SARLON SPARKLING ACOUSTIC VINYL_. INTRODUCTION_ BENEFITS_ SUGGESTED SPECIFICATION_ INSTALLATION...

SARLON SPARKLINGACOUSTIC VINYL_

INTRODUCTION_

BENEFITS_

SUGGESTED SPECIFICATION_

INSTALLATION INSTRUCTIONS_

MAINTENANCE PROCEDURES_

TECHNICAL PROPERTIES_

Sarlon Sparkling Acoustic VinylSarlon Sparkling is the answer to many constraints and requirements in the health sector. Sarlon Sparkling is a 15dB acoustic compact PVC floor covering that combines acoustic efficiency with excellent indentation resistance.

INTRODUCTION_

Sarlon Sparkling is the answer to many constraints and requirements in the health sector

Sarlon Sparkling is a 15dB acoustic compact PVC floor covering that combines acoustic efficiency with excellent indentation resistance

The density of the product provides a unique resistance to heavy loads and facilitates easy rolling of indoor wheeled traffic

Sarlon Sparkling benefits from a new antibacterial and antifungal treatment based on silver ions called BACTERI’PROTECT, which allows for the elimination of 99% of bacteria after 24 hours and fights effectively against micro-organisms in sensitive places, such as hospital environments, throughout the service life of the product

Sarlon Sparkling has a group T abrasion resistant mineral-embossed PVC wear layer that is exceptionally scratch resistant

The STAIN’PROTECT surface coating provides proven resistance to stains generated by hospital products like Betadine, Eosin, Dakin, fluorescein, Hibiscrub and hydroalcoholic gels

It is also effective against chemical products such as ammonia, white spirit, acetone and domestic products like bleach. These exclusive treatments facilitate easy cleaning and exceptional hygiene standards


BENEFITS_

15dB impact sound reduction

Maximum 0.06mm residual indentation

R10 slip resistance

Improved durability

Resistant to stains

Resistance to heavy loads

Permanent and controlled antibacterial and antifungal treatment

Prevents development of germs and bacteria from the sub-floor

Facilitates indoor wheeled traffic


SUGGESTED SPECIFICATION_SHEETING

Supply and fix 2.6mm thick x 2.0m wide Sarlon Sparkling 15dB acoustic heterogeneous vinyl sheeting with STAIN’PROTECT surface treatment, manufactured in accordance with EN 651 and laid in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste

The sheeting must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive

Joins must be butted, grooved and heat welded using FloorworX Welding Rod, ensuring that the welding rod bonds to more than 70% of the sheet thickness


WARRANTY_

FloorworX offers a 5 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations


INSTALLATION INSTRUCTIONS_

Sarlon Sparkling should be installed in accordance with manufacturer’s recommendations

Training Centre is available for installation training to installers

SUB-FLOOR_

Sub-floors must be smooth, hard, clean, and dry before laying commences

The final appearance and durability of any resilient flooring installation depends largely on the condition of the surface upon which it is laid

A good sub-floor is vital in achieving a satisfactory adhesive bond and long-term durability

Uneven, solid or suspended timber floors may need preparation to meet the required standard


SUB-FLOOR_

All sub-floors must be tested for moisture content prior to installation

To prevent problems associated with rising damp - it is essential that a damp-proof membrane be incorporated beneath the sub-floor

The South African Standard Building Regulations require that all sub-floors in contact with the ground are so constructed as to be damp-proof

Water is an integral part of the construction of a sub-floor - the amount of water used depends on the type of sub-floor, the required structural strength and the extent of curing

It is impossible to state a time period after which a sub-floor may be considered dry enough upon which to lay flooring - factors such as ambient temperature, relative humidity, thickness of the slab, type of finish required and methods used to cure the concrete, will affect this period

There are various methods of testing the moisture content within the sub-floor, which includes the use of a Hygrometer – the most practical and accurate instrument


CLIMATIZATION_

Sarlon Sparkling must be allowed to relax for 24 hours in a uniform room temperature between 18°C and 27°C prior to installation

ADHESIVE_

The recommended adhesive for Sarlon Sparkling is FloorworX No. 62 acrylic adhesive

Adhesive to be spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre

POST INSTALLATION_

It is essential that during the course of installation the material be rolled in both directions with an articulated 68kg three section metal floor roller


MAINTENANCE_PREVENTIVE CARE

Approximately 80% of the dirt and soiling that has to be cleaned off a floor has been trafficked in from outside the building. More than 90% of that soiling can be avoided by the use of an effective entrance matting system

When less dirt is trafficked through the entrance there will be a reduction in maintenance requirements.

Regular cleaning is more cost-effective and hygienic than occasional heavy duty cleaning

Wipe up any grease and oil spills immediately and treat stains as soon as they are observed

Black rubber wheels and rubber furniture feet can discolour the floorcovering - hard plastic is preferred

Always follow the manufacturer’s dosage instructions regarding the use of cleaning chemicals


MAINTENANCE_POST INSTALLATION SITE CLEAN

Floor maintenance begins immediately after the completion of installation

The initial step is to remove any loose dirt or debris using a dry mop, broom or vacuum

Sand, construction debris and sharp-edged objects may result in irreparable damage being inflicted to the new floor.

Remove any visible adhesive residue using a damp cloth, once the adhesive has cured it will be difficult to remove

If other trades are working in the building after the installation of the flooring, the floor must be protected from subsequent damage by the use of thick paper, cardboard or hard board.

No wet maintenance must take place until 72 hours (3 days) have elapsed from the time of installation - this is to ensure that the adhesive has sufficient time to cure properly and develop full bond strength


MAINTENANCE_INITIAL CLEAN

Dust mop or vacuum the floor to remove loose soil and dust

Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with clean water, with a rotary machine fitted with a blue pad

Remove the residue immediately after scrubbing using a wet/dry vacuum

Rinse with clean water using a flat mop and allow the floor to dry

Dry buff the floor using a rotary or high speed machine fitted with a white pad

For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry

FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss


MAINTENANCE_REGULAR CLEANING

Dust mop with flat mop or vacuum on a daily basis to remove dust and loose dirt

Treat spills, spots and stains immediately

Spot clean by hand with a red or white pad and a diluted solution of FloorworX Maintain, working from the outside of the mark to its centre

Dry buff or spray buff periodically, as described in 4.1 Initial Clean above

The frequency of dry buffing or spray buffing is dependent on the amount of foot traffic and the effectiveness of the daily cleaning regime


MAINTENANCE_PERIODIC MAINTENANCE

Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with clean water, with a rotary machine fitted with a blue pad

Remove the residue immediately after scrubbing using a wet/dry vacuum

Rinse with clean water using a flat mop and allow the floor to dry

Dry buff the floor using a rotary or high speed machine fitted with a white pad

For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry

FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss


TECHNICAL PROPERTIES_


Please feel free to visit our newly revamped website at www.floorworx.co.za

Read our Blog on our website at http://www.floorworx.co.za/category/blog/

Subscribe to our Newsletter by mailing your request to [email protected]

Follow us on Facebook, Twitter, YouTube & Pinterest

END OF PRESENTATION_

http://www.floorworx.co.za/

http://www.floorworx.co.za/category/blog/

http://www.floorworx.co.za/category/blog/

mailto:[email protected]

SARLON SPARKLING ACOUSTIC VINYL_. INTRODUCTION_ BENEFITS_ SUGGESTED SPECIFICATION_ INSTALLATION...

Documents

Transcript of SARLON SPARKLING ACOUSTIC VINYL_. INTRODUCTION_ BENEFITS_ SUGGESTED SPECIFICATION_ INSTALLATION...