MAE Repor… · James McCabe (PhDAE), Advisor: DeMars, K. J., NASA Space Technology Research...

MAEM E C H A N I C A L A N D A E R O S PA C E E N G I N E E R I N G

2016 ANNUAL SCHOLARLY ACTIVITY REPORT

PROFESSIONAL RECOGNITIONDr. S. N. Balakrishnan, AIAA St. Louis Section, Faculty Award, 2016.

Dr. V. Birman, 2016 ASME International Mechanical Engineering Congress & Exposition, ASME Certificate of Appreciation, 2016.

Dr. A. Crosbie, AIAA, Certificate for 40 years of sustained contributions, 2016.

Dr. L. Duan, U.S. Air Force Research Laboratory, Summer Faculty Fellowship, 2016.

Dr. J. Gao, National Science Foundation, Faculty Early Career Development Award (CAREER), 2016.

Dr. J. Rovey, AIAA Lawrence B. Sperry Young Professional Award, 2016.

Dr. C. Wojnar, U.S. Air Force Research Laboratory, Summer Faculty Fellowship, 2016.

Dr. X. Yang, National Science Foundation, Faculty Early Career Development Award (CAREER), 2016.

Dr. X. Yang, Office of Naval Research, Young Investigator Award, 2016.

PUBLICATION RECOGNITION AND AWARDSChandrashekhara, K., Featured Article, BMI Composite Sandwich Structures, Vol. 52, No. 3, 2016. Hosder, S., Fluid Dynamics Year in Review Highlight, AIAA Aerospace America Magazine, December 2016.

Duan, L., Fluid Dynamics Year in Review Highlight, AIAA Aerospace America Magazine, December 2016.

Luo, J., Gilbert, L., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., SPIE Photonics West 2016, Best Paper Award, San Francisco, CA, February 13 - 18, 2016.

CAMPUS RECOGNITION AND HONORSDean’s Scholar Award

Dr. J. Rovey

Dr. X. Yang

Class of ‘42 Distinguished Teaching Award

Dr. J. Schmidt

2016 Faculty Teaching Award

Dr. J. Nisbett

2016 Research Award

Dr. K. DeMars

2015 - 2016 Outstanding Teaching Award

Dr. K. DeMars

Dr. X. Du

Dr. H. Pernicka

Global Learning 2016 Outstanding Teaching Award

Dr. V. Birman

HONORS AND AWARDS

INTERNATIONAL AND NATIONAL STUDENT HONORS AND AWARDSJames McCabe (PhDAE), Advisor: DeMars, K. J., NASA Space Technology Research Fellowship (NSTRF), September 2016.

Amir Ghazanfari (PhDME), Advisor: Ming Leu, Finalist for Best Student Paper Award, “Freeform Extrusion Fabrication of Advanced Ceramic Components With Embedded Sapphire Optical Fiber Sensors,” ASME 2016 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, Stowe, VT, September 28 - 30, 2016.

CAMPUS STUDENT HONORS AND AWARDSJoshua Heck (MSME), Co-Advisors: U. Koylu and M. Leu, 1st Place, “Natural Flow Structure to Design Polymer Electrolyte Membrane Fuel Cell Flow Fields,” Missouri S&T Three Minute Thesis (3MT®) Competition, Rolla, MO, October 6, 2016.

Michelle Gegel (PhDME), Co-Advisors: R. G. Landers and D. Bristow, 2nd Place, “Feedback Control for Additive Manufacturing,” Missouri S&T Three Minute Thesis (3MT®) Competition, Rolla, MO, October 6, 2016.

Tim Victor (BSME), “Optimization of Piezoelectric Cantilever-Based Windmill,” 2nd Place for 12th Undergraduate Research Conference poster presentation, Missouri University of Science and Technology, Rolla, MO, April 11, 2016.

Wei Li (PhDME), “Investigation of Pre-mixed Multi-powder Flow in Fabricating Functional Graded Materials by Blown Powder Deposition,” 3rd Place for 12th Annual Intelligent Systems Center poster presentation, Missouri University of Science and Technology, Rolla, MO, November 16, 2016.

Michelle Gegel (PhDME), Co-Advisors: R. G. Landers and D. Bristow, Chancellor’s Distinguished Fellowship, Fall 2016.

Zachary Gill (PhDAE), Advisor: J. Rovey, Chancellor’s Distinguished Fellowship, Fall 2016.

Robert Meinders (PhDAE), Advisor: K. Chandrashekhara, Chancellor’s Distinguished Fellowship, Fall 2016.

Leah Mason (PhDME), Advisor: M. Leu, Chancellor’s Distinguished Fellowship, Fall 2016.

STUDENT HONORS AND AWARDS

1 2016 ANNUAL SCHOLARLY ACTIVITY REPORT

IN THIS ISSUE1 Honors and Awards

Select honors and awards for faculty and students

2 Department Seminar SeriesIndustry experts and academic scholars present seminars to our students and faculty each year

3 New FacultyDr. Yun Seong Song joins the MAE department

3 Facts and FiguresDepartment statistics regarding research funding, enrollment growth trends and degrees awarded

5 MAE by the NumbersDepartment statistics for CY2016

6 Junior Faculty receive NSF CAREER Awards

7 Faculty

11 New Grants and Contracts

14 Other Active Grants and Contracts

17 Professional and Scholarly Activities

Each semester the mechanical and aerospace engineering department organizes seminars under the sponsorship of the Graduate Seminar Series and the Missouri S&T Academy of Mechanical and Aerospace Engineers (AMAE). One of the purposes of the seminar series is to broaden our students academically and to aid in their professional development by providing another connection with the world of industry, business and research. In recognition of the department’s centennial, established and renowned alumni were also added to the line up. These seminars consist of exceptional speakers whose research spans the range of the mechanical and aerospace engineering disciplines. Through these seminars we seek to expose our faculty and graduate students to a scale of topics in areas both related to and complementary of those areas investigated in the department.

2016 Spring Semester

January 28, 2016 - Dr. Yiguang Ju, Robert Porter Professor, Princeton University

February 4, 2016 - Dr. Mark Mirotznik, Profes-sor of Electrical and Computer Engineering, The University of Delaware

February 25, 2016 - Mr. Karl T. Edquist, Depu-ty PI, STMD Proplusive Descent Technologies Project, NASA Langley Research Center

March 3, 2016 - Mr. Robert Steinhoff, Engi-neer Fellow, Honeywell Federal Manufactur-ing & Technologies, LLC

April 14, 2016 - Dr. Xin Ning, Postdoctoral Fellow, Materials Science and Engineering, University of Illinois Urbana-Champaign

April 28, 2016 - Dr. Perry Ballard, United States Air Force

May 5, 2016 - Dr. Jose Camberos, P. E., AFRL - University Relations Manager, Wright-Pat-terson AFB 2016 Fall Semester

September 1, 2016 - Dr. Robert Wagner, Direc-tor of Fuels, Engines and Emissions Research Center, Oak Ridge National Laboratory

September 22, 2016 - Dr. Paulo C. Lozano, Associate Professor of Aeronautics and Astro-nautics, Chair of Graduate Programs, Director of the Space Propulsion Laboratory, Massa-chusetts Institute of Technology

October 12, 2016 - Mr. Wayne Garrett, Manag-ing Director, IW Capital Partners

October 17, 2016 – Dr. James Friend, Profes-sor of Mechanical and Aerospace Engineer-ing, University of California San Diego

November 10, 2016 - Dr. Michael Watson, Avionics Sensors Engineer, NASA Marshall Space Flight Center

December 8, 2016 – Dr. Scott White, Profes-sor of Aerospace Engineering, University of Illinois

DEPARTMENT SEMINARS

2MECHANICAL AND AEROSPACE ENGINEERING

DR. YUN SEONG SONG Dr. Yun Seong Song is an assistant professor in the mechanical and aerospace engineering department at Missouri S&T. His work and research interest include physical human-robot interaction and rehabilitation robotics, particularly in their applications to understanding and assisting human movement. He conducted his postdoctoral research in the Department of Mechanical Engineering at École Polytechnique Fédérale de Lausanne in 2012-13, as well as in the Department of Biomedical Engineering at Georgia Institute of Technology and Emory University in 2014-16. While at Georgia Institute of Technology, Dr. Song was also a lecturer in the Department of Mechanical Engineering. He graduated with a Ph.D. degree in mechanical engineering from Massachusetts Institute of Technology in 2012. He received his B.S. degree in mechanical engineering and B.S.E degree in computer science and engineering from Seoul National University in 2004. He also holds a M.S. degree in mechanical engineering from Carnegie Mellon University. Among his honors, is the Bennett Award for Outstanding Thesis from Carnegie Mellon University, as well as being a two-time recipient of the Samsung Scholarship for graduate studies.

2011 2012 2013 2014 2015 2016

$9

$8

$7

$6

$5

$4

$3

$2

$1

$0

RESEARCH FUNDING (MILLIONS)

RESEARCH EXPENDITURES NEW AWARDS

NSF38%

NASA34%

NEW FACULTY FACTS AND FIGURES

FEDERAL RESEARCH EXPENDITURES

RESEARCH EXPENDITURES$5,706,968

OTHER: 2%

UNIVERSITY OF MISSOURI: 3%

STATE OF MISSOURI: 1%

OFFICE OF NAVAL RESEARCH: 1%

FEDERAL65%

INDUSTRY29%

2016 RESEARCH EXPENDITURES

DEPARTMENT OF ENERGY: 10%

DEPARTMENT OF EDUCATION: 5%

ARMY RESEARCH OFFICE: 1%

AIR FORCE RESEARCH LAB: 6%

AIR FORCE OFFICE OF SCIENTIFIC RESEARCH: 5%


FACTS AND FIGURES

GRADUATE PROGRAM DEGREES AWARDEDCertificate Programs

CAD/CAM and Rapid Product Realization

Composite Materials and Structures

Energy Conversion and Transport

Engineering Mechanics

Manufacturing Automation

Manufacturing Systems

Control Systems

On-Campus

Distance

Mechanical Engineering

Master of Science

Thesis

Non-thesis

Doctor of Philosophy

Manufacturing Engineering Master of Engineering

Master of Science

Aerospace Engineering Master of Science

Thesis

Non-thesis

Doctor of Philosophy

5 15105 1510

On-Campus

Distance

UNDERGRADUATE PROGRAM DEGREES AWARDEDAerospace Engineering

Bachelor of Science

Mechanical EngineeringBachelor of Science

10 7050 60403020 1009080 160150140130120110 170 180 190 200 210 220

20

ENROLLMENT GROWTHUNDERGRADUATE PROGRAM ENROLLMENTTOTAL PH.D. ENROLLMENT


Aerospace Engineering

100

200

300

400

700

500

600

20152012 2013

Aerospace Engineering


2014

800

201620152012 2013

10

20

30

40

50

60

2014

70

80

90

2016

120

110

100

900

FEDERAL RESEARCH EXPENDITURES


OTHER FAST FACTS78 Journal Articles Published

78 Conference Papers Published

$8 M New Research Awards

* Fall 2016 enrollment records

Graduate student enrollment • Aerospace Engineering

• Mechanical Engineering

• Manufacturing Engineering

• Certificates

Thesis - Aerospace Engineering M.S. - Aerospace Engineering Ph.D. - Mechanical Engineering M.S. - Mechanical Engineering Ph.D. - Manufacturing Engineering M.S. Non-Thesis - Aerospace Engineering M.S. - Mechanical Engineering M.S. - Manufacturing Engineering M.E.

Quantitative GRE of graduate students Percentage of supported graduate students GRA/GTA ratio based on FTE M.S. degrees (thesis) awarded per full-time T-TT faculty M.S. degrees (non-thesis) awarded per full-time T-TT facultyPh.D. degrees awarded per full-time T-TT faculty

MAE: BY THE NUMBERS

Undergraduate student enrollment • Aerospace Engineering

• Mechanical Engineering

B.S. degrees awarded per full-time T-TT faculty Starting salary

• Aerospace Engineering • Mechanical Engineering

919

224215

704

7.28

$64,855

$63,770

UNDERGRADUATE251

51

120

24

56

1530188212

62012

16177%2.530.560.94

0.33

GRADUATE

Full time T-TT/NTT faculty Undergraduate to graduate student ratio Undergraduate student to full-time T-TT faculty ratio Journal articles per full-time T-TT facultyAwarded funds per full-time T-TT facultyExpenditures per full-time T-TT faculty Professional society fellows Minority and female faculty

36/43.6625.52.75

$210,490 $158,919

133

GENERAL


919

224215

704

7.28

$64,855

$63,770

TWO FACULTY RECEIVED NSF CAREER AWARDSIn 2016, Drs. Gao and Yang, assistant professors of mechanical engineering, received the National Science Foundation’s most prestigious award for young faculty members.The Faculty Early Career Development (CAREER) Award is National Science Foundation’s “most prestigious award in support of junior faculty who exemplify the role of teacher-scholars through outstanding research, excellent education and the integration of education and research within the context of the mission of their organizations.” Both faculty will be receiving approximate $500,000 over the next five years in support of their research.

Dr. Jie Gao’s award is in support of her research “Flat Singular Optics: Generation and Detection of Optical Vortex Beams with Plasmonic Metasurfaces in Linear and Nonlinear Regimes.” The current open research challenges in singular optics are how to generate pure vortices with broad bandwidth and polarization singular beams on chip, how to realize compact linear and nonlinear vortex beam converters, and what

kind of device enables direct identification of vortex topological charges. Supported by this award, Dr. Gao will conduct research work to explore flat singular optics, generate singular optical beams in both linear and nonlinear regimes, as well as detect vortex beam orbital angular momentum with optoelectronic integration. This research paves the way for advancing many applications in optical communications, beam shaping and conversion, optoelectronic devices, and optical sensing images.

Dr. Xiaodong Yang’s award is to support his research on “Light Manipulation in Metal-Dielectric Multilayer Metamaterials with Large Anisotropy.” Metamaterials are artificially structured composite materials with properties significantly different from those of the natural materials. “In optics, the permittivity, a measure of how an electric field affects and is affected by a medium,

of a material is an important measure of its ability to store electromagnetic energy and to convert electromagnetic energy into heat. Therefore, it affects the propagation and manipulation of light,” Yang says.

Yang explains, “The permittivities of most natural materials are usually isotropic, having the same value in all directions, with positive values for dielectric or transparent materials such as air and glass, and negative values for noble metals such as gold and silver.” By placing transparent and metallic thin layers in alternating order, optical multilayer metamaterials are created with permittivities that could not be realized using materials that occur in nature. Yang will use the multilayer metamaterials to study novel phenomena of light propagation and manipulation and to advance innovative applications using new kinds of metamaterials.

Dr. Gao joined the Missouri S&T faculty in 2012 from Columbia University, where she earned a Ph.D. in applied physics. Dr. Yang joined the faculty in 2011 from the University of California, Berkeley. He earned a Ph.D. in mechanical engineering from Columbia University in 2009. Dr. Yang also received the 2016 Office of Naval Research Young Investigator Award for his optical metasurfaces research.


Education: Ph.D., Purdue University

Research Interests: Multidimensional radiative heat transfer, laser processing of materials, radiative heat transfer in combustion processes, microscale heat transfer, biomedical optics, interaction of radiation with conduction and convection, multiple scattering and polarization of laser beams, solutions of integral equations, numerical heat transfer

DR. AL CROSBIECURATORS’ DISTINGUISHED PROFESSOR OF

MECHANICAL ENGINEERING Fellow, ASME, 1987Fellow, AIAA, 1988Fellow, AAAS, 1999

Education: Ph.D., University of Illinois at Urbana-Champaign

Research Interests: Combustion, laser based diagnostics for sprays and combustion, optical measurement systems, fuel injection, internal combustion engines

DR. JAMES A. DRALLMEIERCURATORS’ DISTINGUISHED TEACHING

PROFESSOR OF MECHANICAL ENGINEERINGDEPARTMENT CHAIR

Education: Ph.D., Clemson University

Research Interests: Aircraft structures, fracture mechanics, fatigue and failure analysis, micro mechanics, composite materials and structures, process modeling of ceramic matrix composites, friction and wear of composites, fracture of laminated glazing

DR. LOKESWARAPPA R. DHARANICURATORS’ DISTINGUISHED PROFESSOR OF MECHANICAL

AND AEROSPACE ENGINEERINGAssociate Fellow, AIAA, 1995

Fellow, ASME, 2000

Education: Ph.D., University of Texas at Austin

Research Interests: Stochastic estimation and control theory; information theory; nonlinear uncertainty propagation and rectification; autonomous guidance, navigation, and control of aerospace vehicles; orbit determination, data association, conjunction assessment, and collision avoidance; attitude dynamics, determination, and control; autonomous sensor management; high-fidelity dynamical and observational modeling

DR. KYLE DEMARSASSISTANT PROFESSOR OF AEROSPACE ENGINEERING

Education: Ph.D., Zhejiang University

Research Interests: Additive manufacturing, nanomanufacturing, smart manufacturing, solidification processing, laser materials processing, metal matrix nanocomposites, metallic glasses, materials for energy efficiency, materials for additive manufacturing, mechanical behavior of materials, and synchrotron radiation based x-ray scattering/imaging

DR. LIANYI CHEN ASSISTANT PROFESSOR OF

MECHANICAL ENGINEERING

FACULTY

Education: Ph.D., University of Illinois at Chicago

Research Interests: Design optimization, multidisciplinary optimization design, probabilistic/statistical methods, system/structural reliability, robust design, kinematics, mechanism synthesis, petroleum machinery

DR. XIAOPING DUCURATORS’ DISTINGUISHED TEACHING

PROFESSOR OF MECHANICAL ENGINEERING

Education: Ph.D., Technion (Israel) Research Interests: Composite material structures, biomechanics, smart structures and materials, structural dynamics and vibration, buckling and dynamic stability

DR. VICTOR BIRMANPROFESSOR OF MECHANICAL ENGINEERING

DIRECTOR OF ENGINEERING EDUCATION CENTERFellow, ASME, 1996

Education: Ph.D., University of Texas at Austin Research Interests: Guidance, stability, control and estimation, pattern recognition, stochastic processes, optimization, neural network applications to control, numerical methods, design

DR. S. N. BALAKRISHNANCURATORS’ DISTINGUISHED PROFESSOR

OF AEROSPACE ENGINEERINGDIRECTOR, NASA-MISSOURI SPACE GRANT

CONSORTIUM

Education: Ph.D., Virginia Polytechnic Institute and State University Research Interests: Composite materials, smart structures, nanocomposites, biocomposites, structural dynamics, finite element analysis, damage monitoring, composite manufacturing, experimental characterization

DR. K. CHANDRASHEKHARACURATORS’ DISTINGUISHED PROFESSOR OF

MECHANICAL AND AEROSPACE ENGINEERINGFellow, ASME, 2002

Education: Ph.D., University of Illinois at Urbana-Champaign Research Interests: Dynamic modeling and control of micro- and nano-positioning systems, atomic force microscopes and additive manufacturing systems; volumetric error compensation; iterative learning control, multi-dimensional control and signal processing

DR. DOUGLAS A. BRISTOWASSOCIATE PROFESSOR OF

MECHANICAL ENGINEERINGDIRECTOR OF CENTER FOR

AEROSPACE MANUFACTURING TECHNOLOGIES (CAMT)



Research Interests: Fluid dynamics, heat transfer, and thermodynamics of energy systems, heat and mass transfer in buoyant flows, second-law and exergy analysis, numerical simulation of transport phenomena and experimental methods

DR. KELLY HOMANASSOCIATE PROFESSOR OF


Education: Ph.D., Columbia University

Research Interests: Nanophotonics devices based on silicon photonics, plasmonics and metamaterials; light-matter interactions in photonic nanostructures; optical sensing; quantum dots; quantum optics and quantum information processing; solar energy harvesting; light emitting devices

DR. JIE GAOASSISTANT PROFESSOR OF


Education: Ph.D., Princeton University

Research Interests: Direct numerical simulation and large eddy simulation, high-speed transitional and turbulent flows, chemically reacting flows, laminar flow control and turbulent drag reduction, and large-scale, high performance computing

DR. LIAN DUANASSISTANT PROFESSOR OF AEROSPACE ENGINEERING

Education: Ph.D., Virginia Polytechnic Institute and State University

Research Interests: Computational fluid dynamics (CFD), aerodynamics, micro/nano flows, stochastic CFD, uncertainty and error quantification in computational simulations, multidisciplinary design and optimization, robust design, numerical methods

DR. SERHAT HOSDERASSOCIATE PROFESSOR OF AEROSPACE ENGINEERINGAssociate Fellow, AIAA, 2016

Education: Ph.D., Texas A&M University-College Station

Research Interests: Design theory and method-ology, design of complex systems, behavioral modeling of complex systems, design of hybrid powertrain systems, engineering software development, graphical simulations of engineering systems

DR. RYAN S. HUTCHESONASSOCIATE TEACHING PROFESSOR OF



Research Interests: Fluid dynamics, aero-structure interaction and control, intelligent aircraft, active flow control, unmanned air vehicles, electrochemical magnetohydrodynamics-based microfluidics and CFD simulations of transport phenomena

DR. KAKKATTUKUZHY M. ISAACPROFESSOR OF AEROSPACE ENGINEERING

ASSOCIATE CHAIR FOR AEROSPACE ENGINEERING

Education: Ph.D., New Mexico University

Research Interests: Nonlinear dynamics and vibrations, study of deterministic and random dynamical systems, model order reduction, theoretical modeling and numerical computation, structural dynamics

DR. NISHANT KUMAR ASSOCIATE TEACHING PROFESSOR OF


Education: Ph.D., University of Michigan at Ann Arbor

Research Interests: Combustion, air pollutants, alternative fuels, fuel cells, hydrogen technologies, radiative transfer, flame diagnostics, nanoparticle characterization, fire safety, thermal/fluid engineering

DR. UMIT O. KOYLUPROFESSOR OF MECHANICAL ENGINEERING


Research Interests: Infrared/optical antennas applied to energy transport, sensing, and manufacturing, metamaterials/frequency selective surfaces for engineering radiation properties, near-field radiation heat transfer, direct energy conversion and energy harvesting and laser based micro/nanomanufacturing including electronics packaging

DR. EDWARD C. KINZELASSISTANT PROFESSOR OF


FACULTY

DR. ROBERT G. LANDERSPROFESSOR OF MECHANICAL ENGINEERING

Fellow, ASME, 2014


Research Interests: Manufacturing, systems, and control; modeling, analysis, monitoring, and control of manufacturing processes; metal cutting; laser metal deposition; freeze extrusion fabrication; friction stir processing; electro–hydraulics; analysis and control of alternative energy systems; digital control applications


Education: Ph.D., Michigan Technological University

Research Interests: Manufacturing including intelligent machining, high speed machining, machine tool dynamics and metrology, metal forming, sensors and signal processing, computer numerical control, virtual manufacturing, and neural network applications; smart structures including structural health monitoring, aging aircraft, damage assessment and repair of metallic and composite structures, non-destructive evaluation, and proton exchange membrane (hydrogen) fuel cells

DR. ANTHONY OKAFORPROFESSOR OF MECHANICAL ENGINEERING


Research Interests: Astrodynamics, orbital mechanics, spacecraft design, spacecraft mission design, satellite attitude dynamics, nonlinear analysis, dynamics and control, optimization

DR. HENRY (HANK) PERNICKA

PROFESSOR OF AEROSPACE ENGINEERINGDEAN’S EDUCATOR SCHOLAR

Education: Ph.D., University of Texas at Arlington

Research Interests: Kinematics, mechanical design, synthesis of mechanisms

DR. J. KEITH NISBETTASSOCIATE PROFESSOR OF

MECHANICAL ENGINEERING ASSOCIATE CHAIR FOR MECHANICAL ENGINEERING

Education: Ph.D., University of Minnesota at Twin Cities

Research Interests: Mechanical design, rigid-body and compliant mechanism design, high-performance machinery analysis and design, machine vibration and stability

DR. ASHOK MIDHAPROFESSOR OF MECHANICAL ENGINEERING

DIRECTOR OF THE PRODUCT INNOVATION AND CREATIVITY CENTER

Fellow, ASME, 2003

Education: Ph.D., University of California at Berkeley

Research Interests: Additive manufacturing, electronics and photonics manufacturing, thermal/laser assisted manufacturing, laser annealing and crystallization, high-throughput and low cost micro/nano-manufacturing, solution processing of nanomaterials, molecular dynamics simulation, transport phenomena in nanomanufacturing processes

DR. HENG PANASSISTANT PROFESSOR OF



Research Interests: Advanced li-ion battery, beyond li-ion battery, energy storage systems, renewable energy systems, grid energy storage systems, nano-/macro-mechanics of materials, self-assembly of nanoparticles, nanostructures, multiphysics/multiscale experiment and simulations

DR. JONGHYUN PARKASSISTANT PROFESSOR OF


FACULTY


Research Interests: CAD/CAM, rapid prototyping, rapid manufacturing, fuel cell manufacturing

DR. FUEWEN (FRANK) LIOUMICHAEL AND JOYCE BYTNAR PRODUCT

INNOVATION AND CREATIVITY PROFESSOR OF MECHANICAL ENGINEERINGDIRECTOR OF MANUFACTURING

ENGINEERING PROGRAMFellow, ASME, 2008


Research Interests: Rapid prototyping, intelligent manufacturing, virtual reality, CAD/CAM, robotics, mechatronics and automatic control

DR. MING C. LEUKEITH AND PAT BAILEY DISTINGUISHED

PROFESSOR OF MECHANICAL ENGINEERINGDIRECTOR OF INTELLIGENT SYSTEMS CENTER (ISC)

Fellow, ASME, 1993 Fellow, International Academy of

Production Engineering (CIRP), 2008


Research Interests: Finite elasticity, viscoelasticity, liquid crystal hydrodynamics, solid and continuum mechanics

DR. GEAROID MACSITHIGHASSOCIATE PROFESSOR OF MECHANICAL

AND AEROSPACE ENGINEERING

Education: Ph.D., Missouri University of Science and Technology

Research Interests: Effective teaching of critical thinking and multidimensional problem solving, meta-cognition, innovative engine design, innovative sustainable spacecraft design, solar physics

DR. WARNER MEEKSASSISTANT TEACHING PROFESSOR OF

MECHANICAL AND AEROSPACE ENGINEERING



Research Interests: Fluid dynamics, computational fluid dynamics, hypersonic propulsion systems, computational analysis of jet mixing, flow losses and mixing enhancement in combustors, aircraft gas turbine ramjet propulsion systems, scramjet performance

DR. DAVID W. RIGGINSCURATORS’ TEACHING PROFESSOR

OF AEROSPACE ENGINEERING

Education: Ph.D., University of Michigan

Research Interests: Plasma aerospace applications, advanced space propulsion, plasma aerodynamics and flow control, plasma-enhanced combustion, applications to energy systems, hypersonics/re-entry body plasma interactions, plasma physics, rarefied gas dynamics

DR. JOSHUA L. ROVEYASSOCIATE PROFESSOR OF AEROSPACE ENGINEERING

ASSOCIATE CHAIR FOR GRADUATE AFFAIRSDEAN’S SCHOLAR

Fellow, NASA Innovation Advanced Concept, 2014Associate Fellow, AIAA, 2014

Education: Ph.D., University of Minnesota

Research Interests: Design theory, materials and structures, educational research

DR. JILLIAN SCHMIDTASSISTANT TEACHING PROFESSOR OF


Education: Ph.D., Massachusetts Institute of Technology

Research Interests: Physical human-robot interaction (pHRI), physical human-human interaction (pHHI), human movement assistance, rehabilitation robotics, wearable devices, energy-harvesting from human movement, design and instrumentation of medical devices

DR. YUN SEONG SONGASSISTANT PROFESSOR OF



Research Interests: Fluid dynamics, micro/nano-scale heat and mass transport, interfacial phenomena, micro/nanofluidics, bioMEMS, lab-on-a-chip, micro/nano-fabrication, bubble dynamics, droplet dynamics, acoustics, acoustic streaming, electrohydrodynamics, electrokinetics, and multi-phase flow

DR. CHENG WANGASSISTANT PROFESSOR OF



Research Interests: Ultrashort laser pulse-material interaction, laser micromachining for micro-sensors and micro-devices, gas metal arc welding, laser welding and hybrid welding, Ab Initio MD modeling, multiscale modeling

DR. HAI-LUNG TSAIPROFESSOR OF MECHANICAL ENGINEERING

Fellow, ASME, 2009

Education: Ph.D., Columbia University

Research Interests: Optical materials and devices in nanophotonics and plasmonics; physics and applications of optical meta-materials; nanoscale optomechanics, optical nanoelectromechanical systems (NEMS); integrated optofluidic devices and optical sensors; photon management for solar/thermal energy harvesting; optical device micro-/nano-fabrication

DR. XIAODONG YANGASSISTANT PROFESSOR OF

MECHANICAL ENGINEERINGDEAN’S SCHOLAR

FACULTY


Research Interests: Dynamics, vibrations, modeling and development of piezoactuators and transducers-mechatronics, embedded systems and control

DR. DANIEL S. STUTTSASSOCIATE PROFESSOR OF


Education: Ph.D., California Institute of Technology

Research Interests: Aerospace structures, active materials, mechanics of materials, continuum mechanics, micromechanics, manufacturing, experimental and computational solid mechanics

DR. CHARLES S. WOJNARASSISTANT PROFESSOR OF AEROSPACE ENGINEERING


Balakrishnan, S.

Balakrishnan, S. (100%), NASA Goddard Space Flight Center, “Development of Turbulence Models, Uncertainty Quantification and Optimization Tools for Aircraft and Turbomachinery Analysis and Design,” supplement January 29, 2016, $430,973, October 1, 2014 - September 30, 2017.

Liou, F. (65%), Balakrishnan, S. (10%) and Newkirk, J. (25%), NASA, “Fabrication of Advanced Materials for Space Applications,” $65,554, September 1, 2013 - August 31, 2016.

Balakrishnan, S. (100%), NASA Goddard Space Flight Center, “Missouri Space Grant Consortium,” continuation November 15, 2016, $231,000, May 1, 2015 - April 30, 2018.

Balakrishnan, S. (100%), Indiana University, “Applications of Quantum Decision Theory to Target Assignments,” continuation December 19, 2016, $58,267, September 30, 2015 - September 29, 2017.

Balakrishnan, S. (100%), NASA Goddard Space Flight Center, “Experimental Program to Stimulate Competitive Research (EPSCoR) - Research Infrastructure Development (RID),” continuation December 7, 2016, $68,750, May 6, 2015 - May 5, 2018.

Bristow, D.

Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), Honeywell Federal Manufacturing and Technologies, LLC, “Frequency Response Inspection of Additively Manufactured Parts for Defect Identification,” $79,778, January 13 - September 30, 2016.

Leu, M. (25%), Bristow, D. (9%), Chen, L. (5%), Kinzel, E. (12%), Landers, R. G. (9%), Liou, F. (15%), Newkirk, J. (20%) and O’Malley, R. (5%), Honeywell Federal Manufacturing and Technologies, LLC, “Metal Additive Manufacturing Materials Analysis for Missouri University of Science and Technology,” supplement February 4, 2016, $817,381, May 7, 2015 - September 13, 2016.

Bristow, D. (34%), Landers, R. G. (33%) and Leu, M. (33%), Caterpillar, Inc., “Integrated Manufacturing Variation Management (IMVM),” $276,287, February 5, 2016 - November 30, 2017.

Bristow, D. (50%) and Landers, R. G. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Thermally Varying Volumetric Error Compensation,” $40,000, January 1 - December 31, 2016.

Bristow, D. (50%), Landers, R. G. (40%) and Liou, F. (10%), National Science Foundation, “Iterative Process Control for Laser Metal Deposition,” supplement March 8, 2016, $5,000, June 1, 2013 - August 31, 2017.

Landers, R. G. (50%) and Bristow, D. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Robotic Volumetric Error Compensation Using Angular Measurement,” $25,000, January 1 - December 31, 2016.

Bristow, D. (50%) and Landers, R. G. (50%), EWI, “Laser-Directed Energy Deposition (LED) Process Monitoring and Control,” $20,000, March 1 - August 31, 2016.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan, H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education,

“GAANN: Doctoral Research and Training in Mechatronics,” continuation August 23, 2016, $295,368, September 1, 2015 - August 31, 2018.

Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), National Science Foundation, “GOALI: Additive Manufacturing of Glass Based Gradient Index Optics,” supplement August 4, 2016, $5,000, August 1, 2015 - July 31, 2018.

Bristow, D. (100%), IEEE Instrumentation and Measurement Society, “Control Systems Webinars: Reaching Broader Control Systems Community Around the Globe,” $19,800, February 1, 2016 - January 31, 2017.

Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), Honeywell Federal Manufacturing and Technologies, LLC, “Frequency Response Inspection of Additively Manufactured Parts for Defect Identification,” continuation December 13, 2016, $80,000, January 13, 2016 - September 30, 2017.

Chandrashekhara, K.

Leu, M. (50%) and Chandrashekhara, K. (50%), Center for Aerospace Manufacturing Technologies, “CAMT: Low-Cost Rapid FDM Tooling with ULTEM 1010,” $60,000, January 1 - December 31, 2016.

Chandrashekhara, K. (100%), Center for Aerospace Manufacturing Technologies, “CAMT: Evaluation and Testing of High Temperature Composite Sandwich Structure,” $20,000, January 1 - December 31, 2016.

Chandrashekhara, K. (34%), Lekakh, S. (33%) and Van Aken, D. (33%), Kent D. Peaslee Steel Manufacturing Research Center, “Peaslee-SMRC: Hot Working Modeling and Simulation of Highly Alloyed Steels,” $90,000, July 1, 2016 - June 30, 2017.

Leu, M. (50%) and Chandrashekhara, K. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Low-Cost Rapid FDM Tooling with ULTEM 1010,” continuation June 14, 2016, $72,000, January 1 - December 31, 2016.

Chandrashekhara, K. (100%), Technical Data Analysis, Inc., “Novel Multi-Scale/Multi-Physics Integrated Tool for the Prediction of Manufacturing-Induced Defects in Autoclave Composite Airframe Parts,” supplement July 29, 2016, $28,000, July 27, 2015 - October 24, 2016.

Chandrashekhara, K. (50%) and Wang, C. (50%), Center for Infrastructure Engineering Studies, Missouri University of Science and Technology, “Process Modeling of Composite Parts Using Autoclave,” $5,000, September 1, 2016 - August 31, 2017.

Chen, L.


Chen, L. (100%), National Science Foundation, “Nanoparticle-Enabled Mechanisms for Growth Control in Immiscible Alloys Under Regular Cooling,” $240,210, July 1, 2016 - June 30, 2019.

DeMars, K.

DeMars, K. (100%), NASA Johnson Space Center, “A Framework for Lander Navigation,” $30,000, February 16, 2016 - February 15, 2018.

Rovey, J. (30%), Pernicka, H. (30%), DeMars, K. (20%) and Kimball, J. (20%), Utah State University, “Multi-Mode MicroPropulsion CubeSat Technology Demonstration Mission,” $55,000, December 16, 2015 - May 8, 2017.

Pernicka, H. (35%), Rovey, J. (25%), DeMars, K. (20%) and Kimball, J. (20%), NASA Goddard Space Flight Center, “Use of Multi-Mode Propulsion to Expand CubeSat Mission Capabilities,” $199,911, May 9, 2016 - May 8, 2018.

DeMars, K. (100%), Applied Technology Association, “Trajectory Reconstruction Algorithms for Consistent Event Registration (TRACER),” $200,000, July 8, 2016 - June 6, 2018.

DeMars, K. (100%), NASA Johnson Space Center, “A Framework for Lander Navigation,” continuation August 30, 2016, $25,000, February 16, 2016 - February 15, 2018.

DeMars, K. (100%), NASA Goddard Space Flight Center, “Multitarget Approaches to Robust Navigation,” $66,718, August 1, 2016 - July 31, 2020.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan, H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” continuation August 23, 2016, $295,368, September 1, 2015 - August 31, 2018.

Du, X.

Du, X. (100%), National Science Foundation, “Reliability Prediction for System Designs with Outsourced Components,” $217,319, August 1, 2016 - July 31, 2019.

Duan, L.

Duan, L. (100%), National Institute of Aerospace, “Numerical Simulation of Transitional and Turbulent Flows,” $1,710, January 25, 2016 - January 1, 2017.

Duan, L. (100%), Air Force Office of Scientific Research, “Numerical Simulation of Freestream Acoustic Disturbances in Hypersonic Ground Facilities and Their Effect on Boundary Layer Transition,” continuation May 6, 2016, $135,587, July 1, 2014 - June 30, 2017.


Duan, L. (100%), National Science Foundation, “DNS of Pressure Fluctuations Induced by Supersonic Turbulent Boundary Layers,” $6,326, September 1, 2016 - August 31, 2018.

Duan, L. (100%), National Institute of Aerospace, “Direct Numerical Simulations of Receptivity to Roughness in a Swept-Wing Boundary Layer,” $29,977, September 12, 2016 - September 11, 2017.

NEW GRANTS AND CONTRACTS


Eversman, W.

Eversman, W. (100%), Spirit Aerospace, Inc., “Spirit Aerosystems Acoustic Lining Modeling,” $75,050, December 15, 2015 - May 14, 2016.

Gao, J.

Rovey, J. (34%), Pernicka, H. (22%), Gao, J. (22%) and Yang, X. (22%), NASA Goddard Space Flight Center, “Experimental Demonstration and System Analysis for Plasmonic Force Propulsion,” $249,246, August 1, 2016 - July 31, 2018.

Rovey, J. (34%), Pernicka, H. (22%), Gao, J. (22%) and Yang, X. (22%), NASA Goddard Space Flight Center, “Experimental Demonstration and System Analysis for Plasmonic Force Propulsion,” continuation October 13, 2016, $200,000, August 1, 2016 - July 31, 2018.

Gao, J. (100%), National Science Foundation, “CAREER: Flat Singular Optics: Generation and Detection of Optical Vortex Beams with Plasmonic Metasurfaces in Linear and Nonlinear Regimes,” $500,011, February 1, 2017 - January 31, 2022.

Hosder, S.

Hosder, S. (100%), NASA Goddard Space Flight Center, “Uncertainty Quantification Applied to the Analysis and Design of Hypersonic Inflatable Atmospheric Decelerators for Spacecraft Re-Entry,” continuation July 13, 2016, $40,000, August 1, 2013 - July 31, 2017.

Kinzel, E.



Kinzel, E. (100%), Air Force Research Lab, “Additive Manufacturing of GRIN Optics,” $74,999, June 15, 2016 - September 20, 2017.




Landers, R. G.




Bristow, D. (50%) and Landers, R. G. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Thermally Varying Volumetric Error Compensation,” $40,000, January 1 - December 31, 2016.


Landers, R. G. (50%) and Bristow, D. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Robotic Volumetric Error Compensation Using Angular Measurement,” $25,000, January 1 - December 31, 2016.

Bristow, D. (50%) and Landers, R. G. (50%), EWI, “Laser-Directed Energy Deposition (LED) Process Monitoring and Control,” $20,000, March 1 - August 31, 2016.




Park, J. (50%), Kimball, J. (25%) and Landers, R. G. (25%), National Science Foundation, “Optimal Energy Scheduling in Microgrids with Photovoltaic (PV) Generation and Energy Storarge Systems,” $315,301, September 1, 2016 - August 31, 2019.

Leu, M.

Leu, M. (50%) and Chandrashekhara, K. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Low-Cost Rapid FDM Tooling with ULTEM 1010,” $60,000, January 1 - December 31, 2016.


Leu, M. (100%), Center for Aerospace Manufacturing Technology, “CAMT: Robotic Volumetric Error Compensation Using Angular Measurement Thrust,” $25,000, January 1 - December 31, 2016.

Leu, M. (100%), Center for Aerospace Manufacturing Technology, “CAMT: Program Support,” $76,000, January 1 - December 31, 2016.

Leu, M. (100%), Siemens CNX, “Create an NX10 version of NX for Engineering Design,” $25,000, October 1, 2015 - March 31, 2017.


Long, S. (28%), Leu, M. (20%), Qin, R. (26%) and Konur, D. (26%), Missouri Department of Transportation, “Work Zone Simulator Analysis: Driver Performance and Acceptance of Missouri Alternate Lane Shift Configurations,” $75,009, May 1 - December 31, 2016.

Leu, M. (100%), Product Innovation and Engineering, LLC, “CAMT: Product Innovation and Engineering Membership,” $50,000, March 15, 2016 - March 14, 2017.

Leu, M. (100%), Center for Aerospace Manufacturing Technologies, “CAMT: Program Support,” supplement April 13, 2016, $10,000, January 1 - December 31, 2016.

Leu, M. (100%), Center for Aerospace Manufacturing Technologies, “CAMT: API Membership,” April 25, 2016, $25,000, August 1, 2015 - July 13, 2017.

Tsai, H. (60%) and Leu, M. (40%), Department of Energy, “Additive Manufacturing of Smart Parts with Embedded Sensors for In-Situ Monitoring in Advance,” continuation May 5, 2016, $300,000, October 1, 2013 - September 30, 2016.

Leu, M. (50%) and Chandrashekhara, K. (50%), Center for Aerospace Manufacturing Technologies, “CAMT: Low-Cost Rapid FDM Tooling with ULTEM 1010,” continuation June 14, 2016, $72,000, January 1 - December 31, 2016.


Leu, M. (100%), Siemens CNX, “Create an NX10 Version of NX for Engineering Design,” continuation September 22, 2016, $6,000, October 1, 2015 - December 31, 2017.

Leu, M. (100%), Center for Aerospace Manufacturing Technology, “An Exploratory Study of Selective Laser Melting for Bonding of 304L Stainless Steel to Cast Iron,” $12,000, September 1 - December 31, 2016.


Yin, Z. (45%), Qin, R. (35%) and Leu, M. (20%), National Science Foundation, “CPS: Synergy: Collaborative Research: Cyber-Physical Sensing, Modeling and Control with Augmented Reality for Smart Manufacturing Workforce Training and Operations Management,” $490,287, February 1, 2017 - February 1, 2018.

Yin, Z. (45%), Qin, R. (35%) and Leu, M. (20%), National Science Foundation, “CPS: Synergy: Collaborative Research: Cyber-Physical Sensing, Modeling and Control with Augmented Reality for Smart Manufacturing Workforce Training and Operations Management,” Participant Support, $15,000, February 1, 2017 - February 1, 2018.

Liou, F.

Liou, F. (65%), Balakrishnan, S. (10%) and Newkirk, J. (25%), NASA, “Fabrication of Advanced Materials for Space Applications,” $65,554, September 1, 2013 - August 31, 2016.

Liou, F. (100%), EWI, “Investigation of a Height Control Sensor for LMD,” $20,289, January 11 - December 31, 2016.

Liou, F. (100%), Center for Aerospace Manufacturing Technology, “CAMT: Simulation of a Laser Wire Deposition Process for Ti6Al4V Components,” $40,000, January 1 - December 31, 2016.

Liou, F. (100%), Center for Aerospace Manufacturing Technology, “CAMT: Evaluation of Die Repair Using Metal Deposition Process,” $40,000, January 1 - December 31, 2016.


Liou, F. (50%) and Newkirk, J. (50%), Center for Aerospace Manufacturing Technology, “CAMT: Fabrication of Ti-y-TiAI Functionally Gradient Materials,” $40,000, January 1 - December 31, 2016.


Liou, F. (100%), Center for Aerospace Manufacturing Technologies, “CAMT: Additive Manufacturing Simulator (AMS),” $40,000, March 15 - December 31, 2016.

Liou, F. (50%), Newkirk, J. (25%) and Sarangapani, J. (25%), National Science Foundation, “MRI: Development of an Advanced Materials Additive Manufacturing (AM2) System for Research and Education,” $881,018, September 1, 2016 - August 31, 2019.

Liou, F. (50%), Newkirk, J. (25%) and Sarangapani, J. (25%), National Science Foundation, “MRI: Development of an Advanced Materials Additive Manufacturing (AM2) System for Research and Education,” amendment December 2, 2016, $16,000, September 1, 2016 - August 31, 2019.

Pan, H.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan, H. (7%),

Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” continuation August 23, 2016, $295,368, September 1, 2015 - August 31, 2018.

Pan, H. (100%), National Science Foundation, “Fundamental Investigations of Femtosecond Laser Excitation of Functional Nanomaterials for Nano Additive Manufacturing,” $250,026, September 1, 2016 - August 31, 2019.

Pan, H. (100%), Worcester Polytechnic Institute, “PFI: AIR-TT: Scale-Up Dry-Powder Based Additive Manufactured Electrodes to Lower the Cost of Li-Ion Batteries,” $50,497, September 15, 2016 - September 14, 2017.

Park, J.

Wang, R. (66%) and Park, J. (34%), Center for Biomedical Science Engineering, Missouri University of Science and Technology, “Engineering DNA Nanostructure as a Smart Drug Delivery Carrier for Cancer Therapy,” $15,910, January 1 - December 31, 2016.

Park, J. (100%), National Science Foundation, “GOALI: Mechanically Strong and Electrochemically Robust Porous Electrodes for Batteries Using Micro-Additive Manufacturing,” $150,000, May 1, 2016 - April 30, 2019.

Park, J. (50%) and Liang, X. (50%), National Science Foundation, “Mechanical/Chemical Failure of Solid Electrolyte Interphase In Lithium-ion Batteries: Understanding Its Mechanisms and Suppressing Its Onset,” continuation July 20, 2016, $97,900, September 1, 2015 - August 31, 2018.

Dogan, F. (34%), Ferdowsi, M. (33%) and Park, J. (33%), Microgrid Industrial Consortium, “MIC: Novel Battery Materials for Efficient Change Profile and Energy Storage Management in Microgrids,” 60,000, June 1, 2016 - May 31, 2017.


Kim, C. (50%), Park, J. (50%) and Spencer, C. (0), Center for Biomedical Science Engineering, Missouri University of Science and Technology, “Biodegradable Optical Devices for Photodynamic Therapy,” $15,000, January 1 - December 31, 2017.

Park, J. (50%), Kimball, J. (25%) and Landers, R. G. (25%), National Science Foundation, “Optimal Energy Scheduling in Microgrids with Photovoltaic (PV) Generation and Energy Storarge Systems,” $315,301, September 1, 2016 - August 31, 2019.

Pernicka, H.






Rovey, J.

Rovey, J. (100%), NASA, “Multi-Mode MicroPropulsion for Small Spacecraft,” amendment March 31, 2016, $6,752, September 1, 2015 - August 31, 2016.



Rovey, J. (100%), University of Missouri System FastTrack Initiative, “Development and Commercialization of Multi-Mode Micropropulsion,” $50,000, July 1, 2016 - June 30, 2017.

Rovey, J. (100%), NASA Goddard Space Flight Center, “Characterization of a Green Solid Electric Microthruster for Small Spacecraft,” continuation July 22, 2016, $66,718, August 1, 2015 - July 31, 2019.


Rovey, J. (50%) and Yang, X. (50%), Air Force Research Lab, “Plasmonic Space Propulsion,” supplement July 18, 2016, $167,653, August 15, 2014 - August 14, 2017.



Stutts, D.

Stutts, D. (100%), Texas Instruments, “Gift Funding-Piezo Actuator Modeling and Ultrasonic Motor Control,” $65,000, January 1 - December 31, 2016.


Balakrishnan, S.

Yucelen, T. (60%) and Balakrishnan, S. (40%), NASA Goddard Space Flight Center, “Learning Algorithms for Preserving Safe Flight Envelope,” $716,538, September 1, 2015 - August 31, 2018.

Yucelen, T. (60%) and Balakrishnan, S. (40%), Wichita State University, “Active Wing Shaping Control of Morphing Aircraft,” $270,000, August 1, 2015 - July 31, 2018.

Balakrishnan, S. (100%), Indiana University, “Applications of Quantum Decision Theory to Target Assignments,” $55,374, September 30, 2015 - September 29, 2016.

Bristow, D.

Bristow, D. (50%), Landers, R. G. (40%) and Liou, F. (10%), National Science Foundation, “Iterative Process Control of Laser Metal Deposition,” $272,875, June 1, 2013 - May 31, 2016.

Landers, R. G. (50%) and Bristow, D. (50%), National Science Foundation, “GOALI: Volumetric Error Analysis for Machine Tools,” $300,000, August 1, 2013 - July 31, 2016.

Landers, R. G. (50%) and Bristow, D. (50%), National Science Foundation, “GOALI: Volumetric Error Analysis for Machine Tools,” amendment May 12, 2014, $5,000, August 1, 2013 - July 31, 2016.

Landers, R. G. (35%), Bristow, D. (5%), Chen, L. (10%), Hilmas, G. (5%), Kinzel, E. (10%), Leu, M. (5%), Liou, F. (5%), Newkirk, J. (5%), Pan, H. (10%) and Park, J. (10%), National Science Foundation, “REU Site: Additive Manufacturing,” $415,000, April 1, 2015 - March 31, 2018.

Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), National Science Foundation, “GOALI: Additive Manufacturing of Glass Based Gradient Index Optics,”

$300,000, August 1, 2015 - July 31, 2018.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan, H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” $295,278, September 1, 2015 - August 31, 2016.

Chandrashekhara, K.

Chandrashekhara, K. (45%) and Nam, P. (55%), Missouri Soybean Merchandising Council, “Energy Efficient Building Panels with Insulation Core of Soy-Based Polyurethane Foams,” $30,000, April 1, 2015 - March 31, 2016.

Chandrashekhara, K. (100%), Technical Data Analysis, Inc., “Novel Multi-Scale/Multi-Physics Integrated Tool for the Prediction of Manufacturing-Induced Defects in Autoclave Composite Airframe Parts,” $32,000, July 27, 2015 - January 15, 2016.

Chen, L.


Chen, L. (100%), University of Missouri Research Board, “Observing Defects Formation in Selective Laser Melting,” $58,183, January 4, 2016 - May 31, 2017.

DeMars, K.

DeMars, K. (100%), Air Force Research Laboratory, “External Aiding Methods for IMU-Based Navigation,” $100,000, August 27, 2014 - August 26, 2016.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan,

H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronicsv,” $295,278, September 1, 2015 - August 31, 2016.

Rovey, J. (30%), Pernicka, H. (30%), DeMars, K. (20%) and Kimball, J. (20%), Utah State University, “Multi-Mode MicroPropulsion CubeSat Technology Demonstration Mission,” $3,400, December 16, 2015 - December 31, 2016.

Drallmeier, J.

Drallmeier, J. (100%), Kawasaki Motors Manufacturing Corporation, “Small Engine Heat Transfer,” $205,860, November 15, 2014 - November 14, 2016.

Midha, A. (75%) and Drallmeier, J. (25%), Par-Way Tryson, “The Design and Development of a New Manual Trigger Sprayer for Dispensing Vegetable Oil from a Bottle,” $155,690, August 1, 2015 - September 30, 2016.

Du, X.

Du, X. (70%) and Takai, S. (30%), National Science Foundation Undergraduate Education, “Engineering Uncertainty Repository,” $199,879, June 15, 2013 - May 31, 2017.

Du, X. (100%), National Science Foundation, “Quantitative Reliability Prediction in Early Design Stages,” $190,265, August 1, 2013 - July 31, 2016.

Duan, L.

Duan, L. (100%), Air Force Office of Scientific Research, “Numerical Simulation of Freestream Acoustic Disturbances in Hypersonic Ground Facilities and Their Effect on Boundary Layer Transition,” $134,869, July 1, 2015 - June 30, 2016.


OTHER ACTIVE GRANTS AND CONTRACTS

Stutts, D. (100%), Texas Instruments, “Piezoactuator Drive and Control Research and Development,” $147,277, April 1, 2016 - September 30, 2017.

Tsai, H.

Tsai, H. (60%) and Leu, M. (40%), Department of Energy, “Additive Manufacturing of Smart Parts with Embedded Sensors for In-Situ Monitoring in Advance,” continuation May 5, 2016, $300,000, October 1, 2013 - September 30, 2016.

Tsai, H. (100%), University of Missouri System FastTrack Initiative, “3D Printing for Amorphous Metal Structures,” $50,000, June 1, 2016 - May 31, 2017.

Wang, C.

Wang, C. (37%), Park, J. (31.5%) and Barua, S. (31.5%), Center of Biological Science and Engineering, Missouri University of Science and Technology, “Study of Interstitial Nanoparticle Flow in a Tumor-on-a-Chip,” $18,500, January 1 - December 31, 2016.

Chandrashekhara, K. (50%) and Wang, C. (50%), Center for Infrastructure Engineering Studies, Missouri University of Science and Technology, “Process Modeling of Composite Parts Using Autoclave,” $5,000, September 1, 2016 - August 31, 2017.

Wojnar, C.

Wojnar, C. (100%), University of Missouri Research Board, “Cryogenic Testing of Ferroelectrics for Use in Space,” $43,033, May 25, 2016 - May 24, 2017.

Yang, X.

Yang, X. (100%), Office of Naval Research, “Negative Optical Torque Generation in Plasmonic and Dielectric Metasurfaces,” $85,000, June 1, 2016 - May 31, 2019.

Yang, X. (100%), National Science Foundation, “CAREER: Extraordinary Light Propagation in Metal-Dielectric Multilayer Epsilon-Near-Zero Metamaterials,” $88,250, June 1, 2016 - May 31, 2017.

Rovey, J. (50%) and Yang, X. (50%), Air Force Research Lab, “Plasmonic Space Propulsion,” supplement July 18, 2016, $167,653, August 15, 2014 - August 14, 2017.



Yang, X. (100%), Army Research Office, “Enhancement of Light Trapping and Optical Absorption in Complex ZnO Nanostructures,” $50,000, September 1, 2015 - May 31, 2016.


H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” $295,278, September 1, 2015 - August 31, 2016.

Finaish, F.

Finaish, F. (10%), Liou, F. (65%) and Newkirk, J. (25%), NASA Goddard Space Flight Center, “Fabrications of Advance Materials for Space Applications,” $750,000, September 1, 2013 - August 31, 2016.

Gao, J.

Yang, X. (50%) and Gao, J. (50%), National Science Foundation, “Infrared Perfect Absorbers and Thermal Emitters with Tunable Bandwidth Based on Metamaterial,” $304,912, June 15, 2014 - May 31, 2017.

Hosder, S.

Hosder, S. (100%), NASA Goddard Space Flight Center, “Uncertainty Quantification Applied to the Analysis and Design of Hypersonic Inflatable Atmospheric Decelerators for Spacecraft Re-entry,” amendment June 1, 2014, $65,917, June 4, 2014, August 1, 2013 - July 31, 2017.

Hosder, S. (100%), NASA Glenn Research Center, “Development of Turbulence Models, Uncertainty Quantifcation and Optimization Tools for Aircraft and Turbomachinery Analysis and Design,” $211,764, October 1, 2014 - September 30, 2017.

Hosder, S. (100%), National Aeronautics and Space Administration, “Uncertainty Quantification Applied to the Analysis and Design of Hypersonic Inflatable Atmospheric Decelerators for Spacecraft,” supplement, June 18, 2014, $68,934, August 1, 2013 - July 31, 2017.

Huang, X.

Huang, X. (100%), University of Missouri System Interdisciplinary Intercampus Research Program, “An Impedance Self-Adaptive Skin-Complaint RF Power Scavenger For Mobile Healthcare and Human-Machine Interface,” $81,000, August 1, 2015 - July 31, 2016.

Huang, X. (100%), University of Missouri Research Board, “Photonically Sintered Bioresorbable Electronic Devices,” $60,630, January 20, 2016 - January 19, 2017.

Isaac, K.

Isaac, K. (100%), National Science Foundation, “Collaborative Research: Actively Controllable Microfluidics with Filmed-Confined Redox-Magnetohydrodynamics: Experiment and Simulation,” $165,395, September 1, 2013 - August 31, 2016.

Kinzel, E.


Kinzel, E. (100%), University of Missouri System Interdisciplinary Intercampus Research Program, “Metasurface Enabled

Advanced Microbolometer Architecture for Infrared Sensing and Fundamental Thermal Transport Investigation,” $80,000, August 1, 2015 - July 31, 2016.

Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), National Science Foundation, “GOALI: Additive Manufacturing of Glass Based Gradient Index Optics,” $300,000, August 1, 2015 - July 31, 2018.

Pan, H. (15%), Switzer, J. (40%), Hor, Y. (15%), Kinzel, E. (15%) and Nath, M. (15%), National Science Foundation, “MRI: Acquisition of an Electron-Beam Lithography System for Nanofabrication and Nanoscience,” $840,000, September 1, 2015 - August 31, 2017.

Kinzel, E. (100%), National Science Foundation, “Metasurface Enabled Uncooled Silicon Germanium Oxide (SixGeyO1-x-y) Microbolometers for Multispectral Infrared Imaging,” $129,508, September 15, 2015 - August 31, 2018.


Koylu, U.

Koylu, U. (100%), National Science Foundation, “Bio-Inspired Flow Field Designs for PEM Fuel Cells,” $50,000, July 1, 2015 - March 31, 2016.

Landers, R. G.


Landers, R. G. (50%) and Bristow, D. (50%), National Science Foundation, “GOALI: Volumetric Error Analysis for Machine Tools,” $300,000, August 1, 2013 - July 31, 2016.

Landers, R. G. (50%) and Bristow, D. (50%), National Science Foundation, “GOALI: Volumetric Error Analysis for Machine Tools,” amendment May 12, 2014, $5,000, August 1, 2013 - July 31, 2016.


Kinzel, E. (50%), Bristow, D. (25%) and Landers, R. G. (25%), National Science Foundation, “GOALI: Additive Manufacturing of Glass Based Gradient Index Optics,” $300,000, August 1, 2015 - July 31, 2018.

Park, J. (50%) and Landers, R. G. (50%), National Science Foundation, “Battery Health Dynamics and Its Management,” $412,559, September 1, 2015 - August 31, 2018.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Pan, H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research

and Training in Mechatronics,” $295,278, September 1, 2015 - August 31, 2016.

Leu, M.

Leu, M. (20%), Long, S. (30%), Smith, B. (25%) and Konur, D. (25%), Missouri Department of Transportation, “Work Zone Simulator Analysis: Driver Performance and Acceptance of Alternate Merge Sign Configuration,” $120,237, October 1, 2014 - June 15, 2016.


Leu, M. (100%), Spirit Aerosystem, Inc., “CAMT: Spirit Membership,” $50,000, May 11, 2015 - May 10, 2016.

Tsai, H. (60%) and Leu, M. (40%), Department of Energy, “Additive Manufacturing of Smart Parts with Embedded Sensors for In-Situ Monitoring in Advanced Energy Systems,” $250,00, October 1, 2013 - September 30, 2016.

Leu, M. (100%), Cummins, “ CAMT: Cummins Membership,” $15,000, October 9, 2015 - October 8, 2016.

Leu, M. (100%), Bodine Aluminum, Inc., “CAMT: Bodine Aluminum, Inc. Membership,” $50,000, October 9, 2015 - January 8, 2017.

Leu, M. (50%) and Cheng, M. (50%), University of Arkansas, “EAGER: Cybermanufacturing: Architecture and Protocols for Scalable Cyber-Physical Manufacturing System,” $172,933, September 1, 2015 - August 31, 2017.


Liou, F.


Finaish, F. (10%), Liou, F. (65%) and Newkirk, J. (25%), NASA Goddard Space Flight Center, “Fabrications of Advance Materials for Space Applications,” $750,000, September 1, 2013 - August 31, 2016.


Liou, F. (100%), National Science Foundation, “EAGER/Cybermanufacturing: Cyber-Enabled Additive Manufacturing of Advanced Materials,” $146,758, September 1, 2015 - August 31, 2017.

Liou, F. (60%) and Sarangapani, J. (40%), National Science Foundation, “EAGER: Cybermanufacturing: Cyber-Enabled Additive


Manufacturing of Advanced Materials,” $5,000, September 1, 2015 - August 31, 2017.

Midha, A.

Midha, A. (75%) and Drallmeier, J. (25%), Par-Way Tryson, “The Design and Development of a New Manual Trigger Sprayer for Dispensing Vegetable Oil From a Bottle,” $155,690, August 1, 2015 - September 30, 2016.

Midha, A. (100%), Missouri Department of Economic Development, “The Design and Development of a New Manual Trigger Sprayer for Dispensing Vegetable Oil From a Bottle,” $28,000, August 1 - October 31, 2015.

Pan, H.

Pan, H. (100%), National Science Foundation, “Collaborative Research: Directed Templating of Semiconductor Nanocrystals Through Laser Melting,” $110,000, July 1, 2014 - June 30, 2017.

Pan, H. (100%), National Science Foundation, “Collaborative Research: Battery Electrode Fabrication Through Innovative Powder-Based Additive Manufacturing,” $149,999, April 1, 2015 - March 31, 2018.


Pan, H. (15%), Switzer, J. (40%), Hor, Y. (15%), Kinzel, E. (15%) and Nath, M. (15%), National Science Foundation, “MRI: Acquisition of an Electron-Beam Lithography System for Nanofabrication and Nanoscience,” $840,000, September 1, 2015 - August 31, 2017.


Park, J.

Park, J. (100%), University of Missouri Research Board, “Failure Mechanisms of Interface Layers in Batteries,” $44,793, June 1, 2015 - May 31, 2016.


Park, J. (50%) and Liang, X. (50%), National Science Foundation, “Mechanical/Chemical Failure of Solid Electrolyte Interphase In Lithium-ion Batteries: Understanding Its Mechanisms and Suppressing Its Onset,” $99,586, September 1, 2015 - August 31, 2016.

Park, J. (50%) and Landers, R. G. (50%), National Science Foundation, “Battery Health Dynamics and Its Management,” $412,559, September 1, 2015 - August 31, 2018.


H. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” $295,278, September 1, 2015 - August 31, 2016.

Pernicka, H.

Rovey, J. (50%) and Pernicka, H. (50%), University of Missouri System Interdisciplinary Intercampus Research Program, “Multi-mode Rocket for CubeSats,” $50,000, August 1, 2015 - July 31, 2016.

Pernicka, H. (80%) and Rovey, J. (20%), Air Force Office of Scientific Research, “Development of a Validation of a Stereoscopic Imager and a Micropropulsion System for Use in Spacecraft Close Proximity Operations,” $110,000, September 14, 2015 - September 14, 2016.

Pernicka, H. (100%), M4 Engineering, Inc., “Multi-mode Rocket for CubeSats,” $37,500, June 17, 2015 - June 17, 2016.


Rovey, J. (30%), Pernicka, H. (30%), DeMars, K. (20%) and Kimball, J. (20%), Utah State University, “Multi-Mode MicroPropulsion CubeSat Technology Demonstration Mission,” $3,400, December 16, 2015 - December 31, 2016.

Riggins, D.

Riggins, D. (100%), NASA Glenn Research Center, “Development of Turbulence Models, Uncertainty Quantification and Optimization Tools for Aircraft and Turbomachinery Analysis and Design,” $538,236, November 1, 2014 - September 30, 2017.

Riggins, D. (100%), NASA Goddard Space Flight Center, “Experimental Program to Stimulate Competitive Research (EPSCoR) - Research Infrastructure Development,” $125,000, May 6, 2015 - May 5, 2016.

Riggins, D. (100%), NASA Goddard Space Flight Center, “Learning Algorithms for Preserving Safe Flight Envelope,” $33,399, September 15, 2015 - August 31, 2018.

Riggins, D. (100%), NASA Goddard Space Flight Center, “Missouri Space Grant Consortium,” $307,000, May 1, 2015 - April 30, 2016.

Rovey, J.

Rovey, J. (50%) and Yang, X. (50%), Air Force Research Lab, “Plasmonic Space Propulsion,” $157,395, August 15, 2014 - August 14, 2017.

Rovey, J. (50%) and Pernicka, H. (50%), University of Missouri System Interdisciplinary Intercampus Research Program, “Multi-mode Rocket for CubeSats,” $50,000, August 1, 2015 - July 31, 2016.

Rovey, J. (100%), NASA Goddard Space Flight Center, “Characterization of a Green Solid Electric Microthruster for Small Spacecraft,” $64,628, August 1, 2015 - July 31, 2016.

Pernicka, H. (80%) and Rovey, J. (20%),

Air Force Office of Scientific Research, “Development of a Validation of a Steroscopic Imager and a Micropropulsion System for Use in Spacecraft Close Proximity Operations,” $110,000, September 14, 2015 - September 14, 2016.

Rovey, J. (100%), NASA Marshall Space Flight Center, “Multi-Mode MicroPropulsion for Small Spacecraft,” $60,000, September 1, 2015 - August 31, 2016.

Bristow, D. (20%), DeMars, K. (7%), Kinzel, E. (7%), Landers, R. G. (15%), Leu, M. (7%), Park, J. (7%), Pernicka, H. (7%), Rovey, J. (16%) and Duan, L. (7%), US Department of Education, “GAANN: Doctoral Research and Training in Mechatronics,” $295,278, September 1, 2015 - August 31, 2016.

Stutts, D.

Pommerenke, D. (47%), Khilkevich, V. (48%) and Stutts, D. (5%), Huawei Technologies Company, “Development of a Passive Intermodulation Measurement System,” $90,000, August 4, 2015 - August 3, 2016.

Tsai, H.

Tsai, H. (60%) and Leu, M. (40%), Department of Energy, “Additive Manufacturing of Smart Parts with Embedded Sensors for In-Situ Monitoring in Advanced Energy Systems,” $250,000, October 1, 2013 – September 30, 2016.

Tsai, H. (100%), University of Missouri Research Board, “3D Printing for Amorphous Metal Structures,” $41,672, January 1 - December 31, 2016.

Wang, C.

Wang, C. (100%), University of Missouri Research Board, “Microbubble Acoustofluidics in Viscoelastic Fluids,” $44,724, July 1, 2015 - December 31, 2016.

Yang, X.

Rovey, J. (50%) and Yang, X. (50%), Air Force Research Laboratory, “Plasmonic Space Propulsion,” $157,395, August 15, 2014 - August 14, 2017.

Yang, X. (100%), 3M, “Controlling The Flow of Light With Metamaterial Nanostructures,” $15,000, June 1, 2015 - May 31, 2019.

Yang, X. (100%), Army Research Office, “Enhancement of Light Trapping and Optical Absorption in Complex ZnO Nanostructures,” $50,000, September 1, 2015 - May 31, 2016.

Yucelen, T.

Yucelen, T. (100%), Oak Ridge Associated University, “Autonomous Multivehicle Systems for Real-Time Situational Awareness in Adverse Environments,” $5000, June 1, 2015 - May 31, 2016.

Yucelen, T. (60%) and Balakrishnan, S. (40%), Wichita State University, “Active Wing Shaping Control of Morphing Aircraft,” $270,000, August 1, 2015 - July 31, 2018.


Birman, V.

Session Chairman, Instability of Solids, Structures and Fluids, ASME International Mechanical Engineering Congress and Exposition (IMECE 2016), Phoenix, AZ, November 16, 2016.

DeMars, K.

Session Chair, 26th AAS/AIAA Space Flight Mechanics Meeting, Napa, CA, February 14 - 18, 2016.Organizer and Chair, Special Session on Space Object Detection, Tracking, Identification, and Classification, 19th International Conference on Information Fusion, Heidelberg, Germany, July 2016.

Session Chair, 2016 AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA, September 2016.

Duan, L.

Session Chair, 46th AIAA Fluid Dynamics Conference, Washington, DC, June 2016.

Isaac, K.

Co-Chair, Fundamentals and Applications of Microfluidic and Nanofluidic Devices, PRiME: Joint International Meeting of Electrochemical Society of Japan, Electrochemical Society and Korean Electrochemical Society, Honolulu, Hawaii, October 2 - 7, 2016.

Kinzel, E.

Session Chair, “Physical Modeling II: Modeling for Metals II,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Landers, R. G.

Program Chair, 2016 International Symposium on Flexible Automation, Cleveland, OH, August 1 - 3, 2016.

Session Chair, 2016 ASME Dynamic Systems and Control Conference, Minneapolis, MN, October 11 - 13, 2016.

Leu, M.

Co-Chair, NSF CAREER Proposal Writing Workshop, St. Louis, MO, March 21 - 22, 2016.

Liou, F.

Session Chair, “Additive Manufacturing: Building the Pathway Towards Process and Material Qualification — Qualification of Novel Materials,” 145th TMS Annual Meeting & Exhibition, Nashville, TN, February 16 - 18, 2016.

Session Chair, “Materials III: Ti-6Al-4V,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 7 - 10, 2016.

Rovey, J.

Electric Propulsion Technical Area Organizer, Propulsion and Energy 2016

Wang, C.

Co-Chair, Technical Track -- Optofluidics, Acoustic Fluidics, and Magnetic Fluidics, International Conference of Microfluidics,

Nanofluidics and Lab-on-a-Chip, Dalian, China, June 10 - 12, 2016.

Wojnar, C.

Symposium Organizer, Society of Engineering Science Conference, College Park, MD, October 2 - 5, 2016.

Session Chair, Society of Engineering Science Conference, College Park, MD, October 2 - 5, 2016.

Birman, V.

ASME Congress Steering Committee, 2016.

ASME Aerospace Division Executive Committee, September 28, 2016.

ASME Aerospace Division Executive Committee, November 2016.

ASME Aerospace Division Structures and Materials Technical Committee, November 2016.

Bristow, D.

Member, ASME Technical Program Committee, 2016 American Controls Conference, July 6 - 8, 2016.

Member, Technical Program Committee, 2016 International Symposium on Flexible Automation, August 1 - 3, 2016.

Member, Technical Program Committee, 2016 ASME Dynamic Systems and Control Conference, October 12 - 14, 2016.

DeMars, K.

Member, AIAA Astrodynamics Technical Committee, 2016.

Du, X.

Review Coordinator, 13th ASME International Conference on Design Education, 2016.

Review Coordinator, 42nd ASME Design Automation Conference, 2016.

Hosder, S.

Membership Subcommittee Chair, AIAA Hypersonic Technologies and Aerospace Planes (HyTASP) 2016 Program Committee Meeting, 54th AIAA Science and Technology Forum and Exposition 2016, San Diego, CA, January 4 - 8, 2016.

Member, Editor in Chief Selection Committee, AIAA Journal of Spacecraft and Rockets, December 2016.

Kinzel, E.

Advisory Board, Columbia Area Career Center, Laser/Optics Program, 2016.

Koylu, U.

ASME K-2 Committee on Long Range Directions & Issues in Heat Transfer, 2016.

Landers, R. G.

Secretary, ASME Dynamic Systems and Control Division, 2016.

Executive Committee Member, ASME Dynamic Systems and Control Division, 2016.

Executive Committee Member, Digital Manufacturing Design Innovation Institute, September 2016.

Rovey, J.

Technical Area Organizer, Electric Propulsion Technical Committee, AIAA Propulsion and Energy Forum, Salt Lake

City, UT, July 25 - 27, 2016.

Wojnar, C.

Inverse Problem Methodologies Technical Division Meeting, Society of Experimental Mechanics, Orlando, FL, June 2016.

ASME Materials Division, Technical Committee, Multifunctional Materials, 2016.

ASME Applied Mechanics Division, Technical Committee on Fracture and Failure Mechanics, 2016.

ASME Applied Mechanics Division, Materials Division, Joint Technical Committee, Constitutive Equations, 2016.

ASME Applied Mechanics Division, Technical Committee, Composite Materials, 2016.

ASME Applied Mechanics Division, Technical Committee, Experimental Mechanics Committee, 2016.

Yucelen, T.

Student Paper Competition Chair, AIAA Infotech@Aerospace Conference, San Diego, CA, January 4 - 8, 2016.

Birman, V.

Associate Editor, Journal Composites Theory and Practice, Polish Society for Composite Materials Associate Editor, Composites Part B: Engineering

Associate Editor, Editorial Board, International Journal of Aeronautical and Space Sciences, Korean Society for Aeronautical and Space Sciences

Bristow, D.

Associate Editor, ASME Journal of Dynamic Systems, Measurement, and Control

Crosbie, A.

Associate Editor, Journal of Quantitative Spectroscopy & Radiative Transfer

Du, X.

Associate Editor, ASME Journal of Mechanical Design Review Editor, Structural and Multidisciplinary Optimization

Guest Editor, Artificial Intelligence for Engineering Design, Analysis and Manufacturing

Gao, J.

Member, Editorial Board, Scientific Reports

Koylu, U.

Assistant Editor, International Journal of Hydrogen Energy

SERVICE ON COMMITTEES OF PROFESSIONAL ORGANIZATIONS

EDITORS OF SYMPOSIUMS, PROCEEDINGS AND JOURNALS

CHAIRMAN, CO-CHAIRMAN OF TECHNICAL SESSIONS AND SYMPOSIUMS

PROFESSIONAL & SCHOLARLY ACTIVITIES


Landers, R. G.

Associate Editor, Journal of the Korean Society of Manufacturing Technology Engineers

Leu, M.

Editorial Board, Journal of Virtual and Physical Prototyping

Park, J.

Lead Guest Editor, Journal of Chemistry

Yucelen, T.

Associate Editor, IFAC Symposium on Advances in Control Education, Bratislava, Slovak Republic, June 1 - 3, 2016.

Balakrishnan, S.

Seung-Lark Lim, S., Bradley, J., Cherry, C., Davis, A., Balakrishnan, S., Ha, O., Bruce, J. and Bruce, A., “The Child’s Brain Computes and Utilizes Internalized Maternal Choices,” Nature Communications, Issue 7, pp. 1 - 10, May 24, 2016.

Birman, V.

Tuwair, H., Volz, J., ElGawady, M. A., Mohamed, M., Chandrashekhara, K. and Birman, V., “Testing and Evaluation of Polyurethane-Based GFRP Sandwich Bridge Deck Panels with Polyurethane Foam Core,” ASCE Journal of Bridge Engineering, Vol. 21, Issue 1, pp. 04015033-1 - 04015033-13, January 2016.

Tuwair, H., Volz, J., ElGawady, M., Mohamed, M., Chandrashekhara, K. and Birman, V., “Behavior of GFRP Bridge Deck Panels Infilled with Polyurethane Foam Under Various Environmental Exposure,” Structures, Vol. 5, pp. 141 - 151, February 2016.

Tuwair, H., Volz, J., ElGawady, M., Chandrashekhara, K. and Birman, V., “Modeling and Analysis of GFRP Bridge Deck Panels Filled with Polyurethane Foam,” ASCE Journal of Bridge Engineering, Vol. 21, No. 5, pp. 04016012-1 - 04016012-14, May 2016.

Saadat, F., Deymier, A. C., Birman, V., Thomopoulos, S. and Genin, G. M., “The Concentration of Stress at the Rotator Cuff Tendon-to-Bone Attachment Site is Conserved Across Species,” Journal of the Mechanical Behavior of Biomedical Materials, Vol. 62, pp. 24 - 32, September 2016.

Chandrashekhara, K.

Bheemreddy, V., Chandrashekhara, K., Dharani, L. R. and Hilmas, G.E., “Microstructure Image-Based Modeling of Fracture in Continuous Fiber-Reinforced Ceramic Matrix Composites,” Journal of Multifunctional Composites, Vol. 3, Issue 1, pp. 1 - 9, January 2016.

Tuwair, H., Volz, J., ElGawady, M.A., Mohamed, M., Chandrashekhara, K. and Birman, V., “Testing and Evaluation of Polyurethane-Based GFRP Sandwich Bridge Deck Panels with Polyurethane Foam Core,” ASCE Journal of Bridge Engineering, Vol. 21, No. 1, pp. 04015033-1 - 04015033-13, February 2016.

Tuwair, H., Volz, J., ElGawady, M. A., Mohamed, M., Chandrashekhara, K. and Birman, V.,

“Behavior of GFRP Bridge Deck Panels Infilled with Polyurethane Foam Under Various Environmental Exposure,” Structures, Vol. 5, pp. 141 - 151, January 2016.

Kaur, A., Anandan, S., Yuan, L., Watkins, S. E., Chandrashekhara, K., Xiao, H. and Phan, N., “Strain Monitoring of Bismaleimide Composites Using Embedded Microcavity Sensor,” SPIE Optical Engineering, Vol. 53, No. 3, pp. 037102-1 - 037102-6, March 2016.

Huo, Z., Mohamed, M., Nicholas, J. R., Wang, X. and Chandrashekhara, K., “Experimentation and Simulation of Moisture Diffusion in Foam-Cored Polyurethane Sandwich Structure,” Journal of Sandwich Structures and Materials, Vol. 18, No. 1, pp. 30 - 49, 2016.

Bheemreddy, V., Huo, Z., Chandrashekhara, K. and Brack, R. A., “Modeling and Simulation of Cure Kinetics and Flow in Cavity-Molded Composites,” Journal of the American Helicopter Society, Vol. 61, pp. 022004-1 - 022004-10, April 2016.

Tuwair, H., Volz, J., ElGawady, M. A., Chandrashekhara, K. and Birman, V., “Modeling and Analysis of GFRP Bridge Deck Panels Filled with Polyurethane Foam,” ASCE Journal of Bridge Engineering, Vol. 21, No. 5, pp. 04016012-1 - 04016012-14, May 2016.

Anandan, S., Dhaliwal, G. S., Chandrashekhara, K., Berkel, T. R. and Pfitzinger, D., “Processing and Performance of Out-of-Autoclave Bismaleimide Composite Sandwich Structures,” SAMPE Journal, Vol. 52, No. 3, pp. 44 - 53, May/June 2016.

Nicholas, J., Mohaned, M., Dhaliwal, G. S., Anandan, S. and Chandrashekhara, K., “Effects of Accelerated Environmental Aging on Fiber Glass Reinforced Thermoset Polyurethane Composites,” Composites Part B, Vol. 94, pp. 370 - 378, June 2016.

Hussein, R. M., Anandan, S. and Chandrashekhara, K., “Anisotropic Oxidation Prediction Using Optimized Weight Loss Behavior of Bismaleimide Composites,” Journal of Materials Science, Vol. 51, Issue 15, pp. 7236 - 7253, August 2016.

Bheemreddy, V., Chandrashekhara, K., Dharani, L. R. and Hilmas, G. E., “Computational Study of Micromechanical Damage Behavior in Continuous Fiber-Reinforced Ceramic Composites,” Journal of Materials Science, Vol. 51, pp. 8610 - 8624, September 2016.

Anandan, S., Dhaliwal, G. S., Samaranayake, V. A., Chandrashekhara, K., Berkel, T. R. and Pfitzinger, D., “Influence of Cure Conditions on Out-of-Autoclave Bismaleimide Composite Laminates,” Journal of Applied Polymer Science, Vol. 133, pp. 43984 - 43991, October 2016.

Wang, X., Chandrashekhara, K., Rummel, S. A., Lekakh, S., Van Aken, D. C. and O’Malley, R. J., “Modeling of Mass Flow Behavior of Hot Rolled Low Alloy Steel Based on Combined Johnson-Cook and Zerilli-Armstrong Model,” Journal of Materials Science, Vol. 52, pp. 2800 - 2815, November 2016.

Mohamed, M., Hussein, R., Abutunis, A., Huo, Z., Chandrashekhara, K. and Sneed, L. H., “Manufacturing and Evaluation of

Polyurethane Composite Structural Insulated Panels,” Journal of Sandwich Structures and Materials, Vol. 18, pp. 769 - 789, November 2016.

Chen, L.

Cao, C., Chen, L. Y., Xu, J., Zhao, J. Z., Pozuelo, M. and Li, X. C., “Phase Control in Immiscible Zn-Bi Alloy by Tungsten Nanoparticles,” Materials Letters, Vol. 174, pp. 213 - 216, July 2016.

Crosbie, A.

Mueller, D. W. and Crosbie, A. L., “Backscattered Stokes Parameters from Semi-Infinite Rayleigh Scattering Media Exposed to a Laser,” AIAA Journal of Thermophysics and Heat Transfer, Vol. 31, No. 2, pp. 336 - 377, October 2016.

DeMars, K.

Darling, J. E. and DeMars, K. J., “Uncertainty Propagation of Correlated Quaternion and Euclidean States Using the Gauss-Bingham Density,” Journal of Advances in Information Fusion, Vol. 11, No. 2, December 2016.

Dharani, L.

Bheemreddy, V., Chandrashekhara, K., Dharani, L. R. and Hilmas, G. E., “Microstructure Image-Based Modeling of Fracture in Continuous Fiber-Reinforced Ceramic Matrix Composites,” Journal of Multifunctional Composites, Vol. 3, Issue 1, pp. 1 - 9, January 2016.

Bheemreddy, V., Chandrashekhara, K., Dharani, L. R. and Hilmas, G. E., “Computational Study of Micromechanical Damage Behavior in Continuous Fiber-Reinforced Ceramic Composites,” Journal of Materials Science, Vol. 51, pp. 8610 - 8624, September 2016.

Du, X.

Xu, M., Du, X., Qiu, Z. and Wang, C., “Epistemic Uncertainty Propagation in Energy Flows Between Structural Vibrating Systems,” Journal of Sound and Vibration, Vol. 366, pp. 372 - 395, March 2016.

Cheng, Y. and Du, X., “System Reliability Analysis With Dependent Component Failures During Early Design Stage - A Feasibility Study,” ASME Journal of Mechanical Design, Vol. 138, pp. 051405-1 – 051405-12, May 2016.

Hu, Z. and Du, X., “Reliability-Based Design Optimization Under Stationary Stochastic Process Loads,” Engineering Optimization, Vol. 48, pp. 1296 - 1312, August 2016.

Xie, S., Pan, B. and Du, X., “An Efficient Hybrid Reliability Analysis Method with Random and Interval Variables,” Engineering Optimization, Vol. 48, pp. 1459 - 1473, September 2016.

Hu, Z., Mahadevan, S. and Du, X., “Uncertainty Quantification of Time-Dependent Reliability Analysis in the Presence of Parametric Uncertainty,” ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part B, Mechanical Engineering, Vol. 2, pp. 031001-1 - 031001-9, September 2016.

Zhu, Z. and Du, X., “Reliability Analysis with Monte Carlo Simulation and Dependent Kriging Predictions,” ASME Journal of

JOURNAL PUBLICATIONS


Mechanical Design, Vol. 138, pp. 121403-1 - 121403-11, December 2016.

Duan, L.

Duan, L., Choudhari, M. M. and Zhang, C., “Pressure Fluctuations Induced by a Hypersonic Turbulent Boundary Layer,” Journal of Fluid Mechanics, Vol. 804, pp. 578 - 607, September 2016.

Li, F., Choudhari, M. M., Paredes-Gonzalez, P. and Duan, L., “High-Frequency Instabilities of Stationary Crossflow Vortices in a Hypersonic Boundary Layer,” Physical Review Fluids, Vol. 1, pp. 053603-1 - 053603-32, September 2016.

Eversman, W.

Eversman, W., “Broadband Noise Suppression for Turbofan Inlet Applications,” Aeroacoustics, Vol. 15, pp. 367 - 394, October 2016.

Gao, J.

Sun, L., Gao, J. and Yang, X., “Optical Nonlocality Induced Zitterbewegung Near the Dirac Point in Metal-Dielectric Multilayer Metamaterials,” Optics Express, Vol. 24, Issue 7, pp. 7055 - 7062, 2016.

Sun, L., Yang, X. and Gao, J., “Analysis of Nonlocal Effective Permittivity and Permeability in Symmetric Metal-Dielectric Multilayer Metamaterials,” Journal of Optics, Vol. 18, pp. 065101-1 - 065101-11, April 13, 2016.

Zeng, J., Li, L., Yang, X. and Gao, J., “Generating and Separating Twisted Light by Gradient-Rotation Split-Ring Antenna Metasurfaces,” Nano Letters, Vol. 16, pp. 3101 - 3108, April 19, 2016.

Wan, W., Yang, X. and Gao, J., “Strong Coupling Between Mid-Infrared Localized Plasmons and Phonons,” Optics Express, Vol. 24, Issue 11, pp. 12367 - 12374, May 27, 2016.

Li, Z., Wang, W., Rosenmann, D., Czaplewski, D., Yang, X. and Gao, J., “All-Metal Structural Color Printing Based on Aluminum Plasmonic Metasurfaces,” Optics Express, Vol. 24, pp. 20472 - 20480, September 5, 2016.

Wan, X., Gao, J. and Yang, X., “Full-Color Plasmonic Metasurface Holograms,” ACS Nano, Vol. 10, pp. 10671 - 10680, 2016.

Hosder, S.

West, T., Brune, A., Hosder, S. and Johnston, C., “Uncertainty Analysis of Radiative Heating Predictions for Titan Entry,” Journal of Thermophysics and Heat Transfer, Vol. 30, No. 2, pp. 438 - 451, April - June 2016.

Brune, A., Hosder, S. and Edquist, K., “Uncertainty Analysis of Fluid-Structure Interaction of a Deformable Hypersonic Inflatable Aerodynamic Decelerator,” Journal of Spacecraft and Rockets, Vol. 53, No. 4, pp. 654 - 668, July - August 2016.

Kinzel, E.

Ding, L., Qin, J., Guo, S., Liu, T., Kinzel, E. C. and Wang, L., “Resonant Effects in Nanoscale Bowtie Apertures,” Nature: Scientific Reports, Vol. 6, pp. 1 - 6, June 2, 2016.

Qu, C. and Kinzel, E. C., “Polycrystalline Metasurface Perfect Absorbers Fabricated Using Microsphere Photolithography,” Optics

Letters, Vol. 41, No. 15, pp. 3399 - 3402, August 1, 2016.

Koylu, U.

Vaz, W. S., Nandi, A. K. and Koylu, U. O., “A Multi-Objective Approach to Find Optimal Electric Vehicle Accelerations: Simultaneous Minimization of Acceleration Duration and Energy Consumption,” IEEE Transactions on Vehicular Technology, Vol. 65, pp. 4633 - 4644, June 6, 2016.

Karagoz, Y., Sandalci, T., Koylu, U. O., Dalkilic, A. S. and Wongwises, S., “Effect of the Use of Natural Gas-Diesel Fuel Mixture on Performance, Emissions and Combustion Characteristics of a Compression-Ignition Engine,” Advances in Mechanical Engineering, Vol. 8, pp. 1 - 13, August 3, 2016.

Jabbr, A. I., Vaz, W. S., Khariallah, H. A. and Koylu, U. O., “Multi-Objective Optimization of Operating Parameters for Hydrogen-Fueled Spark-Ignition Engines,” International Journal of Hydrogen Energy, Vol. 41, pp. 18291 - 18299, October 26, 2016.

Landers, R. G.

Fajri, P., Lotfi, N., Ferdowsi, M. and Landers, R. G., “Development of an Educational Small–Scale Hybrid Electric Vehicle (HEV) Setup,” IEEE Intelligent Transportation Systems Magazine, Vol. 8, No. 2, pp. 8 – 21, August 2016.

Lofti, N., Landers, R. G., Li, J. and Park, J., “Reduced-Order Electrochemical Model-Based SOC Observer With Output Model Uncertainty Estimation,” IEEE Transaction on Control Systems Technology, Issue 99, pp. 1 - 14, September 1, 2016.

Li, M., Ghazanfari, A., Li, W., Landers, R. G. and Leu, M. C., “Modeling and Analysis of Paste Freezing in Freeze–Form Extrusion Fabrication of Thin–Wall Parts via a Lumped Method,” Journal of Materials Processing Technology, Vol. 237, pp. 163 – 180, November 2016.

Lotfi, N., Zomorodi, H. and Landers, R. G., “Active Disturbance Rejection Control for Voltage Stabilization in Open-Cathode Fuel Cells through Temperature Regulation,” Control Engineering Practice, Vol. 56, pp. 92 – 100, November 2016.

Leu, M.

Li, M., Ghazanfari, A., Li, W., Landers, R. G. and Leu, M. C., “Modeling and Analysis of Paste Freezing in Freeze–Form Extrusion Fabrication of Thin–Wall Parts via a Lumped Method,” Journal of Materials Processing Technology, Vol. 237, pp. 163 – 180, November 2016.

Ghazanfari, A., Li, W., Leu, M. C., Zhuang, Y. and Huang, J., “Advanced Ceramic Components with Embedded Sapphire Optical Fiber Sensors for High Temperature Applications,” Materials and Design, Vol. 112, pp. 197 – 206, December 2016.

Liou, F.

Isanaka, S. P., Karnati, S. and Liou, F., “Blown Powder Deposition of 4047 Aluminum on 2024 Aluminum Substrates,” Manufacturing Letters, Vol. 7, pp. 11 - 14, January 2016.

Isanaka, S. P., Sparks, T. E., Liou, F. and Newkirk, J. W., “Design Strategy for Reducing Manufacturing and Assembly Complexity of Air-Breathing Proton Exchange Membrane Fuel Cells,” Journal of Manufacturing Systems, Vol. 38, pp. 165 - 171, January 2016.

Wang, Z., Liu, R., Sparks, T. and Liou, F., “Realization of Robot Ink Deposition on a Curved Surface,” International Journal of Computer Applications in Technology, Vol. 53, No. 2, pp. 183 – 188, 2016.

Isanaka, S., Liou, F. and Newkirk, J., “Nonprismatic Air-Breathing Fuel Cells—Concept, Theory, Design, and Manufacturing,” ASME Journal of Electrochemical Energy Conversion and Storage, Vol. 13, pp. 021006-1 – 021006-11, May 2016.

Gaja, H. and Liou, F., “Depth of Cut Monitoring for Hybrid Manufacturing Using Acoustic Emission Sensor,” The International Journal of Advanced Manufacturing Technology, Vol. 86, pp. 1 - 13, June 2016.

Romy, F., Newkirk, J. and Liou, F., “Investigation of Forged-Like Microstructure Produced by a Hybrid Manufacturing Process,” Rapid Prototyping Journal, Vol. 22, Issue 4, pp. 717 - 726, June 2016.

Zhang, J., Liou, F., Seufzer, W. and Taminger, K., “A Coupled Finite Element Cellular Automaton Model to Predict Thermal History and Grain Morphology of Ti-6Al-4V During Direct Metal Deposition (DMD),” Additive Manufacturing, Vol. 11, pp. 32 - 39, July 2016.

Gaja, H. and Liou, F., “Defects Monitoring of Laser Metal Deposition Using Acoustic Emission Sensor,” The International Journal of Advanced Manufacturing Technology, September 2016.

Yan, L., Chen, X., Li, W., Liou, F. and Newkirk, J., “Direct Laser Deposition of Ti-6Al-4V from Elemental Powder Blends,” Rapid Prototyping Journal, Vol. 22, Issue 5, pp. 810 - 816, September 2016.

Gaja, H. and Liou, F., “Automatic Detection of Depth of Cut During End Milling Operation Using Acoustic Emission Sensor,” The International Journal of Advanced Manufacturing Technology, Vol. 86, Issue 9, pp. 2913 – 2925, October 2016.

Yan, L., Li, W., Chen, X., Zhang, Y., Newkirk, J., Liou, F. and Dietrich, D., “Simulation of Cooling Rate Effects on Ti-48Al-2Cr-2Nb Crack Formation in Direct Laser Deposition,” The Member Journal of The Minerals, Metals & Materials Society, December 2016.

Meeks, W.

Meeks, W. C. and Rovey, J. L., “Time-Resolved Temperature in an Argon Theta-Pinch by Line Ratio Methods,” IEEE Transactions on Plasma Science, Vol. 44, No. 8, pp. 1411 - 1418, August 2016.

Okafor, A.

Okafor, A. C. and Sultan, A. A., “Development of a Mechanistic Cutting Force Model for Wavy-Edge Bull-Nose Helical End-Milling of Inconel 718 Under Emulsion Cooling Strategy,” Applied Mathematical Modelling, Vol. 40, Issue 4, pp. 2637 - 2660, February 15, 2016.


Sultan, A. and Okafor, A. C., “Effects of Geometric Parameters of Wavy-Edge Bull-Nose Helical End-Mill on Cutting Force Prediction in End-Milling of Inconel 718 Under MQL Cooling Strategy,” Journal of Manufacturing Processes, Vol. 23, pp. 102 - 114, August 2016.

Pan, H.

Tsai, S., Liu, Y., Pan, H., Liu, C. and Lee, M., “The Coupled Photothermal Reaction and Transport in a Laser Additive Metal Nanolayer Simultaneous Synthesis and Patterning for Flexible Electronics,” Nanomaterials, Vol. 6, Issue 1, pp. 1 - 14, January 8, 2016.

Ludwig, B., Zheng, Z., Shou, W., Wang, Y. and Pan, H., “Solvent-Free Manufacturing of Electrodes for Lithium-ion Batteries,” Scientific Reports, Vol. 6, pp. 1 - 10, March 17, 2016.

Shou, W. and Pan, H., “Direct Printing of Microstructures by Femtosecond Laser Excitation of Nanocrystals in Solution,” Appled Physics Letters, Vol. 108, No. 21, pp. 214101-1 – 214101-5, May 2016.

Shou, W. and Pan, H., “Silicon-Wall Interfacial Free Energies via Thermodynamics Integration,” Journal of Chemical Physics, Vol. 145, pp. 184702-1 - 184702-11, November 2016.

Yu, X., Mahajan, B., Shou, W. and Pan, H., “Materials, Mechanics, and Patterning Techniques for Elastomer-Based Stretchable Conductors,” Micromachines, Vol. 8, pp. 1 - 29, December 2016.

Park, J.

Park, J., Li, J., Lu, W. and Sastry, A. M., “Geometric Consideration of Nanostructures for Energy Storage Systems,” Journal of Applied Physics, Vol. 119, Issue 2, pp. 025101-1 - 025101-7, January 14, 2016.

Lee, S., Sastry, A. M. and Park, J., “Study on Microstructures of Electrodes in Lithium-Ion Batteries Using Variational Multi-Scale Enrichment,” Journal of Power Sources, Vol. 315, pp. 111 - 119, May 2016.

Lee, Y., Park, J. and Lu, W., “Electronic and Bonding Properties of LiMn2O4 Spinel with Different Surface Orientations and Doping Elements and Their Effects on Manganese Dissolution,” Journal of the Electrochemical Society, Vol. 163, pp. A1359 - A1368, April 26, 2016.

Lofti, N., Landers, R. G., Li, J. and Park, J., “Reduced-Order Electrochemical Model-Based SOC Observer With Output Model Uncertainty Estimation,” IEEE Transaction on Control Systems Technology, Issue 99, pp. 1 - 14, September 1, 2016.

Park, J., Patel, R. L. and Liang, X., “Ionic and Electronic Conductivities of Atomic Layer Deposition Thin Film Coated Lithium Ion Battery Cathod Particles,” The Royal Society of Chemistry, Vol. 6, pp. 98768 - 98776, October 2016.

Rovey, J.

Meeks, W. C. and Rovey, J. L., “Time-Resolved Temperature in An Argon Theta-Pinch by Line Ratio Methods,” IEEE Transactions on Plasma Science, Vol. 44, No. 8, pp. 1411 - 1418,

August 2016.

Maser, J. N., Ling, L., Deng, H., Yang, X. and Rovey, J. L., “Transmission Spectrum of Asymmetric Nanostructures for Plasmonic Space Propulsion,” Journal of Spacecraft and Rockets, Vol. 53, No. 5, pp. 998 - 1000, September – October 2016.

Stutts, D.

Dushaishi, M. F. A., Nygaard, R. and Stutts, D. S., “Effect of Drilling Fluid Hydraulics on Drill Stem Vibrations,” Journal of Natural Gas Science and Engineering, Vol. 35, Part A, pp. 1059 - 1069, September 2016.

Tsai, H.

Chen, C., Shen, Y. and Tsai, H. L., “A Foil-Based Additive Manufacturing Technology for Metal Parts,” ASME Journal of Manufacturing Science and Engineering, Vol. 139, pp. 024501-1 - 024501-6, August 2016.

Shen, Y., Li, Y., Chen, C. and Tsai, H. L., “3D Printing of Large, Complex Metallic Glass Structures,” Materials and Design, Vol. 117, pp. 213 - 222, December 2016.

Wang, C.

Zhou, R. and Wang, C., “Microfluidic Separation of Magnetic Particles with Soft Magnetic Microstructures,” Microfluidics and Nanofluidics, Vol. 20, Issue 3, Article 48, March 2016.

Zhou, R. and Wang, C., “Multiphase Ferrofluid Flows for Micro-Particle Focusing and Separation,” Biomicrofluidics, Vol. 10, pp. 034101-1 - 034101-17, May 5, 2016.

Zhou, R., Yang, Q., Bai, F., Werner, J., Shi, H., Ma, Y. and Wang, C., “Fabrication and Integration of Microscale Permanent Magnets for Particle Separation in Microfluidics,” Microfluidics and Nanofluidics, Vol. 20, Issue 7, pp. 1 - 12, July 12, 2016.

Yang, X.

Sun, L., Gao, J. and Yang, X., “Optical Nonlocality Induced Zitterbewegung Near the Dirac Point in Metal-Dielectric Multilayer Metamaterials,” Optics Express, Vol. 24, Issue 7, pp. 7055 - 7062, 2016.

Zeng, J., Li, L., Yang, X. and Gao, J., “Generating and Separating Twisted Light by Gradient-Rotation Split-Ring Antenna Metasurfaces,” Nano Letters, Vol. 16, pp. 3101 - 3108, April 19, 2016.

Sun, L., Yang, X. and Gao, J., “Analysis of Nonlocal Effective Permittivity and Permeability in Symmetric Metal-Dielectric Multilayer Metamaterials,” Journal of Optics, Vol. 18, pp. 065101-1 - 065101-11, April 13, 2016.

Wan, W., Yang, X. and Gao, J., “Strong Coupling Between Mid-Infrared Localized Plasmons and Phonons,” Optics Express, Vol. 24, Issue 11, pp. 12367 - 12374, May 27, 2016.

Li, Z., Wang, W., Rosenmann, D., Czaplewski, D., Yang, X. and Gao, J., “All-Metal Structural Color Printing Based on Aluminum Plasmonic Metasurfaces,” Optics Express, Vol. 24, pp. 20472 - 20480, September 5, 2016.

Maser, J. N., Ling, L., Deng, H., Yang, X. and Rovey, J. L., “Transmission Spectrum of

Asymmetric Nanostructures for Plasmonic Space Propulsion,” Journal of Spacecraft and Rockets, Vol. 53, No. 5, pp. 998 - 1000, September – October 2016.

Wan, X., Gao, J. and Yang, X., “Full-Color Plasmonic Metasurface Holograms,” ACS Nano, Vol. 10, pp. 10671 - 10680, 2016.

Yucelen, T.

Yucelen, T., “Distributed Control of Active-Passive Networked Multiagent Systems,” IEEE Transactions on Control of Network Systems, Vol. PP, Issue 99, pp. 1 - 8, March 22, 2016.

Yucelen, T. and Sanyal, A., “Decentralized Consensus Control of a Rigid-Body Spacecraft Formation with Communication Delay,” Journal of Guidance, Control, and Dynamics, Vol. 39, No. 4, April 2016.

Balakrishnan, S.

Balakrishnan, S. N., Rajagopal, K. and Busemeyer, J., “Optimal Controller Design for Control-Affine Stochastic Systems Using Neural Networks and Path Integrals,” American Control Conference, Boston, MA, July 6 - 8, 2016.

Balakrishnan, S. and Rajagopal, K., “Intelligent Switching Between Multiple Model-Based Adaptive Controllers Using Data-Driven Control Theory,” American Control Conference, Boston, MA, July 6 - 8, 2016.

Balakrishnan, S. N., Xing, Y., Wang, X. and Miao, Z., “Optimal Impulse Control for Cow Parturient Paresis Treatment Design,” 14th Internatioal Conference on Control, Automation, Robotics and Vision, Phuket, Thailand, November 13 - 15, 2016.

Birman, V.

Linderman, S. W., Kormpakis, I., Gelberman, R. H., Birman, V., Wegst, U. G. K., Genin, G. M. and Thomopoulos, S., “Adhesive Sutures,” Paper No. 67522, ASME International Mechanical Engineering Congress and Exposition (IMECE 2016), Phoenix, AZ, November 11 - 17, 2016.

Bristow, D.

Luo, J., Gilbert, L., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Additive Manufacturing of Glass for Optical Applications,” SPIE Photonics West 2016, Paper No. 9738–28, San Francisco, CA, February 13 - 18, 2016.

Pribe, J. D., West, B. M., Gegel, M. L., Hartwig, T., Lunn, T., Brown, B., Bristow, D. A., Landers, R. G. and Kinzel, E. C., “Modal Response as a Validation Technique for Metal Parts Fabricated with Selective Laser Melting,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Ma, L., Bazzoli, P., Sammons, P. M., Bristow, D. A. and Landers, R. G., “Modeling and Compensation of Joint–Dependent Kinematic Errors in Robotic Manipulators,” International Symposium on Flexible Automation, Cleveland, OH, August 1 – 3, 2016.

REFEREED CONFERENCE PAPERSAND PROCEEDINGS


Sammons, P. M., Bristow, D. A. and Landers, R. G., “Frequency Domain Uncertainty Modeling and Quantification of the Laser Metal Deposition Process,” Dynamic Systems and Control Conference, Paper No. DSCC2016-9777, Minneapolis, MN, October 12 – 14, 2016.

Chandrashekhara, K.

Motaparti, K. P., Taylor, G. A., Leu, M. C., Chandrashekhara, K., Castle, J. and Matlack, M., “Effects of Build Parameters on Compression Properties for ULTEM 9085 Parts by Fused Deposition Modeling,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Meng, S., Mason, L., Wang, X., Taylor, G., Leu, M., Chandrashekhara, K., Castle, J. and Matlack, M., “Effect of Sparse-Build Internal Structure on Performance of Fused Deposition Modeling Tools,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Taylor, G., Wang, X., Mason, L., Leu, M. C. and Chandrashekhara, K., “Investigation of Ultem 1010 FDM Sparse-Build Parts Using Design of Experiments and Numerical Simulation,” Paper No. TP16-0151, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Hussein, R. M., Anandan, S., Dhaliwal, G. S. and Chandrashekhara, K., “Flexural Behavior of Cross-Ply Thermally Aged Bismaleimide Composites,” Paper No. TP16-0155, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Huo, Z., Taylor, G. and Chandrashekhara, K., “Numerical Simulation of a Multilayer Transparent Composite Panel Under Impact,” Paper No. TP16-0157, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Dhaliwal, G. S., Anandan, S., Chandrashekhara, K., Dudenhoeffer, N. and Nam, P., “Fabrication and Testing of Soy-Based Polyurethane Foam,” Paper No. TP16-0148, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Anandan, S., Dhaliwal, G. S., Chandrashekhara, K., Berkel, T. R. and Castle, J., “Progressive Damage Modeling of Sandwich Composites Under Edgewise Compression,” Paper No. TP16-0149, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Meinders, R., Nicholas, J., Taylor, G. and Chandrashekhara, K., “Evaluation of Continuous Fiber–Reinforced Ceramic Composites Fabricated Using High Pressure Resin Transfer Molding,” Paper No. TP16-0150, Composites and Advanced Materials Expo (CAMX) Conference, Anaheim, CA, September 26 - 29, 2016.

Spratt, M., Newkirk, J. W. and Chandrashekhara, K., “Fabrication of Metal Matrix Syntactic Foams by a Laser Additive Manufacturing Process,” Materials Science and Technology Conference, Salt Lake City, UT, October 23 - 27, 2016.

DeMars, K.

Crain, T., Bishop, R., Carson, J., Trawny, N., Hanak, C., Sullivan, J., Christian, J., DeMars, K., Campbell, T. and Getchius, J., “Approach-Phase Precision Landing with Hazard Relative Navigation: Terrestrial Test Campaign Results of the Morpheus/ALHAT Project,” AIAA Guidance, Navigation, and Control Conference, Paper No. AIAA 2016-0099, San Diego, CA, January 2016.

Bishop, R., Crain, T., Hanak, C., DeMars, K., Carson, J., Trawny, N. and Christian, J., “An Inertial Dual-State State Estimator for Precision Planetary Landing with Hazard Detection and Avoidance,” AIAA Guidance, Navigation, and Control Conference, Paper No. AIAA 2016-0098, San Diego, CA, January 2016.

Darling, J. E., LeGrand, K. A., Galchenko, P., Pernicka, H. J., DeMars, K. J., Shirley, A., McCabe, J., Schmid, C., Haberberger, S. J. and Mundahl, A. J., “Development and Flight of a Stereoscopic Imager for Use in Spacecraft Close Proximity Operations,” 39th AAS Guidance and Control Conference, Paper No. AAS 16-085, Breckenridge, CO, February 2016.

McCabe, J. S. and DeMars, K. J., “The Gaussian Mixture Consider Kalman Filter,” AAS/AIAA Space Flight Mechanics Meeting, Paper No. AAS 16-402, Napa, CA, February 14 - 18, 2016.

Haberberger, S. J. and DeMars, K. J., “Spacecraft Navigation Using a Robust Multi-Sensor Fault Detection Scheme,” AAS/AIAA Space Flight Mechanics Meeting, Paper No. AAS 16-445, Napa, CA, February 14 - 18, 2016.

McCabe, J. S. and DeMars, K. J., “Considering Uncertain System Parameters in Multitarget Space Surveillance Tracking,” 19th International Conference on Information Fusion, Heidelberg, Germany, July 2016.

Darling, J. E. and DeMars, K. J., “Uncertainty Propagation of Correlated Quaternion and Euclidean States Using Gauss-Bingham Mixtures,” 19th International Conference on Information Fusion, Heidelberg, Germany, July 2016.

Gualdoni, M. J., McCabe, J. S. and DeMars, K. J., “Set Joint Probabilistic Data Association for Relative Space Object Tracking,” Paper AIAA 2016-5200, 2016 AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA, September 2016.

McCabe, J. S. and DeMars, K. J., “Feature-Based Robotic Mapping with Generalized Multi-Bernoulli Filters for Planetary Landers,” Paper AIAA 2016-5565, 2016 AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA, September 2016.

Darling, J. E. and DeMars, K. J., “The Bingham-Gauss Mixture Filter for Pose Estimation,” Paper AIAA 2016-5631, 2016 AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA, September 2016.

Darling, J. E., Houtz, N., Frueh, C. and DeMars, K. J., “Recursive Filtering of Star Tracker Data,” Paper AIAA 2016-5672, 2016 AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA, September 2016.

Du, X.

Hu, Z. and Du, X., “A Physics-Based Reliability Method for Components Adopted in New Series Systems,” 2016 Annual Reliability and Maintainability Symposium, Tucson, AZ, January 25 - 28, 2016.

Du, X. and Zhang, J., “Optimization Design Under Time-Dependent Uncertainty,” 2016 2nd International Conference on Mechanical, Electronic and Information Technology Engineering, Chongqing, China, May 21 - 22, 2016.

Cheng, Y. and Du, X., “Reduction of System Reliability Model Uncertainty by Considering Dependent Components with Stochastic Process Loading,” ASME 2016 International Design Engineering Technical Conference and Computers and Information in Engineering Conference, IDETC 2016, Charlotte, NC, August 21 - 24, 2016.

Du, X., “Uncertainty Topics for Engineering Design Courses,” ASME 2016 International Design Engineering Technical Conference and Computers and Information in Engineering Conference, IDETC 2016, Charlotte, NC, August 21 - 24, 2016.

Zhu, Z. and Du, X., “A System Reliability Method with Dependent Kriging Predictions,” ASME 2016 International Design Engineering Technical Conference and Computers and Information in Engineering Conference, IDETC 2016, Charlotte, NC, August 21 - 24, 2016.

Hu, Z. and Du, X., “A Random Field Method for Time-Dependent Reliability Analysis with Random and Interval Variables,” ASME 2016 International Design Engineering Technical Conference and Computers and Information in Engineering Conference, IDETC 2016, Charlotte, NC, August 21 - 24, 2016.

Duan, L.

Zhang, C., Duan, L. and Choudhari, M. M., “Acoustic Radiation from a Mach 14 Turbulent Boundary Layer,” AIAA Aerospace Sciences and Technology Forum and Exposition, Paper No. AIAA 2016-0048, San Diego, CA, January 2016.

Li, F., Choudhari, M. M. and Duan, L., “Stationary Crossflow Breakdown due to Mixed Mode Spectra of Secondary Instabilities,” 46th AIAA Fluid Dynamics Conference, Paper No. AIAA-2016-3789, Washington, DC, June 2016.

Huang, J., Zhang, C. and Duan, L., “Turbulent Inflow Generation for Direct Simulations of Hypersonic Turbulent Boundary Layers and their Freestream Acoustic Radiation,” 46th AIAA Fluid Dynamics Conference, Paper No. AIAA-2016-3639, Washington, DC, June 2016.

Zhang, C. and Duan, L., “Multivariate Statistics Analysis of the Pressure Field Induced by High-Speed Turbulent Boundary Layers,” 46th AIAA Fluid Dynamics Conference, Paper No. AIAA2016-3190, Washington, DC, June 2016.

Eversman, W.

Eversman, W., “A Statistical Approach to Broadband Noise Suppression,” AIAA Aeroacoustics Conference, Paper No. AIAA 2016-2921, Lyon, France, May 30

- June 1, 2016.


Gao, J.

Li, C., Yang, X. and Gao, J., “Optical Force in Split Ring Resonator,” 10th Annual ISC Graduate Research Symposium, Rolla, MO, April 29, 2016.

Hosder, S.

West, T., Johnston, C. and Hosder, S., “Uncertainty and Sensitivity Analysis of Afterbody Radiative Heating Predictions for Earth Entry,” 54th AIAA Aerospace Sciences Meeting, AIAA Science and Technology Forum and Exposition 2016, Paper No. AIAA 2016-0738, San Diego, CA, January 4 - 8, 2016.

Schaefer, J., Hosder, S., Mani, M., Cary, A. and Krakos, J., “The Effect of Grid Topology and Flow Solver on Turbulence Model Closure Coefficient Uncertainties for a Transonic Airfoil,” 46th AIAA Fluid Dynamics Conference, Paper No. AIAA 2016-4400, Washington, DC, June 2016.

Brune, A., Hosder, S., Edquist, K. and Tobin, S., “Uncertainty Analysis of Thermal Protection System Response of a Hypersonic Inflatable Aerodynamic Decelerator,” 46th AIAA Thermophysics Conference, Paper No. AIAA-2016-3535, Washington, DC, June 2016.

Kinzel, E.


Pribe, J. D., West, B. M., Gegel, M. L., Hartwig, T., Lunn, T., Brown, B., Bristow, D. A., Landers, R. G. and Kinzel, E. C., “Modal Response as a Validation Technique for Metal Parts Fabricated with Selective Laser Melting,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Hostetler, J., Bender, T., Goldstein, J., Urbas, A., Gutierrez, R., Wojnar, C. and Kinzel, E., “Selective Laser Sintering of Low Density, Low Coefficient of Thermal Expansion Silica Parts,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Koylu, U.

Koylu, U., Farhangi, H., Konur, D., Warren, S. and Vaz, S., “A Realistic Driving Profile Optimization for Electric Vehicles,” 2016 Industrial and Systems Engineering Research Conference, Anaheim, CA, May 21 - 24, 2016.

Landers, R. G.


Zomorodi Moghadam, H. and Landers, R. G., “Extrusion Based Additive Manufacturing Using Explicit Model Predictive Control,” American Control Conference, Boston, MA, July 6 - 8, 2016.

Pribe, J. D., West, B. M., Gegel, M. L., Hartwig, T., Lunn, T., Brown, B., Bristow, D. A., Landers,

R. G. and Kinzel, E. C., “Modal Response as a Validation Technique for Metal Parts Fabricated with Selective Laser Melting,” 27th Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 – 10, 2016.

Ma, L., Bazzoli, P., Sammons, P. M., Bristow, D. A. and Landers, R. G., “Modeling and Compensation of Joint–Dependent Kinematic Errors in Robotic Manipulators,” International Symposium on Flexible Automation, Cleveland, OH, August 1 – 3, 2016.

Tang, A., Fan, Y., Li, S. and Landers, R. G., “Experimental and Numerical Studies of Wire Vibrations in Bonded Abrasive Wire Saw Processing,” International Symposium on Flexible Automation, Cleveland, OH, August 1 – 3, 2016.

Li, S., Wang, J., Tang, A. and Landers, R. G., “Force Modeling of Silicon Monocrystal Wire Saw Processing,” International Symposium on Flexible Automation, Cleveland, OH, August 1 – 3, 2016.

Sammons, P. M., Bristow, D. A. and Landers, R. G., “Frequency Domain Uncertainty Modeling and Quantification of the Laser Metal Deposition Process,” Dynamic Systems and Control Conference, Paper No. DSCC2016-9777, Minneapolis, MN, October 12 – 14, 2016.

Leu, M.

Meng, S., Mason, L., Taylor, G., Wang, X., Leu, M. C., Chandrashekhara, K., Matlack, M. and Castle, J., “Effect of Sparse-Build Internal Structure on Performance of Fused Deposition Modeling Tools Under Pressure,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Tao, W. and Leu, M. C., “Design of Lattice Structure for Additive Manufacturing,”International Symposium on Flexible Automation, Cleveland, OH, August 1 - 3, 2016.

McMillen, D., Li, W., Leu, W. C., Hilmas, G. E. and Watts, J., “Designed Extrudate for Additive Manufacturing of Zirconium Diboride by Ceramic On-Demand Extrusion,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Li, W., Ghazanfari, A., McMillen, D., Leu, M. C., Hilmas, G. E. and Watts, J., “Properties of Partially Stabilized Zirconia Components Fabricated by the Ceramic On-Demand Extrusion Process,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Motaparti, K. P., Taylor, G., Leu, M. C., Chandrashekhara, K., Castle, J. and Matlack, M., “Effects of Build Parameters on Compression Properties for ULTEM 9085 Parts by Fused Deposition Modeling,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Bham, G. H., Leu, M. C. and Venkat, B., “Examining the Impacts of Portable Changeable Message Signs on Drivers’ Speed Characteristics: A Driving Simulator Study,” 95th Annual Conference of the Transportation Research Board, Washington, DC, January 10 - 14, 2016.

Ghazanfari, A., Li, W., Leu, M. C. and Hilmas, G. E., “A Novel Extrusion-Based Additive Manufacturing Process for Ceramic Parts,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Kriewall, C. S., Sutton, A. T., Leu, M. C., Newkirk, J. W. and Brown, B., “Investigation of Heat-Affected 304L SS Powder and Its Effect on Built Parts in Selective Laser Melting,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Sutton, A. T., Kriewall, C. S., Leu, M. C. and Newkirk, J., “Powders for Additive Manufacturing Processes: Characterization Techniques and Effects on Part Properties,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Liu, X. F., Shahriar, M. R., Sunny, S. M., Leu, M. C., Chen, M. and Hu, L., “Design and Implementation of Cyber-Physical Manufacturing Cloud Using MTconnect,” IDETC/CIE17, Charlotte, NC, August 21 - 24, 2016.

Liu, X. F., Sunny, S. M., Shahriar, M. R., Leu, M. C., Chen, M. and Hu, L., “Implementation of MTConnect for Open Source 3D Printers in Cyber Physical Manufacturing Cloud,” IDETC/CIE17, Charlotte, NC, August 21-24, 2016.

Murphy, C., Kolan, K. C. R., Long, M., Li, W., Leu, M. C., Semon, J. A. and Day, D. E., “3D Printing of a Polymer Bioactive Glass Composite for Bone Repair,” Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Ghazanfari, A., Li, W., Leu, M. C., Watts, J., Zhuang, Y. and Huang, J., “Freeform Extrusion Fabrication of Advanced Ceramic Components With Embedded Sapphire Optical Fiber Sensors,” ASME 2016 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS2016), Stowe, VT, September 28 - 30, 2016.

Taylor, G., Wang, X., Mason, L., Leu, M. C., Chandrashekhara, K., Castle, J. and Matlack, M., “Investigation of Ultem 1010 FDM Sparse-Build Parts Using Design of Experiments and Numerical Simulation,” Composites and Advanced Materials Expo (CAMX 2016), Anaheim, CA, September 26 - 29, 2016.

Liou, F.

Gegesky, M., Liou, F. and Newkirk, J., “Proposed Hybrid Processes for Part Building Using Fusion Welding and Friction Stir Processing,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Karnati, S. and Liou, F., “Investigation of Tensile Properties of Bulk and SLM Fabricated 304L Stainless Steel Using Various Gage Length Specimens,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Li, W., Zhang, J., Karnati, S., Zhang, Y., Liou, F., Newkirk, J., Taminger, K. and Seufzer, W., “Modeling and Experimental Investigation of Pre-Mixed Multi-Powder Flow in Fabricating Functional Gradient Material by Laser Metal Deposition Process,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.


Yan, L., Li, W., Chen, X. and Liou, F.,”Simulation of Cooling Rate Effects on Ti-6Al-4V Microstructure Tailoring in Direct Laser Deposition,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Liu, R., Wang, Z., Zhang, Y., Sparks, T. and Liou, F., “A Smooth Toolpath Generation Method for Laser Metal Deposition,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Wang, F., Liou, F. and Sparks, T., “Integration of Voxel Based and Source Based Representation for Computer Aided Design of Functional Gradient Materials,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Chen, X., Yan, L., Li, W., Liou, F. and Newkirk, J., “Effect of Powder Particle Size on the Fabrication of Ti-6Al-4V Using Laser Metal Deposition from Elemental Powder Mixture,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Pernicka, H.

Darling, J. E., LeGrand, K. A., Galchenko, P., Pernicka, H. J., DeMars, K. J., Shirley, A., McCabe, J., Schmid, C., Haberberger, S. J. and Mundahl, A. J., “Development and Flight of a Stereoscopic Imager for Use in Spacecraft Close Proximity Operations,” 39th AAS Guidance and Control Conference, Paper No. AAS 16-085, Breckenridge, CO, February 2016.

Winter, T., Coleman, B. and Pernicka, H., “Development of a Multidisciplinary Design Analysis and Optimization Toolset for Integrated Spacecraft Subsystem Models,” 17th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, Paper No. AIAA-2016-3363, Washington, DC, June 13 - 17, 2016.

Riggins, D.

Abbas, M. and Riggins, D. W., “Exergy-Based Performance Analysis of a Turbojet Engine,” 52nd AIAA/SAE/ASEE Joint Propulsion Conference, Paper No. AIAA 2016-4638, Salt Lake City, UT, July 2016.

Rovey, J.

Maser, J., Rovey, J. and Yang, X., “Fabrication of Asymmetric Nanostructures for Plasmonic Force Propulsion,” 54th AIAA Aerospace Sciences Meeting, AIAA Science and Technology Forum and Exposition 2016, Paper No. AIAA 2016-0696, San Diego, CA, January 4 - 8, 2016.

Paliwoda, M. C., Rovey, J. L. and Wainwright, M., “Control of Dielectric Barrier Discharge Striations,” 54th Aerospace Sciences Meeting, Paper No. AIAA-2016-0197, San Diego, CA, January 4 - 8, 2016.

Miller, S. W., Prince, B. D., Bemish, R. J. and Rovey, J. L., “Mass Spectrometry of Selected Ionic Liquids in Capillary Electrospray at Nanoliter Volumetric Flow Rates,” 52nd Joint Propulsion Conference, Paper No. AIAA-2016-4740, Salt Lake City, UT, July 25 - 27, 2016.

Glascock, M. S., Rovey, J. L., Williams, S. and Thrasher, J., “Observation of Late-Time Ablation in Electric Solid Propellant Pulsed

Microthrusters,” 52nd Joint Propulsion Conference, Paper No. AIAA-2016-4845, Salt Lake City, UT, July 25 - 27, 2016.

Berg, S. P. and Rovey, J. L., “Decomposition of a Double Salt Ionic Liquid Monopropellant on Heated Metallic Surfaces,” 52nd Joint Propulsion Conference, Paper No. AIAA-2016-4578, Salt Lake City, UT, July 25 - 27, 2016.

Mundahl, A., Berg, S. P. and Rovey, J. L., “Linear Burn Rates of Monopropellants for Multi-Mode Micropropulsion,” 52nd Joint Propulsion Conference, Paper No. AIAA-2016-4579, Salt Lake City, UT, July 25 - 27, 2016.

Wang, C.

Vidal-Meza, M. P., Zhou, R., Barua, S., Wang, C. and Park, J., “Simulation of Interstitial Nanoparticle Flow for Development of Tumor-On-A-Chip Device,” COMSOL Conference Proceedings, Boston, MA, October 5 - 7, 2016.

Wojnar, C.

Bradford, S. C., Hofmann, D. C., Roberts, S. N., Steeves, J. B., Wojnar, C. S. and Kochmann, D. M., “Energy-Efficient Active Reflectors with Improved Mechanical Stability and Improved Thermal Performance,” AIAA Spacecraft 2016, 3rd AIAA Spacecraft Structures Conference, Paper No. AIAA 2016-0702, San Diego, CA, January 4 - 8, 2016.

Wojnar, C. S., le Graverend, J-B. and Kochmann, D. M., “Broadband Electromechanical Spectroscopy: A Method for Measuring the Dynamic Electromechanical Response of Ferroelectrics,” Proceedings of the Society of Experimental Mechanics, Greenville, SC, June 2016.

Hostetler, J., Bender, T., Goldstein, J., Urbas, A., Gutierrez, R., Wojnar, C. and Kinzel, E., “Selective Laser Sintering of Low Density, Low Coefficient of Thermal Expansion Silica Parts,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Yang, X.

Maser, J., Rovey, J. and Yang, X., “Fabrication of Asymmetric Nanostructures for Plasmonic Force Propulsion,” 54th AIAA Aerospace Sciences Meeting, AIAA Science and Technology Forum and Exposition 2016, Paper No. AIAA 2016-0696, San Diego, CA, January 4 - 8, 2016.

Li, C., Yang, X. and Gao, J., “Optical Force in Split Ring Resonator,” Proceedings of the 10th Annual ISC Graduate Research Symposium, Rolla, MO, April 29, 2016.

Hosder, S.

West, T. and Hosder, S., “Chapter 3: Efficient Uncertainty Analysis of Radiative Heating for Planetary Entry,” Uncertainty Quantification in Computational Science: Theory and Application in Fluids and Structural Mechanics, Editor: Sarkar, S., pp. 63 - 920, ISBN: 978-981-4730-57-0, World Scientific Publishing, 2016.

Leu, M.

Leu, M. and Ghazanfari, A., “NX10 for Engineering Design – Learning Edition,” (e-book), Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, 2016.

Liou, F.

Liu, R., Wang, Z., Sparks, T., Liou, F. and Newkirk, J., “Aerospace Applications of Laser Additive Manufacturing,” Laser Additive Manufacturing, Materials, Design, Technologies, and Applications, Editor: Brandt, M., pp. 351 - 371, ISBN: 978-0-08-100433-3, Woodhead Publishing, 2016.

Riggins, D.

Riggins, D. W., “Hypersonic Air-Breathing Propulsion Systems and Key Physics and the Categorization of Modeling and Simulation Approaches,” Simulation Credibility Advances in Verification, Validation, and Uncertainty Quantification, Editors: Mehta, U. and Eklund, D., Chapter 12, pp. 445 - 467, NASA Technical Publication-2016-219422/Joint Army Navy NASA Air Force (JANNAF) GL-2016-0001, November 2016.

Tsai, H.

Hu, J., Rao, Z. H. and Tsai, H. L., “Chapter 5: A Comprehensive Model of the Transport Phenomena in Gas Metal Arc Welding,” Joining Technologies, Editor: Ishak, M., pp. 77 – 101, ISBN 978-953-51-2597-6, 2016.

Balakrishnan, S.

Balakrishnan, S., “Neural Network Based Solutions for Stochastic Optimal Control Using Path Integrals,” AFRL Workshop on Probability, Uncertainty and Decision, Wright State University, Dayton, OH, June 28 - 29, 2016.

Birman, V.

Birman, V., “Multiscale Functionally Graded Tendon-to-Bone Insertion – Mechanistic View,” Saint Louis University, St. Louis, MO, November 1, 2016.

Chen, L.

Chen, L. Y., “Metals Nanoprocessing-Driving Performance and Processing of Metals to the Next Level,” Kansas State University, Manhattan, KS, March 30, 2016.

Chen, L. Y., “Metals Nanoprocessing - Driving Performance and Processing of Metals to the Next Level,” CREST/TIGER Seminar, University of Puerto Rico, Mayaguez Campus, Puerto Rico, December 12, 2016.

DeMars, K.

DeMars, K. J. and McCabe, J. S., “Accounting for Uncertain Parameters in Nonlinear/Non-Gaussian Space Surveillance Tracking,” Air Force Research Laboratory, Kirtland AFB, NM, June 2, 2016.

Du, X.

Du, X., “Reliability Prediction in Early System Design Stage,” Sweden Royal Institute of Technology (KTH), Stockholm, Sweden, April 5, 2016.

CONTRIBUTION TO BOOKS AND BOOKS PUBLISHED

INVITED TALKS


Du, X., “Efficient Simulation for Reliability Analysis with Design of Experiments,” University of Electronic Science and Technology of China, Chengdu, China, May 9, 2016.

Du, X., “Reliability Based Probabilistic Analysis and Design,” Chongqing University of Science and Technology, Chongqing, China, May 26, 2016.

Du, X., “Reliability Prediction in Early System Design Stage,” Zhejiang University of Technology, Zhejiang, China, June 6, 2016.

Hosder, S.

Hosder, S, “Modeling and Simulation of Hypersonic Flows and Uncertainty Analysis,” U.S. Government at Hypersonic Technologies Workshop, Washington, DC, May 2, 2016.

Kinzel, E.

Kinzel, E., “Additive Manufacturing of Glass for Optical Applications,” SPIE Photonics West 2016, San Francisco, CA, February 13 - 18, 2016.

Kinzel, E. C., “Additive Manufacturing of Glass for Optical Applications,” Expert Panel SCHOTT AG, Mainz, Germany, April 13 - 17, 2016.

Kinzel, E., “Additive Manufacturing of Glass for Optical Applications,” Karles Invitational Conference, U.S. Naval Research Laboratory, Washington, DC, August 12, 2016.

Landers, R. G.

Landers, R. G., “Advanced Manufacturing I: Additive Processes,” Mechatronics and Intelligence in Manufacturing, Shiv Nadar University, India, November 26 - 27, 2016.

Landers, R. G., “Advanced Manufacturing I: Machining/Joining Processes,” Mechatronics and Intelligence in Manufacturing, Shiv Nadar University, India, November 26 - 27, 2016.

Landers, R. G., “Advanced Manufacturing II: Equipment,” Mechatronics and Intelligence in Manufacturing, Shiv Nadar University, India, November 26 – 27, 2016.

Leu, M.

Leu, M., “Rapid Freeze Prototyping and Freeze-Form Extrusion Fabrication,” lecture for mechanical engineering class, Nanyang Technology University, SINGAPORE, August 17, 2016.

Leu, M., “Some Recent Advances and Future Research Opportunities of Additive Manufacturing,” Nanyang Technology University, SINGAPORE, August 12, 2016.

Liou, F.

Liou, F. W., “Model-Based Qualification for Directed Energy Deposition Processes,” 145th TMS Annual Meeting & Exhibition, Nashville, TN, February 16 - 18, 2016.

Liou, F., “Metal Additive Manufacturing,” School of Engineering, National Cheng-Kung University, Tainan, Taiwan, June 16, 2016.

Liou, F., “Multiscale and Multiphysics Modeling of Metallic Additive Manufacturing,” Joint Army-Navy-NASA-Air Force (JANNAF) Liquid Propulsion Subcommittee (LPS)

Advanced Materials Panel meeting 2016, Jackson Center, Huntsville, AL, August 23 - 25, 2016.

Liou, F., “Hybrid Manufacturing Processes for Precision Metal Parts,” Joint Army-Navy-NASA-Air Force (JANNAF) Liquid Propulsion Subcommittee (LPS) Advanced Materials Panel meeting 2016, Jackson Center, Huntsville, AL, August 23 - 25, 2016.

Midha, A.

Midha, A., “Compliant Mechanisms: Memory Lane, the Journey, and the Exciting Road Ahead,” Missouri University of Science and Technology Council of Graduate Students Forum, Ignite Rolla, with the theme Breaking Barriers, October 25, 2016.

Pan, H.

Pan, H., “Transport and Interfacial Phenomena in Micro/Nanoscale Confined Crystallization,” Micro/Nanoscale Heat Transfer and Energy Workshop, Kenting, Taiwan, October 1, 2016.

Pan, H., “Micro/Nano Additive Manufacturing for Electronics and Energy Devices,” Department of Mechanical Engineering, National Chung Hsing University, Taichung City, Taiwan, October 3, 2016.

Park, J.

Park, J., “Why Do Lithium Ion Batteries Degrade?” Chemical and Biochemical Engineering Graduate Seminar, Missouri University of Science and Technology, January 26, 2016.

Pernicka, H.

Pernicka, H. J., “Small Satellite Program at S&T,” Sandia National Laboratories, Albuquerque, NM, January 19, 2016.

Pernicka, H. J., Keynote Speaker, Missouri University of Science and Technology, Launch! Event, Rolla, MO, October 25, 2016.

Pernicka, H. J., Keynote Speaker, Missouri University of Science and Technology, Sigma Pi Fraternity Annual Scholarship Banquet Dinner, Rolla, MO, November 17, 2016.

Rovey, J.

Rovey, J. and Yang, X., “Plasmonic Space Propulsion,” NASA Innovative Advanced Concepts Symposium, Raleigh, NC, August 2016.

Tsai, H.

Tsai, H. L., “3D Printing of Large, Metallic Glass Structures with Complex Geometry,” Liquidmetal Technologies, Inc., Rancho Santa Margarita, CA, November 8, 2016.

Wang, C.

Wang, C., “Microscale Magnetic Fields for Particle Separation,” Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian, China, June 9, 2016.

Wojnar, C.

Wojnar, C. S., “Towards High Stiffness, High Damping Materials via Electrically-Tuning Instabilities in Ferroelectrics,” Army Research Laboratory, Aberdeen, MD, October 5, 2016.

Wojnar, C. S., “Towards High Stiffness, High

Damping Materials via Electrically-Tuning Instabilities in Ferroelectrics,” Materials Science and Engineering Seminar, Missouri University of Science and Technology, Rolla, MO, October 27, 2016.

Wojnar, C. S., “Towards High Stiffness, High Damping Materials via Electrically-Tuning Instabilities in Ferroelectrics,” Computational Mechanics and Physics of Solids Seminar, University of Colorado Boulder, CO, October 12, 2016.

Wojnar, C. S., “Preventing Solid Rocket Motor Failures by Investigating the Mechanics of Aging in Propellant,” Mechanical and Aerospace Engineering Seminar, University of Colorado Colorado Springs, Colorado Springs, CO, October 14, 2016.

Birman, V.

Birman, V. and Vo, N., “Wrinkling in Sandwich Structures with a Functionally Graded Core,” ASME International Mechanical Engineering Congress and Exposition (IMECE 2016), Paper No. 68340, Phoenix, AZ, November 11 - 17, 2016.

Frostig, Y., Kardomateas, G. A. and Birman, V., “Non-Linear Geometrical Behavior of a Sandwich Panel with an FGM Core - Extended High Order Approach,” ASME International Mechanical Engineering Congress and Exposition (IMECE 2016), Paper No. 67466, Phoenix, AZ, November 11 - 17, 2016.

Genin, G. M., Birman, V. and Thomopoulos, S., “Multiscale Mechanics at Biological Interfaces,” Sino-US Biomedical Engineering and Medical Robotics Interdisciplinary Innovation Forum, Suzhou, China, November 3 - 6, 2016.

Bristow, D.

Luo, J., Gilbert, L. J., Peters, D. C., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Glass,” SPIE Defense and Commercial Sensing, Baltimore, MD, April 2016.

Luo, J., Bender, T., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Borosilicate Glass,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Duan, L.

Duan, L., “Development of Acoustic Model for Receptivity in Conventional Hypersonic Wind Tunnels,” AIAA SciTech16 Boundary Layer Transition Forum, San Diego, CA, January 4 - 8, 2016.

Duan, L., “Progress on Tunnel Noise Simulation and Modeling,” AVT-240 Specialist Meeting on Hypersonic Boundary-Layer Transition Prediction, University of Notre Dame, South Bend, IN, April 11 - 12, 2016.

Duan, L., “Numerical Simulation of Freestream Acoustic Disturbances in Hypersonic Ground Facilities and Their Effect on Boundary Layer Transition,” 2016 AFOSR High Speed Aerodynamics Portfolio and ONR Hypersonics Portfolio Review Conference,

CONFERENCE PRESENTATIONS


Arlington, VA, June 27 - 30, 2016.

Isaac, K.

Isaac, K. M., “Redox MHD-Based Lab-On-A-Chip,” Ozark Biomedical Initiative Symposium Proceedings, Rolla, MO, February 27, 2016.

Zhao, Y., Yan, G., Zu, J., Yuan, F. and Isaac, K. M., “Comparison on Wind Effects of Tornadic and Straight-Line Wind Fields on Spherical Dome Structures,” The 8th International Colloquium on Bluff Body Aerodynamics and Applications, Boston, MA, June 7 - 11, 2016.

Yuan, F. and Isaac, K. M., “Chaotic Advection Enhanced Mixing in Three Dimensional MHD Flows in Microfluidic Devices,” 229th Electrochemical Society Meeting, San Diego, CA, May 29 - June 2, 2016.

Zhao, Y., Yan, G. and Isaac, K. M., “Characteristics of Wind Flow Around Dome Structures in Tornadic Wind Field,” 4th American Association of Wind Engineering Workshop, Miami, FL, August 2016.

Yuan, F. and Isaac, K. M., “A Computational Model for Natural Convection and Forced Convection in Redox MHD Systems Based on Electroneutrality and Migration, Fundamentals and Applications of Microfluidic and Nanofluidic Devices,” PRiME: Joint International Meeting of Electrochemical Society of Japan, Electrochemical Society and Korean Electrochemical Societey, Honolulu, Hawaii, October 2 - 7, 2016.

Kinzel, E.


Qu, C. and Kinzel, E. C., “Infrared Metasurfaces Fabricated with Microsphere Photolithography,” 2016 MRS Spring Meeting & Exhibit, Phoenix, AZ, March 28 - April 1, 2016.

Pribe, J. D., Thandu, S. C., Yin, Z. and Kinzel, E. C., “Toward DMD Illuminated Spatial-Temporal Modulated Thermography,” SPIE DCS, Baltimore, MD, April 2016.

Liu, T., Qu, C., Almasri, M., and Kinzel, E. C., “Design and Analysis of Frequency Selective Surface Enabled Microbolometers,” SPIE DCS, Baltimore, MD, April 2016.

Luo, J., Gilbert, L. J., Peters, D. C., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Glass,” SPIE DCS, Baltimore, MD, April 2016.

Luo, J., Bender, T., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Borosilicate Glass,” Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Kinzel, E., “Low-Cost, Large-Area Patterning of Metasurfaces with Off-Axis Microsphere Photolithography,” Materials Research Society Fall Meeting, Boston, MA, November 27 - December 2, 2016.

Landers, R. G.

Luo, J., Gilbert, L. J., Peters, D. C., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Glass,” SPIE Defense and Commercial Sensing, Baltimore, MD, April 2016.

Luo, J., Bender, T., Bristow, D. A., Landers, R. G., Goldstein, J. T., Urbas, A. M. and Kinzel, E. C., “Bubble Formation in Additive Manufacturing of Borosilicate Glass,” 27th Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 - 10, 2016.

Kinzel, E. C., Lou, J., Gilbert, L., Peters, D., Landers, R. G., Bristow, D. A., Goldstein, J. and Urbas, A., “Bubble Formation in the Additive Manufacturing of Glass,” 27th Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 – 10, 2016.

Gegel, M. L., Bristow, D. A., Landers, R. G. and Nisbett, A., “Laser Line Scan Characterization of Geometric Profiles in Laser Metal Deposition,” 27th Annual International Solid Freeform Fabrication Symposium, Austin, TX, August 8 – 10, 2016.

Leu, M.

Leu, M., “Constitutive Modeling and Experimental Verification of Aqueous-Based Freeform Extrusion Fabrication Processes,” 2016 TMS Annual Meeting and Exposition, Nashville, TN, February 17, 2016.

Liou, F.

Liou, F., “Evaluation of Die Repair Using Metal Deposition Process,” Industrial Advisory Board Meeting of the Center for Aerospace Manufacturing Technologies, St. Louis, MO, May 19, 2016.

Liou, F., “Additive Manufacturing Simulator,” Industrial Advisory Board Meeting of the Center for Aerospace Manufacturing Technologies, St. Louis, MO, May 19, 2016.

Liou, F., “Simulation of a Laser Wire Deposition Process for Ti6Al4V Components,” Industrial Advisory Board Meeting of the Center for Aerospace Manufacturing Technologies, St. Louis, MO, May 19, 2016.

Park, J.

Hosop, S., Park, J. and Lu, W., “Interfacial Chemistry and Mechanics of Fluoroethylene Carbonate (FEC)-Derived Electrode/Electrolyte Interfaces,” 18th International Meeting on Lithium Batteries, Chicago, IL, June 19 - 24, 2016.

Shin, H., Park, J. and Lu, W., “Unraveling the Chemical/Structural Degradation Mechanisms of the Graphite/SEI in the Presence of Dissolved Manganese Ions in Li-Ion Batteries,” 229th Electrochemical Society Meeting, San Diego, CA, May 29 - June 2, 2016.

Shin, H., Lu, W. and Park, J., “Mechanical Properties of Solid Electrolyte Interphase Layer in Li-Ion Batteries: Experimental and Computational Studies,” 18th International Meeting on Lithium Batteries, Chicago, IL, June 19 - 24, 2016.

Leong, A., Sarkar, S. and Park, J., “Fabrication of Electrospun Nanofibrous SPEEK Membranes for Use in Vanadium Flow

Batteries,” Solid Freeform Fabrication Symposium, Austin TX, August 7 - 9, 2016.

Lie, J. and Park, J., “A Three-Dimensionally Structured Hybrid Electrodes for Energy Storage Devices,” 2016 Defense Innovation Summit, Austin, TX, November 29 - December 1, 2016.

Sarka, S., Patel, R. L., Liang, X. and Park, J., “Impact of Ultrathin Coating on Lithium-Ion Battery Cathode Materials,” 2016 Defense Innovation Summit, Austin, TX, November 29 - December 1, 2016.

Rovey, J.

Rovey, J. L. and Pernicka, H. J., “Multi-Mode Micropropulsion CubeSat Technology Demonstration Mission,” AFRL NanoSat 9 Kickoff Meeting, Albuquerque, NM, January 18, 2016.

Pernicka, H. J. and Rovey, J. L., “Small Satellite Program at Missouri S&T,” Sandia National Laboratory, Albuquerque, NM, January 19, 2016.

Rovey, J., “Ionization in Solid Electric Propellant Thruster Plumes,” Digital Solid State Propulsion, 6th Technical Exchange Meeting, Reno, NV, February 24 - 25, 2016.

Rovey, J. L. and Yang, X., Plasmonic Space Propulsion,” NASA Innovative Advanced Concepts Symposium, Raleigh, NC, August 2016.

Berg, S. P. and Rovey, J. L., “Design and Development of a Multi-Mode Monopropellant-Electrospray Micropropulsion System,” 30th Annual AIAA/USU Conference on Small Satellites, Logan, UT, August 6 - 11, 2016.

Tsai, H.

Shen, Y. and Tsai, H. L., “Manufacturing of 3D, Large, Complex Geometry of Metallic Glass Structures,” 2016 Defense Innovation Summit, Austin, TX, November 29 - December 1, 2016.

Wang, C.

Zhou, R. and Wang, C., “Fabrication and Optimization of Microscale Magnetic Structures for Magnetic Particle Separation,” International Conference of Microfluidics, Nanofluidics and Lab-on-a-Chip, Dalian, China, June 10 - 12, 2016.

Zhou, R. and Wang, C., “Focusing and Separating Diamagnetic Particles with Multiphase Ferrofluids,” International Conference of Microfluidics, Nanofluidics and Lab-on-a-Chip, Dalian, China, June 10 - 12, 2016.

Wang, C. and Zhou, R., “Shape-Based Separation of Microparticles with Magnetic Fields,” 69th American Physical Society Division of Fluid Dynamics Meeting, Portland, OR, November 20 - 22, 2016.

Wojnar, C.

Hays, W. K. and Wojnar, C. S., “An Experimental Set-Up for Probing Domain Switching in Ferroelectrics at Cryogenic Temperatures,” Midwest Experimental Mechanics Student Conference, University of Illinois at Urbana-Champaign, Urbana, IL, April 2016.


Wojnar, C. S., “An Experimental Set-Up for Probing Domain Switching in Ferroelectrics at Cryogenic Temperatures,” International Congress on Theoretical and Applied Mechanics, Montreal, Canada, August 21 - 26, 2016.

Wojnar, C. S., “Measuring the Dynamic Electromechanical Response of Ferroelectrics,” International Congress on Theoretical and Applied Mechanics, Montreal, Canada, August 2016.

Wojnar, C. S., “Identifying Kinetic Relation Parameters in Ferroelectricity Models via Viscoelasticity Measurements,” Society of Engineering Science, College Park, MD, October 2 – 5, 2016.

Hays, W. K. and Wojnar, C. S., “Influence of Electric Field-Induced Domain Wall Motion on Mechanical Damping,” Society of Engineering Science, College Park, MD, October 2 - 5, 2016.

Bristow,D.

Luke Gilbert (MSME), Advisor: Bristow,D., “Design and Fabrication of a System for the Additive Manufacturing of Transparent Glass,” May 2016.

Patrick Sammons (PhDME), Advisor: Bristow, D., “Repetitive Process Control of Additive Manufacturing with Application to Laser Metal Deposition,” June 2016.

Chandrashekhara, K.

Zhen Huo (PhDME), Advisor: Chandrashekhara, K., “Modeling and Evaluation of Moisture Diffusion in Polymer Composite Materials,” June 2016.

James R. Nicholas (PhDME), Advisor: Chandrashekhara, K., “Manufacturing of Advanced Continous Fiber Reinforced Composites for High Temperature Applications,” December 2016.

DeMars, K.

Samuel Haberberger (MSAE), Advisor: DeMars, K., “An IMU-Based Spacecraft Navigation Architecture Using a Robust Multi-Sensor Fault Detection Scheme,” March 2016.

Jacob Edward Darling (PhDAE), Advisor: DeMars, K., “Bayesian Inference for Dynamic Pose Estimation Using Directional Statistics,” October 2016.

Dharani, L.

Joshua A. Crews (PhDME), Advisor: Dharani, L., Co-Advisor: Midha, A., “Methodology for Analysis of Stress, Creep and Fatigue Behavior of Compliant Mechanisms,” September 2016.

Drallmeier, J.

Allen Ernst (MSME), Advisor: Drallmeier, J., “Addressing the Influence of Carbon Monoxide on the Behavior of an HCCI Engine,” November 2016.

Du, X.

Guannan Liu (MSME), Advisor: Du, X., “The Evaluation of Sequential Optimization and

Reliability Analysis,” March 2016.

Zhifu Zhu (PhDME), Advisor: Du, X.,”Efficient Time-Dependant System Reliability Analysis,” October 2016.

Homan, K.

Pramod N. Bangalore (MSME), Advisor: Homan, K., “Mixing Dynamics in Municipal Water Storage Tanks,” April 2016.

Hosder, S.

Andrew Brune (PhDAE), Advisor: Hosder, S., “Uncertainty Quantification Applied to the Analysis and Design of a Hypersonic Inflatable Aerodynamic Decelerator for Spacecraft Reentry,” October 2016.

Isaac, K.

Fangping Yuan (PhDAE), Advisor: Isaac, K., “Transient CFD Simulations of Pumping and Mixing Using Electromagnetic/Lorentz Force in Microfluidics,” July 2016.

Landers, R. G.

Nima Lofti Yagin (PhDME), Advisor: Landers, R., “Modeling and Control of Fuel Cell-Battery Hybrid Energy Sources,” June 2016.

Leu, M.

Shixuan Meng (MSME), Advisor: Leu, M., “Investigation of the Effect of the Sparse-Build Internal Structure on the Performance of Fused Deposition Modeling Parts,” January 2016.

Shuang Wu (MSME), Advisor: Leu, M., “Engine Sound Simulation and Generation in Driving Simulator,” May 2016.

Liou, F.

Sriram P. Isanaka (PhDME), Advisor: Liou, F., “Novel Design and Manufacturing Strategies for Air Breathing Proton Exchange Membrane,” April 2016.

Megan Gegesky (MSME), Advisor: Liou, F., “Hybrid Manufacturing Processes for Fusion Welding and Friction Stir Welding of Aerospace Grade Aluminum Alloys,” April 2016.

Prabhakar Bala (MSMFG), Advisor: Liou, F., “Prediction of Surface Roughness in Abrasive Waterjet Cutting of Graphite Composite Using Response Surface Methodology,” May 2017.

Fangquan Wang (MSMFG), Advisor: Liou, F., “Composite Model Representation for Computer Aided Design of Functional Gradient Materials,” June 2016.

Zhiyuan Wang (PhDME), Advisor: Liou, F., “Research on Hybrid Manufacturing Using Industrial Robot,” June 2016.

Mohammad Masud Parvez (MSMFG), Advisor: Liou, F., “Design of an Adaptive Force and Stiffness Controlled Compliant Device for Robotic Polishing,” July 2016.

Renwei Liu (PhDME), Advisor: Liou, F., “Repair of Metallic Components Using Hybrid Manufacturing,” November 2016.

Ninad Kulkarni (MSMFG), Advisor: Liou, F., “Error Mapping of Build Volume in Slective Laser Melting,” December 2016.

Midha, A.

Joshua A. Crews (PhDME), Advisor: Dharani, L., Co-Advisor: Midha, A., “Methodology for Analysis of Stress, Creep and Fatigue Behavior of Compliant Mechanisms,” September 2016.

Pan, H.

Bikram K. Mahajan (MSME), Advisor: Pan, H., “Synthesis and Photonic Sintering of Bioresorbable Zinc Nanoparticles for Transient Electronics Manufacturing,” June 2016.

Pernicka, H.

James Veerkamp (MSAE), Advisor: Pernicka, H., “Development and Testing of a Fracture Energy-Based Model of Explosive Asteroid Deflection,” March 2016.

Abdalla Bani (MSME), Co-Advisor: Pernicka, H., “Design and Numerical Analysis of an Axisymmetric Aerospike Micro-Nozzle for a Refrigerant-Based Cold-Gas Propulsion System for Small Satellites,” August 2016.

Rovey, J.

Matthew Paliwoda (MSAE), Advisor: Rovey, J., “Intensity Control of Dielectric Barrier Discharge Filaments,” May 2016.

Matthew Glascock (MSAE), Advisor: Rovey, J., “Characterization of Electric Solid Propellant Pulsed Microthrusters,” November 2016.

Yucelen, T.

Daniel Wagner (MSME), Advisor: Yucelen, T., “A Linear Matrix Inequality-Based Approach for the Computation of Actuator Bandwith Limits in Adaptive Control,” May 2016.

M.S. THESIS AND PH.D. DISSERTATIONS


MAEM E C H A N I C A L A N D A E R O S PA C E E N G I N E E R I N G

Department of Mechanical and Aerospace EngineeringMissouri University of Science and TechnologyRolla, MO 65409

MAE Repor… · James McCabe (PhDAE), Advisor: DeMars, K. J., NASA Space Technology Research...

Documents

Transcript of MAE Repor… · James McCabe (PhDAE), Advisor: DeMars, K. J., NASA Space Technology Research...