Specialized Solutions for Fiber Optic Testing

www.optotest.com 1.805.987.1700

OP735

The OptoTest OP735 Benchtop Optical Power Meter can be configured with up to 4 channels and a mix of InGaAs, Silicon, and High-Power Detectors. This unit is ideal as a compact, stand-alone power meter or used in conjunction with a stabilized light source to measure insertion loss.

Designed for high-speed data acquisition on fiber optic components, the OP735 provides absolute or relative measurements with high resolution and tight linearity specifications.

Multichannel Optical Power Meter

OP740

The OP740 offers a state-of-the-art solution for high-speed optical power measurement applications where multiple channels are needed. Unlike many other systems, this instrument is comprised of individual power meters allowing for simultaneous data acquisition over all channels with unparalleled speed.

High-Speed Multichannel Optical Power Meter

1mm InGaAs 3mm Silicon

Sampling Speed variable, max 125,000 samples/secondMeasurement Range +6dBm to -72dBm at 1490nm +3dBm to -65dBm at 980nmWavelength Spectrum 830nm to 1700nm 400nm to 1100nmRelative Accuracy ±0.02dBChannel Count Up to 24 in one 2U enclosure

OP

74

0

OP-METS

The OP-METS Multichannel Environmental Test Station is optimized for environmental testing of up to 144 single mode or multimode fiber assemblies or passive components.

Key Benefits• Facilitates environmental testing per

GR-326-CORE, GR-1435-CORE

• Qualify single fiber (FC, SC, LC, etc) or multifiber connectors (MPO/MTP, MXC, PRIZM-LT, etc)

• Multimode and Single Mode Wavelengths 850 / 1300 / 1310 / 1490 / 1550 / 1625

• Multimode IL sources can be configured to meet IEC/TIA specifications (Encircled Flux) – upon request

• Stability testing with flexibility for unique configurations

• Unparalleled insertion loss (IL) stability

Multichannel Environmental Test Station

For complete specifications visit www.optotest.com

OP710

The OP710 offers an economical approach for optical power measurement applications where multiple channels are needed. Unlike other systems, this instrument is built up with individual power meters allowing for unparalleled simultaneous data acquisition over all channels.

The OP710 is available with up to 24 channels and can be configured for an assortment of detector and connector interfaces. With the rack mount option, multiple instruments can be combined and configured for even higher channel counts.

Multichannel Optical Power Meter

OP1100Discontinuity AnalyzerThe OP1100 Discontinuity Analyzer is an off-the-shelf fiber optic test system that automatically captures, displays and logs short optical power interruptions and spikes in accordance with EIA/TIA-FOTP-32A.

This test solution provides a method for testing a broad variety of passive or active fiber optic components for susceptibility to discontinuities (signal dropout, transient output or transmittance fluctuations) during application of an external stimulus, such as temperature, vibration or physical shock.

For channel counts greater than 4, a purchase of the OP1100 includes the OP710-ANX Multichannel Optical to Electrical Converter.

Optical Power Meter Input power range: -2dBm to -40dBmWavelength Range: 830nm to 1650nm

Optical Receiver300μm InGaAs Detector

>2MHz BandwidthLinear amplifier output 0 to 2.5V

Discontinuity Detection

Event duration: >0.8μs to 1sEvent amplitude: >= 0.5dB

Sampling interval: 0.4μsEvent trace: 750 samples

Data Interface USB 2.0Operating Temperature Range 0ºC to 50ºC (32ºF to 122ºF)Optical Interface Fixed FC (others upon resquest)Power Supply (order country specific) US Standard or Euro Standard

Mechanical Dimensions* Standard 19” rack, 2U(16.8 x 3.8 x 10 inch)

OP

11

00

* For channel counts 1-4 only.For complete specifications visit www.optotest.com

OP750

The OP750 Multichannel Source is available in up to 24 channels, or up to 12 dual-wavelength channels, with a mix of LEDs and/or LASERs. With support for most common connector options, a variety of available wavelengths, adjustable power levels, and a built-in optical switch, the OP750 is ideal for use as a stand-alone source or paired with an optical power meter for insertion loss testing.

The OP750 is entirely customizable to meet customer needs (including but not limited to):

• LED and LASER options include Fabry Perot, DFB, VCSEL

• Available wavelengths include 635, 650, 780, 850, 980, 1310, 1320, 1550, 1625nm

• Added temperature stabilization upon request

• Interfaces include SMA, ST, FC, SC, LC, MTRJ, E2000, 1.6mm,1.25mm, 2.0mm, 2.5mm

Contact your OptoTest sales representative for more information on the available customization options for the OP750.

OP715

The OptoTest OP715 Benchtop LED/LASER Source can be configured up to 4 channels with a mix of LEDs and/or LASERs. Ideal as a compact, stand-alone source or used in conjunction with an optical power meter to measure insertion loss. Factory configurable wavelength mix including LED and LASER.

Stabilized Light Source

Multichannel Source

Light Emitting Diode (LED)Typical Spectrum

center wavelength center wavelength center wavelength

Fabry Perot LaserTypical Spectrum

1310nm, 1490nm, 1550nm, 1625nm LASER 850nm, 1300nm LED

Source Center Wavelength ±30nm from nominal ±30nm from nominalSource Bandwidth <10nm <140nm (850nm) <200nm (1300nm)Internal Fiber 9/125µm (SMF28) 50/125µm, 62.5/125µm, 105/125µmLaunch Condition N/A Available upon request

Output Power (typical) -2.5dBm -18dBm(850nm) -20dBm(1300nm): 62.5/125µm

Source Stability* ±0.02dB ±0.02dB

* Over 1 hour with a max. change of 1ºC. For complete specifications visit www.optotest.com

SO

UR

CE

S

850nm VCSELTypical Spectrum

FWHM

Farfield Scan Range -0.5 NA to +0.5 NA (-0.5rad to +0.5rad)resolution: 2.2 mrad

Nearfield Scan Range 250µm, 0.1µm resolution

Wavelength Range 850nm to 1700nm (InGaAs)450nm to 1100nm (Silicon)

Optical Power Range +20dBm .. -45dBm

Optical Interface Universal 2.5mm, 1.25mm, 1.6mm

Mechanical Dimensions Standard 19” rack, 3U

Analysis SoftwareFarfield scans

Nearfield scansEncircled Flux per IEC

OP

10

21

For complete specifications visit www.optotest.com

OP1021

Encircled Flux The Launch Condition Analyzer characterizes connectors, fiber components, and provides graphs illustrating how light exits the fiber. The analyses ensure conformity to industry standards.

Nearfield Analyzer The Nearfield (NF) describes the optical power density on the surface of a radiating source or the end of a fiber. The nearfield measurement can determine the refractive index profile of multimode fibers and the fiber’s mode filling, launch condition, and Encircled Flux.

Farfield AnalyzerThe Farfield (FF) measurement is the optical power density of a source or fiber end on a surface measured at a radial distance. The farfield measurement can determine the numerical aperture of fibers. In addition, the farfield measurement technique is used to perform a mode field diameter measurement per TIA/EIA-455-191A, a measurement instrumental in the development and qualification of SM fiber.

Launch Condition Analyzer System | Encircled Flux

OP752-MODModal ConditionerWith the OptoTest OP752 Multichannel Modal Conditioner, you can quickly meet critical launch condition requirements like Encircled Flux, M80 or 70/70 fill for multichannel test setups. When used in conjunction with the OptoTest Multichannel LED Sources (OP750 Series) or Return Loss Meters (OP940 Series), launch conditions can be met without the need for external mandrel wraps.

OP-LCKITLaunch Condition KitMeeting critical launch condition requirements is often difficult or overlooked. With the OptoTest Launch Condition Kit, it is easier than ever to meet specifications for many common launch conditions. The OP-LCKIT produces a controlled launch and can be specified for common connector types (FC, SC, LC, etc.) with UPC or APC polish, fiber size (50µm, 62.5µm, etc.), and to meet launch conditions such as Encircled Flux, M80, or 70/70 fill.

Integrating Sphere

High Performance Reference Cables

AdaptersOptoTest’s wide selection of detector adapters make testing most common types of connectors easy and allows for the highest level of accuracy. All of OptoTest’s detectors that are 3mm and smaller come with the Universal Adapter Interface, which accommodates our AD family of detector adapters for most simplex connector types. Detectors that are 5mm and larger utilize the Large Area Detector Interface, which correspondingly accepts our LAAD family of adapters. All adapters are interchangeable within their family to allow for fast and accurate testing of hybrid and fanout cables, and to allow for changes in test setups for different cable types.

The OP-SPHR Integrating Sphere is designed as a cost-effective solution for optical testing of fibers terminated with high-density connectors such as MTP®/MPO or bare fiber. The Integrating Sphere works by reflecting and evenly distributing the light over the entire surface of the internal cavity, making Insertion Loss (IL) measurements stable and repeatable with low polarization dependence.

The screw-on design is ideal for implementing into new or existing Test Systems to accommodate up to 72 fibers, and can be used with all OptoTest 1mm and 3mm detector designs.

www.optotest.comOptoTest® is a registered trademark of OptoTest Corporation of California.

© 2018 OptoTest Corporation. All rights reserved.

1.805.987.1700sales@optotest.com

engineering@optotest.comR&D_CATALOG Rev. A

OptoTest Corp.4750 Calle QuetzalCamarillo, CA 93012 USA

HPR

AD-SPHR-25 AD-SPHR-SC AD-SPHR-BFA

HPR-MTP

AD-25AD-FCAD-125

AD-ST

LAAD-MTP

AD-LC AD-E2

LAAD-MT LAAD-FC