FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A · 2013-02-13 · EN 60947-1, -3 Approval marks...
Transcript of FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A · 2013-02-13 · EN 60947-1, -3 Approval marks...
It is equipped with a label for description of the protected circuit.
Measuring holes in the cover. Basic design with terminal screws M12/28 Nm for cable
lugs max. ø 44 mm and busbars of width max. 40 mm.Connecting sets with terminal inbus screws.Variability of connecting sets including rear connection.It is possible to lock the switch-disconnector cover.
Mounting: Directly on the panel by means of screws.
On busbars with spacing 60 mm by means of adapter.More switch-disconnectors “side-by-side” or “fl at” can be installed without limitation of electrical parameters.Bottom connection is possible without limitation of electric parameters ( the device should be marked „ATTENTION, BOTTOM CONNECTION“).
Fuse switch-disconnector FH3 is intended for fuse-links with blade contacts size 3. It enables safe disconnection not only of rated current, but also overcurrent up to octuple rated current.
A version of this switch-disconnector enables remote signalling of fuse-state, in each pole separately. For signalling of fuse state is used standard visual status indicators of the fuse-links with blade contacts.
Fuse switch-disconnectors up to 630 A
Type Product code Design Weight
[kg]Package
[pcs]
FH3-1A/F 14374 1-pole, design with terminal screws M12 1.710 1
FH3-1S/F 143761-pole, with fuse state signalling, connector with a 1 m cable,
design with terminal screws M12, switch-disconnector cover with signalling can be ordered as a spare part
11.722
FH3-3A/F 14373 3-pole, design with terminal screws M12 4.280 1
FH3-3S/F 143753-pole, with fuse state signalling, connector with 1 m cable,
design with terminal screws M12, switch-disconnector cover with signalling can be ordered as a spare part
14.295
FH3-3SB/F 143773-pole, with fuse state signalling, connector without cable,
design with terminal screws M12, this version enables any connection according to the user needs
14.290
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
Fuse switch-disconnectors
E27
FH3-3L/F 207713-pole, design with terminal screws M12,
with light indication of fuse state, fuse blowing is signalled by fl ashing red LED, if the fuse is not blown, the red LED does not light
4.300 1
Connecting sets
Description Type Product code
Weight[kg]
Package[pcs]
Prismatic clamp for 1-pole switch-disconnector FH3-1./F, connection of Cu/Al conductors of cross-section 120 ÷ 300 mm2, torque 10 Nm
CS-FH3-1P1 15800 0.145 1
Double prismatic looping clamp for 1-pole switch-disconnector FH3-1./F, connection of Cu/Al conductors of cross-section 2 x 120 ÷ 240 mm2, torque 10 Nm
CS-FH3-1P2 15801 0.205 1
Terminal for rear connection for 1-pole switch-disconnector FH3-1./F,CS-FH123-1Z 15594 0.173 1
torquet 20 Nm
Prismatic clamps - set of 3 pcs, for 3-pole switch-disconnector FH3-3./F, connection of Cu/Al conductors of cross-section 120 ÷ 300 mm2, torque 10 Nm
CS-FH3-3P1 14384 0.435 1
Double prismatic looping clamps - set of 3 pcs, for 3-pole switch-disconnector FH3-3./F, connection of Cu/Al conductors of cross-section 2 x 120 ÷ 240 mm2, torque 10 Nm
CS-FH3-3P2 14385 0.615 1
Terminals for rear connection - set of 3 pcs, for 3-pole switch-disconnector FH3-3./F, torque 20 Nm
CS-FH123-3Z 18229 0.520 1
Description Type Product code
Weight [kg]
Package [pcs]
Locking insert for locking the fuse switch-disconnector cover for FH3-1... and FH3-3..., max. diameter of the padlock suspension loop is 4.5 mm, the padlock is not included in the delivery
OD-FH123-VU 18230 0.006 1
Remote signalling of cover position “closed” for FH3-1... and FH3-3..., cable length 1 m, possibility of mounting up to 2 microswitches per one switch-disconnector
OD-FH-SK 12929 0.031 1
Assembly kit for assembling 2-pole or 4-pole switch-disconnector OD-FH123-SS24 17266 0.060 1
Accessories
E28
Fuse switch-disconnectors
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
Accessories
Connecting space cover, identical for both upper and lower space, for 1-pole switch-disconnector FH3-1./F, it is possible to connect more covers in series
OD-FH3-KP1 14388 0.075 1
Connecting space cover, identical for both upper and lower space, for 3-pole switch-disconnector FH3-3./F, it is possible to connect more covers in series
OD-FH3-KP3 14387 0.210 1
Barrier for FH3-3... OD-FH3-Z3 14390 0.045 1
Front shield for FH3-3... OD-FH3-KR 14386 0.036 1
Description Type Product code
Weight [kg]
Package [pcs]
Adapter for busbars with spacing 60 mm, busbar thickness 5 ÷ 12 mm, busbar width 12 ÷ 32 mm, for 3-pole switch-disconnector FH3-3./F, cable outlet bottom or top
OD-FH3-AL60 19557 11.600
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
Fuse switch-disconnectors
E29
Spare parts
Description Type Product code
Weight[kg]
Package [pcs]
Cover without signalling of fuse state, 1-pole, size 000 ND-FH3-V1 33728 0.342 1
Cover without signalling of fuse state, 3-pole, size 000 ND-FH3-V3 33727 0.932 1
Cover with signalling of fuse state, 1-pole, includes a cable with connector ND-FH3-VS1 18686 0.358 1
Cover with signalling of fuse state, 3-pole, includes a cable with connector ND-FH3-VS3 18687 0.967 1
Cover with light indication of fuse state, 3-pole ND-FH3-VL3 33513 1.008 1Connector for 1-pole switch-disconnector with remote signalling of fuse state, without cable, with 3 pins
ND-FH-SZ10 33519 0.028 1
Connector for 1-pole switch-disconnector with remote signalling of fuse state, with 3-core cable
ND-FH-SZ13 33520 0.045 1
Connector for 3-pole switch-disconnector with remote signalling of fuse state, without cable, with 9 pins
ND-FH-SZ30 33521 0.038 1
Connector for 3-pole switch-disconnector with remote signalling of fuse state, with 9-core cable
ND-FH-SZ39 33522 0.055 1
Type FH3
Rated operating voltage (a.c./d.c.) Ue
690 V (400V / FH3-3L/.)
Rated operating current Ie 630 A
Utilization category *
400 V a.c./FH3-1./F AC-23B500 V a.c./FH3-3./F AC-23B
690 V a.c. AC-22B2-pole connection 440 V d.c./FH3-3... DC-21B1-pole connection 440 V d.c./300 A/FH3-1... DC-21B
Rated thermal current with disconnecting link Ith
750 A1000 A
Rated frequency fn 40 ÷ 60 HzRated insulation voltage Ui 1000 V a.c.
Rated conditional short-circuit current (rms) Icc
400 V a.c./630 A 120 kA500 V a.c./630 A 50 kA690 V a.c./500 A 40 kA690 V a.c./630 A min. 25 kA
Rated pulse withstand voltage Uimp
12 kV / FH3-.A/.6 kV / FH3-.S/.
12 kV / FH3-3L/.Rated short-time withstand current Icw 1 s 20 kARated short-circuit making capacity at 400 V a.c. Icm 30 kAMax. power losses of the fuse-link Pv 48 WPower losses at In without fuse-link Pv 49 WElectrical endurance operating cycles 200 at 630 AMechanical endurance operating cycles 800Degree of protection from front side, built-in device, cover closed
IP 30(without measuring holes broken off )Degree of protection from front side, built-in device, cover opened or removed IP 20
Operating ambient temperature - 25 ÷ + 55 °CMax. sea level 2000 mPollution degree 3Overvoltage category for 690 V a.c. IVSeismic resistance according to VE ŠKODA 0.25 ÷ 50 Hz/3g
Standards IEC 60947-1, -3EN 60947-1, -3
Approval marks
Parameters
DimensionsFH3-3A/F and FH3-3L/F FH3-1A/F FH3-3A/F and FH3-3L/F
286
416
257
44
56
416
286
93
8080
40
31
8282
4
E30
Fuse switch-disconnectors
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
* In case of use disconnecting links ZP3 in the switch-disconnectors, the utilization category is decreased by one degree.
ZP3ZP3/1000
FH3-3S/F a FH3-1S/F
FH3-3A/F, FH3-1A/F a nd FH3-3L/F FH3-3A/F, FH3-1A/F and FH3-3L/F
FH3-3...
Dimensions
OD-FH3-KP.
152
416 256
359
95156
169
184
62
214
*
**
***
345
256
73°
171
OD-FH3-KP.* for FH3-1A/F= 78°** for FH3-1A/F= 358*** for FH3-1A/F=304
* for FH3-1S/F= 78°** for FH3-1S/F= 358*** for FH3-1S/F=349
95
256
73°
303
359
*
**
***
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
Fuse switch-disconnectors
E31
5010
3
256
30 30 63 30
256
31.531.5 80160
116
25
116
25
116
25
11
1113
48.5 30
257
35018693
256
ø ø 11
øø
Dimensions
Diagram
Clearance and drilling diagrams
Remote signalling of cover position of 1-pole and 3-pole switch-disconnectors
State of contacts with closed cover:contacts C – NO closed
Remote signalling of fuse state in 1-pole fuse switch-disconnector
State of contacts with not blown fuse:contacts 1 – 3 closed
Remote signalling of fuse state in 3-pole fuse switch-disconnector
State of contacts with not blown fuse:contacts 1 – 7, 2 – 8, 3 - 9 closed
(yellow)
(blue)
(white)
5 A/250 V a.c. 0.2 A/250 V d.c.
5 A/250 V a.c. 0.2 A/250 V d.c.
5 A/250 V a.c. 0.2 A/250 V d.c.
E32
Fuse switch-disconnectors
FUSE SWITCH-DISCONNECTORS SIZE 3 UP TO 630 A
Light indication of fuse state in 3-pole fuse switch-disconnector
Fuse blowing is signalled by fl ashing red LED, if the fuse is not blown, the red LED does not light.
Rated voltage24 - 400 V a.c.24 - 450 V d.c.
2-pole connection of 3-pole fuse switch-disconnector for DC application, see Utilization category
1-pole connection of two 1-pole fuse switch-disconnectors for DC applications, see Utilization category
1–pole 2–pole 4–pole
+
-
-+
J4
Technical information
MINIMAL CONNECTING CROSS-SECTION OF FUSE SWITCH-DISCONNECTORS
Minimal connecting cross-section of cables and busbars of fuse switch-disconnectors and fuse rails
Fuse-links In [A]
Fuse switch-disconnectors and fuse-rails Cable S [mm2]
Busbarw x h
FH000 FH00 FH1 FH2 FH3FD00 FD1 FD2 FD3
FR00 FR1 FR2 FR3 Cu Al Cu Al
4 x x x 1 - - -6 x x x x x 1 - - -8 x x x x x 1 - - -
10 x x x x x 1.5 - - -12 x x x x x 1.5 - - -16 x x x x x 2.5 - - -20 x x x x x 2.5 - - -25 x x x x x 4 - - -32 x x x x x x x 4 - - -35 x x x x x x x 6 - - -40 x x x x x x x 10 - - -50 x x x x x x x 10 16 - -63 x x x x x x x 16 25 - -80 x x x x x x x x x 25 35 - -
100 x x x x x x x x x 35 50 20 x 2 25 x 2125 x x x x x x x x x 50 70 25 x 2 25 x 3160 x x x x x x x x x 70 95 25 x 3 25 x 4200 x x x x x x 95 120 25 x 4 25 x 5224 x x x x x x 95 120 25 x 4 25 x 5250 x x x x x x 120 150 25 x 5 25 x 6315 x x x x 150 185 32 x 5 32 x 6350 x x x x 185 240 32 x 6 32 x 8400 x x x x 240 2x 150 32 x 8 40 x 8500 x x 2x 150 2x 185 2x 30 x 5 2x 40 x 5630 x x 2x 185 2x 240 2x 40 x 5 2x 40 x 8
Note:1) Applies to ambient temperature of swich-disconnectors max. 40 °C2) Applies to HRC fuse-links PLN, PN, PHN
Minimal connecting cross-section of cables of fuse switch-disconnectors for cylindrical fuse-links
Fuse-links In [A]
Fuse switch-disconnectors for cylindrical fuse-links Cable
S [mm2]OPV10 OPV14 OPV22
Cu Al0.25 x x 1 -0.5 x x 1 -1 x x 1 -2 x x 1 -4 x x 1 -6 x x 1 -8 x x 1 -
10 x x 1.5 -12 x x 1.5 -16 x x x 2.5 -20 x x x 2.5 -25 x x x 4 -32 x x x 4 -40 x x 10 -50 x x 10 1663 x x 16 2580 x 25 35
100 x 35 50125 x 50 70
Note:1) Applies to ambient temperature of swich-disconnectors max. 40 °C2) Applies to HRC fuse-links PV10, PV14, PV22