GE Commercial Laundry
TECHNICAL SERVICE GUIDE
MODEL SERIES
ELECTRIC AND GAS DRYERS
DCCD330ED/DCCD330GD (Countdown)DCCB330ED/DCCB330GD
Pub 31-15557 06/03
Commerical Commerical
DryerDryer
PERMAMENT PRESS
PERMAMENT PRESS
HIGH HEAHIGH HEA
HIGH HEAT
COOL DOWN CYCLE
COOL DOWN CYCLE
LOW HEALOW HEAT
RESUME HEARESUME HEARESUME HEATRESUME HEAT
1.1.2.2.
Add coins for extra dry time.
Add coins for extra dry time.
If dryer door is opened during
If dryer door is opened during
cycle, push PRESS TO ST
cycle, push PRESS TO STARTART
button again to resume cycle.
button again to resume cycle.SYNTHETIC
KNITSSYNTHETIC KNITS
PRESS TO STPRESS TO STARTART
OPERAOPERATINGTING
PRESS TO STARTPRESS TO START
SYNTHETIC KNITSSYNTHETIC KNITS
PERMAMENT PRESS
PERMAMENT PRESS
COTTONSCOTTONS
COOL DOWN CYCLE
COOL DOWN CYCLE
LOW HEATLOW HEAT
button again to resume cycle.
button again to resume cycle.
cycle, push PRESS TO START
cycle, push PRESS TO START
If dryer door is opened during
If dryer door is opened during
Add coins for extra dry time.
Add coins for extra dry time.
TINGTING
HIGH HEAT WITH
GE Commercial 7.0 Cubic Foot DryersExtra Large Capacity Dryers Gas/Electric
!IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use byindividuals possessing adequate backgrounds of electrical,electronic, and mechanical experience. Any attempt to repair amajor appliance may result in personal injury and propertydamage. The manufacturer or seller cannot be responsible for theinterpretation of this information, nor can it assume any liability inconnection with its use.
WARNINGIf the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury ordeath. If you smell gas:
- Do not try to light any appliance.- Do not touch any electrical switch; do not use any phone in
the building.- Immediately call the gas supplier from a neighbors phone.
Follow the gas suppliers instructions.- If you cannot reach the gas supplier, call the fire department.
WARNINGTo avoid personal injury, disconnect power before servicing this
product. If electrical power is required for diagnosis or testpurposes, disconnect the power immediately after performing thenecessary checks.
RECONNECT ALL GROUNDING DEVICESIf grounding wires, screws, straps, clips, nuts, or washers used
to complete a path to ground are removed for service, they mustbe returned to their original position and properly fastened.
GE Commercial Laundry ServiceTechnical Service Guide
Copyright 2003
All rights reserved. This service guide may not be reproduced in whole or in partin any form without written permission from the General Electric Company.
1
Countdown Display Models
Countdown Display Diagnostics
Rating Plate and Service Information
2
3
4
5
6
7-12
Table of Contents
13
14-15
16-17
18
Model Series Features
Dryer Operation
Installation Highlights
Temperature Switch and Controls
Dimensions and Specifications
rvice Info.
Warranty
Gas Schematics
Mechanical Disassembly
Electric Schematics
Troubleshooting Charts
Exploded Views Parts Pages
19
20-22
23-34
35
2
Model Features
Features and Benefits 7.0 cu. ft. super capacity Electronic cycle countback 3 cycles 3 heat selections5-Year parts warranty dryer drum and cabinet rust-throughPARTS ONLY WARRANTY, NO LABOR WARRANTYSee written warranty for details.
DCCB330ED Electric Dryer(not shown)
DCCB330GD Gas Dryer(not shown) 7.0 cu. ft. super capacity 3 cycles 3 heat selectionsPlus:3-Year parts warranty5-Year parts warranty dryer drum and cabinet rust-throughPARTS ONLY WARRANTY, NO LABOR WARRANTYSee written warranty for details.
New!Dryer ON light indicates thatdryer is operating.
DCCD330ED - GE 7.0 Cu. Ft. Extra Large
DCCD330GD - GE 7.0 Cu. Ft. Extra Large
Features and Benefits 7.0 cu. ft. super capacity Electronic cycle countback 3 cycles 3 heat selections5-Year parts warranty dryer drum and cabinet rust-throughPARTS ONLY WARRANTY, NO LABOR WARRANTYSee written warranty for details.
Exhaust Options:Electric: 4-way venting: left, right, bottom and
rear.Maximum recommended exhaust duct length is45 feet of rigid ducting with two 900
elbows and 4 dampered wall cap.Gas: 3-way venting: left, bottom and rear.Maximum recommended exhaust duct length is15 feet of 4: rigid ducting with two 900 elbowsand a dampered wall cap.Dryer is shipped with exhaust in the rear.(See installation instuctions)
3
Countdown display (DCCDThe countdown display shows the remainingoperating time as well as the current drying cycle.The display board is configured for a 45-minutedry time at the factory to correspond with the 45-
4
To verify correct operation of Countdown DisplayBoard.
1. Make sure power is ON to dryer.2. Advance coin box timer one cycle.3. The display should read 88 for twoto three seconds, then default to the dipdip switch settings. (Factory setting is 454. At the same time the 88 display isshown the four indicator LEDs shouldlight for 2-3 seconds. Next the PRESSSTART LED will blink and other indicatorlights will go off. (If dryer door is NOTopen.)5. Replace the board if LEDs and Displaydo not function as described in #3 and#4 above.
NOTE: The board does not control any cycle timeduration of the dryer. The dryer will function nor-mally if there is a complete failure of the board.It is the owners discretion whether or not theboard should be replaced.
To replace Countdown Display PC Board:WARNING! THE STEP DOWN CAPACITORON PC BOARD IS 120 VOLTS, ANDPOWER MUST BE REMOVED PRIOR TOSERVICING. THE TRACES ON THEBOARD RUNNING TO THE CAPACITORARE HOT.
1. Remove the four screws in the top of thecontrol panel.2. Disconnect harness connector to PC board.3. Remove two screws mounting PC Board oneach end.4. Depress the four tabs shown in illustration andlift PC board out of control assembly.5. Align countdown display on control panel andinstall two mounting screws.
88
!
COUNTDOWN DISPLAY AND DIAGNOSTICS
5
Circuit Requirements: Electric-An individual branchcircuit fused for 30-amps is required for each dryer.Electric Dryer Rating: 240V, 60Hz, 5600W, 24A or208V/60Hz, 440W, 22A.
Gas Dryer Rating: 115V, 60Hz. Factory equippedfor natural gas. Tested for LP gas. A conversion kit isrequired for LP Gas. Check installation instructionsfor correct kit number. Have a qualified technicianinstall the conversion kit. Equipped with with energysaving Glo-Bar ignition. Gas: An individual branchcircuit is fused for 15- or 20 amp is required for eachdryer.
Dryer Note: Dryer wall outlet must be located within36 of service cord entry and accessible when dryeris mounted in position.
NOTE: Dimensions and specifications shown hereare correct at the time this book was printed. Beforeproceeding with construction or rough-in, checkinstallation instructions that came with your unit.Specifications, dimensions and design are subjectto change without notice
DIMENSIONS AND SPECIFICATIONS
NOTE: Dimensions and specifications shownhere are correct at the time this manual wasprinted. Before proceeding with constructionor rough-in, check installation instructions thatcame with your unit. Specifications, dimen-sions and design are subject to change with-out notice.
6
RATING PLATE AND SERVICE INFORMATION LOCATION
GE Commercial Dryers have a rating plate con-taining model, serial number and UL listing. It islocated on the inside of door opening at the top-right. You can see the rating plate by simplyopening the dryer door.
CAUTION!: Always disconnect appliance frompower prior to servcing to avoid shock.
A mini-manual is provided inside the control paneland has basic service information. On the backside of the mini-manual is the product schematic,which is valuable in troubleshooting problems.Resistances, voltages, and wiring colors areshown and can be used with a volt-ohm meter tocheck circuitry and components for resistance andcontinuity. (POWER SHOULD BE DISCON-NECTED!)
The illustration on the right shows graphic infor-mation on how to access the mini-manual byremoving the 4 T20H Torx screws and the mini-manual is located in the control panel housing.
REMOVE 4 T20H TORX SCREWS RE
MO
VE
CO
IN
BO
X C
OV
ER
SC
RE
WS
Mini-Manual IS LOCATED INSIDE THECONTROL PANEL.
7
INSTALLATION HIGHLIGHTS
It is IMPORTANT to read and understand thecomplete installation instructions for your GAS orELECTRIC Commercial SmartCard dryers. Theinstallation highlights will cover exhausting tips,gas line installation tips, and electric dryer hookuprequirements. Full comprehensive installationinstructions for your particular model is shippedwith every dryer. FOR QUESTIONS ON INSTAL-LATION, CALL: 1-800-626-2003.
A good installation makes for good performanceand consist of the following steps as outlined inyour installation instruction shipped with theappliance.
STEP 1- Prepare the area and exhaust for instal-lation of new dryer.
STEP 2- Check and make sure the existing exter-nal exhaust is clean and meeted the installationspecifications.
STEP 3- Remove the foam shipping pads.
STEP 4- Move the dryer to the desired location.
STEP 5- Connect powersupply.
STEP 6- Connect the external exhaust.
STEP 7- Level your dryer.
STEP 8- Check the operation of the power supplyand venting.Check the installation instruction forspecial installation for Alcove or Closet, Bathroomor Bedroom, Mobile or Manufactured Home, forside and bottom exhaust. They are completelycovered in the product installation instructions.
FOR YOUR SAFETY:
WARNINGUse only rigid metal or flexible metal 4 diameterductwork for exhausting to the outdoors. Neveruse plastic or other combustible, easy to punctureductwork.
This appliance must be properly grounded andinstalled per the appliance installation instructionsshipped with every appliance.
Do not install or store appliance in an area whereit will be exposed to water and/or weather.
Install the dryer where the temperature is above500 F. for correct operation of dryer controls.
!
EXHAUSTING:
The MOST IMPORTANT element to good perfor-mance is VENTING the dryer. With out sufficientairflow dry times will be longer and linting willdevelop.
If you are installing in an existing wall duct makesure that you make sure the internal duct openingis clear and that the hood damper opens andcloses freely.
Minimum clearance to combustible surfaces andfor air openings are: 0 in. clearance both sides and1 in. rear. Consideration must be given to provideadequate clearance for installation and service.
REMOVE LINT FROM WALL EXHAUST
PREPARING FOR INSTALLATION OF NEWDRYER
8
EXHAUSTING:
NOTE: The correct exhaust installation isYOUR RESPONSIBILITY.Problems due to incorrect installation are NOTcovered in the warranty.
The MAXIMUM ALLOWABLE length of the ex-haust system depends upon the type of duct,number of turns, the type of exhaust hood (wallcap), and all conditions noted below. Both rigidand flexible metal are shown in the chart below.
EXHAUST SYSTEM CHECK LIST
HOOD OR WALL CAP
-Terminate in a manner to prevent back drafts orentry of birds or other wildlife.
-Termination should present minimal resistance tothe exhaust air flow and should require little or nomaintenance to prevent clogging.
-NEVER install a screen in or over the exhaustduct. This could cause lint build up.
-Wall caps must be installed at least 12 in. aboveground level or any other obstructions with theopening pointing down.
-If roof vents or louvered plenums are used, theymust be equivalent to a 4-in. dampened wall capin regard to resistance to air flow, prevention ofback drafts, and maintenance requied to preventclogging.
SEPARATION OF TURNS:
-For best performance, separate all turns with atleast 4 ft. of straight duct., including distancebetween last turn and exhaust hood.
TURNS OTHER THAN 900
-One turn of 450 or less may be ignored
-Two 450 turns should be treated as one 900 turn.
-Each turn over 450 shold be treated as one 900
turn.
SEALING OF JOINTS
-All joints should be tight to avoid leaks. The malelend of each section of duct must point away fromdryer.
-Do not assemble the ductwork with fasternersthat extend into the duct. They will serve to collectlint.
-Duct joints can be made air tight by wrapping theoverlapped joints with duct tape.
-Horizontal runs should slope down toward theoutdoors 1/2 in. per foot.
INSULATION:
Duct work that runs through an unheated area oris near air conditioning, should be insulated toreduce condensation and lint build-up.
WARNING! - TO REDUCE THE RISKOF FIRE OR PERSONAL INJURY:
-Exhausting the dryer to the outdoors is stronglyrecommended to prevent large amounts of moisturefrom being blown into the room.
-Use only metal duct.-Do not terminate exhaust in a chimney, any gas vent,
under an enclosed door (crawl space), or into anattic. The accumulated lint could create a firehazard.
-Provide an access for inspection and cleaning of theexhaust system, especially at turns. Inspect andclean at least once a year.
-Never terminate the exhaust into a common duct withkitchen exhaust. A combination of lint and greasecould create a fire hazard.
-Do not obstruct incoming or exhausted air.
!
9
INSTALLATION HIGHLIGHTS/VENTING
10
INSTALLATION HIGHLIGHTS/LEVELING
It is also important that you take the time to levelthe dryer. It helps to remove vibration, walking,and improves clothing turn over rate for improveddrying. Illustration below show the correct methodto level the dryer.
INSTALLATION HIGHLIGHTS/ELECTRIC 4WIRE HOOK UP:
WARNING- TO REDUCE THE RISK OF FIRE,ELECTRICAL SHOCK AND PERSONAL INJURY:-DO NOT USE AN EXTENSION CORD OR ANADAPTER PLUG WITH THIS APPLIANCE.
Dryer must be electrically grounded in accordancewith local codes and ordinances, or in absence oflocal code, in accordance with NATIONAL ELEC-TRICAL CODE. ANSI/NFPA NO. 70.
!
INSTALLATION HIGHLIGHTS/ELECTRICAL REQUIREMENTS(ELECTRIC DRYER)This dryer must be connected to an individualbranch circuit, protected by the required time-delay fuses or circuit breakers. A four or threewire, single phase, 120/240V or 120/208V, 60Hz, 30 amp circuit is required.
If the electric supply doesnt meet the abovespecifications, then call a licensed electrician.
GROUNDING INSTRUCTIONS
This dryer must be connected to a groundedmetal, permanent wiring system, or an equip-ment-grounding conductor must be run with thecircuit conductor and connected to the equip-ment grounding terminal on the appliance.
ELECTRIC 4-WIRE HOOK UP:
1. Turn off the circuit breaker (s) (30 amp) orremove the dryers circuit fuse at the electricalbox.
2. Be sure the dryer cord is unplugged from thewall receptacle.
3. Remove the power cord cover located at theback.
11
INSTALLATION HIGHLIGHTS/ELECTRIC(CONT)
4. Remove and discard ground strap. Keep thegreen ground screw for step 7.
5. Install 3/4 UL recognized strain relief to powercord entry hole. Bring power cord through strainrelief.
6. Connect power cord as follows:
A. Connect the 2 hot lines to the outerscrews of the terminal block (marked L1and L2).
B. Connect the neutral (white) line to thecenter of the terminal (marked N).
7. Attach ground wire of power cord with the greenground screw (hole above strain relief bracket).tighten all terminal block screws (3) completely.
8. Properly secure power cord to strain relief.
9 Reinstall cover.
WARNING: NEVER LEAVE THECOVER OFF THE TERMINAL BLOCK.!
7. Properly secure power cord to strain relief.
8. Reinstall the cover.
WARNING: NEVER LEAVE THECOVER OFF THE TERMINAL BLOCK.!
ELECTRIC 3 WIRE HOOKUP
ELECTRIC 3 WIRE HOOK UP:
1. Turn off the circuit breaker (s) (30 amp) orremove the dryers circuit fuse at the electricalbox.
2. Be sure the dryer cord is unplugged from thewall receptacle.
3. Remove the power cord cover located at theback.
4. Install 3/4 UL recognized strain relief to powercord entry hole. Bring power cord through strainrelief.
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outerscrews of the terminal block (marked L1and L2).
B. Connect the neutral (white) line to thecenter of the terminal (marked N).
6. Be sure ground strap is connected to neutral(center) terminal of block and to green groundscrew on cabinet rear. Tighten all terminal blockscrews (3) completely.
12
INSTALLATION HIGHLIGHTS/GAS
TIGHTEN ALL CONNECTIONS USING TWOADJUSTABLE WRENCHES
GAS SUPPLY
A 1/8-in. National Pipe Taper thread pluggedtapping, accessible for test gauge connection,must be installed immediately upstream for thegas supply connection to the dryer. Contact yourlocal gas utility should lyou have questions on theinstallation of the plugged tapping.Supply line is to be 1/2-in. rigid pipe and equippedwith an accessible shut-off within 6 ft. of, and inthe same room with, the dryer.Use pipe thread sealer compound appropriate fornatural or LP gas or use Teflon Tape.Connect flexible metal connector to dryer and gassupply.Open shut-off valve, use commercial leak detectorfluid and check for leaks. Reinstall if leaks aredetected.
USE COMMERCIALLEAK TEST FLUIDTO CHECK FOR
LEAKS
13
DRYER CONTROLS
To access the dryer controls, disconnect powerand remove the four T20H Torx screws at the topof the switch trim, remove the screws and theswitch trim coinbox cover(shown in illustrationbelow). Remove the coin box and gently pull theswitch trim from the top, it is supported on threetabs from the top panel to switch trim.
TIMER
The timer is an electromechanical control with a115v drive motor. On a timed cycle, the timermotor receives 115 volts continuously for thenumber of minutes selected for the cycle. Thetimer/accumulator assembly consist of a mountingbracket, timing motor, snap switch, timing cam,drive (timing cams) coil spring(pawl), torsionspring (rachet asm),amd coil spring (index lever). The timing motor is115V-60HZ, and runs at 1/180 R.P.M. It isshipped from the factory with a 45 minute cycletime. This can be changed by ordering a differentmotor. (specify voltage, frequency, and speed.)from Greenwald Industries. See sample partscatalog pages for timer section for full address.
MountingBracket
Timing Motor
Enclosed SnapSwitch
Coil Spring(pawl)
Torsion Spring(Ratchet Asm)
Drive(Timing Cams)
Timing Cam
Coil Spring(Index-Lever)
Greenwald Industries, Inc.1340 Metropolitan AVe.,Brooklyn, N.Y 11237Phone 1-800-221-0982
TIMER/ACCUMULATORREMOVE 4 T20H TORX SCREWS RE
MO
VE
CO
IN
BO
X C
OV
ER
SC
RE
WS
TEMPERATURE SELECTOR SWITCHThe temperature selector switch allows the cus-tomer to select temperature settings for drying. Theswitch contains a 3.5k ohm resistor on the electricmodel and a 1.7k ohm resistor on the gas model.On the LOW HEAT setting, the selector switchactivates a control thermostat bias heater, which isin series with the resistor on the switch. To checkthe switch, disconnect power, remove the wiresfrom the switch and check for continuity. With theswitch set on REGULAR setting, there should becontinuity only between terminals 1 and 4. On theMEDIUM setting, there should continuity onlybetween terminals 4 and 5. On the LOW HEATsetting there is continuity between all sets of termi-nals (1-4, 2-5). TIMER SELECTOR SWITCH
14
DRYER OPERATION
ACCESSING THE DRYER COMP0NENTS
Top Panel Removal
The top panel is mounted to the dryer front by fourscrews. The four T20H Torx screws should beremoved from the top of the control panel. Removethe coinbox to backsplash trim, lay the coin boxaside, and carefully lift the top panel. There are tabsprotruding from the cabinet base to the top andcare must be taken to reinsert them when replacingthe top.
Front Panel RemovalTo remove the front panel, disconnect power andremove top panel as discribed in previous para-graph. Remove two screws on either side mountingfront to cabinet base. Tilt out the top of the front andlift it off base. Disconnect door switch and carefullysit the front aside.
REMOVE TWO SCREWSTHAT ATTACH FRONT TO
CABINET FROM TOP
REMOVE FOUR SCREWSTO REMOVE TOP
The drumis driven by a rubber belt from a shaft offthe rear of the motor and is tensioned by a springloaded idler pulley. Drum rotates counterclockwiseat 47-51 RPM.
TILT FRONT
15
DRYER OPERATION
AIRFLOW AND SEALS(Electric Dryer)Proper air flow through the dryer is essentialfor normal operation of the temperaturecontrol and safety systems. Air is PULLEDinto the cabinet from rear, and drawn upacross the heaters located behind the drum.This hot air is PULLED through the drumrear across the clothes load, through the linttrap and down the trap duct into the blower.From the blower the air is PUSHED out ofthe exhaust system.
(GAS and ELECTRIC)Any air leaks between the air inlet and the blowersuch as lower drum front felt or trap duct to cabi-net front sealing will result in improper tempera-tures. The air being pulled down the trap duct tothe drum outlet thermostat will be cooler thannormal, giving the thermostat a false indication(delayed or no-trip). Leaks ahead of the blower willalso reduce the volume of air across the heatercausing hot spots and possible premature failures.
TRAP DUCT SEALINGTo inspect the trap duct for proper sealing, removethe lint filter and look down into the duct. With alight examine the trap duct on all sides where itmeets the dryer front for voids in sealing. Leaksmay be sealed with permagum.
AIRFLOW AND SEALS
As with the electric the gas dryer must haveproper air flow through the dryer and is essentialfor normal operation of the temperature controland safety systems. Air is PULLED into the cabi-net. A portion of this air is heated by the gasburner in the conbustion chamber and ispulled upthe rear duct into the diffuser. The remainder ofthis air enters the diffuser directly through ventsand is mixed with heated air. This hot air isPULLED through the drum rear, across theclothes load, through the lint trap and down thetrap duct into the blower. From the blower air isPUSHED out the exhaust system.
-WHEN FLEXIBLE DUCT IS USED WESTRONGLY RECOMMEND METALLICFLEXIBLE DUCT.-EXHAUST DUCT MUST BE 100mm (4INCH) DIAMETER.-FOR SPECIFIC EXHAUSTSPECFICATIONS, REFER TO INSTALLA-TION INSTRUCTIONS SUPPLIED WITHYOUR DRYER.
GAS DRYER
ELECTRIC DRYER
16
MECHANICAL DISASSEMBLY
Basic disassembly is very straightforward. Simplehand tools are used with the exception of the (4)T-20H Torx screws from the top of the controlpanel.
Service the control panel:
1. Remove the 4 screws from the top of the controlpanel, and carefully tilt out top releasing from 3tabs.
SERVICE THE COVER:
1. Remove the four screws located in the top leftand right of front dryer opening,
2.Remove the four T-20H Torx screws from thecontrol panel top.
3. Remove screws for control panel bottom, andlift off top.
Service the Cabinet Front:1. Remove screws from right and left corner ofdryer door opening at top.
2. Remove two screws from Front to Cabinetsides.
3. Remove wiring harness connectors at lower leftside of door, tilt front out and lift off base.
SERVICE THE DRUM:
1. Remove the top/front as described previously.
2. Carefully spread sides to accomodate lifting outthe drum.
3. Remove drum belt at bottom front access holeby reaching in and pulling idler arm to release.
REMOVE 4 T20H TORX SCREWS RE
MO
VE
CO
IN
BO
X C
OV
ER
SC
RE
WS
REMOVE FOUR SCREWSTO REMOVE TOP
17
MECHANICAL DISASSEMBLY
4. Lift out drum by lifting up and out to clearcabinet and remove from rear drum bearing.
NOTE: When reassembling make sure belt is onidler correctly, and that drum bearings in the frontof the blower housing is correctly located on thedrum.
SERVICE THE IDLER/MOTOR:
1. Remove Top as described previously.
2. Remove Drum as described preiously.
3. Access to Idler Assembly, and Motor is shown.
SERVICE THE HEAT DEFLECTOR:
1. Remove top as previously described.
2. Remove Front as previously described.
3. Remove Drum as previously described.
4. Access to Heat Deflector is shown.
IDLER
REMOVE 4 SCREWS TO REMOVE
ELECTRIC ILLUSTRATED
SERVICE THE DRUM SHAFT AND BEARINGRETAINER ASSEMBLY:
1. Remove the Top, Drum as described previously.
2. Drum shaft ismounted to heat Deflector, removescrews.
3. Rear of cabinet (view below) shows bearingretainer which can be removed by removing 4screws.
4. Ground strap is visible in illustration, take careto replace it when servicing the bearing retainer.
18
19
20
DRYER WILL NOT RUN
ELECTRIC DRYER
Service Fuse,Breaker, Outlet
problem
Adequate voltageto dryer?
Connections atTerminal Block ok?
Door SwitchContacts Closed?
Idler SpringSwitch Closed?
Check MotorCentrifugal SwitchReading Between
Contacts 4 & 5Or
Use a properlyGrounded Test Cord
Connected toTerminals 4 & 5Does the Motor
Run?
Y
Y
Repair TerminalBlock Connection
Replace DoorSwitch
Contacts ClosedOn Hi Limit Switch?
Start Switch Contacts3 & 6 Closed?
Replace StartSwitch
Replace HiLimit Switch
Replace IdlerSwitch
Replace Motor
Open WiringBetween
Components.Locate and
Repair
Y
N
Y
N
N
Y
Y
N
N
Y
N
N
GAS DRYER
Service Fuse,Breaker, Outlet
problem
Adequate voltageto dryer?
Door SwitchContacts Closed?
Idler SpringSwitch Closed?
Check MotorCentrifugal SwitchReading Between
Contacts 4 & 5Or
Use a properlyGrounded Test Cord
Connected toTerminals 4 & 5Does the Motor
Run?
Y
Replace DoorSwitch
Start Switch Contacts3 & 6 Closed?
Replace StartSwitch
Replace IdlerSwitch
Replace Motor
Open WiringBetween
Components.Locate and
Repair
Y
N
Y
N
N
Y
Y
N
N
Accumulator ContactsB & C Closed?
Replace TimerIn Coin Box(Greenwald)
N
Y
Accumulator ContactsB & C Closed?
Replace TimerIn Coin Box(Greenwald)
N
Y
21
ELECTRIC DRYER TROUBLE SHOOTING GUIDE(NO HEAT, LONG DRY TIME, CLOTHES WET, WRINKLE, SHRUNK OR DAMAGED)
PROBLEM
NO HEAT LONG DRY TIMECLOTHES WET
Check 240 V.Input To Dryer
Check:Timer Motor andSwitchHeat Select SwitchMotor SwitchTerminals 1 & 2Control Thermostat
NO
Check:Resistance of EachHeater. CheckBetween EachTerminal andCabinet For InfiniteResistance.Heater FailureCould Result FromPoor Air Flow Due toImproper Venting
YES
YES
Check Wiring
Are ClothesStill Damp?
Check:Timer MotorOperation
NO
YES
Check:Exhaust System forRestrictionsThermostat TemperatureTimer OperationWasher Spin Speed andRise TemperatureLoad Size (to large)Ambient TemperatureRoom Size if Ventinginto RoomResistance of Each Heater.Check Between EachTerminal and Cabinet ForInfinite Resistance.Heater Failure Could ResultFrom Poor Air Flow Due toImproper Venting
WRINKLESSHRINKAGE
ANDDAMAGED CLOTHES
ALL fABRICSALL LOADS
Yes
Check:Thermostat TemperaturesDrum Speed (47 - 51 RPM)Washer Spin Speed andRise TemperatureLoad Size (to large)Ambient TemperatureRoom Size if Ventinginto Room
ClothesDamaged
Check:Dryer Drum InteriorSurfacesDrum GapWasher Basket &Actuator
SYNTHETICS
Check:Garment Care Label ForWashing andDrying Instructions
Wrinklesor
Shrinkage
Check:ThermostatTemperaturesClothes ClingTo Drum (NotTumbling) CausedBy Static - CorrectBy Using Two LargeTowels or Fabric Softner
SnagsKnitsOnly
All Hooksand Zippers
Must BeClosed During
Washing & Drying
Snags FrontOnly
Normal Wear
Check 240 V.To Both Heaters
22
GAS DRYER TROUBLE SHOOTING GUIDE(NO HEAT, LONG DRY TIME, CLOTHES WET, WRINKLE, SHRUNK OR DAMAGED)
PROBLEM
NO HEATSHORT BURN CYCLE
LONG DRY TIMECLOTHES WET
Ignitor Operates
Gas Present?
Yes
Check:Gas ValveGas PressureGas Restriction
NO
Check:Flame DetectorTimer MotorHeat Select SwitchMotor SwitchTerminals 1 & 2Control Thermostat
NO
Gas ValveCloses in
Approximately1 - 2 Minutes
YES
YES
Check:Vent System ForRestrictionsSafety Thermostats
Are ClothesStill Damp?
Check:Timer MotorOperation
NO
YES
Check:Exhaust System forRestrictionsThermostat TemperatureTimer OperationWasher Spin Speed andRise TemperatureLoad Size (to large)Ambient TemperatureRoom Size if Ventinginto RoomGas Supply Restrictionsand Pressure
WRINKLESSHRINKAGE
ANDDAMAGED CLOTHES
ALL fABRICSALL LOADS
Yes
Check:Thermostat TemperaturesDrum Speed (47 - 51 RPM)Washer Spin Speed andRise TemperatureLoad Size (to large)Ambient TemperatureRoom Size if Ventinginto RoomGas Supply Restrictionsand Pressure
ClothesDamaged
Check:Dryer Drum InteriorSurfacesDrum GapWasher Basket &Actuator
SYNTHETICS
Check:Garment Care Label ForWashing andDrying Instructions
Wrinklesor
Shrinkage
Check:ThermostatTemperaturesClothes ClingTo Drum (NotTumbling) CausedBy Static - CorrectBy Using Two LargeTowels or Fabric Softner
SnagsKnitsOnly
All Hooksand Zippers
Must BeClosed During
Washing & Drying
Snags FrontOnly
Normal Wear
23
DCCB330GD/DCCD330GD
DCCB330GD GAS NON-COUNTDOWN MODEL
22 155 21 907 35
38213
157
168100
397See Breakdown Page
172
4891483130
396
1
4
727580
7692
875
1553
DCCD330GD GAS COUNTDOWN MODEL
22
382
155 21 907 353
87575
155
10 23
757280120
7692 4
1
396
4891483130
168100
397
172
GAS FRONT PANEL DCCB330GD /DCCD330GD
316 313 1254
312 327
3046
311
325
380
303302 300 14
323
3049
3046
603
307
305
3051
3046610301
24
DCCB330GD/DCCD330GD
204
231
3104
205
3109
203
630
228
3109
230
218
201
202199
502
232
233
239803
216213
215
GAS SUPPLY DCCD330GD /DCCD330GD
730
732 731
729
710
709
712
723
235
721
713
714
717
75
716
BLOWER ASSEMBLY DCCB330GD /DCCD330GD
25
DCCB330GD/DCCD330GD
GAS DRUM ASSEMBLY DCCB330GD /DCCD330GD
3127
508
504
534
509
502
5153102
532
530507
235
405 3106
527
503
526
235 552 3109
GAS CABINET ASSEMBLY DCCB330GD /DCCD330GD
222
421
178241
240
405
456
420
401
403
404
405
408
404
410
236
405
26
1 31-16074 INSTR INSTALL 1
1 31-16087 MINI-MANUAL 1
3 WE19M938 END CAP LH BK 1
4 WE19M939 END CAP RH BK 1
13 WE19M1361 SWITCH TRIM COIN 1
14 WH02X1151 CLIP GROUND 3
30 WE1M533 PLATE SECUR COIN BOX 1
35 WE4M210 P.B. SWITCH 1
72 WE20X811 REAR PANEL 1
75 WE2M173 SCREW 2
80 WE4M308 RESIS (1.7KOHM) GREY 1
100 WH65M185 TIMER & BRACKET ASM 1
112 WR02X10459 PLUG DOOR RVSBL BQ 4
148 WE2M183 BOLT 1/4" 1
155 WH02X1233 SCR 8-18 AB TRT 5/8 S 15
157 WE1X950 LAMP ASM. - AMBER 1
168 WZ02X0468 SCR 10-32 M HS 1/8 S 2
168 WZ2X468D SCR 10-32 M HS 1/8 S 2
172 WH02X0735 SCR 1/4-20 M SH .900 CS 3
173 WE2M182 WASHER LOCK 3
172 WH2X735D SCR 1/4-20 M SH .900 CS 3
178 WE2M175 SCREW # 8 4
199 WE2M98 SCREW 1
201 WE1X306 BLOWER WHEEL 1
203 WE13X0200 STRAP MOTOR 2
204 WE01X0921 STRAP MOTOR 1
205 WE13M36 MOTOR SUPPORT 1
213 WE12M22 BELT DRIVE 1
215 WE3M17 IDLER ARM 1
216 WE12M8 IDLER PULLEY 1
218 WE14M93 BLOWER HOUSING 1
222 WE20M321 BOTTOM COVER COIN 1
228 WE14M90 PIPE EXAUST 1
230 WE4M310 TSTAT OUTLET BIASED 1
231 WE2M187 SCREW 3
232 WE2M156 SCREW 2
233 WE13M35 MOTOR PLATE (E-COAT) 1
234 WE2M96 CAP NUT 1
235 WE1M280 SCREW 16
236 WE1M368 LEVELLING SCREW 4
239 WE2M167 SCREW 2
240 WH01X2266 BUTTON PLUG 1
241 WH01X2268 RETAINER BUTTON 1
300 WE18M21 FILTER FRAME COIN 1
301 WE1M510 DAMPENING PLATE FRT PN 1
301 WE20M323 FRT PN COIN BISQUE 1
302 WE2M189 SCREW 2
303 WE2M181 RUBBER WASHER 2
304 WE2M188 STABILIZING LEG ASM. 2
305 WE10M105 PANEL DOOR INNER CC 1
307 WE10M104 PANEL OUTER CC 1
311 WE14M92 AIR DUCT ASM. 1
312 WE9M15 FELT 1
313 WE3M20 TOP BEARING 1
316 WE1M415 BEARING-SLIDE GREEN 2
316 WE1M504 BEARING-SLIDE WHITE 2
323 WE1M348 PLUG PEEPHOLE GAS 1
325 WE00M169 GASKET (SEAL) 1
326 WE1M473 GASKET SEAL 1
327 WE1M187 LATCH 2
380 WE4M126 DOOR SWITCH 1
382 WH42X10399 DOOR & LATCH ASM 1
396 WE1M534 ADAPT METER CASE 1
397 WE1M535 METER CASE 1
401 WE20M322 COVER COIN BISQUE 1
403 WE02X0405 SCR 8-18 AB OVT 2S 6H 4
404 WE20M310 PANEL SIDE CC 2
405 WE2X263 SCREW 12
408 WE20M320 BASE CABINET COIN 1
410 WE1M467 LEVELLING LEG & BRKT 2
410 WE1M468 LEVELLING LEG & BRKT 2
410 WE1M528 REAR BRKT LEVEL LEG 2
410 WE1M527 FROT BRKT LEVEL LEG 2
420 WE20M300 PANEL REAR 7 CU FT 1
420 WE2M193 PUSH MOUNT CABLE TIE 5
421 WE1M155 CORD CLIP 1
421 WE26M335 CORD SET 120V 1
456 WE01X0617 PIPE CLAMP 1
489 WH01X2572 SLEEVE SPLIT 1
502 WE2M174 SCREW #10 9
503 WE21M13 DRUM ASM 7.0" 1
504 WE14M77 DIFFUSER 1
507 WE4M212 THERMOSTAT 1
508 WE3X39 SHAFT & BRACKET ASSY 1
509 WE14M75 BAFFLE 3
515 WE01X1172 GROUND STRAP ASM 1
526 WE14M70 COMBUSTION CHAMBER 1
527 WE14M88 DUCT TRANSITION 1
530 WE4M80 THERMOSTAT SAFETY 1
532 WE14M83 DIFFUSER GAS ASM. 1
534 WE2M163 SCREW #10 3
543 WE1M462 SLEEVE DRUM 1
552 WE4X448 FLAME DETECTOR 1
603 WE1M482 HANDLE DOOR CC 1
610 WE9M13 GASKET 1
630 WE17M22 MOTOR & PULLEY ASM. 1
VIEW CAT. # DESCRIPTION QTY.
DCCB330GD-NON CNTDWNVIEW CAT. # DESCRIPTION QTY.
DCCB330GD-NON CNTDWN
27
709 WE01X1148 ORIFICE 1
710 WE01X1076 LEAK LIMITER 1
711 1/8-27 NPT PLUG PIPE (NOT STOCK.) 1
712 WE14X0215 GAS VALVE ASM 1
713 WE14X215 VALVE ASM. SHUTOFF 1
714 WE1M512 PIPE & LUG 1
716 WE14X217 BURNER ASM. 1
717 WE04X0739 IGNITER ASM 1
721 WE13X0118 BRACKET SPACER 1
723 WE13X0195 BRACKET GAS VALVE 1
729 WE04X0692 COIL DUAL 1
730 WE02X0333 SCREW (COIL MTG BRKT) 2
731 WE04X0693 COIL MAIN 1
732 WE13X0169 BRKT. COIL 1
803 WD21X0557 SWITCH INTERLOCK 1
875 WD2M101 SCREW 6
DCCB330GD-NON CNTDWN
VIEW CAT. # DESCRIPTION QTY.
907 WD09X0206 PUSHBUTTON 4
1254 WE2M199 PLATE SECUR FRT CAB 1
3046 WE2M170 SCREW #8 10
3049 WE01X1192 STRIKE DOOR 1
907 WD09X0206 PUSHBUTTON 4
3051 WE1M505 HINGE 2
3102 WE1M300 BEARING RETAINER 1
3104 WE2M180 SCREW 1
3109 WE2M154 SCREW 8
3118 WE2M174 SCREW # 10 8
3127 WE1M461 O RING 1
DCCD330GD-COUNTDOWNVIEW CAT. # DESCRIPTION QTY.
1 31-16074 INSTR INSTALL 1
1 31-16092 MINI-MANUAL 1
3 WE19M938 END CAP LH BK 1
4 WE19M939 END CAP RH BK 1
10 WE4M313 CONTROL COIN-OP ASM 1
13 WE19M1372 SWITCH TRIM ASM 1
14 WH02X1151 CLIP GROUND 3
23 WE5M20 HARNESS CNTDN CNTRL 1
30 WE1M533 PLATE SECUR COIN BOX 1
35 WE4M210 P.B. SWITCH 1
72 WE20X811 REAR PANEL 1
75 WE2M173 SCREW 4
80 WE4M308 RESIS (1.7KOHM) GREY 1
100 WH65M185 TIMER & BRACKET ASM 1
112 WR02X10459 PLUG DOOR RVSBL BQ 4
120 WH01X10072 PCB COVER COIN-OP 1
148 WE2M183 BOLT 1/4" 1
155 WH02X1233 SCR 8-18 AB TRT 5/8 S 15
157 WE1X950 LAMP ASM. - AMBER 1
168 WZ02X0468 SCR 10-32 M HS 1/8 S 2
168 WZ2X468D SCR 10-32 M HS 1/8 S 2
172 WH02X0735 SCR 1/4-20 M SH .900 CS 3
173 WE2M182 WASHER LOCK 3
172 WH2X735D SCR 1/4-20 M SH .900 CS 3
178 WE2M175 SCREW # 8 4
199 WE2M98 SCREW 1
201 WE1X306 BLOWER WHEEL 1
203 WE13X0200 STRAP MOTOR 2
204 WE01X0921 STRAP MOTOR 1
205 WE13M36 MOTOR SUPPORT 1
213 WE12M22 BELT DRIVE 1
215 WE3M17 IDLER ARM 1
216 WE12M8 IDLER PULLEY 1
218 WE14M93 BLOWER HOUSING 1
222 WE20M321 BOTTOM COVER COIN 1
228 WE14M90 PIPE EXAUST 1
230 WE4M310 TSTAT OUTLET BIASED 1
231 WE2M187 SCREW 3
232 WE2M156 SCREW 2
233 WE13M35 MTR PLATE (E-COAT) 1
234 WE2M96 CAP NUT 1
235 WE1M280 SCREW 16
236 WE1M368 LEVELLING SCREW 4
239 WE2M167 SCREW 2
240 WH01X2266 BUTTON PLUG 1
241 WH01X2268 RETAINER BUTTON 1
300 WE18M21 FILTER FRAME COIN 1
301 WE1M510 DAMP. PLATE FRT PN 1
301 WE20M323 FRT PN COIN BISQUE 1
302 WE2M189 SCREW 2
303 WE2M181 RUBBER WASHER 2
304 WE2M188 STABILIZING LEG ASM. 2
305 WE10M105 PANEL DR INNER CC 1
307 WE10M104 PANEL OUTER CC 1
311 WE14M92 AIR DUCT ASM. 1
312 WE9M15 FELT 1
313 WE3M20 TOP BEARING 1
DCCD330GD-COUNTDOWN
VIEW CAT. # DESCRIPTION QTY.
316 WE1M415 BEARING-SLIDE GREEN 2
316 WE1M504 BEARING-SLIDE WHITE 2
323 WE1M348 PLUG PEEPHOLE GAS 1
325 WE00M169 GASKET (SEAL) 1
326 WE1M473 GASKET SEAL 1
327 WE1M187 LATCH 2
380 WE4M126 DOOR SWITCH 1
382 WH42X10399 DOOR & LATCH ASM 1
28
DCCD330GD-COUNTDOWN
VIEW CAT. # DESCRIPTION QTY.
396 WE1M534 ADAPT METER CASE 1
397 WE1M535 METER CASE 1
401 WE20M322 COVER COIN BISQUE 1
403 WE02X0405 SCR 8-18 AB OVT 2S 6H 4
404 WE20M310 PANEL SIDE CC 2
405 WE2X263 SCREW 12
408 WE20M320 BASE CABINET COIN 1
410 WE1M467 LEVELLING LEG & BRKT 2
410 WE1M468 LEVELLING LEG & BRKT 2
410 WE1M528 REAR BRKT LEVEL LEG 2
410 WE1M527 FRT BRKT LEVEL LEG 2
420 WE20M300 PANEL REAR 7 CU FT 1
420 WE2M193 PUSH MOUNT CABLE TIE 5
421 WE1M155 CORD CLIP 1
421 WE26M335 CORD SET 120V 1
456 WE01X0617 PIPE CLAMP 1
489 WH01X2572 SLEEVE SPLIT 1
502 WE2M174 SCREW #10 9
503 WE21M13 DRUM ASM 7.0" 1
504 WE14M77 DIFFUSER 1
507 WE4M212 THERMOSTAT 1
508 WE3X39 SHAFT & BRKT ASSY 1
509 WE14M75 BAFFLE 3
515 WE01X1172 GROUND STRAP ASM 1
526 WE14M70 COMBUSTION CHAMBER 1
527 WE14M88 DUCT TRANSITION 1
530 WE4M80 THERMOSTAT SAFETY 1
532 WE14M83 DIFFUSER GAS ASM. 1
534 WE2M163 SCREW #10 3
543 WE1M462 SLEEVE DRUM 1
552 WE4X448 FLAME DETECTOR 1
603 WE1M482 HANDLE DOOR CC 1
610 WE9M13 GASKET 1
630 WE17M22 MOTOR & PULLEY ASM. 1
709 WE01X1148 ORIFICE 1
710 WE01X1076 LEAK LIMITER 1
711 1/8-27 NPT PLUG PIPE (NOT STOCK) 1
712 WE14X0215 GAS VALVE ASM 1
713 WE14X215 VALVE ASM. SHUTOFF 1
714 WE1M512 PIPE & LUG 1
716 WE14X217 BURNER ASM. 1
717 WE04X0739 IGNITER ASM 1
721 WE13X0118 BRACKET SPACER 1
723 WE13X0195 BRACKET GAS VALVE 1
729 WE04X0692 COIL DUAL 1
730 WE02X0333 SCREW (COIL MTG BRKT) 2
731 WE04X0693 COIL MAIN 1
732 WE13X0169 BRKT. COIL 1
803 WD21X0557 SWITCH INTERLOCK 1
875 WD2M101 SCREW 6732 WE13X0169 BRKT. COIL 1
907 WD09X0206 PUSHBUTTON 4
1254 WE2M199 PLATE SECUR FRT CAB 1
3046 WE2M170 SCREW #8 10
3049 WE01X1192 STRIKE DOOR 1
907 WD09X0206 PUSHBUTTON 4
3051 WE1M505 HINGE 2
3102 WE1M300 BEARING RETAINER 1
3104 WE2M180 SCREW 1
3109 WE2M154 SCREW 8
3118 WE2M174 SCREW # 10 8
3127 WE1M461 O RING 1
DCCD330GD-COUNTDOWN
VIEW CAT. # DESCRIPTION QTY.
29
DCCB330ED/DCCD330ED
316 313 1254
312 327
3046
311
325
380
303302 300 14
323
3049
3046
603
307
305
3051
3046610301
FRONT PANEL DCCB330ED/DCCD330ED
ELECTRIC NON-COUNTDOWN MODELDCCB330ED
22 155 21 907 35
38213
157
168100
397See Breakdown Page
172
4891483130
396
1
4
727580
7692
875
1553
22
382
155 21 907 353
87575
155
10 23
757280120
7692 4
1
396
4891483130
168100
397
172
ELECTRIC COUNTDOWN MODELDCCD330ED
30
DCCB330ED/DCCD330ED
227
75
222
178
241240
420
235
430
3204
235431
419
404
410
236
405
408
405
404
403
401
ELECTRIC CABINET/DCCB330ED/DCCD330ED
204
231
3104
205
3109
203
630
228
3109
230
218
201
202199
502
232
233
239803
216213
215
BLOWER ASSEMBLY DCCB330ED/DCCD330ED
31
515 3102 506
505
512 507510
4053127
543508
504
534
509
503
502
ELECTRIC DRUM ASSEMBLY +
DCCB330ED/DCCD330ED
32
VIEW CAT. # DESCRIPTION QTY.
DCCB330ED-NON CNTDWN
1 31-16073 INSTR INSTALL 1
1 31-16086 MINI-MANUAL 1
1 49-90162 USE & CARE GEA COIN 1
3 WE19M938 END CAP LH BK 1
4 WE19M939 END CAP RH BK 1
13 WE19M1361 SWITCH TRIM COIN 1
14 WH02X1151 CLIP GROUND 3
30 WE1M533 PLATE SECUR COIN BOX 1
35 WE4M210 P.B. SWITCH 1
72 WE20X811 REAR PANEL 1
75 WE2M173 SCREW 2
80 WE4M307 RESIS. (3.5K OHM) BEIGE 1
100 WH65M185 TIMER & BRACKET ASM 1
112 WR02X10459 PLUG DOOR RVSBL BQ 4
148 WE2M183 BOLT 1/4" 1
155 WH02X1233 SCR 8-18 AB TRT 5/8 S 15
157 WE1X950 LAMP ASM. - AMBER 1
168 WZ02X0468 SCR 10-32 M HS 1/8 S 2
168 WZ2X468D SCR 10-32 M HS 1/8 S 2
172 WH02X0735 SCR 1/4-20 M SH .900 CS 3
173 WE2M182 WASHER LOCK 3
172 WH2X735D SCR 1/4-20 M SH .900 CS 3
178 WE2M175 SCREW # 8 4
199 WE2M98 SCREW 1
201 WE1X306 BLOWER WHEEL 1
202 WE1M532 DEFLECTOR 1
203 WE13X0200 STRAP MOTOR 2
204 WE01X0921 STRAP MOTOR 1
205 WE13M36 MOTOR SUPPORT 1
213 WE12M22 BELT DRIVE 1
215 WE3M17 IDLER ARM 1
216 WE12M8 IDLER PULLEY 1
218 WE14M93 BLOWER HOUSING 1
222 WE20M321 BOTTOM COVER COIN 1
227 WE13M26 SHEILD 1
228 WE14M90 PIPE EXAUST 1
230 WE4M311 TSTAT OUTLET BIASED 1
231 WE2M187 SCREW 1
232 WE2M156 SCREW 2
233 WE13M35 MOTOR PLATE (E-COAT) 1
234 WE2M96 CAP NUT 1
235 WE1M280 SCREW 18
236 WE1M368 LEVELLING SCREW 4
239 WE2M167 SCREW 2
240 WH01X2266 BUTTON PLUG 1
241 WH01X2268 RETAINER BUTTON 1
300 WE18M21 FILTER FRAME COIN 1
301 WE20M323 FRT PNL COIN BISQUE 1
302 WE2M189 SCREW 2
303 WE2M181 RUBBER WASHER 2
307 WE10M104 PANEL OUTER CC 1
311 WE14M92 AIR DUCT ASM. 1
312 WE9M15 FELT 1
313 WE3M20 TOP BEARING 1
316 WE1M415 BEARING-SLIDE GREEN 2
316 WE1M504 BEARING-SLIDE WHITE 2
323 WE1M416 PLUG BUTTON 1
325 WE00M169 GASKET (SEAL) 1
326 WE1M473 GASKET SEAL 1
327 WE1M187 LATCH 2
380 WE4M126 DOOR SWITCH 1
382 WH42X10399 DOOR & LATCH ASM 1
396 WE1M534 ADAP. METER CASE 1
397 WE1M535 METER CASE 1
401 WE20M322 COVER COIN BISQUE 1
403 WE02X0405 SCR 8-18 AB OVT 2S 6H 4
404 WE20M310 PANEL SIDE CC 2
405 WE2X263 SCREW 12
408 WE20M320 BASE CABINET COIN 1
410 WE1M467 LEVELLING LEG & BRKT 2
410 WE1M527 FRT BRKT LEVEL LEG 2
410 WE1M528 REAR BRKT LEVEL LEG 2
410 WE1M468 LEVELLING LEG & BRKT 2
419 WE4M304 TERM BLOCK & GRD ST 1
420 WE20M300 PANEL REAR 7 CU FT 1
421 WE1M155 CORD CLIP 1
430 WE1M458 TERM. BLOCK COVER 1
431 WE1M457 STRAIN RELIEF BRKT 1
489 WH01X2572 SLEEVE SPLIT 1
502 WE2M174 SCREW #10 9
503 WE21M13 DRUM ASM 7.0" 1
504 WE14M77 DIFFUSER 1
505 WE4M160 TSTAT , SAFETY LEFT 1
506 WE4M309 TSTAT INLET BLUE 1
507 WE4M137 TSTAT HI-LIMIT 1
508 WE3X39 SHAFT & BRKT ASSY 1
509 WE14M75 BAFFLE 3
510 WE1M452 CER. COIL SUPPORT 6
512 WE11M27 HEATER ASM. COIN 1
515 WE01X1172 GROUND STRAP ASM 1
534 WE2M163 SCREW #10 3
543 WE1M462 SLEEVE DRUM 1
603 WE1M482 HANDLE DOOR CC 1
610 WE9M13 GASKET 1
630 WE17M22 MTR & PULLEY ASM. 1
803 WD21X0557 SWITCH INTERLOCK 1
DCCB330ED-NON CNTDWNVIEW CAT. # DESCRIPTION QTY.
33
907 WD09X0206 PUSHBUTTON 4
1254 WE2M199 PLATE SECUR FRT CAB 1
3046 WE2M170 SCREW #8 10
907 WD09X0206 PUSHBUTTON 4
3049 WE01X1192 STRIKE DOOR 1
3051 WE1M505 HINGE 2
3102 WE1M300 BEARING RETAINER 1
3109 WE2M154 SCREW 1
3118 WE2M174 SCREW # 10 8
3127 WE1M461 O RING 1
3204 WH2M270 SCREW 2
VIEW CAT. # DESCRIPTION QTY.
VIEW CAT. # DESCRIPTION QTY.
DCCD330ED-COUNTDOWN
1 31-16073 INSTR INSTALL 1
1 31-16091 MINI-MANUAL 1
1 49-90162 USE & CARE 1
3 WE19M938 END CAP LH BK 1
4 WE19M939 END CAP RH BK 1
10 WE4M313 CNTL COIN-OP ASM 1
13 WE19M1372 SWITCH TRIM ASM 1
14 WH02X1151 CLIP GROUND 3
23 WE5M20 HARNESS CNTDN CNTL 1
30 WE1M533 PLATE SECUR COIN BOX 1
35 WE4M210 P.B. SWITCH 1
72 WE20X811 REAR PANEL 1
75 WE2M173 SCREW 4
80 WE4M307 RESIS (3.5KOHM) BEIGE 1
100 WH65M185 TIMER & BRACKET ASM 1
112 WR02X10459 PLUG DOOR RVSBL BQ 4
120 WH01X10072 PCB COVER COIN-OP 1
148 WE2M183 BOLT 1/4" 1
155 WH02X1233 SCR 8-18 AB TRT 5/8 S 15
157 WE1X950 LAMP ASM. - AMBER 1
168 WZ02X0468 SCR 10-32 M HS 1/8 S 2
168 WZ2X468D SCR 10-32 M HS 1/8 S 2
172 WH02X0735 SCR 1/4-20 M SH .900 CS 3
173 WE2M182 WASHER LOCK 3
172 WH2X735D SCR 1/4-20 M SH .900 CS 3
178 WE2M175 SCREW # 8 4
199 WE2M98 SCREW 1
201 WE1X306 BLOWER WHEEL 1
202 WE1M532 DEFLECTOR 1
203 WE13X0200 STRAP MOTOR 2
204 WE01X0921 STRAP MOTOR 1
205 WE13M36 MOTOR SUPPORT 1
213 WE12M22 BELT DRIVE 1
DCCB330ED-NON CNTDWNVIEW CAT. # DESCRIPTION QTY.
215 WE3M17 IDLER ARM 1
216 WE12M8 IDLER PULLEY 1
218 WE14M93 BLOWER HOUSING 1
222 WE20M321 BOTTOM COVER COIN 1
227 WE13M26 SHEILD 1
228 WE14M90 PIPE EXAUST 1
230 WE4M311 TSTAT OUTLET BIASED 1
231 WE2M187 SCREW 1
232 WE2M156 SCREW 2
233 WE13M35 MTR PLATE (E-COAT) 1
234 WE2M96 CAP NUT 1
235 WE1M280 SCREW 18
236 WE1M368 LEVELLING SCREW 4
239 WE2M167 SCREW 2
240 WH01X2266 BUTTON PLUG 1
241 WH01X2268 RETAINER BUTTON 1
300 WE18M21 FILTER FRAME COIN 1
301 WE20M323 FRT PN COIN BISQUE 1
302 WE2M189 SCREW 2
303 WE2M181 RUBBER WASHER 2
305 WE10M105 PANEL DR INNER CC 1
307 WE10M104 PANEL OUTER CC 1
311 WE14M92 AIR DUCT ASM. 1
DCCD330ED-COUNTDOWN
313 WE3M20 TOP BEARING 1
316 WE1M415 BEARING-SLIDE GREEN 2
316 WE1M504 BEARING-SLIDE WHITE 2
323 WE1M416 PLUG BUTTON 1
325 WE00M169 GASKET (SEAL) 1
326 WE1M473 GASKET SEAL 1
327 WE1M187 LATCH 2
380 WE4M126 DOOR SWITCH 1
382 WH42X10399 DOOR & LATCH ASM 1
396 WE1M534 ADAPT METER CASE 1
397 WE1M535 METER CASE 1
401 WE20M322 COVER COIN BISQUE 1
403 WE02X0405 SCR 8-18 AB OVT 2S 6H 4
404 WE20M310 PANEL SIDE CC 2
405 WE2X263 SCREW 12
408 WE20M320 BASE CABINET COIN 1
410 WE1M467 LEVELLING LEG & BRKT 2
410 WE1M527 FRONT BRKT LEVEL LEG 2
410 WE1M528 REAR BRKT LEVEL LEG 2
410 WE1M468 LEVELLING LEG & BRKT 2
419 WE4M304 TERM BLOCK & GRD ST 1
420 WE20M300 PANEL REAR 7 CU FT 1
421 WE1M155 CORD CLIP 1
430 WE1M458 TERM. BLOCK COVER 1
431 WE1M457 STRAIN RELIEF BRKT 1
34
489 WH01X2572 SLEEVE SPLIT 1
502 WE2M174 SCREW #10 9
503 WE21M13 DRUM ASM 7.0" 1
504 WE14M77 DIFFUSER 1
505 WE4M160 TSTAT , SAFETY LEFT 1
506 WE4M309 TSTAT INLET BLUE 1
507 WE4M137 TSTAT HI-LIMIT 1
508 WE3X39 SHAFT & BRKT ASSY 1
509 WE14M75 BAFFLE 3
510 WE1M452 CERAMIC COIL SUPP 6
512 WE11M27 HEATER ASM. COIN 1
515 WE01X1172 GROUND STRAP ASM 1
534 WE2M163 SCREW #10 3
543 WE1M462 SLEEVE DRUM 1
603 WE1M482 HANDLE DOOR CC 1
610 WE9M13 GASKET 1
630 WE17M22 MTR & PULLEY ASM. 1
803 WD21X0557 SWITCH INTERLOCK 1
907 WD09X0206 PUSHBUTTON 4
1254 WE2M199 PLATE SECUR FRT CAB 1
3046 WE2M170 SCREW #8 10
907 WD09X0206 PUSHBUTTON 4
3049 WE01X1192 STRIKE DOOR 1
3051 WE1M505 HINGE 2
3102 WE1M300 BEARING RETAINER 1
3109 WE2M154 SCREW 1
3118 WE2M174 SCREW # 10 8
3127 WE1M461 O RING 1
3204 WH2M270 SCREW 2
DCCD330ED-COUNTDOWN
VIEW CAT. # DESCRIPTION QTY.
35
36
notes
__________________________________________________________________________________________________
______________________________________________________________________________________
_____________________________________________________________________________________
_______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
_________________________________________________________________________________________
________________________________________________________________________________________
__________________________________________________________________________________________
________________________________________________________________________________________
_____________________________________________________________________________________
__________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
_________________________________________________________________________________________
___________________________________________________________________________________________
_________________________________________________________________________________________
________________________________________________________________________________________
______________________________________________________________________________________
_________________________________________________________________________________________
________________________________________________________________________________________
__________________________________________________________________________________________
________________________________________________________________________________________
Top Related