OOptina spojka / Fiber Optic Closure Optiptina spojka / Fiber Optic ?na spojka / Fiber Optic...

Click here to load reader

download OOptina spojka / Fiber Optic Closure Optiptina spojka / Fiber Optic ?na spojka / Fiber Optic ClosureOptiptina spojka / Fiber Optic Closurena spojka / Fiber Optic Closure

of 7

  • date post

    07-May-2018
  • Category

    Documents

  • view

    226
  • download

    5

Embed Size (px)

Transcript of OOptina spojka / Fiber Optic Closure Optiptina spojka / Fiber Optic ?na spojka / Fiber Optic...

  • OptiOptiOptiOptina spojka / Fiber Optic Closurena spojka / Fiber Optic Closurena spojka / Fiber Optic Closurena spojka / Fiber Optic Closure 015Y1015Y1015Y1015Y1

    Data sheet with assembly tips

    Predstavitev Optine spojke uporabljamo za trajno spajanje vlaken in za odcepljanje vlaken ali kablov. Spoji so shranjeni v tesnjenem plastinem ohiju. Spojka Fiber+ je zasnovana modularno. Sprejme lahko do 9 velikih kaset oziroma do 216 zvarov. Vsaka kaseta ima vgrajeni 2 drali za 12 oziroma najve 24 itnikov zvara. Spojka je primerna za navpino ali vodoravno uporabo, za montao na drogove, na jeklene vrvi ali v jake. Takoj po vhodu kablov v spojko so nameene posebne spone iz Inox-a za pritrditev kevlarja ali razbremenilnih elementov. Spojka ima 4 okrogle vhode za kable premera 8-21mm, en okrogli vhod za kable 8-15mm in en ovalni vhod za 2 ne-odrezana kabla premera najve 25mm. Na voljo so razlini dodatki in oprema.

    Introduction Fiber optic enclosures are used for permanent connecting and branching of fibers and fiber optic cables and are suitable for direct underground laying and outdoor installation. The special design provides for quick and easy installation. Consequently, trouble-free operation is guaranteed for several decades even for outdoor installations. The enclosure has separate strain relief points for central strength member and Kevlar reinforcement, 4 round entries for cables 8-21mm, one round entrie for cables 8-15mm and one oval entry for 2 uncut cables up to 25mm. With capacity up to 216 splices the Fiber+ splice enclosure is ideal for aerial and underground FTTx applications.

    1

  • Features

    for aerial and underground applications

    innovative modular design complete scope of supply, ready for splicing easy fiber management for looping through resp. uncut fibers enough space for surplus fibers re-opening and sealing without special tools suitable for uncut cables cost effective rugged and compact design Monosti / Configuration

    tevilo kaset number of trays

    12 zvarov na kaseto 12 splices per cassette

    24 zvarov na kaseto 24 splices per cassette

    1 12 24 e vgrajeno v spojko / Scope of Supply 2 24 48

    3 36 72 4 48 96 5 60 120 6 72 144 7 84 168 8 96 192 9 108 216

    Cable and Port Preparation Prepare the cable according to the picture. Mark the cutting point on the cable at the length 1800mm. Remove the sheath of the cables from the marked point by stripper.

    Unlock the plastic hoop and separate the base and the body of the closure. Open required ports with suitable tool. Insert the prepared cable into heatshrink. Enter the cables into the opened ports of the closure.

    2

    an additional 35mm hole made through the plastic frame for easier access from one side to another

  • Cable retention Fix the cables in to the base using cable clamps. Put the reinforcment or central strength member into the whole of the Inox bolt. Pull the reinforcment toward closure base plate and tighten the screw. Cut the protruding reinforcment approx. 10mm near the bolt.

    Mounting Shrink Tube Move heatshrink tube over and the cable into the port. For heat protection put foil over the adjacent ports. Hold the cable and the heatshrink in the right position an heat the heatshrink with a fan preferably even over the length and the perimeter. Do not heat too long over the port, because the heatshrink can move toward the cable. Stop heating if the glue leaks out of the heatshrink tube. Shrink all used ports.

    3

  • Feeding Loose Tubes

    Use protective tube to enter grouped fibers into the splice tray, or use loose tubes of the cable as shown belove. Put the loose tubes entering from the bottom port with one loop. Put one loose tube into the cassette according to the picture, fix it with cable ties and feed the fibers in the inner channels.

    The sheet of splice tray can be used for the loose tubes protecting and grouping. Also surplus tubes/fibers can be wreathed or branched inside the sheet of splice tray.

    Installation of Fibers Stripped fibers are now operated inside the splice tray. The splice tray/cassette has integrated 2 splice holders, each splice holder module can accept up to 12 standard splice protectors 40 mm long, up to 6 splice protectors in each layer. After fiber splicing operation, please put the splice cassette cover onto the splice tray for protecting fibers.

    4

  • Final steps Fix a drier at the splice tray holder by adhesive tape to keep the inside of the closure dry. Mount the rubber sealing ring to the base of the closure. Keep rubber sealing ring clean. Put the cover to the base of the closure and lock the plastic hoop.

    Fixing of the closure Use enclosed metal hoops for fixing the closure.

    5

  • Vsebina dobave (015Y1)

    Scope of supply (015Y1)

    Ohije s pokrovom in veznim obroem, tesnilna guma, montani okvir, 2 kaseti, pokrov za kasete, suilo, 4 toplo skrne cevi za kable od 8 do 21mm, 1 toplo skrna cev za ovalni vhod, zaitne cevke za vlakna, klinasti vloek za ovalni vhod, dva kovinska obroa za montao na steno ali drog, nalepke za oznaevanje, vezice, zaitna folija, brusni papir in trak z jei. Dodatne kasete od 1 do 7 (015Y2) z vgrajenimi drali za itnike zvara se naroa posebej.

    Base enclosure with locking ring, Sealing ring, Cassette support, 2 Splice Cassettes, Cassette cover, Drying agent, 4 heat shrink tubes for cable 8-21mm, 1 heat shrink tube for oval cable entry port, Fiber Protective Tubes, Branch clip, Metal hoop for mounting at poles or walls, Label paper, Cable fix ties, Tinfoil papers, Sand papers, and Splice trays Fixed band. Up to 7 additional splice cassettes with integrated splice holders must be ordered separately.

    Branch clip Protective tube Rubber sealing ring

    Heat shrink tube Drier Metal hoop

    Label paper Cable ties Tinfoil paper

    Sand paper Splice tray fixed band Port configuration

    Cable entry

    Qty Inner (mm)

    Length (mm)

    Suitable

    cable mm)

    R1 1 16 60 8-15 R2 4 22 60 8-21 OV 1 63 x 28 60 2 x (8-25)

    6

  • Technical data Dimensions (DxL) 150 x 540mm Materials closure body thermoplastic PP; metal hoop steel; splice cassettes and

    fiber management thermoplastic ABS/PC flame-retardant; strain relief points Inox; sealing ring rubber

    Weight Approx. 3 kg Colours closure body black (RAL 9005); metal hoop galvanised steel; splice

    cassettes and fiber management signal white (RAL 1003) Bending radius limitation 35mm for fibers Installation temp. range -5 up to +45C Operating temp. range -40 up to +60C Atmospheric Pressure 70kPa~106kPa Protection class IP 68 Mechanical strength Load (1 min) 2000 N/m2 at centre of the enclosure Impact (3 times) 16 N.m Tight from -40C to +65C Tightness with cable Strain (15 min) 800 N Shearing/bending (10 times) Deflection 45 or a max. of 150 N bending force Torsion (10 times) 90 rotation angle or a max. torque of 50 Nm, Temperature changes -40C to +65C, 10 times Podatki za naroilo / Ordering information

    Koda / Item Ime izdelka / Description

    015Y1 kabelska spojka s priborom, vgrajeni 2 kaseti / splice closure with 2 cassettes and accessories

    015Y2 dodatna kaseta za 12-24 zvarov / additional splice cassette for 12-24 splice protectors

    7