Issue E – 04/2018 HMI v01.00.00 This document has the order number: MAN-QSCA-S-0008
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
2/76
HIRSCHMANN MCS
TABLE OF CONTENTS
1 Safety Instructions ........................................................................................... 7
2 Components ...................................................................................................... 8
2.1 Base Kit with vScale D2 or D3 (102125/102129) ...................................... 8
2.1.1 Junction Box, qSCALE maestro (061179) ............................................. 9 2.1.2 Pressure Sensor Kit (102121) ............................................................. 10
2.2 Boom Upgrade (102124) ......................................................................... 10
2.2.1 Sensor Assembly Length Angle WGX/CAN (061185) ......................... 11
2.3 Boom Kit, New Cable Reel (102126) ....................................................... 11 2.4 Indicator Kit, Light Tower (102127) ......................................................... 12
3 Description of the System ............................................................................. 13
3.1 Product Identification ............................................................................... 15 3.2 General Information ................................................................................. 15 3.3 EC Conformity Declaration ...................................................................... 15 3.4 Overview of Console Elements ................................................................ 16 3.5 Overview Feedback Elements ................................................................. 17
4 Service Menus ................................................................................................ 18
4.1.1 Password Entry .................................................................................... 18 4.1.2 Obtaining the Daily Password .............................................................. 19
4.2 System Settings ....................................................................................... 20
4.2.1 System Settings Breakdown ................................................................ 21 4.2.2 New Password Entry ........................................................................... 23
4.3 Sensor Calibration ................................................................................... 24
4.3.1 Calibrate Angle Sensors ...................................................................... 25 4.3.2 Calibrate Length Sensors .................................................................... 27 4.3.3 Luffing Cylinder Tuning ........................................................................ 29
4.4 Entering Measurements ........................................................................... 32 4.5 Alarm Volume .......................................................................................... 33
5 Service and Maintenance .............................................................................. 34
5.1 Download Application Data ...................................................................... 34 5.2 Reading the Event Recorder ................................................................... 35 5.3 Reset Hour meter .................................................................................... 36 5.4 Change Date and Time ............................................................................ 37 5.5 Rotate Display .......................................................................................... 38 5.6 Screen Capture ........................................................................................ 39
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
3/76
HIRSCHMANN MCS
5.6.1 Taking Screen Captures ...................................................................... 39 5.6.2 Saving Screen Captures ...................................................................... 39
5.7 Mismatched DA4 ..................................................................................... 40 5.8 Maintenance and Repair .......................................................................... 41
6 Troubleshooting ............................................................................................. 42
6.1 Identify the Problem ................................................................................. 42 6.2 Initial System Inspection .......................................................................... 44 6.3 Indicator Definitions ................................................................................. 45
6.3.1 Indicators on Central Control Unit........................................................ 45 6.3.2 Indicators on Console .......................................................................... 45
6.4 Boom Angle Sensing ............................................................................... 46 6.5 Boom Length Sensing ............................................................................. 48
6.5.1 Cable Reel Length Cable Replacement Procedure............................. 49
6.6 Pressure Sensing .................................................................................... 50 6.7 Load Sensing ........................................................................................... 51 6.8 Anti-Two Block Switch (A2B) ................................................................... 52
6.8.1 A2B Problem – Flow Chart .................................................................. 53
6.9 No Console Display ................................................................................. 54 6.10 CAN Bus Communications ...................................................................... 55 6.11 Troubleshooting Sensors With Display .................................................... 58
6.11.1 Readings of CAN Bus Sensors ........................................................ 58 6.11.2 Readings of Digital Inputs ................................................................ 59 6.11.3 Readings of Digital Outputs ............................................................. 60
7 Appendix ......................................................................................................... 61
7.1 Technical Data ......................................................................................... 61 7.2 System Layout Drawing ........................................................................... 62 7.3 Junction Box Wiring Diagram .................................................................. 65 7.4 vSCALE D2 Diagram ............................................................................... 66 7.5 vSCALE D3 Diagram ............................................................................... 67 7.6 Error Codes Table ................................................................................... 68
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
4/76
HIRSCHMANN MCS
VERSION OVERVIEW
Issue Date Description Editor
A 11/2017 Initial Release (HMI v01.00.00) RBM
B 12/2017 Updated Luffing Cylinder Calibration section and
Alarm Volume section.
RBM
C 01/2018 Added backup of product files to Service section RBM
D 04/2018 Added Parts list, troubleshooting and changed
numerical entry.
RBM
E 04/2018 Updated System Layout, added kit drawings RBM
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
5/76
HIRSCHMANN MCS
Introduction
This manual is a component of the equipment or systems supplied by WIKA Mobile Control LP. Keep
this manual in a safe place and ensure that it is available to all users.
The contents of this manual are subject to change. WIKA Mobile Control LP do not provide any guaran-
tee for this material, including the associated guarantee regarding marketability and suitability for cer-
tain intended purposes. WIKA Mobile Control LP accept no liability for errors in the contents of the
manual or for direct or indirect damage in connection with the provision and use of the manual.
This manual is protected by copyright. All rights reserved. The manual may not be duplicated, repro-
duced or translated into another language, either wholly or partly, without the prior written permission of
WIKA Mobile Control LP.
The rendition of common names, trade names, trademarks etc. in this documentation should not be
construed to mean that such names, even without special identification, are free in the sense of trade-
mark and trademark protection legislation and hence usable by anyone.
This device/system is intended exclusively for the tasks described in this manual. Any other use shall
be construed as being inappropriate. The manufacturer accepts no liability for damage caused by inap-
propriate or impermissible use. This device / system may only be used if it is in perfect technical condi-
tion.
Only appropriately qualified personnel may work with this
device / system, i.e. persons:
who are familiar with the operation or installation and commissioning
who know the current regulations for the prevention of accidents
About this manual
Liability disclaimer
Copyright notice
Trademarks
Use for the intended purpose
Qualification of the operating personnel
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
6/76
HIRSCHMANN MCS
Marking of Notices
Dangers and other important notices are marked as follows in this service manual:
WARNING
Warning of direct threat of personal injury and damage to property.
Instructions on precautions to avert the danger.
CAUTION
Warning of dangerous situations. Also warns of damage to property.
Instructions for averting the danger.
IMPORTANT
Warning of possibly damaging situation for the product.
Instructions for avoiding the possibly damaging situation.
NOTE
Usage instructions and information, but no dangerous situation.
HINT
Supplementary comments and recommendations for the user.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
7/76
HIRSCHMANN MCS
1 Safety Instructions
WARNING
Imminent threat of personal injury and damage to property due to incorrect sys-
tem settings!
The correct adjustment of the RCL to the current set-up status is essential for the
correct function of the system and of the machine.
The RCL can only operate correctly if all settings are entered correctly according
to the current set-up status during the SETUP procedure.
The settings can only be carried out by operators who are completely familiar with
the operation and functions of the machine and the RCL.
The correctness of these settings must be guaranteed before starting the machine
operations!
IMPORTANT
Connection to the wrong power supply will cause damage to the device.
The device may only be connected to a DC voltage source of 10 V to 30 V!
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
8/76
HIRSCHMANN MCS
2 Components
Kit Name Kit Number QTY Section
BASE UPGRADE KIT W/ VSCALE D2 102125 1 Section 2.1
BASE UPGRADE KIT W/ VSCALE D3 102129 1 Section 2.1
BOOM UPGRADE (FROM EXISTING 200/208/209 REEL) 102124 1 Section 2.2
BOOM KIT, NEW CABLE REEL 102126 1 Section 2.3
INDICATOR, LIGHT TOWER, MAESTRO, 10M, 3 COLOR (RGY) 102127 1 Section 2.4
2.1 Base Kit with vScale D2 or D3 (102125/102129)
Component Name Part Number QTY Notes
SMC, POWER HARNESS, VSCALE CONSOLE, PWR ONLY, 12' 061106 1
SMC, CONSOLE, VSCALE, D2 - C1, 4.3" DISPLAY 608413 1 D2 kit only
SMC, CONSOLE, VSCALE, D3 - C2, 7", 3 CAM, 4x AI/DI, 3x DO 608416 1 D3 kit only
SMC, QSCALE MAESTRO S6, IP66/67 623029 1
JUNCTION BOX, QSCALE MAESTRO 061179 1 Section 2.1.1
0985 806 125/10M - 90 DEG BEND 900004191 1
ASBSV 4 5 P5 MCS CUSTOM 934637762 1
0935 253 103/3 10967 1
SCREW, SLOTTED PH 5mm x 16mm 002-050-206-112 11
NUT, 5MM HEX NYLON INSERT 031-300-050-468 11
WASHER, 5MM CONCAVE BELLVILLE 000-208-030-050 11
CONSOLE ACCY, KIT 2-1" BALL W/ 4.75" MTG. ARM 031-300-060-382 1 D2 kit only
CONSOLE ACCY, KIT 2 - 1.5 051170 1 D3 kit only
SMC, CONSOLE ACCY, RAM MOUNT ADAPTER, iSCOUT D2 608460 1 D2 kit only
SMC, CONSOLE ACCY, RAM MOUNT 608464 1 D3 kit only
SMC, DUMMY PLUG ASSY, 48-PIN 060980 1
BRACKET, EXTERNAL MOUNTING FEET 2/PACK, FOR MAESTRO 051309 1
SCREW M4X12MM NARROW HEAD PHILLIPS STAINLESS STEEL 051310 4
ZVK 12291 600000991 2
0909 UAC 101 600003038 2
KIT, QSCALE IX, LOAD, PSENS, DAVS, 300 BAR, SAE 6, ID 60/61 102121 1 Section 2.1.2
STRAIN RELIEF ACCY, PFLITSCH RUBBER HOLE PLUG BO 4-6.5MM 051292 7
STRAIN RELIEF ACCY, PFLITSCH RUBBER HOLE PLUG BO 9-13MM 051293 1
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
9/76
HIRSCHMANN MCS
2.1.1 Junction Box, qSCALE maestro (061179)
Component Name Part Number QTY JUNCTION BOX, 160x240X81 061180 1
TERMINAL STRIP ACCY, RAIL MAESTRO 9IN 051295 1
HARNESS, QSCALE MAESTRO CONTROLLER TO JUNCTION BOX 061178 1
WASHER, LOCK 1/4 000-208-040-070 2
TERMINAL STRIP ACCY, BLOCK, PIK 4N W/BAR 051296 7
TERMINAL STRIP ACCY, BLOCK, PIK 4N WO/BAR 051297 12
TERMINAL STRIP ACCY, BLOCK PIK 4N W/DIODE 061181 1
EC, DIODE, 1N4003 200V/1A 000-430-104-003
TERMINAL STRIP ACCY, END PLATE, PIK 4N 051298 1
TERMINAL STRIP ACCY, END BRACKET, PIK 4N 051299 2
RELAY, SHUTOFF 12V 20/30A 000-304-140-112 1
EC, DIODE, 1N4003 200V/1A 000-430-104-003 2
KEYSWITCH, CENTRAL UNIT, NEW 024-350-100-768 1
CENTRAL UNIT ACCY, MEMBRANE 024-000-100-095 1
STRAIN RELIEF, PG13.5 12-15mm 021-441-161-213 1
STRAIN RELIEF, PG 9 4-6mm, 021-441-060-409 6
STRAIN RELIEF, PG 9 5.5mm, 021-441-090-709 1
TAPE, 3M, VHB 5925 1 031-300-050-765
STRAIN RELIEF, PG13.5 8-12mm 021-441-131-013 3
WIRE, HOOKUP 18 AWG BLUE 123-429-910-960 0.6 ft
WIRE, HOOKUP 20 AWG GREEN 123-429-901-830 0.6 ft
WIRE, HOOKUP 18 AWG BROWN 123-429-910-880 0.6 ft
WIRE, HOOKUP 18 AWG BLACK 123-429-907-280 3.6 ft
WIRING ACCY, CRIMP TERMINAL, 18-22AWG, INSULATED, RED 051304 4
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
10/76
HIRSCHMANN MCS
2.1.2 Pressure Sensor Kit (102121)
Component Name Part Number QTY SENSOR,PRESS,SINGLE,CAN,ID 60 061091 1
SENSOR, PRESS TRANS, CAN,ID 61 061092 1
0935 253 103/5 M 10968 2
SENSOR ACCY, CUTTING RING DKA 000-209-140-016 2
HYDR, ADAPTER, BULKHEAD 9/16- 000-214-600-093 2
HYDR, ADAPTER, 9/16-18 UNF-2B; 031-300-050-689 2
HYDR, FITTING, 1/4 NPT MALE TO 031-300-050-750 2
2.2 Boom Upgrade (102124)
Component Name Part Number QTY Notes STRAIN RELIEF, PG13.5/PG 9 000-214-261-309 1
STRAIN RELIEF ACCY, PFLITSCH RUBBER HOLE PLUG BO 4-6.5MM
051292 2
STRAIN RELIEF ACCY, PFLITSCH RUBBER HOLE PLUG BO 9-13MM 051293 2
0935 253 103/15 M 27866 1
STRAIN RELIEF, PG13.5 HOLE 000-214-340-013 1
STRAIN RELIEF, PG11/PG 9 000-214-261-109 1
STRAIN RELIEF, PG11 HOLE PLUG 000-214-340-011 1
SENSOR ASSY, LENGTH/ANGLE, WGX/CAN 061185 1 Section 2.2.1
SCREW, 6mm X 12mm SOCKET CAP 002-050-206-012 3
WASHER, FLAT 6MM 000-207-010-064 3
SENSOR, LENGTH POT.W/O 067-000-100-204 1
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
11/76
HIRSCHMANN MCS
2.2.1 Sensor Assembly Length Angle WGX/CAN (061185)
Component Name Part Number QTY SENSOR, ANGLE, WGX 360/3510, ACTIVATED RESISTOR, 125KBPS, CA 061194 1
CONNECTOR ACCY, JST, EH 7POS 051207 1
BOARD, LENGTH & A2B CAN -120 535950 1
RSF 5/0.5M (#5 wire GY) 600000558 1
PLATE, CABLE REEL UPGRADE, MAESTRO 051307 1
CONN ACCY, TERMINAL CRIMP, EH 051208 5
M4x30mm BOLT 051278 3
HARDWARE, LOCKWASHER, M4 051177 3
NUT, 4mm, SELF LOCKING, S.S 002-060-500-402 3
HARDWARE, STANDOFF 3mm x 12 FF 000-212-020-312 3
SCREW,3mm x 10mm PANHD PHILLIP 002-053-703-101 6
WASHER, 3mm CONCAVE BELLVILLE 000-208-030-030 9
2.3 Boom Kit, New Cable Reel (102126)
Component Name Part Number QTY Notes CABLE REEL, KT200, STANDARD 006-820-006-002 1.00
SENSOR ACCY, GEAR WHEEL, KT200 068-000-110-038 1.00
STRAIN RELIEF, PG13.5/PG 9 000-214-261-309 1.00
0935 253 103/15 M 27866 1.00
SENSOR ASSY, LENGTH/ANGLE, WGX/CAN 061185 1.00 Section 2.2.1
SCREW, 6mm X 12mm SOCKET CAP 002-050-206-012 3.00
WASHER, FLAT 6MM 000-207-010-064 3.00
SENSOR, LENGTH POT.W/O 067-000-100-204 1.00
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
12/76
HIRSCHMANN MCS
2.4 Indicator Kit, Light Tower (102127)
Component Name Part Number QTY INDICATOR, LIGHT TOWER, 3 COLOR LED (GRN, YEL, RED) 051264 1.00
INDICATOR ACCY, POWER MODULE (FOR #051264 LIGHT TOWER) 051265 1.00
0935 253 105/10 M 15734 1.00
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
13/76
HIRSCHMANN MCS
3 Description of the System
The maestro system (also referred to as ‘RCL’) is a CAN bus system comprised of a central
microprocessor unit, operating console, angle sensor, tilt sensor, load pin, and anti-two block
switch. All components and sensors are equipped with CAN bus controllers.
When limits are reached an overload warning signal is generated at the operator’s console. At
the same time, the Function Kick Out (FKO) outputs are deactivated thus ‘locking out’ the opera-
tor and stopping aggravating machine movements. The fixed data regarding the machine (ex.
capacity charts, boom weights, centers of gravity, etc.) are stored in memory chips in the central
processor unit. This data is the reference information used to calculate the operating conditions.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
14/76
HIRSCHMANN MCS
NOTE
This service manual contains information about the vSCALE D2 / D3 maestro con-
sole,
mode selection, operation, sensor calibration and maintenance.
WARNING
This service manual contains information about the vSCALE D2 / D3 maestro
console, mode selection, operation, sensor calibration and maintenance.
Although the system incorporates functions for monitoring adjustable geomet-
rical limit values with visual and audible warnings and a relay output in the event
of limit values being exceeded, the system cannot be used as an operational limit
switch.
The machine driver is responsible for the safe operation of the machine.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
15/76
HIRSCHMANN MCS
3.1 Product Identification
The type plate carries the unique identification of the operating console. It is located on the back of the
device.
Please ensure you make a note of all the information on your type plate for queries about this product.
3.2 General Information
NOTE
Knowledge of how to use a voltmeter to measure both voltage and current is as-
sumed.
HINT
For general system operation, refer to the console Operator’s Manual.
3.3 EC Conformity Declaration
The technical design and construction of the qSCALE maestro system corresponds to requirements of
the EMC directive 2004/108/EC and therefore carries the CE symbol.
The device complies with the following standards:
EN 12895:200, EN 13309:2010, EN ISO 14982: 2009
The full conformity declaration is available from the manufacturer on request.
Type plate (Example for D3)
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
16/76
HIRSCHMANN MCS
3.4 Overview of Console Elements
Function Keys F1 to F12: Calls Functions
Encoder With Pushbutton Function: For Selection and Confirmation
SET key: Selects Settings / Silences Alarm
HOME key: Returns to Main Working Screen
ESCAPE key: Aborts Function
Display with RCL Main Menu
Rotary Encoder with Pushbutton Function For Selection and Con-firmation
"Set" Key Selects Settings / Silences Alarm
"Home" Key (Return to RCL Main Operating Screen)
"Escape" Key Aborts Function / Returns to
previous screeen
Feedback Elements (See Section 3.5)
Function Keys F1-F8 (F1 – F12 in 7” display ver-sion.) Function Varies by screen
USB 2.0 interface (used for service purposes)
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
17/76
HIRSCHMANN MCS
3.5 Overview Feedback Elements
Light Sensor: Not Used
Operating Display: Green While Supply Voltage is Connected
USB Data Display: Yellow During Data Exchange via Front USB Port
Wireless Indicator: Not Used
Multi-Function Light:
/ Flashes Red/White while in error state
Blue while setting the operating mode
Green while in operation
Yellow Machine nearing operational limit
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
18/76
HIRSCHMANN MCS
4 Service Menus
This chapter contains information, advice, and instructions for navigating and using the service menus.
4.1.1 Password Entry
In order to access certain menus it is necessary to enter a Service Password, Daily Password or LMI Password (See Section 4.1.2 for information on Obtaining the daily password.)
Password entry is done by the following instructions:
Use the rotary knob to select the numbers.
Pressing the knob moves to the next digit and selects right arrow.
Pressing the right arrow when the curser is to the right of the last number confirms the entry
Use the or buttons to select the number in the chosen direction. (The selected digit turns green and will be
replaced by the next selection.)
Use the button to delete the currently selected digit.
Press to confirm the password as displayed.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
19/76
HIRSCHMANN MCS
CAUTION
Entering the Service Password will unlock all service functions on the console until it is reset.
Always reset the console when service is complete to lock access to service menus.
4.1.2 Obtaining the Daily Password
Summary In order to obtain the Daily Password you must find the Daily Password Seed in the Settings Menu and enter it into the excel sheet to be converted into a usable password that will last the entire day.
Finding the Daily Password Seed
The Daily Password Seed is located in the Settings Menu in the bottom center of the screen above the Information Bar.
HOME SETTINGS
Converting the Seed into the Daily Password
Open the DailyPassword_maestro.xls document and enter the Daily Password Seed into the field beside the “Console” cell and then press the TAB key.
The DailyPassword_maestro.xlsx document will then generate a daily password next to the “Password” cell.
This password will allow access to service functions until the console’s internal clock reaches 12:00am at which time a new seed is created.
Daily Password Seed.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
20/76
HIRSCHMANN MCS
4.2 System Settings
HOME SETTINGS SYSTEM SETTINGS
Function Keys
And
Choose option to adjust.
(See Section 4.2.1 for explanations of each option.)
And
Adjust chosen option.
(See Section 4.2.1 for explanations of each option.)
New Password Entry.
(See Section 4.2.2)
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
21/76
HIRSCHMANN MCS
4.2.1 System Settings Breakdown
Toggling Wind Speed Display
Use the or keys to select the Wind Speed option.
Use the or keys to set the Wind Speed display to 0 (off) or 1 (on).
Setting the Wind Speed Display to 0 (off) removes the Wind Speed Display from the Information Bar in the Main Operat-ing Screen.
Wind Speed Display On:
Wind Speed Display Off:
Toggling Jib Status Display
Use the or keys to select the Jib Status option.
Use the or keys to set the Jib Status display to 0 (off) or 1 (on).
Setting the Jib Status Display to 0 (off) removes the Jib Height and Jib Angle values from the Main Operating Screen.
Jib Status On: Jib Status Off:
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
22/76
HIRSCHMANN MCS
Toggling Cameras
Use the or keys to select the Camera option.
Use the or keys to set the Camera option to 0 (off) or select the number of cameras to activate.
Setting the Camera option to 1 or more enables the function key from the Main Operating Screen.
Camera(s) On: Camera Off:
Toggling Camera Full-Screen Style
Use the or keys to select the Full Screen option.
Use the or keys to set the Full Screen Style to 0 (partial full screen) or 1 (complete full screen).
Setting the Full Screen Style to 1 (complete full screen) causes the function key to fully fill the screen with the selected camera feed covering the function keys and Information Bar
Full Screen 0: Full Screen 1:
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
23/76
HIRSCHMANN MCS
4.2.2 New Password Entry
Summary You can change the active password, for example from a the Daily Password to the Service Password, using the New Password Entry button in the System Settings Screen
HOME SETTINGS SYSTEM SETTINGS
NEW PASSWORD
See Section 4.1.1 for instructions on entering the new password.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
24/76
HIRSCHMANN MCS
4.3 Sensor Calibration
Summary To calibrate the sensors you must position the machine as directed to set minimum and maximum values. Calibrating the sensors can be accessed through the System Menu. To calibrate sensors an LMI or System Password is required.
HOME SETTINGS SENSOR CALIBRATION
Function Keys
Calibrate Angle Sensor
Calibrate Length Sensor
Luffing Cylinder Tuning
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
25/76
HIRSCHMANN MCS
4.3.1 Calibrate Angle Sensors
Summary This section describes how to calibrate the boom angle sensor. The machine must be on a level surface to calibrate this sensor.
HOME SETTINGS SENSOR CALIBRATION
ANGLE SENSOR
CALIBRATION
Fully retract the boom and press
Fully lower the boom and press
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
26/76
HIRSCHMANN MCS
Enter the Measured Angle of the Boom
Use the rotary knob to select the numbers. (See Section 4.4 for detailed instructions.)
Press to confirm the measured boom angle as entered.
Angle up the boom a minimum of 5 degrees.
The will turn into when the boom angle has been sufficiently changed.
Press
Calibration is complete.
Press to complete the boom angle calibration pro-cedure
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
27/76
HIRSCHMANN MCS
4.3.2 Calibrate Length Sensors
Summary This section describes how to calibrate the boom length sensor. The machine must be on a level surface to calibrate this sensor.
HOME SETTINGS SENSOR CALIBRATION
LENGTH SENSOR
CALIBRATION
Fully retract the boom and press
Enter the Measured Length of the Boom
Use the rotary knob to select the numbers. (See Section 4.4 for detailed instructions.)
Press to confirm the measured boom length as entered.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
28/76
HIRSCHMANN MCS
Fully extend the boom and press
Enter the Measured Length of the Boom
Use the rotary knob to select the numbers. (See Section 4.4 for detailed instructions.)
Press to confirm the measured boom length as entered.
Calibration is complete.
Press to complete the boom angle calibration pro-cedure
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
29/76
HIRSCHMANN MCS
4.3.3 Luffing Cylinder Tuning
Description Luffing Cylinder Tuning adjusts the lift cylinder rod and piston geometric data to correct system-atic errors in the load display. The adjustment computed applies equally to all operating modes at all length and angle points.
HOME SETTINGS SENSOR CALIBRATION
LUFFING CYLINDER
TUNING
Function Keys
Set Empty Load Weight (Measurement A)
Set Fully Load Weight (Measurement B)
Compute Factors
Apply computed factors to controller
Function disabled until both loads measured
Function disabled until factors computed
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
30/76
HIRSCHMANN MCS
Before beginning perform the following
1) Configure the machine to a main boom operating mode.
2) Fully retract the boom.
3) Remove all weight from the main and auxiliary hoist hooks.
4) Configure the reeving to allow a pick of the largest known load available.
Remove any weight from the machine and fully retract the boom.
Press the function key to begin setting the Empty Load Weight
Allow a few moments for the measurement to complete.
The measurement will not complete if the piston pressure is 0 or the rod and piston pressure are changing outside of 5 bar
Enter the weight currently attached to the hook. If empty enter 0.
Use the rotary knob to select the numbers. (See Section 4.4 for detailed instructions.)
Press to confirm the weight as entered.
Pick a heavy and known weight.
Wait for the machine to settle.
Press the function key. Allow a few moments for the measurement to complete. The measurement will not complete if the piston pressure is 0 or the rod and piston pressure are changing outside of 5 bar.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
31/76
HIRSCHMANN MCS
Enter the known weight of the load and any rigging added.
Use the rotary knob to select the numbers. (See Section 4.4 for detailed instructions.)
Press to confirm the load weight as entered.
Press the function key to begin computing the
factors.
Allow a few moments for the factors to compute.
Press the function key to save the configuration.
If the process fails due to communication errors, but the system acts correctly otherwise, a reboot is required.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
32/76
HIRSCHMANN MCS
4.4 Entering Measurements
This section describes the process for entering numerical measurements into the dialog box while calibrating sensors.
Use the rotary knob to select the numbers.
Pressing the knob moves to the next digit and selects
right arrow.
Pressing the right arrow when the curser is to the right
of the last number confirms the entry
Press the button to add a decimal point.
Use the button to change the input between a nega-tive or positive value.
Use the or buttons to select the number in the chosen direction. (The selected digit turns green.)
Use the button to delete the currently selected digit.
Press to confirm the measurement value as en-tered.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
33/76
HIRSCHMANN MCS
4.5 Alarm Volume
The Alarm Volume can be adjusted in the User Screen.
An OEM or LMI password must be entered in order to change the volume. (See section 4.1.1)
HOME SETTINGS OUTPUT
PREFFERENCES
ALARM
VOLUME
Use the rotary knob to adjust the volume.
Pressing the knob or to confirm.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
34/76
HIRSCHMANN MCS
5 Service and Maintenance
5.1 Download Application Data
The system is able to store multiple Application Files (i.e. machine model and load charts).
HOME SETTINGS SYSTEM INFORMATION
DOWNLOAD APP DATA
Adding machine project file packages to the console memory is done by the following instructions:
Insert a USB drive, with the desired project file packages, to the console’s USB port
Press the function key.
The machine project files will now be available.
The previous copy of the project files will be saved to the USB drive in a folder bkup_YYYY-MM-DD_HH-MM-SS If there were no files previously the folder will be empty.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
35/76
HIRSCHMANN MCS
5.2 Reading the Event Recorder
The user is able to download the stored event records via the vSCALE console to a USB drive. The USB drive must be for-matted with a fat32 filesystem before downloading can be completed.
HOME SETTINGS SYSTEM INFORMATION
LOG DATA
Obtain a blank FAT32 USB drive.
Insert the blank USB drive into the USB port on the front of the vSCALE console.
Press the function button to download the record-ed events to the USB drive.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
36/76
HIRSCHMANN MCS
5.3 Reset Hour meter
HOME SETTINGS SYSTEM INFORMATION
RESET HOUR METER
This resets the hours the system has been on to 0.
Press to confirm and reset the hour meter.
Press to cancel and return to the System Infor-mation Screen
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
37/76
HIRSCHMANN MCS
5.4 Change Date and Time
HOME SETTINGS SYSTEM INFORMATION
SET DATE/TIME
Adjust the date and time by using and
Use to move to the next value.
The date and time format is as follows:
HH:MM:SS DD-MM-YY
Press to confirm the new time and date.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
38/76
HIRSCHMANN MCS
5.5 Rotate Display
HOME SETTINGS SYSTEM INFORMATION
ROTATE DISPLAY
The display can be rotated 90 degrees at a time by
pressing .
NOTE
The location of the function keys change as the screen
is rotated. When rotating the screen multiple times ensure
after each rotation that you are pressing the correct key.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
39/76
HIRSCHMANN MCS
5.6 Screen Capture
The system has the capability of taking screenshots and saved to either:
1. USB Drive
2. Internal Memory
5.6.1 Taking Screen Captures
On any screen:
o Press and hold the “HOME” function button
o Press the “SET” function button
o Release both the “HOME” and “SET” function buttons simultaneously
o A screen shot of the current screen will be saved.
5.6.2 Saving Screen Captures
If a USB drive is installed in the console, the screen capture will be saved to the USB drive.
If a USB drive is not installed in the console, the image will be saved to the internal memory of the
console.
If using internal memory, only 20 images may be saved. After 20 images are saved, additional screen
captures will not be saved. The saved images can be transferred to a USB drive. This is done by:
1. Installing a USB drive
2. Take a new screenshot.
Once a screenshot is taken the images in internal memory are copied to the USB drive and
removed from internal memory.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
40/76
HIRSCHMANN MCS
5.7 Mismatched DA4
One of the following messages may be displayed after an installation error or software corruption.
If an installation error is not suspected contact your service representative.
To resolve the error the project file must be reinstalled using the procedure described in section 5.1.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
41/76
HIRSCHMANN MCS
5.8 Maintenance and Repair
The qSCALE S6 maestro central control unit and vSCALE D2 / D3 maestro console contain no
wearing parts and therefore cannot be opened. If you notice malfunctions or differences between
measured and displayed values, you should switch the device off and have it checked and, if neces-
sary, repaired immediately by an authorized WIKA service partner.
Clean the surface and the front screen of the device occasionally with a damp cloth and a mild deter-
gent. Never use abrasive or aggressive detergents as these may damage the device.
IMPORTANT
Device may be damaged by the use of high-pressure cleaners.
The device must not be treated with a high-pressure cleaner or similarly aggressive method
under any circumstances!
Condensation inside the vSCALE D2 / D3 maestro console can damage electronic components or the
LCD and can condense at the inner side of the front glass/touch. Although the vSCALE D2 / D3 maes-
tro console is designed as a closed housing with a Gore-Tex-Membrane for breathing, condensation
may occur as a physical effect, if the console is exposed to unfavorable temperature/humidity cycles,
which pumps humidity inside the housing.
Damage to the front foil can lead to the penetration of moisture and dirt into the interior of the device,
which must then be properly repaired without delay.
Keep the contacts and the area around the device connectors clean and check occasionally that all
connections are secure.
If parts are damaged, they must be properly repaired or replaced immediately.
Maintenance
Cleaning
Usage
Repair
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
42/76
HIRSCHMANN MCS
6 Troubleshooting
6.1 Identify the Problem
In most cases, your problem will fall under the following categories:
I HAVE AN ERROR CODE INDICATED ON THE CONSOLE
Please go to Section 7.6 Error Codes Table
THE DISPLAYED ANGLE DOES NOT MATCH THE MEASURED BOOM ANGLE
Start in Section 6.4 Boom Angle Sensing to troubleshoot possible problems with the boom angle
measurement.
THE DISPLAYED LENGTH DOES NOT MATCH THE MEASURED BOOM LENGTH
Start in section 6.5 Boom Length Sensing to troubleshoot possible problems with the boom length
measurement.
THE DISPLAYED PRESSURES DOES NOT MATCH THE MEASURED PRESSURES
Start in section 6.6 Pressure Sensing to troubleshoot possible problems with the pressure transducers.
THE DISPLAYED LOAD DOES NOT MATCH THE MEASURED LOAD
Please note that the indicated load is calculated by the system from the geometry information in the
computer, the operator’s selections, and all the sensor inputs. If the load display is off, it may be due to
an error in any or several of these inputs! Refer to section 6.7 Load Sensing to narrow down the source
of your problem.
Questions:
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
43/76
HIRSCHMANN MCS
THE CONSOLE DISPLAY IS BLANK
If the console does not show any sign at all (no lights, no buzzer, and no display), the problem is in the
wiring between console and central unit, or the console itself has a problem. Refer to section 6.9 No
Console Display for further troubleshooting.
I HAVE AN A2B PROBLEM
Please go to section 6.8 Anti-Two Block Switch (A2B).
I HAVE A CAN BUS PROBLEM
Please go to section 6.10 CAN Bus Communication.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
44/76
HIRSCHMANN MCS
6.2 Initial System Inspection
Check all CAN cables for breaks, cuts or damage of any kind.
Check connections at sensors and at the CAN Junction Box
Check for water across the terminals in the CAN bus or inside the Junction Box
Cycle System Power. A Waiting for Connection error can be caused by cycling the system power off and on too quickly.
There must be a minimum of 10 seconds between powering off and back on again.
Low system voltage can cause CAN bus errors.
Off … Wait 10 Seconds…
On
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
45/76
HIRSCHMANN MCS
6.3 Indicator Definitions
Indicators are located on the Central Control Unit and the Console to assist with troubleshooting basic
power and software issues.
6.3.1 Indicators on Central Control Unit
Visual LED indicators are located on the top of the Central Control Unit.
PON Is lit solid when Power to the controller is ON
POK Is lit solid when Power is OK indicating that the power supply circuitry is good and the controller is providing the expected amount of power output to the rest of the system.
SR Is lit solid when the Safety Relay is Active. If this light is off it indicates a segmentation fault, memory leak, or another condition that prevents the system from showing safe working areas. A soft reset will not reset the safety relay, to do so you must fully power down the controller and power it back on.
RUN Is lit solid when CoDeSys Application is RUNning.
ERR Software ERRor
The system software controls this LED; the normal case is that the LED is off. If the LED is ON, or a flashing code is shown, then there is an error. Note: The ERR light will turn on briefly during start-up and then turn off. This is normal behaviour.
S1 Application-Specific control indicator.
If the LED is ON solid, the application is running; if it is flashing, there is a safety system malfunction or missing crane information.
6.3.2 Indicators on Console
See Section 3.5 for definitions of indicators on the console.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
46/76
HIRSCHMANN MCS
Cable Reel
6.4 Boom Angle Sensing
The system measures the angle of the main boom of the machine with an angle sensor. The angle
sensor is contained within the cable reel, located on the main boom.
Start by verifying the measured angle to display the angle at several positions. The CAN Bus is digital
and as such will either transmit the signal correctly or not at all. The scaled value of the sensor can be
monitored and should be checked against a digital level outside of the system mounted on the boom. If
the scaled value varies from the measured value, replace the angle sensor. Refer to sensor documen-
tation for expected accuracy values.
The voltage supplied to either sensor should ideally be between 11.0 and 26.0V. The angle sensor is
located within a cable reel where it is connected to an LGH board and then to a CAN bus. This board
will supply the sensor with power.
The signal runs from the angle sensor to the LGH Board, both located in the cable reel. From there, it
travels as digital information to the central processing unit.
Basic Troubleshooting
Block Diagram
Angle Sensor
LGH Board
CAN Bus
qSCALE
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
47/76
HIRSCHMANN MCS
BR
NW
HT
YE
LR
ED
Measure the voltage between pins 3 (GND) and 2 (+) while the angle sensor is still connected to the
LGH Board. If the voltage is not within the acceptable range, unplug the sensor and re-measure. If
unplugging the sensor resolved the voltage issue, replace the sensor. If the voltage is still outside of the
acceptable range, unplug the power source to the LGH Board and re-measure. If unplugging the board
resolved the voltage issue, replace the board. If the voltage is still outside of the acceptable range,
power to the CAN line may be the issue. Check the entire CAN Bus system to ensure proper wiring and
connections.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
48/76
HIRSCHMANN MCS
Cable Reel
6.5 Boom Length Sensing
The system measures the length of the main boom of the machine with a length sensor. The length
sensor is contained within the cable reel, located on the left side of the main boom.
Start by verifying the measured length to the display. Boom length is the short and long distance shown
on the load chart. The boom length is displayed on the working screen of the console. The LGH Board
is digital and as such will either transmit the signal correctly or not at all. If the length measurement
does not match the displayed length, start troubleshooting by fully retracting the boom and checking the
length cable tension. If tension is lacking, check the cable reel to ensure it has the proper pretension.
This varies upon the type of cable reel used.
The voltage supplied to the length sensor will be through the LGH Board.
The sensor outputs a CAN signal directly and plugs into an LGH Board. The ideal voltage supplied to
the rotary encoder should be between 11.0 and 26.0V.
Measure the voltage between pins 3 (GND) and 2 (+) while the rotary encoder is still connected to the
LGH Board. If the voltage is not within the acceptable range, unplug the sensor and re-measure. If
unplugging the sensor resolved the voltage issue, replace the sensor. If the voltage is still outside of the
acceptable range, unplug the power source to the LGH Board and re-measure. If unplugging the board
resolved the voltage issue, replace the board. If the voltage is still outside of the acceptable range,
power to the CAN line may be the issue. Check the entire CAN Bus system to ensure proper wiring and
connections.
Basic Troubleshooting
Block Diagram
Length Sensor
LGH Board
CAN Bus
qSCALE
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
49/76
HIRSCHMANN MCS
6.5.1 Cable Reel Length Cable Replacement Procedure
Replace the length cable using the following procedure:
1. Fully retract the boom and lock cable reel from rotating.
2. Cut old cable at cable drum.
3. Remove length cable from cable guides and disconnect from boom tip connection.
4. Open the junction box on the bottom of the reel.
5. Take note of the wiring of the length cable to the terminal strip!
6. Loosen the strain relief and remove damaged length cable from terminal strip
7. Feed new length cable through hole on reel drum through the strain relief on the junction box.
8. Rewire terminal strip according to wiring noted in step 4.
9. Close junction box and tighten strain relief.
10. Remount cable reel to the boom.
11. Re-spool the drum by rotating the reeling drum clockwise (reverse) until all cable length is
neatly wrapped in drum.
12. Let the reel unwind to a neutral state after drum has been re-spooled.
13. Set pre-tension on cable reel by rotating the drum counterclockwise (forward) 3 rotations.
14. After setting pre-tension, hold the reel in place so that the cable can be unwound to run it
through the boom.
15. Remove appropriate number of cable wraps from the drum to get enough cable length to run
through the boom.
16. Connect the length cable to the appropriate boom tip connection.
Procedure for Length Cable Replacement
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
50/76
HIRSCHMANN MCS
6.6 Pressure Sensing
The System measures the pressure of the boom lift cylinder for both rod and piston side. Both sensors
communicate on the CAN Bus.
The signal runs from the pressure transducer as digital information on the CAN Bus to the central unit. Note that the load displayed on the LMI is not a direct measurement when using pressure transducers; rather, it is a calculated value. Ensure that the hydraulic system is functioning as intended and that sensor values, mainly length and angle, are functioning correctly prior to troubleshooting the pressure transducers.
HOME SETTINGS MACHINE INFO
ANALOG INPUTS
Possible Error Symbols
Short to Ground
Short to Battery
Not
Calibrated
Deactivated
Open Circuit
Response Timeout No Signal From
Sensor
Confirm that the Rod and Piston pressure sensors initialized without errors in the Analog Inputs screen. See Section 6.11.1 for details on the meanings of possible error codes.
Block Diagram
Rod Pressure Sensor
CAN Bus
qSCALE
Piston Pressure Sensor
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
51/76
HIRSCHMANN MCS
6.7 Load Sensing
Please note that the load displayed by the RCL is not a direct measurement, but a calculated value
that is based on many factors. Factors included that are outside of the measured values include:
Operator settings such as:
Operating mode/configuration
Parts of Line/Reeving
Outrigger position
Rigging parts such as:
Hook block weight
Sling weights, etc.
Tip height (length of load line used)
Boom weights
Boom attachments such as:
Stowed jibs
Glass jib, telescopic jib, etc.
Before checking the system for a load-reading problem, make sure all of the above has been ruled out.
When you still feel the system is reading a sensor wrong and thus displaying an incorrect load, use the
following:
Use the previous sections and the individual sensor signal displayed on the screen to double-check the
following:
boom length reading
angle transducer reading
pressure transducer readings
If all are correct, use the zero setting and calibration screens to zero pressure transducers, calibrate
angle, and length. If you still have a problem, replace pressure transducer(s).
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
52/76
HIRSCHMANN MCS
Cable Reel
6.8 Anti-Two Block Switch (A2B)
The system measures the load block and its relationship to the head of the boom. The A2B switch is
located at the tip of the boom.
The signal runs from the A2B as a CAN Bus input of the central unit.
NOTE
Some systems have two (2) A2B switches wired in series.
Block Diagram
A2B Sensor
LGH Board
CAN Bus
qSCALE
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
53/76
HIRSCHMANN MCS
6.8.1 A2B Problem – Flow Chart
Use the following flow chart to troubleshoot errors with A2B switch input.
Flow Chart
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
54/76
HIRSCHMANN MCS
6.9 No Console Display
If the console never displays an image, check if power is being supplied to the console. Measure the
voltage between Pin 1 (+) and Pin 3 (GND). If power is being supplied, the console must be replaced.
If power is not being supplied, trace the wiring to determine why.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
55/76
HIRSCHMANN MCS
6.10 CAN Bus Communications
CAN Bus - a serial bus protocol to connect individual systems and sensors as an alternative to con-
ventional multi-wire cables. It allows crane components to communicate on a single bus: a dual-wire
networked data bus with speed up to 1Mbps.
The use of a CAN Bus design allows for all nodes (sensor, controller and console) signals to be net-
worked over a common pair of cables. The signals generated by all sensors are slave signals sent with
a digital identifier over common cables. The data transmitted is used by the controller (master). The
data can be interpreted, and information and controls sent from the controller to provide crane safety
functions. Each node has a unique identifier. This allows for a common pair of shielded wires (the bus)
to carry all signals.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
56/76
HIRSCHMANN MCS
The CAN Bus requires that 120 Ohm resistors be at each end of the CAN bus The resistors in parallel
yield 60 Ohms of resistance between the CAN High and CAN Low cables.
One of these resistors is located inside the qSCALE maestro S6 Controller. The other is in the WGX
angle sensor contained in the Cable Reel.
The signals are generated by nodes on the CAN BUS. The nodes generate, consume, or both generate
and consume data over a CAN Bus. The CAN High signal is a mirror image of the CAN Low signal.
Adequate voltage supply is required for power to the sensor and all nodes on the CAN Bus. A common
source of problems over a CAN Bus is a Voltage drop because of resistance when a connection is
corroded. As resistance increases, a corresponding voltage drop occurs corrupting the signal generat-
ed. The CAN signal will begin to lose the top of the high signal and no longer mirror the reflection (pari-
ty) of the CAN low signal.
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
57/76
HIRSCHMANN MCS
NOTE
See Appendix for System Layout
You can verify that power is being supplied to the sensor by testing the CAN connectors per this layout:
Connector M12, 5 contacts
Pin Layout (CiA DR-303-1 7.2)
(Female Sockets shown)
Pin 1 Shield
Pin 2 + Ub
Pin 3 Ground
Pin 4 CAN High
Pin 5 CAN Low
Connector M12, 5 contacts
Pin Layout (CiA DR-303-1 7.2)
(Solid for Male Pins)
(Hollow for Female Sockets)
Pin 1 Shield
Pin 2 + Ub
Pin 3 Ground
Pin 4 CAN High
Pin 5 CAN Low
Male Female
(Pins) (Sockets)
Measure between pins 3 and 2 for crane voltage. If you see voltage, check all pins for continuity.
X1 Pin CAN
1 CAN_SHLD 2 CAN +UB 3 CAN GND 4 CAN_H 5 CAN_L
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
58/76
HIRSCHMANN MCS
6.11 Troubleshooting Sensors With Display
The status of all inputs and outputs of the system can be checked using several screen displays on the
console.
6.11.1 Readings of CAN Bus Sensors
To determine whether there is a problem with a sensor, the system has a built in “Analog Input” screen
to make trouble-shooting easier. This is the place to start if you suspect a problem with a sensor.
HOME SETTINGS MACHINE INFO
ANALOG INPUTS
The Analog Inputs screen shows the current readings from each Analog Sensor. The raw value is displayed on the left and the measured value is displayed on the right.
If any problems are detected with a sensor an error icon will appear in the box to the right:
Short to Ground Open Circuit Short to Battery
Not Calibrated Deactivated Response Timeout No Signal From Sensor
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
59/76
HIRSCHMANN MCS
6.11.2 Readings of Digital Inputs
To determine whether there is a problem with a digital input, the system has a built in “Digital Input”
screen to make trouble-shooting easier.
HOME SETTINGS MACHINE INFO
DIGITAL INPUTS
The Digital Inputs screen shows the current readings from each Digital Sensor.
The colored box on the left indicates the status of the input.
Red for Low.
Green for High.
If any problems are detected with the input an error icon will appear in the box to the right:
Short to Ground Open Circuit Short to Battery
Not Calibrated Deactivated Response Timeout No Signal From Sensor
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
60/76
HIRSCHMANN MCS
6.11.3 Readings of Digital Outputs
To determine whether there is a problem with a digital output, the system has a built in “Digital Output”
screen to make trouble-shooting easier.
HOME SETTINGS MACHINE INFO
DIGITAL OUTPUTS
The Digital Outputs screen shows the current values from each Output.
The colored box on the left indicates the status of the output.
Red for Low.
Green for High.
If any problems are detected with the output an error icon will appear in the box to the right
Short to Ground Open Circuit Short to Battery
Not Calibrated Deactivated Response Timeout
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
61/76
HIRSCHMANN MCS
7 Appendix
This appendix contains additional technical information and the full table of error codes.
7.1 Technical Data
Operating voltage 9…36 V DC,
suitable for 12 and/or 24 V on-board power supply
Overvoltage protection overvoltage up to max. 48V DC / 2 minutes
Reverse polarity protection up to -48V DC
Display 4.3“ TFT Color Graphic LCD, 480 x 272 Pixel (WVGA) Or 7“ TFT Color Graphic LCD, 800 x 480 Pixel (WVGA)
Brightness 400 cd/m²
Contrast 400:1 or 500:1
Illumination LED, adjustable brightness
Audible alarm built-in, output for external horn
Dimensions See drawings below.
Operating temperature range -40ºC to +75ºC
Protection class IP66 and IP67 according to ISO 20653: Road Vehicles – Degrees of
protection (IP-Code) – Protection of electrical equipment against for-eign
objects, water and access
Scope of supply - vSCALE D2 / D3 maestro console (depending on scope
of delivery with pre-fitted bracket for RAM Mount)
- Mount articulated mounting
- User manual (PDF file or on data storage device)
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
62/76
HIRSCHMANN MCS
7.2 System Layout Drawing
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
63/76
HIRSCHMANN MCS
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
64/76
HIRSCHMANN MCS
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
65/76
HIRSCHMANN MCS
7.3 Junction Box Wiring Diagram
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
66/76
HIRSCHMANN MCS
7.4 vSCALE D2 Diagram
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
67/76
HIRSCHMANN MCS
7.5 vSCALE D3 Diagram
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
68/76
HIRSCHMANN MCS
7.6 Error Codes Table
The first one or two digits of an error code can determine what type of error is occurring
00xx
General Error
Other
2xxx Module Error
3xxx Module Error
1Fxx System
01xx
Limiter Error
Global Cut
02xx Single Cut
03xx Error
04xx Warning
05xx Pre-Warning
0Axx Kinematic Error
Kinematic
0Bxx Kinematic
11xx
Parameter Errors
Cable Break / Lower Limit
12xx Short-Circuit to Ground
13xx Short-Circuit / Upper Limit
14xx Module Error
15xx Output Deactivated
16xx Sensor Supply Voltage Error
17xx Data Error / CAN Error
18xx Timeout / CAN Timeout
19xx Safety Error
1Axx Parameter Error
1Bxx Unspecified Error
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
69/76
HIRSCHMANN MCS
Error Code Description Solution
Limiter Errors 0100 – 05FF
E0100 Min radius limit underrun (global cut) Boom down to a valid load-chart radius and angle
E0101 Max radius limit exceeded (global cut) Boom up to a valid load-chart radius and angle
E0102 Main boom angle too low (global cut) Boom up to a valid load-chart radius and angle
E0103 Main boom angle too high (global cut) Boom down to a valid load-chart radius and angle
E0104 Jib angle limit underrun (global cut) Move the jib up to a load chart permissible radius or angle
E0105 Jib angle limit exceeded (global cut) Move the jib down to a load chart permissible radius or angle
E010A Slew angle left to large (global cut) Return to the permitted Working Range (load chart)
E010B Slew angle right to large (global cut) Return to the permitted Working Range (load chart)
E010C Min length limit underrun (global cut) Telescope into the permitted Working Range (load chart)
E010D Max length limit exceeded (global cut) Telescope into the permitted Working Range (load chart)
E010E Min height limit underrun (global cut) Move the boom into the permitted Working Range (load chart)
E010F Max height limit exceeded (global cut) Move the boom into the permitted Working Range (load chart)
E012D Max length limit exceeded (global cut) Telescope into the permitted Working Range (load chart)
E0140 Min radius limit underrun (global cut) Move the Jib down to a valid radius and angle
E0141 Max radius limit exceeded (global cut) Boom up to a valid radius and angle
E0142 Main boom angle too low (global cut) Boom up to a valid radius and angle
E0143 Main boom angle too high (global cut) Move the Jib down to a valid radius and angle
E0144 Jib angle limit underrun (global cut) Move the jib up to a valid radius or angle
E0145 Jib angle limit exceeded (global cut) Move the jib down to a valid radius or angle
E0146 Jib angle limit underrun (global cut) Move the jib up to a valid radius or angle
E0147 Jib angle limit exceeded (global cut) Move the jib down to a valid radius or angle
E014A Slew angle left to large (global cut) Rotate to the permitted Working Range
E014B Slew angle right to large (global cut) Rotate to the permitted Working Range
E014C Min length limit underrun (global cut) Telescope into the permitted Working Range
E014D Max length limit exceeded (global cut) Telescope into the permitted Working Range
E014E Min height limit underrun (global cut) Move the boom into the permitted Working Range (load chart)
E014F Max height limit exceeded (global cut) Move the boom into the permitted Working Range
E0150 Min wind speed limit underrun (global cut) Operation is restricted to permitted conditions
E0151 Max wind speed limit exceeded (global cut) Operation is restricted to permitted conditions
E0411 Max wind speed limit exceeded (Warning) Operation is restricted to permitted conditions (load chart)
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
70/76
HIRSCHMANN MCS
Error Code Description Solution
Kinematic Errors 0A00 – 0AFF
E0A00 Capacity utilization >= 100% Lay down the load. Only operate within allowed parameters
E0A08 Capacity utilization >= 90% Warning: Operating close to Cut-off
E0A20 Shutdown due to overload Lay down the load. Only operate within allowed parameters
E0A21 Overload Warning Warning: Operating close to Cut-off
E0A24 A2B switch Lower the load
E0A33 System Bypass Warning: Load monitoring inactive
E0A35 Bypass A2B switch Warning: Load Lift not monitored
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
71/76
HIRSCHMANN MCS
Error Code Description Solution
Sensor & I/O Errors 1100 – 1BFF
E1X00 Sensor Error: IOLength1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X01 Sensor Error: IOAngle1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X02 Sensor Error: IOPiston1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X03 Sensor Error: IORod1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X04 Sensor Error: IOLength2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X05 Sensor Error: IOAngle2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X06 Sensor Error: IOPiston2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X07 Sensor Error: IORod2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X18 Sensor Error: IOInput1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X19 Sensor Error: IOInput2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1A Sensor Error: IOInput3 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1B Sensor Error: IOInput4 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1C Sensor Error: IOInput5 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1D Sensor Error: IOInput6 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1E Sensor Error: IOInput7 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X1F Sensor Error: IOInput8 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X20 Sensor Error: IOForce1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X21 Sensor Error: IOForce2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X28 Sensor Error: IOSlew1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X2C Sensor Error: IOMAngle1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X2D Sensor Error: IOMAngle2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X2E Sensor Error: IOMAngle3 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X2F Sensor Error: IOMAngle4 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
72/76
HIRSCHMANN MCS
Error Code Description Solution
E1X34 Sensor Error: IOWind1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X38 Sensor Error: IOIncX1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X39 Sensor Error: IOIncY1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X3C Sensor Error: IOMaxA2B1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X44 Sensor Error: IOCutByp1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X61 Actuator Error: IOCut Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X63 Actuator Error: IORigging Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X6C Actuator Error: IOLampGreen Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X6D Actuator Error: IOLampYellow Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X6E Actuator Error: IOLampRed Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X7E Actuator Error: IOOutput1 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X7F Actuator Error: IOOutput2 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
E1X80 Actuator Error: IOOutput3 Check the CAN connections and wiring, the sensor calibration, and the CAN configuration. Replace faulty sensor
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
73/76
HIRSCHMANN MCS
Error Code Description Solution
General Errors
E0090 Operating mode changed Not Available
E00FC Controller Not Initialized The error will clear when the system finishes the initialization process
E1F00 System Error Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F01 Timeout Check the bus cabling or connector. Try turning the Ignition off and on again. Consult Customer Service if the error occurs again
E1F02 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F03 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F04 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F05 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F06 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F07 Timeout Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F10 Computer operation error Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E1F18 Serial Number wrong or not set Set Serial Number to valid entry
E1F1F Outputs deactivated Information: Subsequent errors resulting from another system error
E1F2F Outputs deactivated Information: Subsequent errors resulting from another system error
E1F41 Battery voltage Call Customer Service to have the unit replaced
E1F44 CAN bus network error Check the CAN cabling and supply voltage. Try turning the Ignition off and on again. Consult Customer Service if the error occurs again
E1F4F Version Error Call Customer Service to have the unit or software replaced
E2001 Module Error Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E2005 Module Error Turn the Ignition off and on again. Consult Customer Service if the error occurs again
E2015 Module Error Select a valid Operating Mode
E3001 Module Error Turn the Ignition off and on again. Consult Customer Service if the error occurs again
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
74/76
HIRSCHMANN MCS
Feedback What is your opinion about this manual? We always try to describe the products fully in our manuals, as
well as providing important background knowledge to ensure trouble-free operation.
We take the task of continuous improvement and reduction of errors very seriously. Your comments
and suggestions help us to increase the quality and level of information for this document.
Your assessment of this manual:
excellent good satisfactory so-so poor
Accuracy O O O O O
Readability O O O O O
Comprehensibility O O O O O
Examples O O O O O
Structure / Layout O O O O O
Completeness O O O O O
Illustrations / Images O O O O O
Drawings, Diagrams O O O O O
Tables O O O O O
Did you discover errors in this manual?
If so, on which page?
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
75/76
HIRSCHMANN MCS
Suggestions for improvement and additional information:
General comments:
Sender:
Company / Department
Name / Phone
Street
Zip code / City
Date / Signature
Dear user,
please complete and return both pages of this feedback:
via Fax an: +49 (0)7243 709 3222
via Post an: WIKA Mobile Control LP Documentation Hertzstr. 32-34 76275 Ettlingen
Thank You !
WIKA Mobile Control LP 1540 Orchard Drive Chambersburg, PA 17201
qSCALE maestro (PLC v01.00.00) Service Manual / Issue E (HMI v1.0.0) 04/2018 / rbm.
Service : (717) 217-2250 Parts / Sales : (717) 217-2269
www.wika-mc.com
76/76
HIRSCHMANN MCS
Notes