Remove sample for personal testing

*Colors are approx.TECHNICAL DATA

cut space

NAVY MIL SPEC MIL-PRF 32171A HIGH DURABILITY DECK COATINGS

TEST SPEC. REQUIREMENT CRITERIA RESULTSToxicity Health Hazard Assessment NEHC (Navy Environmental Health Center)

Asbestos content 29 CRF 1915, 1001, appendix K < 5% by wt dry coating

Metal content 40 CRF 261 < all metals in table

Volume solids ASTM D2697 71.2%

VOC 40 CRF 60 250 g/l

Flash Point ASTM D3278 122°F

Shelf Life ASTM D1849 + 12 mos.

Drying/cure time FED-STD-141, method 4061 90 min / service 6-12 hrs.

Abrasion Resistance ASTM D4060 30.5 mg loss

Impact Resistance ASTM D2794 Not less than 50 in. lbs.

Flexibility ASTM D6905 No checking, cracking or flaking.

Pencil Hardness ASTM D3363 2 H to 3 H

Slip Resistance ADTM D2047 Dry 1.21 / Wet 0.67

HAP Content ASTM E260 or Methods 7356 and 7360, < values in Table III

(Hazardous Air Polutants) and ASTM E1252 Condition in Container 3011.2 of FED-STD 141 Resistance to Water ASTM D1308 No effect

Resistance to HC Fluid ASTM D1308 No effect

Resistance to Salt Spray ASTM B117 and ASTM D610 No effect

Resistance to Condensation ASTM D2247 and ASTM D714 No effect

Pot Life Navy test 3 hours

Gloss ASTM D 523 84.7%

Extent of Corrosion ASTM D610-01 No corrosion

Degree of Blistering ASTM D714-02 No blistering

Salt water resistance 100% Freeze-thaw resistance -60˚ F to +254˚ F Pot life 3 hours Shelf life 1 year Flash time avg. 1-1/2 to 3 hours Walk time 6 to 12 hours Time between coats approx. 1 hour Full cure 4 days VOC 250 g/l DOT Hazmat Info. Paint , 3, UN1263, PG III Coverage 60 s/f per gal w/2 coats Ideal Storage 32˚ F to 104˚ F Flash point 122˚ F

Weight per gallon, pounds 10 Viscosity, Kreb units 67-72 Percent solids by weight 66% Application temperature range 32˚ F to 95˚ F (NOTE: On nonporous surfaces, below 32˚ F)

Application thickness, 2 coats dry approx. 24 mils Flexibility total �exibility Resilience resilient in dry state Abrasion Resistance Tabor Wheel, 1000 gr load, 1000 cycles 30.5 Fire resistance Flame spread ASTM E-162: 01 Smoke generation ASTM E662: 06

Totally �exible and stretchable – no cracking Bonds to metal, concrete, wood, �berglass, etc. Very light weight – less than 1 oz/sf/coat Extremely durable Slip resistant Also available in smooth version DURABAK - M26™ for indoor use DURABAK 18 - M26™ for outdoor use Salt spray resistant Used on outdoor weather decks Repairable – bonds to itself without removing old coating One-part UV, acid, chemical, and weather resistant Waterproof – no membrane primer needed Repairable at sea Fire retardant Corrosion and abrasion resistant Heat resistant – constant 254°F Sound deadening Electrical conductivity resistant Easy to apply by roller, brush, or spray Self-leveling application Fast dry and inter coat times Available in over 16 colors Environmentally friendly Low VOCs Incorporates recycled rubber granules When cured, non-HAZMAT disposal (check local regulations) Encapsulates lead paint

PRODUCT FEATURES

Durabak - M26™ qualifies for Type I Interior Decks and Type III Outdoor Weather Decks

If your sample is missing,please call us at:

201.836.0733