THAR-VW2 & TB-VW STAND ALONE INSTALLATION … · passat 2012-2017 • • • • • • • •...
Transcript of THAR-VW2 & TB-VW STAND ALONE INSTALLATION … · passat 2012-2017 • • • • • • • •...
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20171106
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20171106
ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.COMPATIBLE AVEC VÉHICULE À TRANSMISSION AUTOMATIQUE SEULEMENT.
FLASH LINK UPDATER FLASH LINK UPDATER
1XMicrosoft Windows Computer &Internet connection
Ordinateur Microsoft Windows & connection Internet
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)
VEHICLEVEHICULES
YEARS ANNÉES Im
mob
ilize
r byp
ass
with
TB
-VW
(S
old
sepa
rate
ly)
Con
tour
nem
ent d
’imm
obili
sate
ur
avec
TB
-VW
(Ven
du s
épar
émen
t)
THA
RN
ESS
HA
RN
AIS
EN
T
Lock
Unl
ock
Arm
Dis
arm
Tach
omet
er
Haz
ard
Ligh
ts
Trun
k - o
pen
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s *
Han
d-B
rake
Sta
tus
Foot
-Bra
ke S
tatu
s
OEM
Rem
ote
mon
itorin
g
VOLKSWAGENPassat 2012-2017 • • • • • • • • • • • • • • •
Guide # 62471
PUSHSTART
PUSHSTART
PUSHSTART
PUSHSTART
NOTES
* Hood Status Hood Status : functional if equipped with a factory hood switch. HOOD STATUS : fonctionnel si équipé d’un commutateur de capot d’origine.
HARDWARE VERSIONVERSION MATÉRIELLE
FIRMWARE VERSIONVERSION LOGICIELLE This manual may change without notice.
www.fortinbypass.com for latest version.Ce Guide peut faire l’objet de changement
sans préavis. www.fortinbypass.com pour la récente version.
MINIMUM 6 75.[36]VW MINIMUM
Program bypass option:Programmez l’option du contournement:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote status (Lock/Unlock) monitoringSuivi des status (Verrouillage/Déverrouil-lage) de la télécommande d’origine
Program bypass option(If equiped with OEM alarm):
Programmez l’option du contournement(Si équipé d’une alarme d’origine):
UNIT OPTIONOPTION UNITE DESCRIPTION
D2Unlock before / Lock after (Disarm OEM alarm)Déverrouille avant / Verrouille après (Désarme l’alarme d’origine)
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))
1x TB-VW1x THAR-VW2
1x TB-VW1x THAR-VW2
FLASH LINK MANAGERSoftware version 3.63 and more
FLASH LINK MANAGERVersion logicielle 3.63 et plus
THAR-VW2 & TB-VW STAND ALONE INSTALLATIONINSTALLATION AUTONOME THAR-VW2 & TB-VW
Page 1 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
PARTS REQUIRED (NOT INCLUDED) | PIÈCES REQUISES (NON INCLUSES)
STAND ALONE CONFIGURATION | CONFIGURATION EN DÉMARREUR AUTONOME
FLASH LINKUPDATER 2
FLASH LINK MANAGER
OFF
ON
SOFTWARE | PROGRAMME
Microsoft Windows Computer(Internet connection required)Ordinateur Microsoft Windows(Connection Internet requise)
HOOD PIN
VALET SWITCHCOMMUTATEUR VALET
REMOTE START SAFETY OVERRIDE SWITCH
CONTACTDECAPOT
COMMUTATEUR DE SÉCURITÉ DE DÉSACTIVATION DU DÉMARREUR À DISTANCE
MANDATORY | OBLIGATOIRENotice: the installation of safety elements are mandatory.The hood pin and the valet switch are essential security elements and must be installed.
Notice: l'installation des éléments de sécurité est obligatoire.Le contact de capot et le commutateur de valet sont des éléments de sécurité essentiels et doivent absolument être installés.
Part #: RSPB availbale, Sold separately.Pièce #: RSPB disponible, vendu séparément.
Program bypass option:Programmez l’option du contournement:
UNIT OPTIONOPTION UNITE DESCRIPTION
D1OEM Remote Stand Alone Remote StarterDémarreur à distance Autonome avec télécommande d’origine
UNIT OPTIONOPTION UNITE DESCRIPTION
D4Hybrid mode (Vehicle hybrid only)Mode hybride (vehicule hybride seulement)
Program bypass option with oem remote:Programmez l’option du contournement
avec télécommande d'origine:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote Monitoring
Supervision de la télécommande d'origine
Program bypass option with RF KIT antenna:Programmez l’option du contournement
avec antenne RF:
Program bypass optionVehicle hybrid only:
Programmez l’option du contournementvehicule hybride seulement:
UNIT OPTIONOPTION UNITE DESCRIPTION
H1 to H6H1 à H6
Supported RF Kitsand select RF KitKit RF supportéset sélectionnez le KIT RF
All doors must be closed.
Toutes les portes doivent être fermées
Brake ON No tach Ignition before start
Hood Open
Frein ActivéPas de TachClé de contact détectée avant démarrage Capot Ouvert
REMOTE STARTER DIAGNOSTICSDIAGNOSTIQUE DU DÉMARREUR À DISTANCEMODULE RED LED | DEL ROUGE DU MODULEx2 �ash : x3 �ash : x4 �ash :
x5 �ash :
The vehicle will START.
Le véhicule DÉMARRE.
START3XPress the OEM remote’s Lock button 3x to remote-start (or remote-stop) the vehicle.
Appuyez sur le bouton Verrouillage 3X de la télécommande d'origine pour démarrer à distance (ou
arrêter à distance) le véhicule.
REMOTE STARTER FUNCTIONNALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
REMOTE STARTER WARNING CARD | CARTE D'AVERTISSEMENT DE DÉMARREUR À DISTANCE
CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE:or use the package RSPB, Sold separately.
COUPEZ CETTE CARTE D'AVERTISSEMENT ET COLLEZ-LA À UN ENDROIT VISIBLE:ou utilisez la trousse RSPB, vendue séparément.
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON
ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A
SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE
DASHBOARD BEFORE WORKING ON THE VEHICLE.
LE VÉHICULE PEUT DÉMARRER SOIT: EN APPUYANT 3 FOIS CONSÉCUTIVEMENT SUR
LE BOUTON VERROUILLAGE DE LA TÉLÉCOMMANDE DU VÉHICULE OU PAR UN TÉLÉPHONE INTELLIGENT. ACTIONNEZ EN
POSITION ‘ON’ LE COMMUTATEUR DE SÉCURITÉ SITUÉ SOUS LE TABLEAU DE BORD
AVANT LES TRAVAUX D'ENTRETIEN.
DÉMARREUR À DISTANCEREMOTE STARTER
WARNING | ATTENTION
Page 2 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
(+)IGNITION
(+) 12V (+) STARTER
Ignition HarnessHarnais d'ignition
Ignition barrelBarillet d'ignition
(~) CAN High (~) CAN Low
(+)IGNITION
(+) 12V (+) STARTER
Ignition HarnessHarnais d'ignition
Transponder wire
Ignition barrelBarillet d'ignition
Black loomGaine Noire
(~) CAN1 HIGH (~) CAN1 LOW
OBD-II connectorConnecteur OBD-II
6
(~)CAN2 HIGH
14
(~)CAN2 LOW
BCM
(-) HAZARD(-) HAZARD(+)FOOT BRAKE
Page 3 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Y����� In A1 P����� In A2
P�����/W���� In A3 G���� Out A4 W���� Out A5
O����� In A6 O�����/B���� In A7
D�.B��� In A8 R��/B��� In A9
L�.B���/B���� A10 B���� Out A11
P��� Out A12 Y�����/B���� In A13 B����/W���� Out A14
P���/B���� Out A15 P�����/Y����� A16
G����/W���� A17 G����/R�� A18
W����/B���� A19 L�.B��� A20
C5 B���� C4 G���/B���� C3 G��� C2 O�����/B���� C1 O�����/G����
D6 W����/R�� D5 W����/B��� D4 W����/G���� D3 Y�����/R�� D2 Y�����/B��� D1 Y�����/G����
A C
D
AUTOMATIC TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION AUTOMATIQUE
Y�����/G����
W����/G����W����/B���W����/R��
B����
W����/B����G����/R��
G����/W����
P���/B���� Out(-)Hazards
P��� Out
R��/B��� In
O�����/B���� InO����� In
W���� OutG���� Out
(+)IgnitionB
WITH DATA-LINK:AVEC DATA-LINK:
WITH D2D:AVEC D2D:
OROU WITH | AVEC DATA-LINK:
Direct connectionBranchement directe
RF-KIT REMOTESTARTER
KIT-RF DÉMARREURÀ DISTANCE
OPTIONAL RF KITKIT RF OPTIONNEL
CAN 1 LOWCAN 1 HIGHCAN 2 LOWCAN 2 HIGH
(-) Unlock(-) Lock
(-) Lock/Unlock input external control | Contrôle du (-) verrouillage devérrouillage entrée externe
Start / Stop external controlContrôle de démarrage/arrêt externe
Start/Stop external
Hood pin
SAFETY OVERRIDE SWITCHCOMMUTATEUR DE SÉCURITÉ
Hood pin only required on vehicles not equipped with a factory hood pin.Commutateur de capot requis seulement si le véhicule n'est pas équipé de cette composante.
TB-VWSOLD SEPARATELY
VENDU SÉPARÉMENT
MAL
ET-
HAR
NES
SIG
NIT
ION
PLU
GC
ON
NEC
TEU
R D
’IGN
ITIO
ND
UT-
HAR
NAI
SM
ÂLE
MAL
EVE
HIC
LEIG
NIT
ION
PLU
GC
ON
NEC
TEU
R M
ÂLE
D’IG
NIT
ION
DU
VÉH
ICU
LE
FEM
ALE
T-H
ARN
ESS
IGN
ITIO
N P
LUG
CO
NN
ECTE
UR
D’IG
NIT
ION
DU
T-H
ARN
AIS
FEM
ELLE
T-H
AR
NES
S - H
AR
NA
IS E
N T
-
TH
R-V
W2
White/Red or Green
White/Green or Green/Black
Cut
TRANSPON-DER WIRE
Twisted pair in a Black loom from key reader located arround Ignition barrel.
Paire de Fils torsadés dans une gaine Noire provenant
du lecteur de clé situé autour du Barillet de l'ignition.
Cut one of the 2 wiresCoupez l'un des 2 fils
NE PAS RALLONGER LES FILS (6 pouces max.)
DO NOT EXTEND THE WIRES (6 inches max).
Orange/BrownOrange/Brun
C2C1(~)CAN2 HIGH
(~)CAN2 LOW
1
9 10
2 3 4 5 7 8
11 12 13 14 15 16
66
14
OBDIIFront view
Vue de face
Orange/BlackOrange/Noir
Yellow/Red | Jaune/Rouge BRAKE OUT
*CONNECT ONLY IF BRAKE MUST BE
PRESSED TO START*BRANCHEZ
SEULEMENT SI LE FREIN DOIT ÊTRE
APPUYÉ AU DÉMARRAGE
ISOLATENOT CONNECTED---------------------ISOLERNON BRANCHÉ
Yellow | Jaune IGNITION OUT
CO
NN
ECT
BR
AN
CH
ER
BCM connector, Brown cover Under
the dash Driver side, Brown 52-PINS
connector - Back view
Connecteur BCM, Couvert Brun, Sous le tableau de bord
côté chauffeur Connecteur Brun de 52 pins - Vue de dos
5432 10987
12 13 14 15 16 18 19 20 21 22 23 24
25 26 27 28
29 30 31 32 33 34 35 36 37 38 39 40 41
1161
46454443 51504948 524742
7
17
Brown/RedBrun/Rouge
A14(-)HAZARD
OPTIONALFACULTATIF
7
(+)FOOTBRAKE*Black/RedNoir/Rouge
17
Page 4 / 9
5
6
1
3
4
2
11
Press and hold the programming button.
Appuyez et gardez enfoncé le bouton de programmation.
Release the programming button.
Relâchez le bouton de programmation.
Connect the required remaining harnesses.
Branchez les harnais requis restants.
Release the programming button when the Blue LED is ON.
Relâchez le bouton de program-mation quand la DEL Bleue est allumée.
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Les DELs Bleue, Rouge, Jaune et Bleue & Rouge illumineront alternativement.
The BLUE LED will flashrapidly.
La DEL BLEUE clignoterarapidement:
The BLUE LED will turn OFF. La DEL BLEUE s'éteint.
The RED LED will turn ON. La DEL ROUGE s'allume.
Wait, Attendez,
Wait, Attendez,
WARNING:Close and open the driver door.
ATTENTION:Fermez et ouvrez la porte conducteur.
LOCK
ACC ON
PUSH
START
IGN
TURNON/RUN Tournez la clé à Ignition.Turn the key to the
Ignition ON/RUN position.
HOLD
x1PRESS
RELEASE
If the LED is not solid BLUE disconnect the 4-PIN Data-link harness (Black connector) and go back to step1.
Si la DEL Bleue n’est pas allumée, débranchez le harnais Data-Link à 4-Broches (connecteur Noir) et retournez au début de l'étape 1.
ON BLUEBLEU
PRESS - HOLD
x1HOLD
Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
Appuyez et maintenir le bouton de programmation enfoncé: Branchez le harnais Data-Link à 4-Broches (connecteur Noir)
OFF
ON
WAIT3 SEC.
RELEASE
WAIT
OFF
FLASHRAPIDLY
IGNITION OFF IGNITION ON
ON
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTOR
Parts required (not included) Pièces requises (non incluses)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER software1x Microsoft Windows Computer with Internet connection
1x FLASH LINK UPDATER, 1x Programme FLASH LINK MANAGER1x Ordinateur Microsoft Windows avec connection Internet
Page 5 / 9
7
Wait, Attendez,
Wait, Attendez,
the RED LED to turn ON. DEL ROUGE s'allume.
Wait, do not touch the vehicle or the module.
Attendez, ne touchez pas au véhicule ou au module.
The BLUE, RED and YELLOW LEDs will rapidly alternate.
Les DELs BLEUE, ROUGE et JAUNE alternent rapidement.
Wait for the RED and YELLOW LEDs to slowly alternate.
Attendez que les DELs ROUGE et JAUNE alternent doucement.
19
18
WAIT,this processe may take up
to 15 minutes
Attendez,ce processus peut prendre
jusqu’à 15 minutes
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.
Si la DEL ROUGE clignote lentement, la programmation a échoué, recommencez à l'étape 1.
LOCK
ACC ON
PUSH
START
OFFF
TURNOF
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
...
...
...
ON
EVO-ALL
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite le connecteur Data-Link (4-pins).
FLASH LINKUPDATER 2
FLASH LINKUPDATER 2
FLASH LINK MANAGERSOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connectionOrdinateur Microsoft Windows avec connection Internet
Parts required (not included)Pièces requises (non incluses)
Connect the module to the FLASH LINK UPDATER 2 and visit the DCryptor menu in the Flash-Link Manager.
Branchez le module au FLASH LINK UPDATER 2et visitez le menu DCryptor dans le Flash-Link Manager.
AFTER DCRYPTOR PROGRAMMING COMPLETEDGo back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION DCRYPTOR COMPLETÉE : retournez au véhicule etrebranchez le connecteur 4-pins (Data-Link) et après, tous les connecteurs du EVO-ALL.
EVO-ALL
10
11
12
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/4 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/4Page 6 / 9
The RED and YELLOW LEDswill alternate.
La DEL ROUGE et JAUNEalternent.
114
The YELLOW LED will turn OFF. La DEL JAUNE s’éteint.
115
2/2
113
The RED and YELLOW LEDsturn ON.
The RED and YELLOW LEDsstay OFF.
Les DELs ROUGE et JAUNErestent éteintes.
The module is now programmed.Le module est programmé
.
Les DELs ROUGE et JAUNE s’allument.
CONTINUED BELOWCONTINUEZ CI-DESSOUS
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
OROU
LOCK
ACC ON
PUSH
START
IGN
TURNON/RUN
Tournez la clé à Ignition.Turn the key to theIgnition ON/RUN position.
LOCK
ACC ON
PUSH
START
OFFF
TURNOF
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
ONON
ON
WAIT3 SEC.
IGNITION ONIGNITION OFF
ONON
OFFOFFOFF
AFTER HAVING PLUGGED IN THE DATA-LINK CONNECTOR AND THE REQUIRED REMAINING HARNESSES: :APRÈS AVOIR BRANCHER LE CONNECTEUR DATA-LINK ET LES HARNAIS REQUIS RESTANTS :
FLASH LINKUPDATER 2
Connect the module to the FLASH LINK UPDATER 2 and visit the DCryptor menu in the Flash-Link Manager.
Branchez le module au FLASH LINK UPDATER 2et visitez le menu DCryptor dans le Flash-Link Manager.
RECOMMENCERTRY AGAIN
ENVOYER DONNÉESSEND DATA
EVO-ALL
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite le connecteur Data-Link (4-pins).
16
17
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 3/4 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 3/4Page 7 / 9
AFTER DCRYPTOR PROGRAMMING COMPLETEDGo back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION DCRYPTOR COMPLETÉE : retournez au véhicule etrebranchez le connecteur 4-pins (Data-Link) et après, tous les connecteurs du EVO-ALL.
EVO-ALL
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
18
NOTE NOTESI LA PROGRAMMATION EST INTERROMPUE DURANT SON PROCESSUS, COMME PAR UN DÉBRANCHEMENT DU MODULE OU PAR LA FERMETURE DE LA CLÉ DE CONTACT, IL EST POSSIBLE QUE LE VÉHICULE NE PUISSE PLUS DÉMARRER NORMALEMENT, VOUS DEVREZ DÉBRANCHER ET REBRANCHER LA BATTERIE DU VÉHICULE POUR CORRIGER LA SITUATION.
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT THE VEHICLE BATTERY TO CORRECT THE SITUATION.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 4/4 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 4/4Page 8 / 9
ALL
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2014, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
EVO-ALL
Page 9 / 9