PN ERGO Series Balancer File created on Technical ...baffco.com/download/material_handeling/PN...
-
Upload
duongduong -
Category
Documents
-
view
217 -
download
0
Transcript of PN ERGO Series Balancer File created on Technical ...baffco.com/download/material_handeling/PN...
File created on 13/06/2007
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PN ERGO Series Balancer Technical Specifications
GENERAL Update 17/10/2007
CAT500I.doc Page 1 of 2 contr. zo Due to the continuous improvement of the products, these specifications may change without notice.
This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PN Balancer column mounted
General Technical Specifications
� Air pressure 6.5 bars � Noise level < 70 Db � Lift speed from 15 to 30 m/min � Main column axis brake � Intermediate joint axis brake � Continuous column rotation � Slow descent in case of pressure failure
Available options (see specific technical sheets ) � Rotating joint on the articulate axis � System lock for the lift capacity � Brake for up/down movement � Special painting � Steel platform � Limit switch for the main and intermediate
joint axis
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6.5 bars . ** Within certain limits, these values can by modified for special client requirements. *** Values including the relevant safety factor, as per CNR 10021/85 (Steel structures for lifting equipment) ****With counterweights and reinforcement for arm. The load capacity increase over the nominal load
capacity can be used only to counterbalance the weight of the tooling
Technical Specifications - Column mounted Model PN 80 PN 160 PN 250
SQ * (Max Load capacity) Kg 80 110**** 160 210**** 250 310**** Max protrusion from tool axis mm 300 - 300 - 500 -
Min Load Capacity kg 10 10 12 12 15 15 L1 mm 1620 1620 1635 1635 1565 1565 L2 mm 1080 1080 1065 1065 1040 1040 R1 mm 2700 2700 2700 2700 2605 2605 R2 mm 907 907 935 935 900 900 RH mm -- 715 -- 910 -- 960 A ** mm 4174 4261 4243 4327 4011 4118 B ** mm 3300.5 3300.5 3444 3444 3346.5 3346.5 C ** mm 2410 2410 2470 2470 2300 2300
D vertical stroke mm 1752 1752 1716 1716 1451 1451 E ** mm 2007 2007 2012 2012 2002 2002
Weight Kg 358 476 556 711 604 769 Fv max *** daN 544 742 880 1150 1110 1410
Mges max *** daNM 520 450 957 990 1410 1360
File created on 13/06/2007
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PN ERGO Series Balancer Technical Specifications
GENERAL Update 17/10/2007
CAT500I.doc Page 2 of 2 contr. zo Due to the continuous improvement of the products, these specifications may change without notice.
This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PN Balancer Ceiling / rail mounted
General Technical Specifications
• Air pressure 6.5 bars • Noise level < 70 Db • Lift speed from 15 to 30 m/min • Main column axis brake • Intermediate joint axis brake • Continuous column rotation • Slow descent in case of pressure failure
Available options (see specific technical sheets) • Rotating joint on the articulate axis • System lock for the lift capacity • Brake for up/down movement • Special painting • Sliding trolley • Limit switch for the main and intermediate
joint axis
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6.5 bars . ** Within certain limits, these values can by modified for special client requirements. *** Values including the relevant safety factor, as per CNR 10021/85 (Steel structures for lifting equipment) ****With counterweights and reinforcement for arm. The load capacity increase over the nominal load
capacity can be used only to counterbalance the weight of the tooling
Technical Specifications - Column mounted Model PN 80 PN 160 PN 250
SQ * (Max Load capacity) Kg 80 110* 160 210* 250 310* Max protrusion from tool axis mm 300 - 300 - 500 -
Min. Load Capacity kg 10 10 12 12 15 15 L1 mm 1620 1620 1635 1635 1565 1565 L2 mm 1080 1080 1065 1065 1040 1040 R1 mm 2700 2700 2700 2700 2605 2605 R2 mm 907 907 935 935 900 900 RH mm -- 715 -- 910 -- 960 A ** mm 4293 4293 4388 4388 4172 4172 B ** mm 1602.5 1602.5 1614 1614 1536.5 1536.5 C ** mm 690 690 610 610 480 480
D vertical stroke mm 1752 1752 1716 1716 1451 1451 E ** mm 2007 2007 2012 2012 2002 2002
Weight Kg 290 408 465 620 548 713 Fv max *** daN 466 663 780 1050 1010 1300
Mges max *** daNM 520 450 957 990 1410 1360
File created on 17/04/2002
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PN COMPATTO Series Balancer
Technical Specifications GENERAL
Update 01/12/2005
CAT501D.doc Page 1 of 2 contr. fa Due to the continuous improvement of the products, these specifications may change without notice.
This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PN COMPATTO Balancer Ceiling mounted
Technical Specifications - Ceiling mounted Model XC080 XC100
SQ * (Load capacity) Kg 80 100 L1 mm 1290 1190 L2 mm 910 910 R1 mm 2200 2100 R2 mm 640 540 A mm 3485 3419
B ** mm 965 965 C ** mm 230 230
D Vertical stroke mm 1088 686 E ** mm 1998 1998
Weight Kg 198 196 Fv max *** daN 273 291
Mges max *** daNM 316 350
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6 bars . ** Within certain limits, these values can by modified for special client requirements. *** Values including the relevant safety factor, as per CNR 10021/85 (Steel structures for lifting equipment)
General Technical Specifications • Air pressure 6 bars • Noise level < 70 Db • Lift speed 30 m/mn • Main column axis brake • Intermediate joint axis brake • Continuous column rotation • Slow descent in case of pressure failure
Available options (see specific technical sheets )
• Rotating joint on the articulate axis • System lock for the lift capacity • Brake for up/down movement • Double braking force on the main and
intermediate axis • Special painting • Sliding trolley
File created on 17/04/2002
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PN COMPATTO Series Balancer
Technical Specifications GENERAL
Update 01/12/2005
CAT501D.doc Page 2 of 2 contr. fa Due to the continuous improvement of the products, these specifications may change without notice.
This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PN COMPATTO Balancer Rail mounted
Technical Specifications - Rail mounted Model XC080 XC100
SQ * (Load capacity) Kg 80 100 L1 mm 1290 1190 L2 mm 910 910 R1 mm 2200 2100 R2 mm 640 540 A mm 3480 3205
B ** mm 960 751 C ** mm - -
D Vertical stroke mm 1088 686 E mm 1998 1998
Weight Kg 283 291 Fv max *** daN 356 398
Mges max *** daNM 316 350
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6 bars . ** Within certain limits, these values can by modified for special client requirements. *** Values including the relevant safety factor, as per CNR 10021/85 (Steel structures for lifting equipment)
General Technical Specifications • Air pressure 6 bars • Noise level < 70 Db • Lift speed 30 m/mn • Main column axis brake • Intermediate joint axis brake • Continuous column rotation • Slow descent in case of pressure failure
Available options (see specific technical sheets )
• Rotating joint on the articulate axis • System lock for the lift capacity • Brake for up/down movement • Double braking force on the main and
intermediate axis • Special painting
File created on 23/01/2002
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PNF Series Balancer Technical Specifications
GENERAL
Update 01/12/2005
CAT400B Page 1 of 1 contr: fa Due to the continuous improvement of the products, these specifications may change without notice. This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PNF Balancer Description: Rope Pneumatic load balancer with orbit-arm, column mounted
Technical Specifications Model PNF250 PNF300 PNF350
SQ * (Load capacity) Kg 80 80 80 L1 mm 1250 1500 1750 L2 mm 1250 1500 1750 R1 mm 2500 3000 3500 R2 mm 650 750 1110 A ** mm 3003 3003 3108 C ** mm 2800 2800 2800
D vertical stroke mm 1700 1700 1700 Weight Kg 200 206 226
Fv max *** daN 356 364 387 Mges max *** daNm 418 502 617
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6 bars . ** Within certain limits, these values can by modified for special client requirements. *** Values including the relevant safety factor, as per CNR 10021/85 (Steel structures for lifting
equipment)
General Technical Specifications • Air pressure 6 bars • Noise level < 70 Db • Lift speed 45 m/mn • Main joint axis friction • Intermediate joint axis friction • Slow descent in case of pressure failure
Available options (see specific technical sheets ) • Special painting • Steel platform
File created on 29/01/2003
SCAGLIA INDEVA S.p.A. italy [email protected] www.indevagroup.com
PNZ Series Balancer Technical Specifications
GENERAL
Update 01/12/2005
CAT300B Page 1 of 1 contr: fa Due to the continuous improvement of the products, these specifications may change without notice. This document is the property of Scaglia S.p.A. Any partial or full reproduction without written authorization by the owner is prohibited.
PNZ ZIP Balancer Description: Pneumatic load balancer with arm, Rail mounted
Technical Specifications Model PNZ080 PNZ050
SQ * (Load capacity) Kg 80 50 A mm 3100 3100 B mm 650 650 C mm 515 385
D vertical stroke mm 600 800 E mm 2145 2045 F mm 325 225
Weight Kg 40 45 L mm 600 800
* Nominal load capacity SQ is determined with a compressed air supply of minimum 6 bars .
General Technical Specifications • Air pressure 6 bars • Noise level < 70 Db • Lift speed 50 m/mn • Slow descent in case of pressure failure
Available options (see specific technical sheets )
• Special painting