compa_wcdma_ihspa-0900d80580a21658

5/22/2018 compa_wcdma_ihspa-0900d80580a21658

1/46

WCDMA RAN, Rel. RU40,

Operating Documentation,Issue 05

WCDMA RAN Compatibility

DN70140703Issue 06B

Approval Date 2013-09-13


2/46

The information in this document is subject to change without notice and describes only the product

defined in the introduction of this documentation. This documentation is intended for the use of

Nokia Solutions and Networks customers only for the purposes of the agreement under which thedocument is submitted, and no part of it may be used, reproduced, modified or transmitted in any

form or means without the prior written permission of Nokia Solutions and Networks. The documen-

tation has been prepared to be used by professional and properly trained personnel, and the cus-

tomer assumes full responsibility when using it. Nokia Solutions and Networks welcomes customer

comments as part of the process of continuous development and improvement of the documenta-

tion.

The information or statements given in this documentation concerning the suitability, capacity, or

performance of the mentioned hardware or software products are given "as is" and all liability aris-

ing in connection with such hardware or software products shall be defined conclusively and finally

in a separate agreement between Nokia Solutions and Networks and the customer. However,

Nokia Solutions and Networks has made all reasonable efforts to ensure that the instructions con-

tained in the document are adequate and free of material errors and omissions. Nokia Solutions

and Networks will, if deemed necessary by Nokia Solutions and Networks, explain issues which

may not be covered by the document.

Nokia Solutions and Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL Nokia Solutions and Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-

TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-

RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO

LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DA-

TA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other

intellectual property rights according to the applicable laws.

NSN is a trademark of Nokia Solutions and Networks. Nokia is a registered trademark of Nokia

Corporation. Other product names mentioned in this document may be trademarks of their respec-

tive owners, and they are mentioned for identification purposes only.

Copyright Nokia Solutions and Networks 2013. All rights reserved

f Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of

danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the Legal, Safety

and Environmental Information part of this document or documentation set.

Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of

its products and services. We would like to encourage you as our customers and users to join us in

working towards a cleaner, safer environment. Please recycle product packaging and follow the

recommendations for power use and proper disposal of our products and their components.

If you should have questions regarding our Environmental Policy or any of the environmental ser-

vices we offer, please contact us at Nokia Solutions and Networks for any additional information.


2 DN70140703 Issue: 06B


3/46

Table of Contents

This document has 46 pages

Summary of changes..................................................................... 6

1 Compatibility in WCDMA RAN....................................................... 7

2 Standardization compatibility......................................................... 9

2.1 Change requests............................................................................9

2.2 3GPP statement of compliance....................................................27

3 Network compatibility matrix........................................................ 28

3.1 RU30 compatibility....................................................................... 28

3.2 Flexi Direct RU30 compatibility.................................................... 353.3 RU40 compatibility....................................................................... 37

3.4 Flexi Direct RU40 compatibility.................................................... 44


Issue: 06B DN70140703 3


4/46

List of FiguresFigure 1 Radio access network architecture.......................................................7


4 DN70140703 Issue: 06B


5/46

List of TablesTable 1 RU30 system product......................................................................... 28

Table 2 RU30 compatibility with core networks and other systems................ 34Table 3 Compatibility of network elements that belong to Flexi Direct RU30..35

Table 4 Compatibility of network elements that do not belong to Flexi DirectRU30.................................................................................................. 36

Table 5 RU40 system product......................................................................... 37

Table 6 RU40 compatibility with core networks and other systems................ 43

Table 7 Compatibility of network elements that belong to Flexi Direct RU40..44

Table 8 Compatibility of network elements that do not belong to Flexi DirectRU40.................................................................................................. 45


Issue: 06B DN70140703 5


6/46

Summary of changes

Changes between document issues are cumulative. Therefore, the latest document

issue contains all changes made to previous issues.

Changes between issues 06A (2013-05-27, RU40) and 06B (2013-09-13, RU40)

Standardization compatibility

Section Change requests has been modified: CR list has been updated.

Network compatibility matrix

The compatibility information on IPA-RNC, mcRNC, and OMS has been updated inTable 5 RU40 system product.

The compatibility information on MSC Server, OMS, BTS Flexi, and LTE has beenupdated in Table 7 Compatibility of network elements that belong to Flexi DirectRU40.

The compatibility information on BSC has been updated in Table 8 Compatibility ofnetwork elements that do not belong to Flexi Direct RU40.

Changes between issues 06 (2013-03-20, RU40) and 06A (2013-05-27,RU40)


The compatibility information on BTS Flexi has been added to Table 8 Compatibilityof network elements that do not belong to Flexi Direct RU40.

Changes between issues 06 DRAFT (2012-12-05, RU40) and 06 (2013-03-20, RU40)


The compatibility information on BTS Flexi has been added to Table 8 Compatibilityof network elements that do not belong to Flexi Direct RU40.

The compatibility information on IPA-RNC, mcRNC, and OMS has been updated inTable 5 RU40 system product.

The compatibility information on MGW, MSC, and SGSN has been updated in Table6 RU40 compatibility with core networks and other systems

The compatibility information on OMS and LTE has been updated in Table 7Compatibility of network elements that belong to Flexi Direct RU40.

The compatibility information on Flexi ISN has been updated in Table 8 Compatibilityof network elements that do not belong to Flexi Direct RU40.

Summary of changes WCDMA RAN Compatibility

6 DN70140703 Issue: 06B


7/46

1 Compatibility in WCDMA RAN

TheWCDMA

RAN

has3GPP

-standardized interfaces between3G

subsystems, which

allows the operators to continue their existing 2G and 3G supplier policy if they wish to

do so. Depending on the operator's requirements, NSN supplies individual network

elements (NEs) or a complete turnkey system.

3G network architecture is presented in Figure 1: Radio access network architecture.

Both radio access network (RAN) and core network (CN) are illustrated in the figure to

show the relation between them. The figure is a logical representation of the network

elements, interfaces, and their relations in the integrated network.

Figure 1 Radio access network architecture

The compatibility of a release or system product guarantees the following:

WCDMA RAN Compatibility Compatibility in WCDMA RAN

Issue: 06B DN70140703 7


8/46

New product releases or system products do not hinder the performance of existing

products.

Product releases or system products that have an impact on other NEs work in the

network as planned. New products can be properly installed with other relevant or existing products if

necessary.

The performance of a functionality might depend on several product releases. In such a

case, a number of new product releases need to be installed before the functionality is

fully available.

The idea of compatibility in the context of WCDMA RAN and Flexi Direct covers the

following:

compatibility statements required for standardization purposes

the compatibility of the NSN network, which translates into the compatibility of

releases introducing both RAN and CN elements the compatibility feature with a focus on WCDMA/Flexi Direct RU30 and

WCDMA/Flexi Direct RU40.

For information on upgrade paths, see section Supported upgrade path in document

WCDMA RAN System Upgrade.

Compatibility in WCDMA RAN WCDMA RAN Compatibility

8 DN70140703 Issue: 06B


9/46

2 Standardization compatibility

The WCDMA RU40 system release is based on 3GPP Release 9, 06/2011. Change

requests for 3GPP Releases 7 - 9 can have an impact on RU30 EP1, RU30 EP2 and

RU40 system releases.

2.1 Change requests

RU40 release corresponding to 3GPP Release 9, 06/2011 is compatible with the

following 3GPP change requests (CRs):

Specification

TSG Doc.

CR

Subject

TS 25.104 RP-090553 0329

0330

Correction of local area base station

coexistence spurious emission requirements

TS 25.104 RP-090827 0336 Correction of DPCCH slot format for FRC8

TS 25.133 RP-090827 0991 25.133 Rel-7 CR Clarification of NRPM

computation when MIMO is configured

TS 25.141 RP-090553 0500

0501

Correction of local area base station

coexistence spurious emission requirements

TS 25.141 RP-090827 0514 Correction of DPCCH slot format for FRC8

TS 25.201 RP-080356 0039 Introduction of 64QAM for 1.28 Mcps TDD

HSDPA

TS 25.211 RP-080351 0255 Correction to E-DCH control channel timing

TS 25.211 RP-080672 0256 Introduction of the Enhanced Uplink for

CELL_FACH state

TS 25.211 RP-080986 0259 Removal of a reference to E-AICH

TS 25.211 RP-080989 0257 Introduction of Dual-Cell HSDPA Operation onAdjacent Carriers

TS 25.211 RP-090227 0262 Clarification of ACK transmission in response

to HS-SCCH order

TS 25.211 RP-090227 0263 Clarification of ACK transmission in response

to HS-SCCH order

TS 25.211 RP-090229 0260 Clarifications to S-CPICH usage with MIMO

TS 25.211 RP-090229 0261 Clarifications to S-CPICH usage with MIMO

WCDMA RAN Compatibility Standardization compatibility

Issue: 06B DN70140703 9


10/46

Specification

TSG Doc.

CR

Subject

TS 25.212 RP-070950 0256 HS-SCCH information field mapping for64QAM MIMO

TS 25.212 RP-080146 0261 Correction to RV-coding in case of

simultaneous usage of 64QAM and MIMO

TS 25.212 RP-080349 0264 Clarification of number of HS-PDSCH codes in

HS-SCCH-less operations

TS 25.212 RP-080440 0262 HS-SCCH orders for HS-SCCH-less operation

TS 25.212 RP-080665 0272 Correction to the table name and the quoted

name

TS 25.212 RP-080673 0270 Introduction of HS-PDSCH Serving Cell

Change Enhancements


Change Enhancements

TS 25.212 RP-080989 0267 Introduction of Dual-Cell HSDPA Operation on

Adjacent Carriers

TS 25.212 RP-090228 0274 Correction to the puncturing limit allowed when

UL 4PAM modulation is allowed

TS 25.212 RP-100897 0287 Clarification of uplink frequencies

TS 25.212 RP-090228 0273 Correction to the puncturing limit allowed when

UL 4PAM modulation is allowed

TS 25.213 RP-080439 0093 Range of E-DCH amplitude ratios

TS 25.213 RP-080709 0098 Restricted Beta Factor Combinations for EUL

TS 25.213 RP-080989 0099 Clarification of scrambling codes in dual cell

HSDPA operation

TS 25.213 RP-090238 0101 Correction to DTX bit insertion for MBSFN 16-

QAM

TS 25.213 RP-091161 0105

-1

Clarification of the quantization of E-DPDCH

power offset without E-DPCCH boosting

TS 25.213 RP-100897 0107 Clarification of uplink frequencies

TS 25.214 RP-070948 0476 Removing the constraint that the same HS-

SCCH should be used in contiguous TTIs

TS 25.214 RP-070950 0477 Inclusion of CQI tables for the combination of

64QAM and MIMO

TS 25.214 RP-080143 0480 Correction to UE grant monitoring

Standardization compatibility WCDMA RAN Compatibility

10 DN70140703 Issue: 06B


11/46

Specification

TSG Doc.

CR

Subject

TS 25.214 RP-080350 0482 CPC DTX cycle change clarification

TS 25.214 RP-080351 0492 Correction to E-DCH control channel timing

TS 25.214 RP-080439 0485 Correction to E-DPCCH gain factor calculation

TS 25.214 RP-080440 0483 HS-SCCH orders for HS-SCCH-less operation

TS 25.214 RP-080672 0490 Introduction of the Enhanced Uplink for

CELL_FACH state


Change Enhancements

TS 25.214 RP-080974 0502 Clarification of F-DPCH TPC Combining Rule

of cells in the same RLS

TS 25.214 RP-080974 0506 Correction to the description of CPC

procedures

TS 25.214 RP-080974 0524 Clarification of CQI repetition in case of UE

DTX

TS 25.214 RP-080975 0517 Correction to E-DPDCH gain factor

interpolation in compressed mode

TS 25.214 RP-080975 0523 Correction to E-DPDCH gain factor calculation

TS 25.214 RP-080978 0515 Clarification of NIR setting in CQI mapping

tables

TS 25.214 RP-080979 0509 Typographical error correction in a parameter

name in HS-PDSCH reception

TS 25.214 RP-080986 0504 Corrections in the physical random access

procedure for Enhanced Uplink in CELL_FACH

State and Idle mode

TS 25.214 RP-080986 0513 Support of HS-DPCCH for Enhanced Uplink in

CELL_FACH state


Change Enhancements

TS 25.214 RP-080989 0497 Introduction of Dual-Cell HSDPA Operation on

Adjacent Carriers

TS 25.214 RP-080989 0519 References to CQI tables for DC-HSDPA

TS 25.214 RP-080989 0528 Clarifications to Dual-Cell HSDPA Operation

TS 25.214 RP-080990 0508 Improved EUL power control at UE power

limitation


Issue: 06B DN70140703 11


12/46

Specification

TSG Doc.

CR

Subject

TS 25.214 RP-090227 0530 Editorial correction to UE transmit powercontrol behavior in case of DTX/DRX

TS 25.214 RP-090227 0531 Editorial correction to UE transmit power

control behavior in case of DTX/DRX

TS 25.214 RP-090227 0533 Clarification of CQI preamble length when

switching UE DTX cycle

TS 25.214 RP-090227 0535 Clarification of CQI preamble length when

switching UE DTX cycle

TS 25.214 RP-090229 0538 Clarification of the source of parameters to the

HS-DSCH physical layer

TS 25.214 RP-090229 0540 Clarification of the source of parameters to the

HS-DSCH physical layer

TS 25.214 RP-090242 0534 Corrections of HS-SCCH orders for DC-

HSDPA

TS 25.214 RP-090525 0544 Clarification of the transmission of a

combination of ACK and NACK

TS 25.214 RP-090525 0545 Clarification of the transmission of a

combination of ACK and NACK

TS 25.214 RP-090532 0546 HS-DSCH serving cell change enhancements

with preconfigured secondary cell

TS 25.214 RP-090883 0563 Unequal Power Setting of P-CPICH and S-

CPICH

TS 25.214 RP-090885 0549 Clarification of CQI transmission when CQI

priority changes

TS 25.214 RP-090885 0550 Clarification of CQI transmission when CQI

priority changes

TS 25.214 RP-090885 0556 Clarification of CPC Enabling Delay

TS 25.214 RP-090885 0557 Clarification of CPC Enabling Delay

TS 25.214 RP-090885 0558 Clarification of DTX Cycle transitions and UL

DPCCH burst transmissions

TS 25.214 RP-090885 0559 Clarification of DTX Cycle transitions and UL

DPCCH burst transmissions

TS 25.214 RP-090885 0560 Clarification of the start of the CQI_DTX_Timer

TS 25.214 RP-090885 0561 Clarification of the start of the CQI_DTX_Timer


12 DN70140703 Issue: 06B


13/46

Specification

TSG Doc.

CR

Subject

TS 25.214 RP-090889 0568 HS-DPCCH ACK/NACK Power Offset settingfor DC-HSDPA

TS 25.214 RP-091162 0572

-1

Clarification of HS-SCCH monitoring when

64QAM is configured

TS 25.214 RP-091163 0571

-1

Clarification of CQI nominal timer and CQI DTX

TIMER

TS 25.214 RP-091163 0581 Clarification of CQI nominal timer and CQI DTX

TIMER

TS 25.214 RP-091164 0573

-1

Clarification of HS-SCCH monitoring

TS 25.214 RP-100199 0590

0591

HSDPA MIMO codebook restriction

TS 25.214 RP-100883

R1-104974

R1-104975

R1-104976

0605

(rel7,

F)

0606

(rel8,

A)

0607

(rel9,

A)

Clarification of HS-DSCH and HS-SCCH

reception in CELL_FACH, CELL_PCH and

URA_PCH states (RANimp-EnhState)

TS 25.214 RP-100883

R2-105113

R2-105114

R2-105115

0199

(rel7,

F)

0200

(rel8,

A)

0201

(rel9,

A)

Corrections to physical channel combinations

for Enhanced CELL_FACH state for FDD

TS 25.214 RP-100893

R1-105002

R1-105003

R1-105004

0602

(rel7,

F)

0603

(rel8,

A)

0604

(rel9,

A)

Clarification of the CQI definition when the UE

is configured in MIMO mode (MIMO-Phys)


Issue: 06B DN70140703 13


14/46

Specification

TSG Doc.

CR

Subject

TS 25.214 RP-100894

R1-104154

R1-104155

R1-104156

0612(rel7,

F)

0613

(rel8,

A)

0614

(rel9,

A)

Clarification of E-AGCH/E-RGCH monitoring ina CM gap when DL_DRX_Active is TRUE

(RANimp-CPC)

TS 25.214 RP-101312 0634 Clarification of discontinuous uplink DPCCH

transmission and compressed mode





TS 25.214 RP-101315 0626 Correction of number of received HS-DSCH in

DC-HSDPA-MIMO

TS 25.214 RP-120281 666

(rel8,

F) 667

(rel9,A)

Further clarification of when to use Sync A

procedure when UE transitions from

CELL_FACH to CELL_DCH

TS 25.215 RP-080436 0188 E-UTRA measurements for UTRAE-UTRA

interworking

TS 25.215 RP-080666 0190 Modification of RSRQ and removal of RSSI

TS 25.215 RP-080666 0192 Modification of RSRP definition

TS 25.215 RP-080672 0189 UPH measurement support for Enhanced

Uplink for CELL_FACH state

TS 25.215 RP-090232 0194 RSRP and RSRQ measurement definitions

TS 25.302 RP-080696 0183 Introduction of Enhanced Uplink in

CELL_FACH in 25.302

TS 25.302 RP-081022 0184 Replacement of E-AICH in 25.302

TS 25.302 RP-081025 0185 Introduction of enhanced CELL_FACH,

CELL_PCH, and URA_PCH for 1.28 Mcps

TDD

TS 25.302 RP-090519 0186 Support for 3.84 Mcps MBSFN IMB operation


14 DN70140703 Issue: 06B


15/46

Specification

TSG Doc.

CR

Subject

TS 25.302 RP-100849 0686 Clarification on the use of timer T2 inEnhanced Uplink in CELL_FACH state and Idle

mode for FDD

TS 25.306 RP-090506 0220 Addition of description about the parameter of

Need for Idle Interval

TS 25.306 RP-090519 0223 Clarification of the code rate restriction for

Cat19

TS 25.306 RP-090902 0232 Making features Using special value of HE

field to indicate end of an SDU for RLC AM,

Removing the constraint that the same HS-

SCCH should be used in contiguous TTIs, andso on optional,

TS 25.306 RP-90114 0211 Correction of RF parameters in 25.306

TS 25.306 RP-90114 0212 Correction of RF parameters in 25.306

TS 25.319 RP-111708 0091

(rel8,

F)

0092

(rel9,

F)

Cleanup corrections for enhanced uplink

operation with MAC-i

TS 25.321 RP-090116 0480 Corrections to E-TFC selection in case of E-

DPDCH extrapolation


DPDCH extrapolation

TS 25.321 RP-090116 0483 SI reporting and compressed mode

TS 25.321 RP-090116 0484 SI reporting and compressed mode

TS 25.321 RP-090118 0490 Addition of HARQ procedure for HS-SCCH-

less operation when MAC-ehs is configured

TS 25.321 RP-090118 0501 Correction to HARQ operation for HS-SCCH-

less operation

TS 25.321 RP-090120 0493 Correction to Absolute Grant Value for LCR

TDD

TS 25.321 RP-090120 0506 25.321(R7,F) on correction of E-TFC selection

procedure for LCR TDD


DPDCH extrapolation


Issue: 06B DN70140703 15


16/46

Specification

TSG Doc.

CR

Subject

TS 25.321 RP-090121 0499 Correction to MAC handling of AG and SGtables when 16QAM UL is configured

TS 25.321 RP-090501 0518 Correction to non-scheduled transmission for

1.28 Mcps TDD


1.28 Mcps TDD

TS 25.321 RP-090503 0520 Correction to Improved L2 for 1.28 Mcps TDD

TS 25.321 RP-090503 0521 Correction to Improved L2 for 1.28 Mcps TDD

TS 25.321 RP-090503 0522 Correction to TBS tables for Improved L2 for1.28 Mcps TDD

TS 25.321 RP-090503 0523 Correction to TBS tables for Improved L2 for

1.28 Mcps TDD

TS 25.321 RP-090504 0513 Reordering configuration for BCCH and paging

TS 25.321 RP-090504 0514 Reordering configuration for BCCH and paging

TS 25.321 RP-090505 0524 Clarification to grant monitoring

TS 25.321 RP-090505 0525 Clarification to grant monitoring

TS 25.321 RP-090519 0509 Correction to adding CMAC_STATUS in figure

11.2.2A-3

TS 25.321 RP-090519 0510 Correction to the Scheduling Information

Indication

TS 25.321 RP-090519 0511 HARQ delivery correction

TS 25.321 RP-090519 0512 Correction to HS-DSCH SPS operation for 1.28

Mcps TDD

TS 25.321 RP-090519 0517 MAC-STATUS-Ind for CCCH transmissions

TS 25.321 RP-090902 0546 25.321 Feature to be made optional in release

7: SI trigger when grant 0 - Rel-8 shadow

TS 25.321 RP-091311 0571 TSN or SI field presences in case of

consecutive BCCH/PCCH re-ordering PDUs

TS 25.321 RP-091329 0564 -

1

Clarification on when to include SI in MAC-i

PDU

TS 25.321 RP-091347 0573 Unoptimized usage of the SID, N

representation in MAC-hs header

TS 25.321 RP-100303 0620 Corrections for DC-HSUPA in 25.321


16 DN70140703 Issue: 06B


17/46

Specification

TSG Doc.

CR

Subject

TS 25.321 RP-100303 0635 Clarification on E-TFC selection and happy bitprocedures for DC-HSUPA

TS 25.321 RP-100532 0669 Correction to Mac headers in CELL FACH,

CELL PCH and URA PCH

TS 25.321 RP-100533 0675 Reordering entity for each configured Queue ID

at UE

TS 25.321 RP-100537 0653 Clarification of UE Id handling after collision

resolution

TS 25.321 RP-100849 0700 Corrections for Enhanced Uplink in

CELL_FACH state and idle mode

TS 25.321 RP-121357 0776

(Rel-8,

F)

0777

(Rel-9,

A)

Clarification of CRC parity bits appened to

MAC-c PDUs

TS 25.322 RP-090117 0353 Correction for VR(UM)

TS 25.322 RP-090138 0356 Clarification of the description of the

transmitting UM RLC entity

TS 25.322 RP-090138 0357 Correction to RLC text for MAC i/is

TS 25.322 RP-090140 0354 Concatenation/segmentation in case

SN_Delivery parameter is configured

TS 25.322 RP-090151 0358 Removal of DCCH logical channel mapped on

RLC TM entity

TS 25.322 RP-090909 0368 Clarification to LI setting after Timer_Discard

expiry when alternative e-bit is used

TS 25.322 RP-090917 0366 Clarification on minimum PDU size

TS 25.322 RP-100286 0374 RLC recovery with uplink POLL_SUFI

TS 25.322 RP-100286 0375 RLC recovery with uplink POLL_SUFI

TS 25.322 RP-110770 0390 Accept RLC PDUs with special value HE field if

its supported

TS 25.323 RP-090140 0314 Coding of the PDCP AMR Data PDU payload

TS 25.323 RP-090140 0315 Condition to identify a CS-HSPA configuration


Issue: 06B DN70140703 17


18/46

Specification

TSG Doc.

CR

Subject

TS 25.331 RP-090115 3579 Correction to handling of CELL_INFO_LISTwhen Inter-frequency cell info list is received

in System Information Block Type 11bis

TS 25.331 RP-090115 3534

3533

UMTS frequency information in IE "Rplmn

information"

TS 25.331 RP-090115 3536

3537

CN system information after PS HO

TS 25.331 RP-090115 3581

3582

Corrections to PS handover to UTRAN

TS 25.331 RP-090117 3541 Condition to set the Security capability

indication flag

TS 25.331 RP-090117 3543 Ciphering for intra-UTRAN Radio Bearer Setup

- Rel 7

TS 25.331 RP-090117 3574 25.331 Rel 7 CR UE restrictions on E-TFCI

TS 25.331 RP-090117 3621 Adding the MBMS PTM RB release cause in

the MCCH message when releasing the MBMS

service for 1.28 Mcps TDD

TS 25.331 RP-090118 3568 Clarification of scope of signaled transport

block sizes for HS-SCCH-less operation

TS 25.331 RP-090118 3586 Correction to handling of DTX-DRX information

TS 25.331 RP-090119 3539 Correction to the UE behavior when entering

URA_PCH state

TS 25.331 RP-090121 3584 Correction to RRC handling of AG and SG

tables when 16QAM UL is configured

TS 25.331 RP-090122 3616 Clarification of 64QAM TB Table applicability

TS 25.331 RP-090498 3627

3628

Removal of description of CPCH feature

TS 25.331 RP-090499 3669

3670

Clarification of the support of 2 different layer 3

filters per measurement type

TS 25.331 RP-090500 3634 Clarification for setting the

HS_SCCH_LESS_STATUS variable

TS 25.331 RP-090500 3646 Correction to CPC activation/deactivation


18 DN70140703 Issue: 06B


19/46

Specification

TSG Doc.

CR

Subject

TS 25.331 RP-090500 3674 Removal of slot format 3 from IE "UplinkDPCCH slot format information" in "DTX-DRX

information"

TS 25.331 RP-090500 3689 Corrections to CPC when E-DCH TTI is

reconfigured


1.28 Mcps TDD

TS 25.331 RP-090502 3696 Correction to p-t-m bearer release in MBSFN

TS 25.331 RP-090503 3659 Clarification of CQI reporting for 1.28 Mcps

TDD

TS 25.331 RP-090503 3661 Correction to Improved L2 support for high data

rates for TDD

TS 25.331 RP-090504 3682 Correction to Enhanced CELL_FACH

Capability

TS 25.331 RP-090505 3630 Error in UE capability update procedure

TS 25.331 RP-090505 3632 Correction on

deferredMeasurementControlReading

TS 25.331 RP-090505 3644 Correction to UE Mobility State Indicator

TS 25.331 RP-090505 3672 Clarification of handling of IE "Use special

value of HE field"

TS 25.331 RP-090505 3691 Call Type Inclusion condition

TS 25.331 RP-090606 3655 Specification of CPC restored state upon

physical layer failure

TS 25.331 RP-090874 3810 Making features "Absolute priority reselection

to GERAN," "Absolute priority reselection to

UTRA inter-frequency," and "Improved EUL

power control" optional

TS 25.331 RP-09089 3770 CS voice over HSPA UE capability in RRC

CONNECTION REQUEST

TS 25.331 RP-090898 3763 Making features "Two DRX schemes in

URA_PCH and CELL_PCH" and "E-DPDCH

power interpolation formula" optional

TS 25.331 RP-090902 3724 Making features Using special value of HE

field to indicate end of an SDU for RLC AM

and Octet aligned HS-DSCH transport block

sizes for non-64QAM UEs optional


Issue: 06B DN70140703 19


20/46

Specification

TSG Doc.

CR

Subject

TS 25.331 RP-090902 3728 Making features Using special value of HEfield to indicate end of an SDU for RLC AM,

Removing the constraint that the same HS-

SCCH should be used in contiguous TTIs, and

Octet aligned HS-DSCH transport block sizes

for non-64QAM UEs optional

TS 25.331 RP-090902 3758 25.331 Features to be made optional in release

7: F-DPCH, Wait Time to CUC, Using special

value of HE field to indicate end of an SDU for

RLC AM

TS 25.331 RP-090902 3759 25.331 Features to be made optional in release

7: F-DPCH, Wait Time to CUC, Using specialvalue of HE field to indicate end of an SDU for

RLC AM - Rel-8 shadow

TS 25.331 RP-090902 3814 Reformulating the bit of feature "UEA2/UIA2"

TS 25.331 RP-090902 3815 Reformulating the bit of feature "UEA2/UIA2"

TS 25.331 RP-090904 3764 Making features "Two DRX schemes in

URA_PCH and CELL_PCH" and "E-DPDCH

power interpolation formula" optional

TS 25.331 RP-090906 3702 Clarification on signaling connection

initialization upon HO to UTRAN

TS 25.331 RP-090909 3742 Clarification of UE behavior on RLC

unrecoverable error when UE has not received

L2 Ack for a Reconfig Complete message

TS 25.331 RP-090912 3705 Corrections to handling of secondary cell HS-

DSCH information in DC-HSDPA

TS 25.331 RP-090916 3715 Validation of PDCP configuration in case of CS

voice over HSPA

TS 25.331 RP-090916 3738 Correction to response message of Cell

Update Confirm message in case of VoiceType Transition, that is, CS over HSPA to CS

over DCH or vice versa

TS 25.331 RP-090916 3769 CS voice over HSPA UE capability in RRC

CONNECTION REQUEST

TS 25.331 RP-090923 3727 Introduction of Dual Band HSDPA in 25.331

TS 25.331 RP-091312 3855 MAC-es/e reset when 16QAM operation starts

or stops

TS 25.331 RP-091328 3969 CS voice over HSPA SDU discard timer

configuration


20 DN70140703 Issue: 06B


21/46

Specification

TSG Doc.

CR

Subject

TS 25.331 RP-100199 4009 Indication of MIMO codebook restriction

TS 25.331 RP-100199 4010 Indication of MIMO codebook restriction

TS 25.331 RP-100288 4082 Correction of RNTIs handling for Enhanced

Uplink in CELL_FACH

TS 25.331 RP-100288 4083 Correction of RNTIs handling for Enhanced

Uplink in CELL_FACH

TS 25.331 RP-100303 4024 Corrections for virtual active set

TS 25.331 RP-100532 4161 Clarification on the HS-DSCH reception in

enhanced CELL_FACH state

TS 25.331 RP-100537 4126 Clarification of Tx interruption after trigger

handling for Enhanced Uplink in CELL_FACH

state and Idle mode

TS 25.331 RP-110264 4455 PCI Weight set restriction logic

TS 25.331 RP-111274 4729

(rel8,

F)

4730

(rel9,

A)

Clarification on Uplink DPCH power control info

for Common E-DCH

TS 25.331 RP-111274 4773

(rel8,

F)

4774

(rel9,

A)

Use of New E-RNTI in UMI message

TS 25.331 RP-111216 4787 Impliit HARQ memory partitioning for DC MIMO

configurations

TS 25.331 PR-111706 4810

(rel8,F)

4811

(rel9,

A)

Corrections of PS keys handling upon PS

ISHO

TS 25.331 RP-111703 4861

(rel7,

F)

4862

(rel8,

A)

Clarification to the handling of HS-DSCH TB

size table


Issue: 06B DN70140703 21


22/46

Specification

TSG Doc.

CR

Subject

4863(rel9,

F)

TS-25.331 RP-111704 4870

(rel7,

F)

4871

(rel8,

A)

4872

(rel9,

A)

Correction of BCCH mapping on HS-DSCH

TS-25.331 RP-120320 4931 Clarifications of the UE behaviours when

initiatiing a cell update procedure

TS-25.331 RP-130807 1074 Clarification of the security configuration after

simultaneous CS and PS inter-RAT Handover

TS 25.413 RP-090633 0994 Correction of extended alternative bit rate

TS 25.413 RP-090633 0996 Structure of procedure text for Relocation

Preparation

TS 25.413 RP-090635 0998 Interaction between Enhanced Relocation and

RAB Assignment Procedure

TS 25.413 RP-090636 1002 Introduction of E-UTRAN Service Handover IE

TS 25.413 RP-090638 0988 Addition of Integrity Protection Information IE

and Encryption Information IE to Enhanced

SRNS Relocation

TS 25.413 RP-090641 0989 RANAP changes to support paging

optimization

TS 25.413 RP-090642 0999 Correction of introduction of HSPA SRVCC

TS 25.413 RP-090642 1000 Correction of the Global CN-ID for the PSdomain

TS 25.413 RP-090770 1015 Correction of ASN.1 Target Cell ID missing

TS 25.413 RP-90075 0976 Clarification of usage of Extended MBR and

GBR

TS 25.413 RP-130643 1228-

2

Resolution of ambiguity around reject causes in

MOCN

TS 25.413 RP-130643 1234-

2

Redirect indication for NAS rejection cause #17

and #25


22 DN70140703 Issue: 06B


23/46

Specification

TSG Doc.

CR

Subject

TS 25.423 RP-090072 1441 Addition of MAC-hs Reset Indicator IE toRADIO LINK ADDITION FAILURE message

TS 25.423 RP-090072 1451 Addition of F-DPCH Slot Format IE to RADIO

LINK SETUP FAILURE and RADIO LINK

ADDITION FAILURE message

TS 25.423 RP-090073 1467 ASN.1 Correction on Transport Bearer Not

Requested Indicator in RL Specific E-DCH

Information

TS 25.423 RP-090073 1475 Correction of erroneous IE reference

TS 25.423 RP-090074 1438 Addition of Multi-carrier HS-DSCH physicallayer category for 1.28 Mcps TDD

TS 25.423 RP-090074 1445 Addition of DCH Indicator For E-DCH-HSDPA

Operation IE into RADIO LINK CONGESTION

INDICATION message

TS 25.423 RP-090075 1435 Addition of MBR parameter for 1.28 Mcps TDD

Enhanced Uplink

TS 25.423 RP-090577 1508

1509

Correction of MIMO Information Response IE

TS 25.423 RP-090630 1504

1505

Correction of the value range of MAC PDU

Size Extended IE in RNSAP

TS 25.423 RP-090631 1489

1490

Clarification of E-AGCH Table Choice

TS 25.423 RP-090631 1491

1492

Addition of Max UE DTX Cycle into UPLINK

SIGNALLING TRANSFER INDICATION

message

TS 25.423 RP-090633 1498 Correction of indentation

TS 25.423 RP-090633 1499 Inclusion of a general HS-SCCH support

indicator

TS 25.423 RP-090634 1495 Removal of HS-PDSCH Code Change

indicator IE from RADIO LINK PARAMETER

UPDATE INDICATION message

TS 25.423 RP-090634 1500 Correction of tabular for INFORMATION

REPORT message

TS 25.423 RP-090635 1493 Clarification of Uplink L2 improvement


Issue: 06B DN70140703 23


24/46

Specification

TSG Doc.

CR

Subject

TS 25.423 RP-090635 1506 Addition of description for Fixed and FlexibleRLC PDU operation for TDD

TS 25.423 RP-090635 1507 Early Enhanced Relocation Cancel

TS 25.423 RP-090638 1481 Addition of Causes for Enhanced Relocation

Failure

TS 25.423 RP-090638 1484 Further abnormal conditions for IP Transport

Option

TS 25.423 RP-090638 1485 Partial Failure for DC-HSDPA

TS 25.423 RP-090638 1486 Corrections to CPC DRX configuration for 1.28Mcps TDD

TS 25.423 RP-090769 1530 SixtyfourQAM DL Support Indicator

TS 25.423 RP-090770 1515 Correction of E-DCH FDD Information

abnormal condition in radio link reconfiguration

procedure

TS 25.423 RP-090770 1516 Addition of HS-DSCH TB Size Table Indicator

related context at serving HS-DSCH RL

change

TS 25.423 RP-090770 1517 Addition of abnormal condition for HS-DSCH/E-DCH in RL Addition procedure

TS 25.423 RP-090770 1532 Enhanced HS-SCCH support optional in Rel-8

TS 25.423 RP-090770 1533 Addition of cause SixtyfourQAM DL and MIMO

Combined not supported in RL reconfiguration

procedure

TS 25.423 RP-090770 1534 Correction for procedural text for MBMS Bearer

Service List IE

TS 25.423 RP-090770 1535 Inclusion of UE Support Indicator Extension IE

in RL handling

TS 25.423 RP-090771 1511 Correction of ASN.1 for CPC for 1.28 Mcps

TDD

TS 25.423 RP-090846 1538 Rel-7 RNSAP Support for Signaling of S-

CPICH power offset and DL Control Channel

TX Diversity for MIMO UEs

TS 25.423 RP-090847 1539 Rel-8 RNSAP Support for Signaling of S-

CPICH power offset and DL Control Channel

TX Diversity for MIMO UEs


24 DN70140703 Issue: 06B


25/46

Specification

TSG Doc.

CR

Subject

TS 25.425 RP-110681 0156 Correction of Logical Channel ID range used inEnhanced Cell-FACH

TS 25.425 RP-111645 0161 Indicator for DTXDRX HS-SCCH order

TS 25.433 RP-090072 1579 Addition of MAC-hs Reset Indicator IE to

RADIO LINK ADDITION FAILURE message

TS 25.433 RP-090074 1576 Addition of Multi-carrier HS-DSCH physical

layer category for 1.28 Mcps TDD

TS 25.433 RP-090075 1573 Addition of MBR Parameter for 1.28 Mcps TDD

Enhanced Uplink

TS 25.433 RP-090075 1594 Enhancement of MBMS reception with

simultaneous HSDPA for 1.28 Mcps TDD

TS 25.433 RP-090630 1629 Correction of the value range of MAC PDU

Size Extended IE in NBAP

TS 25.433 RP-090630 1630 Correction of the value range of MAC PDU

Size Extended IE in NBAP

TS 25.433 RP-090631 1614 Improved CM checks for F-DPCH

TS 25.433 RP-090631 1615 Improved CM checks for F-DPCH

TS 25.433 RP-090631 1618 Clarification of E-AGCH Table Choice

TS 25.433 RP-090631 1619 Clarification of E-AGCH Table Choice

TS 25.433 RP-090631 1620 Addition of UL 16QAM credit consumption in E-

DCH Capacity Consumption Law

TS 25.433 RP-090631 1621 Addition of UL 16QAM credit consumption in E-

DCH Capacity Consumption Law

TS 25.433 RP-090633 1613 Correction of formatting in NBAP

TS 25.433 RP-090633 1624 ASN.1 correction for MAC-hs Reset Indicator

TS 25.433 RP-090633 1626 Inclusion of a general HS-SCCH support

indicator

TS 25.433 RP-090634 1623 Removal of HS-PDSCH Code Change

indicator IE from RADIO LINK PARAMETER

UPDATE INDICATION message

TS 25.433 RP-090634 1625 Correction of abnormal condition for RL

Addition Request

TS 25.433 RP-090634 1628 Removal of DC-HSDPA limitation from NBAP


Issue: 06B DN70140703 25


26/46

Specification

TSG Doc.

CR

Subject

TS 25.433 RP-090634 1631 Addition of SPI IE in Common E-DCH SystemInformation LCR IE

TS 25.433 RP-090635 1622 Clarification of Uplink L2 improvement

TS 25.433 RP-090635 1632 Addition of description for Fixed and Flexible

RLC PDU operation for TDD

TS 25.433 RP-090638 1605 Corrections to the modification of MIMO

reference signal for 1.28 Mcps TDD

TS 25.433 RP-090638 1608 Further abnormal conditions for IP Transport

Option

TS 25.433 RP-090638 1609 Partial Failure for DC-HSDPA

TS 25.433 RP-090638 1610 Corrections of CPC DRX configuration for 1.28

Mcps TDD

TS 25.433 RP-090769 1656 Addition of Semantics Description for E-DCH

RACH Report Information in Common

Measurement Value

TS 25.433 RP-090769 1661 Clarification of Power Resource Related Info in

TDD non-scheduled grant information

TS 25.433 RP-090769 1664 Corrections related to UE Status Updateprocedure

TS 25.433 RP-090770 1643 Correction of E-DCH FDD Information

abnormal condition in radio link reconfiguration

procedure

TS 25.433 RP-090770 1644 Clarification of E-DCH related resources

assignment in Physical Shared Channel

Reconfiguration procedure

TS 25.433 RP-090770 1645 Addition of abnormal condition for HS-DSCH/E-

DCH in RL Addition procedure

TS 25.433 RP-090770 1657 Semantics Description of IB_OC_ID

TS 25.433 RP-090770 1663 Enhanced HS-SCCH support optional in Rel-8

TS 25.433 RP-090770 1666 Inclusion of UE Support Indicator Extension IE

in RL handling

TS 25.433 RP-090771 1635 Correction of ASN.1 for CPC for 1.28 Mcps

TDD

TS 25.433 RP-090780 1641 Corrections to the common measurement for

1.28 Mcps TDD


26 DN70140703 Issue: 06B


27/46

Specification

TSG Doc.

CR

Subject

TS 25.433 RP-090780 1642 Corrections to the common measurement for1.28 Mcps TDD

TS 25.433 RP-090845 1670 Rel-8 NBAP Support for Signaling of S-CPICH

power offset and DL Control Channel TX

Diversity for MIMO UEs

TS 25.433 RP-090962 1669 Rel-7 NBAP Support for Signaling of S-CPICH

power offset and DL Control Channel TX

Diversity for MIMO UEs

TS 25.433 RP-100545 1819/

1

Correction for Enhanced Serving cell change

TS 25.433 RP-111645 1924/

2

Support of dynamic HS-SCCH order for

DTXDRX

TS 25.435 RP-091179 0208 Correction to the description of HS-DSCH

DATA FRAME TYPE2

TS 25.435 RP-110681 0261 Correction of Logical Channel ID range used in

Enhanced Cell-FACH

TS 25.435 RP-110681 0262 Correction of Logical Channel ID range used in

Enhanced Cell-FACH

TS 25.435 RP-110683 0258 Special value for HS-DSCH DATA FRAMETYPE 2 RACH Measurement Result

TS 25.435 RP-111645 0274 Indicator for DTXDRX HS-SCCH order

TS 25.453 RP-090770 0119 Correction of Cell-ID Measured Results Sets in

INFORMATION EXCHANGE INITIATION

REQUEST

2.2 3GPP statement of compliance

WCDMA RAN Statement of Compliance refers to the following system releases:

WCDMA RU40, supporting 3GPP Release 9, 06/2011

WCDMA RU30 EP2, supporting 3GPP Release 9, 06/2011

WCDMA RU30 EP1, supporting 3GPP Release 9, 03/2011


Issue: 06B DN70140703 27


28/46

3 Network compatibility matrix

Tables 1-8 include supported releases of individual network elements, listed per release.

3.1 RU30 compatibility

Table 1 RU30 system product

Network

element

HW release

SW release

Supports

Note

IPA-RNC

(Radio NetworkController)

IPA 2800

A12

RN6.0 1.x RN5.0

mcRNC2.0

RNC OMS 1.0 1.x

I-HSPA Rel3

Flexi Direct RU 30

RL20

RL30

S14

S15

AXC C6.0

Flexi WN6.0

Flexi WN7.0 1.0

Flexi WN7.0 2.0

Ultra WN6.0

Juniper EX4200 (JUNOS 10.0

S1.1)

Juniper MX series (JUNOS 10.1

R2.8)

Cisco 7600 (IOS 12.2(33)SRD)

Cisco 7600 (IOS 15.0(1)S)

Cisco 7600 (IOS 15.1(2)S1)

Flexipacket MultiRadio Release

2.1

Flexipacket MultiRadio R H1.0

FlexiPacket Hub 800 Release 2.0


FlexiPacket Hub 800 H Release

1.0

compatible with RN6.0 1.x and

RN6.0 2.0

compatible with RN6.0 1.x

compatible with RN6.0 2.0

Network compatibility matrix WCDMA RAN Compatibility

28 DN70140703 Issue: 06B


29/46

Table 1 RU30 system product (Cont.)

Networkelement

HW release

SW release

Supports

Note

FlexiPacket Firstmile 200 1.0

EP1

FlexiPacket Firstmile 200

Release 2.0

IPA-RNC

(Radio Network

Controller)

IPA 2800

A12

RN6.0 1.x

RN6.0 2.0


Release 2.5

FlexiPacket FirstMile 220 H

Release 2.0

Flexi ISN FI4 CD4

Flexi ISN FI50

Flexi ISN FI50 CD2

Flexi NG (GGSN) NG10 CD4


Flexi NG (GGSN) NG2.0

Tellabs 8600 series

OSS5.3 MP1+PCDs/OSS5.3

MP2

OSS5.4 CD Set 1

OSS5.4 CD Set 2

MGW U4.0

MGW U4.1

MGW U4.2

MGW U4.2+EPx

MGW U5.0

MGW U5.0+EPx

M14.6

M15.0

M15.1

M16.0

Flexi NS-SGSN DX SG7.0 CD2





OSS5.3 MP1+PCDs/OSS5.3 MP2

are compatible with RN6.0 1.x.

OSS5.4 CD Set 1 and OSS5.4

CD Set 2 are compatible with

RN6.0 1.x and RN6.0 2.0.OSS5.4 CD Set 2 enhances the

support with updated parameter

descriptions and error corrections.

It is strongly recommended to

take the latest NetAct CD set

available at the time of

deployment.

WCDMA RAN Compatibility Network compatibility matrix

Issue: 06B DN70140703 29


30/46


Networkelement

HW release

SW release

Supports

Note


Flexi NS-SGSN DX SG8.0

Flexi NS-SGSN DX SG8.0 CDx

Flexi NS-SGSN ATCA SG8.0


CDx

Multicontroller

RNC (mcRNC)

BCN Platform mcRNC2.0 RN5.0

RN6.0 1.x

RN6.0 2.0

RNC OMS 1.0 1.x

I-HSPA Rel3

Flexi Direct RU30

RL20

RL30

BSC S14

BSC S15

Flexi WN6.0

Flexi WN7.0 1.0

Flexi WN7.0 2.0

Ultra WN6.0

OSS5.4 CD Set 1

Cisco 7600 (IOS 12.2(33)SRD)


2.1





1.0


EP1


Release 2.0


Release 2.5

ATCA-based


30 DN70140703 Issue: 06B


31/46


Networkelement

HW release

SW release

Supports

Note


Release 2.0

Flexi ISN FI4 CD4

Flexi ISN FI50

Flexi ISN FI50 CD2




MGW U4.2

MGW U4.2+EPx

MGW U5.0

MGW U5.0+EPx

M14.6

M15.0

M15.1

M16.0

Multicontroller

RNC (mcRNC)

BCN Platform mcRNC2.0 Flexi NS-SGSN DX SG7.0 CD5








CDx

Base

Transceiver

Station (BTS)

Flexi WN7.0 1.0

WN7.0 2.0

RN6.0 1.x

RN6.0 2.0

mcRNC2.0

RL20

RL30

Flexi Direct RU30

FIU 19E 3.2

Flexi Packet rel 1.2

compatible with WN7.0 2.0

compatible with WN7.0 1.0 and

WN7.0 2.0

Zero Footprint Solution with

Transport card FTFB, FTIB,

FTLB, Synchronous Ethernet

interoperability


Flexbus Interface with Transport

card FTFB (IP, Dual, ATM Iub),

FTFA (ATM Iub only)


Issue: 06B DN70140703 31


32/46


Networkelement

HW release

SW release

Supports

Note

Flexi Packet Radio 1.2, 1.3, 1.3

EP1

Flexi Packet Multiradio 2.0


2.1


FH 6.07 (FlexiHopper)

FHP 2.7 (FlexiHopper Plus)

FlexiHybrid 2.1

FlexiHybrid 3.1 SU1

Flexi Metro SVR 4.10 SU2


SRAL XD SVR 3.10

SRAL XD SVR 3.10 SU2


FPH1200 R4.5, R5.0

FPH2200 R4.5, R5.0




FTFA (ATM Iub only)

Base

Transceiver

Station (BTS)

Flexi WN7.0 1.0

WN7.0 2.0




1.0

FlexiPacket Firstmile 1.0


EP1


Release 2.0


Release 2.5


Release 2.0

Tellabs 8660 FP2.9

Tellabs 8630 FP2.9

Tellabs 8660 FP2.11A


Tellabs FP3.1

used as ATM PWE Gateway


used as CESoPSN Gateway



OSS5.4 CD Set 1 and OSS5.4

CD Set 2 are compatible with

WN7.0 1.x and WN7.0 2.0.

OSS5.4 CD Set 2 enhances thesupport with updated parameter


It isstrongly recommended to take

the latest NetAct CD set available

at the time of deployment.



32 DN70140703 Issue: 06B


33/46


Networkelement

HW release

SW release

Supports

Note

OSS5.3 MP1+PCDs/OSS5.3

MP2

OSS5.4 CD Set 1

OSS5.4 CD Set 2

Ex3.1

Ex4.1

LN3.0

LN3.1

Operations

Support (OS)

- OSS5.3

MP1/MP2

OSS5.4 CD Set

1 /OSS5.4 CD

Set 2

RN5.0

RN6.0 1.x

RN6.0 2.0

RNC OMS 1.0 1.x

RL20

RL30

S14

S15

I-HSPA Rel3

Flexi Direct RU30

FIU 19E 3.2

FH 6.7

FXC RRI sw ITN C3

AXC C6.0

Flexi WN6.0

Flexi WN7.0 1.0

compatible with OSS5.3 MP1 +

PCDs and OSS5.3 MP2

Compatible with OSS5.4 CD Set

1 and OSS5.4 CD Set 2. OSS5.4

CD Set 2 enhances the support

with updated parameter





deployment.

compatible with OSS5.3MP1/MP2

compatible with OSS5.3 MP1

(PCD required for full support)

compatible with OSS5.4 CD Set 1

compatible with OSS5.3 MP1 +

PCDs and OSS5.3 MP2

Operations

Support (OS)

- OSS5.4 CD Set

1 /OSS5.4 CD

Set 2

Flexi WN7.0 2.0

Ultra WN6.0

MGW U4.0

MGW U4.1

MGW U4.2

MGW U4.2+EPx

MGW U5.0

MGW U5.0+EPx

M14.6

Compatible with OSS5.4 CD Set

1 and OSS5.4 CD Set 2. OSS5.4

CD Set 2 enhances the support

with updated parameter





deployment.


Issue: 06B DN70140703 33


34/46


Networkelement

HW release

SW release

Supports

Note








Ex3.1

RNC Operation

and

Maintenance

Server (RNC

OMS)

MCP18 B RNO 1.0 1.x RN6.0 1.x

RN6.0 2.0

OSS5.3 MP1/MP2

OSS5.4 CD Set 2

compatible with RNO 1.0 1.x

compatible with RNO 1.0 2.0


compatible with RNO 1.0 1.x and

RNO 1.0 2.0

HP Proliant -

DL 360 G6

5540

RNO 1.0 1.x RN6.0 1.x

RN6.0 2.0

mcRNC2.0

OSS5.3 MP1/MP2

OSS5.4 CD Set 2


compatible with RNO 1.0 2.0



compatible with RNO 1.0 1.x and

RNO 1.0 2.0

Table 2 RU30 compatibility with core networks and other systems

Network element

HW item

SW release

Note

MultimediaGateway (MGW) IPA 2800 U4.0U4.1

U4.2

U4.2+EPx

U5.0

U5.0+EPx

3G MSC not supportedCM support from U4.0 onwards

3G MSC not supported

SAU4.1 PCD6.1 installation recommended


Backwards compatible


Mobile Switching

Center (MSC)

DX200 M14.x

M15.x

X represents all the sub-releases of M14.



34 DN70140703 Issue: 06B


35/46

Table 2 RU30 compatibility with core networks and other systems (Cont.)

Network element

HW item

SW release

Note

M16.0 Backwards compatible

Serving GPRS

Support Node

(SGSN)

IP3400/IPSO SG7.0 CD2

SG7.0 CD4

SG7.0 CD5

SG7.0 CD6

SG7.0 CD7

SG7.0 CD8

SG8.0

SG8.0 CDx

SG8.0 ATCA

SG8.0 ATCA CDx

DX200

3.2 Flexi Direct RU30 compatibility

Table 3 Compatibility of network elements that belong to Flexi Direct RU30

Network

element

HW

release

SW release

Supports

Note

Combi SGSN - Flexi NS-SGSN DX SG7.0 CD5







Flexi NS-SGSN ATCA SG8.0 CDx

3GPP Rel. 7

3GPP Rel.8

NetAct - OSS5.4 CD Set 1 - -

MSC Server - M14.6

M15

M15.1

M16 (ATCA-based)

M16.1 (ATCA&DX-based)

- -


Issue: 06B DN70140703 35


36/46

Table 3 Compatibility of network elements that belong to Flexi Direct RU30 (Cont.)

Networkelement

HWrelease

SW release

Supports

Note

OMS HP Proliant

DL360

G5&G6

I-OMS4.0 ADA4.0 -

Flexi Network

Gateway

- NG10 CD4

NG10 CD8

NG20

- -

BTS Flexi BTS Flexi WN7.0 1.0

WN7.0 2.0

- Possible

with FlexiRel2 HW

when

FTLB

used.

Flexi Direct

RNC

FTLB ADA4.0 - -

IPA-RNC IPA 2800

A12

RN6.0 1.x - -

mcRNC BCN

Platform

mcRNC2.0 - -

Flexi ISN - FI50, FI50CD2 - -

MGW - U4.2

U4.2+EPx

U5.0

U5.0+EPx

- -

LTE - FDD LBTS 2.0 - -

Table 4 Compatibility of network elements that do not belong to Flexi Direct RU30

Network

element

HW release

SW release

Supports

Note

IPA-RNC IPA 2800 A11 RN5.0 - -

Flexi ISN - FI40 CD4 - -

BSC - S14, S15 - -


36 DN70140703 Issue: 06B


37/46

Table 4 Compatibility of network elements that do not belong to Flexi Direct RU30(Cont.)

Network

element

HW release

SW release

Supports

Note

Flexi Direct

RNC

FTLB ADA3.0 - -

3.3 RU40 compatibility

Table 5 RU40 system product

Network

element

HW release

SW release

Supports

Note

IPA-RNC

(Radio Network

Controller)

IPA 2800

A14

RN7.0 RN6.0

mcRNC3.0

mcRNC2.0

RNC OMS 2.0

Flexi Direct RNC ADA5.0


RL40

RL30

S16.1

S16

S15

AXC C6.0

Flexi WN8.0

Flexi WN7.0 2.0

Flexi WN7.0 1.0

FM200i

Ultra WN6.0


S1.1)


R2.8)

Cisco 7600 (IOS 12.2(33) SRD)

Cisco 7600 (IOS 15.0(1)S)

Cisco 7600 (IOS 15.1(2)S1)

compatible with RN6.0 1.x and

RN6.0 2.0


Issue: 06B DN70140703 37


38/46


Networkelement

HW release

SW release

Supports

Note


2.1





1.0


EP1

FlexiPacket Firstmile 200Release

2.0

IPA-RNC

(Radio Network

Controller)

IPA 2800

A12

RN7.0 FlexiPacket Firstmile 200

Release 2.5


Release 2.0

Flexi ISN FI50+CDx

Flexi NG (GGSN) NG10 CDx



Tellabs 8600 series

OSS5.4 CD set 3

MGW U6.0

MGW U5.0+EPx

MGW U4.2+EPx

MGW U4.2

MGW U4.1

MGW U4.0

Open MGW U5i+Epx

M16.1 (ATCA-based)

M16+EPx (ATCA-based)

M16.1

M16+EPx

M15.x

M14.x

ATCA-based

Open MSS ATCA-based

Open MSS


38 DN70140703 Issue: 06B


39/46


Networkelement

HW release

SW release

Supports

Note


CDx


Multicontroller

RNC (mcRNC)

BCN Platform mcRNC3.0 RN7.0

RN6.0

mcRNC2.0

RNC OMS 2.0



RL40

RL30

S16.1

S16

S15

Flexi WN8.0

Flexi WN7.0 2.0

Flexi WN7.0 1.0

FM200i

EUBB WCDMA BTS WN6.0


S1.1)


R2.8)

Cisco 7600 (IOS 12.2(33) SRD)

Cisco 7600 (IOS 15.0(1)S)

Cisco 7600 (IOS 15.1(2)S1)


2.1





1.0


EP1


Issue: 06B DN70140703 39


40/46


Networkelement

HW release

SW release

Supports

Note

FlexiPacket Firstmile 200Release

2.0

Multicontroller

RNC (mcRNC)

BCN Platform mcRNC3.0 FlexiPacket Firstmile 200

Release 2.5


Release 2.0

Flexi ISN FI50+CDx

Flexi NG (GGSN) NG10 CDxFlexi NG (GGSN) NG2.1


Tellabs 8600 series

OSS5.4 CD set 3

MGW U5.0+EPx

MGW U4.2+EPx

MGW U4.2

MGW U4.1

MGW U4.0

Open MGW U5i+Epx

M16.1 (ATCA-based)

M16+EPx (ATCA-based)

M16.1

M16+EPx

M15.x

M14.x



CDx

ATCA-based

Open MSS ATCA-based

Open MSS

Base

Transceiver

Station (BTS)

Flexi WN8.0 RN7.0

mcRNC3.0

RL50

RL40

RL30

Flexi Direct RU40

FIU 19E 3.2


Transport card FTFB, FTIB,

FTLB, Synchronous Ethernet

interoperability




FTFA (ATM Iub only)


40 DN70140703 Issue: 06B


41/46


Networkelement

HW release

SW release

Supports

Note

Flexi Packet rel 1.2

Flexi Packet Radio 1.2, 1.3, 1.3

EP1

Flexi Packet Multiradio 2.0


2.1


FH 6.07 (FlexiHopper)

FHP 2.7 (FlexiHopper Plus)

FlexiHybrid 2.1

FlexiHybrid 3.1 SU1



SRAL XD SVR 3.10



FPH1200 R4.5, R5.0

FPH2200 R4.5, R5.0



card FTFB(IP, Dual, ATM Iub),

FTFA (ATM Iub only)

Base

Transceiver

Station (BTS)

Flexi WN8.0 FlexiPacket Hub 800 Release 2.0



1.0

FlexiPacket Firstmile 1.0


EP1


Release 2.0


Release 2.5

FlexiPacket FirstMile 200i

Release 2.0


Release 2.0

Tellabs 8660 FP2.9

Tellabs 8630 FP2.9







Issue: 06B DN70140703 41


42/46


Networkelement

HW release

SW release

Supports

Note


Tellabs FP3.1

OSS5.4 CD set 3

Ex5.1

Ex5.0

Ex4.2

Ex4.1

LN5.0

LN3.2

LN3.1

GF1.0

Operations

Support (OS)

- OSS5.4 CD set

3

RN7.0

RN6.0 2.0

RN6.0 1.0

RN6.0

RL25TD

RNC OMS 2.0

RNC OMS 1.0

RL40

RL30

S15 EP2.1

S15 EP1.1

S16

S15.2

S15

Flexi Direct RU40

Flexi Direct RU30

FIU 19E 3.2

FH 6.7

FXC RRI sw ITN C3

AXC C6.0

Flexi WN8.0

Flexi WN7.0 2.0


42 DN70140703 Issue: 06B


43/46


Networkelement

HW release

SW release

Supports

Note

Flexi WN7.0 1.0

FM200i

Ultra WN6.0

MGW U5.0

MGW U5.0 EP2

MGW U5.0 EP1

M16.0

M15.1

M15.0

M14.6

Ma16.1

Md16.1

Md16.1 EP1

Flexi NSSGSN SG8.0

Flexi NS-SGSN SG8.0 ATCA

CD3

Flexi NS-SGSN SG8.0 ATCA

CD2

EX5

EX4.2

EX4.1

EX4

OMS (RNC

OMS)

HP ProLiant

DL360 G6 HP

ProLiant

DL360p G8 HPProLiant

BL460c G8

RNC OMS 2.0

RNC OMS 2.0

RNC OMS 2.0

Table 6 RU40 compatibility with core networks and other systems

Network element

HW item

SW release

Note

Multimedia

Gateway (MGW)

IPA 2800 U4.0

U4.1


CM support from U4.0 onwards


Issue: 06B DN70140703 43


44/46

Table 6 RU40 compatibility with core networks and other systems (Cont.)

Network element

HW item

SW release

Note

U4.2

U4.2+EPx

U5.0

U5.0+EPx

U5i(Atca),

U5i(Atca)+EPx


SAU4.1 PCD6.1 installation recommended




Mobile Switching

Center (MSC)

DX200 M14.x

M15.x

M16+EPx M16.1

M16+EPx (Atca-

based) M16.1

(Atca-based)

X represents all the sub-releases of M14.



Serving GPRS

Support Node

(SGSN)

IP3400/IPSO SG7+CDx

SG8.0

SG8.0 CDx

SG8.0 ATCA

SG8.0 ATCA CDx

DX200

3.4 Flexi Direct RU40 compatibility

Table 7 Compatibility of network elements that belong to Flexi Direct RU40

Network

element

HW

release

SW release

Supports

Note

Combi SGSN - Flexi NS-SGSN ATCA SG8.0 CDx


- -

NetAct - OSS 5.4 CD set 3 - -

MSC Server - M16+Epx (ATCA-based)

M16.1 (ATCA-based)

M16.1

M16+EPx

M15.x

M14.x

Open MSS

ATCA-based

Open MSS

-


44 DN70140703 Issue: 06B


45/46

Table 7 Compatibility of network elements that belong to Flexi Direct RU40 (Cont.)

Networkelement

HWrelease

SW release

Supports

Note

OMS HP Proliant

DL360 G6

HP

ProLiant

DL360p G8

I-OMS5.0 I-OMS5.0 - -

Flexi Network

Gateway

- Flexi NG (GGSN) NG10 CDx



- -

BTS Flexi - WN8.0 - Possiblew

ith

FlexiRel2

HWwhen

FTLB

used.

Flexi Direct

RNC

FTLB ADA5.0 - -

IPA-RNC IPA 2800

A13

RN7.0 - -

mcRNC BCN mcRNC3.0 - -

Flexi ISN - Flexi ISN FI50+CDx - -

MGW - Open MGW U5i+Epx MGW

U5.0+Epx

MGW U4.2+EPx

MGW U4.2

- -

LTE - FDD LBTS 4.0

FDD LBTS 3.0

- -

Table 8 Compatibility of network elements that do not belong to Flexi Direct RU40

Network

element

HW release

SW release

Supports

Note

IPA-RNC IPA 2800 A12 RN6.0 - -

mcRNC - mcRNC2.0


Issue: 06B DN70140703 45


46/46

Table 8 Compatibility of network elements that do not belong to Flexi Direct RU40(Cont.)

Network

element

HW release

SW release

Supports

Note

Flexi ISN - FI40 CD4 - -

BSC - S16.1, S16,

S15

- -

BTS Flexi - WN7.0 2.x

WN7.0 1.x

- -

Flexi Direct

RNC

FTLB ADA4.0 - -


46 DN70140703 Issue: 06B

compa_wcdma_ihspa-0900d80580a21658

Documents

Transcript of compa_wcdma_ihspa-0900d80580a21658