New GM MDI Multiple Diagnostic Interface with

WIFI

GM MDI is a new GM Diagnostic tool.

It does not only work for the new gm car,but also for the old kind of car.It can

test Chinese and American GM cars from 1990-2012.

GM Multiple Diagnostic Interface (MDI) Programming Solution Bundle!

Language:

Multiple Diagnostic Interface Descripition:

for General Motors Global Electrical Architecture (Global A) and Global

Diagnostic Hardware &Software

Global Diagnostic System DGS&Mutiple diagnostic Interface MDI

MDI and GDS Background

MDI is an interface between the vehicle DLC and a PC (by wired USB, wired

Ethernet, wireless Ethernet ) and TIS2web.

Can be Used for SPS programming on existing and future SGM vehicles

Required for diagnostics on new SGM Global A Electrical Architecture

Vehicles

Used with TIS2Web, GM Global Diagnostics System (GDS), SPS and MDI

Manager Software

Allows for GDS diagnostic

GM Multiple Diagnostic Interface (MDI)

All current and most legacy vehicle protocols: UART, KW2000, CLASS2, GM

LAN, etc.

Needed for Global A architechture vehicles

Supports Service Programming System (SPS)

Pass through progrmming on past model and Global A vehicles

Supports PC-Based diagnostics with rollout of the Global Diagnostic System

(GDS) application

Includes Flight Recorder Mode

New Diagnostic Application Software required for Global A Vehicles

Global Diagnostic System (GDS)

PC-based software diagnsotics

DTCs, Diagnostics, Data Display & Visualization, Device Controls, Special

Tests, Flight Recorder management, etc.

GDS is software which runs on a specific PC. Updates received via TIS2Web.

Multiple display options. More space for diagnsotics. Session management for

multiple us.

Future of the Tech 2

The Tech 2 remains an essential tool through at least the 2010 model year.

The GM MDI will not support past models when its diagnostic capabilities are

introduced. And, the Tech2 will continue to be needed to diagnose all vehicles

fromprevious model years. Remote programming with the Tech 2 will continue

to be supported for use on all 2007 and previous vehicles.Additional

information will be supplied in future.

HOW WILL THE GM MDI BE USED?

The new GM MDI can be used only in the Pass-Thru method. This means you

can use it as your programming tool, while your Tech 2/CANDY remains

available for diagnostics and other duties.

The GM MDI is initially being introduced with Pass-Thru programming

capabilities only. It can be used to perform Pass-Thru programming on all

vehicles built since 1996 and will support all vehicles into the future.

The GM MDI will be required to perform diagnostics on selected NAO vehicles

for model year 2009. Diagnostic software is scheduled to be released for the

GM MDI during the fourth quarter of 2008. Regulations require programming

procedures to be compliant with SAE Recommended Practice J2534.

The GM SPS is compliant with SAE Recommended Practice J2534, and the

GM MDI is compliant with the portions of SAE J2534 that are applicable for

GM vehicles.

Multiple Diagnostic Interface Feature:

1. With opel Global tis global diagnostic system

2. Support offline lease function

3. Support for Opel offline programming function

4. With GDS2 diagnostic system

5. Tech2win diagnostic software support adding latest software

6. support programming online

7. support cable communication

8. support wireless communication

9. support original factory latest software

10. With European for Chevrolet Global tis, Supports European for Chevrolet

offline programming

11. All Chip are new and original

Multiple Diagnostic Interface Spported

protocols:

For immediate use — At present, vehicles have two buses on the 16 pin

connector (high speed and low speed GMLAN). The GM MDI

communicates using all of the existing GM protocols, the same as the

Tech 2:

- UART

- Class 2

- KWP2000

- GMLAN (CAN)

Beginning with the 2008 model year vehicles, Pass-Thru will be the only

programming method available. (Remote will continue to be available for

previous vehicles.

when you test after 2010 year gm car ,you can use gm gds2 software:

When you want to test before 2010 year GM car, you can use the techwin

software to test it,run fast and stable:

GM MDI installation

PC specification require: Full installation version WIN XP3, pls install all the

systerm patch (picture 0)

1: Open the software folder, double click “CD for Start”pop-up installation

window,and click “install” ( Picture 1)

2: Pls install the software in order : JAV A.EXE；Validat.exe;GMMDI

Software.exe;Tech2Win.exe; (picture 2-6)

3: automatic install all the files above, when have message “ Copying

PCMCIA files..”,please don’t touch any keyboard or mouse, just leave it alone,

the GM MDI USB drive will automatic install. (Picture 7-10)

4: after installation finish, there will be have a message “ press any key to

continue…” and pls press any key, and software installation partly finish

( Picture 11)

5. Pls connect the USB cable to PC ( do not need to connect to the Car OBD

at this time), the first time connect USB to PC, the USB drive will be detected

on the lower right corner, then choose automatic install, click next to finish.

6. when USB drive installation finish, on your PC device manager ,you will find

a “MDI USB Device(COM...” on Port place. (Picture 12) , if not then pls find

the drive on MDI folder on the CD and install, if still not successful, then pls

check if the PC operation is correct or not.

7. open “GM MDI Menager” on the desk to do connection test (if the USB was

correct installed, the red “X” on the dialogue will disappear, if the red “X” still

on, then pls repeat steap 6

8: finish the installation above, pls connect your PC with internet. ( do not

connect to the car OBD ) open this website and activate lease.

http://tis2web.eicp.net:9080/tis2web/after you open this web. Write any user’s

name and click ok. All choose OK /continue ( picture 15-17)

9: in the main interface, please click “Global Diagnostic System2(GDS 2)” icon,

and click GDS2 to run, at that time, software will update lease automatic .after

update finish, software GDS2 (Launch GDS2 on the desk) will open

automatically , choose the language and back to the main interface.

Bottom left will have a lease expire time. Be attention, it need only your PC

systerm time, don’t change. Afterward we don’t need internet to update lease,

so if there have any remind indicate new update available,please do not click

update (picture 18-21

Test steps:

1: finish update lease step, connect with Car OBD, click diagnostic icon on the

interface. Choose brand and click “input” on lower right corner, car information

will be read automatically, or you can choose manual input VIN

2:choose test what you want, like module diagnostic—engine control

modual—identifying information ( picture22-27)

FAQ:

Q:Can your GM MDI work with wireless?can it be updated?

A:It is with wireless WIFI,can be updated by Email(new version).

Packing List:

1pc x GM MDI Main unit

1pc x OBD2 Cable

1pc x USB Cable

1pc x Lan Cable

1pc x AC Adapter

1pc x Screw (used to fix the usb cable when connecting usb cable with main

unit)

1pc x CD Software

http://www.obdii.co.uk/car-diagnostic-tools-c-2/newest-mdi-multiple-diagnostic-interface-with-wifi