FLOTEX FLOCKED FLOORING_. INTRODUCTION_ BENEFITS_ RANGES_ SUGGESTED SPECIFICATION_ INSTALLATION...

FLOTEXFLOCKED FLOORING_

INTRODUCTION_

BENEFITS_

RANGES_

SUGGESTED SPECIFICATION_

INSTALLATION INSTRUCTIONS_

MAINTENANCE PROCEDURES_

TECHNICAL PROPERTIES_

Flotex Flocked FlooringFlotex Flocked Flooring is a completely unique textile flooring that combines the hard wearing and durable characteristics of a resilient floor with the quality, warmth and comfort of a carpet

INTRODUCTION_

Flotex Flocked Flooring is a completely unique textile flooring that combines the hard wearing and durable characteristics of a resilient floor with the quality, warmth and comfort of a carpet

Flotex consits of a solid vinyl reinforced base layer into which a densely flocked surface of nylon 6.6. fibres are firmly anchored

Flotex is extremely dimensionally stable and has the optics of a textile floor covering, whilst being as functional and durable (as well as easy to clean) as any resilient floor covering. Flotex is available in both sheet and tile format

Flotex is a choice, not a compromise

The anti-microbial sanitized® treatment on Flotex ensures consistent protection against bacteria without degeneration through cleaning or vacuuming

It also suppresses the growth of dust mite populations therefore Flotex has a positive impact on the lives of allergy sufferers even more as daily vacuuming cleans away twice as many allergens compared to conventional carpets. Which has awarded Flotex the British Allergy Foundation seal of approval


BENEFITS_

Flotex provides up to 20dB impact sound reduction

Impervious backing suitable for wet cleaning

Flotex is slip resistant both when wet and dry

Over 70 million nylon 6.6 fibres per m²

Flotex holds allergens and dust to the floor and releases them when vacuumed

Approved by the British Allergy Foundation

Treated with a Sanitized® antimicrobial which gives protection against mould, bacteria and odours


RANGES_FLOTEX COLOUR

Flotex Calgary (tiles & sheeting)

Flotex Penang (tiles & sheeting)

Flotex Metro (tiles & sheeting)

Flotex Artline (11cm & 22cm wide strips)

RANGES_FLOTEX LINEAR

Flotex Integrity2 (tiles only)

Flotex Complexity (tiles only)

Flotex Stratus (tiles & sheeting)

Flotex Cirrus (tiles & sheeting)

Flotex Pinstripe (tiles & sheeting)


SUGGESTED SPECIFICATION_TILES

Supply and fix 4.3mm thick x 2.0m wide Flotex electrostatically flocked textile sheeting or 5.3mm thick x 500mm x 500mm Flotex electrostatically flocked textile tiles, manufactured in accordance with EN 1307 and laid, in accordance with manufacturer’s instructions, in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste

The flooring must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive

Joins must be tightly butted.


SUGGESTED SPECIFICATION_SHEETING

Supply and fix 4.3mm thick x 2.0m wide Flotex electrostatically flocked textile sheeting or 5.3mm thick x 500mm x 500mm Flotex electrostatically flocked textile tiles, manufactured in accordance with EN 1307 and laid, in accordance with manufacturer’s instructions, in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste

The flooring must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive

Joins must be tightly butted


WARRANTY_

FloorworX offers a 10 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations


INSTALLATION INSTRUCTIONS_

Flotex should be installed in accordance with manufacturer’s recommendations

Training Centre is available for installation training to installers

SUB-FLOOR_

Sub-floors must be smooth, hard, clean, and dry before laying commences

The final appearance and durability of any resilient flooring installation depends largely on the condition of the surface upon which it is laid

A good sub-floor is vital in achieving a satisfactory adhesive bond and long-term durability

Uneven, solid or suspended timber floors may need preparation to meet the required standard


SUB-FLOOR_

All sub-floors must be tested for moisture content prior to installation

To prevent problems associated with rising damp - it is essential that a damp-proof membrane be incorporated beneath the sub-floor

The South African Standard Building Regulations require that all sub-floors in contact with the ground are so constructed as to be damp-proof

Water is an integral part of the construction of a sub-floor - the amount of water used depends on the type of sub-floor, the required structural strength and the extent of curing

It is impossible to state a time period after which a sub-floor may be considered dry enough upon which to lay flooring - factors such as ambient temperature, relative humidity, thickness of the slab, type of finish required and methods used to cure the concrete, will affect this period

There are various methods of testing the moisture content within the sub-floor, which includes the use of a Hygrometer – the most practical and accurate instrument


CLIMATIZATION_

Flotex must be allowed to relax for 24 hours in a uniform room temperature between 18°C and 27°C prior to installation

ADHESIVE_

The recommended adhesive for Flotex is FloorworX No. 62 acrylic adhesive

Adhesive to be spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre

POST INSTALLATION_

It is essential that during the course of installation the material be rolled in both directions with an articulated 68kg three section metal floor roller


MAINTENANCE_PREVENTIVE CARE

Approximately 80% of the dirt and soiling that has to be cleaned off a floor has been trafficked in from outside the building. More than 90% of that soiling can be avoided by the use of an effective entrance matting system

When less dirt is trafficked through the entrance there will be a reduction in maintenance requirements.

Regular cleaning is more cost-effective and hygienic than occasional heavy duty cleaning

Wipe up any grease and oil spills immediately and treat stains as soon as they are observed

Black rubber wheels and rubber furniture feet can discolour the floorcovering - hard plastic is preferred

Always follow the manufacturer’s dosage instructions regarding the use of cleaning chemicals


MAINTENANCE_POST INSTALLATION SITE CLEAN

Floor maintenance begins immediately after the completion of installation

The initial step is to remove any loose dirt or debris using a dry mop, broom or vacuum

Sand, construction debris and sharp-edged objects may result in irreparable damage being inflicted to the new floor.

Remove any visible adhesive residue using a damp cloth, once the adhesive has cured it will be difficult to remove

If other trades are working in the building after the installation of the flooring, the floor must be protected from subsequent damage by the use of thick paper, cardboard or hard board.

No wet maintenance must take place until 72 hours (3 days) have elapsed from the time of installation - this is to ensure that the adhesive has sufficient time to cure properly and develop full bond strength


MAINTENANCE_INITIAL CLEAN

Vacuum the floor using an upright vacuum cleaner fitted with a powered brush

Remove stains or spills using clean warm water, in conjunction with a diluted neutral carpet detergent if required, working from the outside of the stain or spill inwards

When a detergent is used, ensure that the area is rinsed thoroughly with clean water to remove any residual detergent

Remove excess water using a wet/dry vacuum

Allow the floor to dry before permitting foot traffic


MAINTENANCE_REGULAR CLEANING

Vacuum the floor daily using an upright vacuum cleaner fitted with a powered brush

Wet clean using a hot water/spray extraction carpet cleaning machine

Rinse thoroughly with clean water to remove any residual detergent



Remove spills and stains as soon as they occur


MAINTENANCE_OCCASIONAL MAINTENANCE

Soak stains by spraying with a solution of mild detergent

Scrub using a hot water/spray extraction carpet cleaning machine

Rinse thoroughly with clean water to remove any residual detergent




TECHNICAL PROPERTIES_


Please feel free to visit our newly revamped website at www.floorworx.co.za

Read our Blog on our website at http://www.floorworx.co.za/category/blog/

Subscribe to our Newsletter by mailing your request to [email protected]

Follow us on Facebook, Twitter, YouTube & Pinterest

END OF PRESENTATION_

http://www.floorworx.co.za/

http://www.floorworx.co.za/category/blog/

http://www.floorworx.co.za/category/blog/

mailto:[email protected]

FLOTEX FLOCKED FLOORING_. INTRODUCTION_ BENEFITS_ RANGES_ SUGGESTED SPECIFICATION_ INSTALLATION...

Documents

Transcript of FLOTEX FLOCKED FLOORING_. INTRODUCTION_ BENEFITS_ RANGES_ SUGGESTED SPECIFICATION_ INSTALLATION...