Installation Manual Sirius i30 - Keyprocessor · 1.3.2 Chip Serial Number (CSN) Part number:...
Transcript of Installation Manual Sirius i30 - Keyprocessor · 1.3.2 Chip Serial Number (CSN) Part number:...
Publication
November 2014,
Keyprocessor BV
Paasheuvelweg 20
1105BJ Amsterdam, The Netherlands
www.keyprocessor.com
Tel.: +31-20-4620700
This manual represents the knowledge at the above mentioned time. Keyprocessor works non-
stop to improve her products. For the most recent technical information please contact your
consultant or dealer.
Content overview
Publication .................................................................................................................... 2 Content overview .......................................................................................................... 2 1 The product .................................................................................................... 3 1.1 Sticker i-serie ............................................................................................. 3 1.2 Spacers ...................................................................................................... 4 1.3 Default reader configurations ........................................................................ 4 1.3.1 Polyx/Orbit Mifare- MifareDesfire ................................................................... 4 1.3.2 Chip Serial Number (CSN) ............................................................................ 5 1.3.3 Sirius i-30 programmable using configuration cards ......................................... 5 1.3.4 Sirius i-30 programmable using PC application and configuration cards .............. 5 2 Installation and use ......................................................................................... 6 2.1 Location ..................................................................................................... 6 2.2 Mounting .................................................................................................... 6 3 Connection ..................................................................................................... 8 3.1 Sirius i30 connector lay-out .......................................................................... 8 3.2 If door controller Polyx ................................................................................. 9 3.2.1 Direct connection (RS485) ........................................................................... 9 3.2.2 Connection using an Adapterboard ............................................................... 10 3.3 If door controller Orbit ................................................................................ 11 3.3.1 Connecting with UTP cable ........................................................................... 11 3.3.2 Connection with CKY 3x2x0,14mm² .............................................................. 11 4 Technical data................................................................................................ 12 4.1 Cabel specifications .................................................................................... 13 4.1.1 Data signal Clock/Data ................................................................................ 13 4.1.2 Data signal Wiegand ................................................................................... 13 4.1.3 Data signal RS485 ...................................................................................... 14 4.2 Certificates ................................................................................................ 15
1 The product
The Sirius i-series card reader is a versatile card reader which supports multiple card
technologies and communication protocols. In addition, this card reader is able to support
different technologies simultaneously like Mifare classic and DESFire EV1.
The card reader is equipped with a function to automatically adjust the antenna on and off
when no activity takes place around the card reader. The detection is based on proximity.
The purpose of this functionality is to create a card reader as energy efficient as possible and
only activate the antenna when a person or card is detected near to the card reader.
This manual provides the necessary information concerning the installation instructions,
mounting and use of the card reader which is supplied as standard.
The Sirius i-series card reader:
i30: picture 1 i30: Picture 2
1.1 Sticker i-serie
On the back of the card reader a sticker placed.
This sticker features a QR code.
After scanning this QR code, all necessary information
will be downloaded automatically.
1.2 Spacers
Several types of Spacers have been developed for specific purposes. It can make the card
reader more robust for external influences but it can also be useful when installing the Sirius
card reader on existing plants.
801-6101 Sirius i30 Spacer
801-6102 Sirius i30 Spacer wide
801-6107 Sirius i30 Mounting plate for Sirius i30 spacer protector (801-6109)
801-6109 Sirius i30 Spacer protector
801-6110 Sirius i30 Spacer cardholder
1.3 Default reader configurations
When using a default Sirius i-series card reader, four configurations are possible
The configurations are described in the paragraphs below.
Remark: For more information about the additional options, please contact your contact at
Keyprocessor.
1.3.1 Polyx/Orbit Mifare- MifareDesfire
Part number: 801-5101
Standard communication:
A Polyx based on RS485
An Orbit based on Clock/Data - MIFARE Classic & MIFARE DESFire EV1(coded)
Output length when using Clock/Data:
When using Mifare Classic, the output length is 8 digits
When using Mifare DESFire, the output length is 12 digits
Standard LED function:
When the reader is provided with power, the LED color is Red.
When the LED connection is switched to GND, the LED color is Green
Standard IO function:
When using Mifare Classic, the output length is 8 digits
A standard configured card reader does not use the extra IO functionality. When this
function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4
Programmable:
The card reader is not programmable.
1.3.2 Chip Serial Number (CSN)
Part number: 801-5102
Default Card reader protocol:
An Orbit based on Clock/Data.
Output length based on Clock/Data:
The length of the Chip Serial Number (CSN) is 4 byte swapped (10 digits decimal)
Attention! When using a 7 byte (random) CSN, the card reader must communicate with a
Polyx. In this case you need to order another card reader. See chapter 1.3.3 &
1.3.4
Standard LED function:
When the reader is provided with power, the LED color is Red.
When the LED connection is switched to GND, the LED color is Green
Standard IO function:
A standard configured card reader does not use the extra IO functionality. When this
function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4
1.3.3 Sirius i-30 programmable using configuration
cards
Part number: 801-5103
After connecting the Power to the card reader, the LED turns blue. A configuration card
is needed to turn the reader in operational mode.
You can order a configuration card via Keyprocessor. To create 'custom' configuration
cards extra costs will be calculated.
1.3.4 Sirius i-30 programmable using PC application
and configuration cards
Part number: 801-5104
After connecting the Power to the card reader, the LED turns blue. A configuration card
is needed to turn the reader in operational mode.
The card reader is fully programmable using a PC application and you’re able to create
your own configuration cards.
2 Installation and use
2.1 Location
Determine the location where the Sirius card reader should be installed. There is a
maximum cable length between the reader and door controller.
Exception: using an external power supply, you can increase the achievable distance
between the door controller and card reader.
Install the reader with a minimum lateral distance of 20 cm from each other.
The reader should preferably NOT be installed to metal. If necessary, use a spacer, see
chapter 1.2.
2.2 Mounting
Mount the card reader preferably on a flat surface.
Picture 3: Sirius i30 measurements
Mount the back plate of the card reader to the appropriate place.
If placed on a stone wall, drill two 6mm holes intended for the plugs.
If placed on a wooden surface, drill two 3mm holes.
The screw hole of the card reader should be placed on the underside. (see Picture 4)
Pull the cable through the mounting plate (and the spacer, if applicable) of the Sirius
reader.
Screw the back plate of the reader with adequate screws. The head of the screw must
be at least 6 mm wide.
When not removed, remove the orange colored film of the Buzzer.
Click the front of the card reader at the top of the mounting plate
Attach the front of the card reader to the mounting plate with the supplied 'special
mounting bolt.
3 Connection
Remark! Depending on the configuration of the card reader, the inputs and outputs of the
card reader can be used.
3.1 Sirius i30 connector lay-out
Connect the cable as shown in this chapter
The reader accepts a supply voltage of 5.0 - 16.0 VDC.
A higher input voltage results in a lower power consumption and provide cost-effective wiring
with a smaller diameter of the conductor.
When using an external power supply, it must comply with the SELV guidelines.
Pin number Clock/Data Wiegand RS485
7 Vcc (+) Vcc (+) Vcc (+)
6 GND (-) GND (-) GND (-)
5 Ext. Input 1(LED) Ext. Input 1(LED) Ext. Input 1
4 Clock D1 Ext. Output 2
3 Data D0 Ext. Output 1
2 Ext. Input 2 Ext. Input 2 B
1 Ext. Output 1 Ext. Output 1 A
3.2 If door controller Polyx
The Sirius card reader can be connected in two ways with the Polyx: directly or by using an
Adapterboard
For optimal communication, it is recommended to have the latest version of one of the
following operating system
2.6 JFSS2
3.3 UbiFS
Remark! Browse to the polyx to see the version information. For more information about
the versions, see the KP_Install_update_Polyx manual.
3.2.1 Direct connection (RS485)
Recommended cable type between a Polyx and the Sirius card reader is: (see Section 4.1 for
more information)
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors
A direct connection (without using an Adapterboard) between the Sirius card reader and a
Polyx™ is NOT possible when:
Sirius and Polyx™ are installed in different buildings and thus the connection
leaves the building or
the wiring is no UTP cable (CAT5 or CAT6) or
an existing (non UTP) cable is reused or
overvoltage protection for the card reader is required or
An external power supply is required for the card reader.
If any of the above conditions applies, see chapter 3.2.2.
Polyx, directly connected to a Sirius card reader:
Pin number RJ-
45 Plug
Polyx™ PRT 2/3
TIA/EIA-568-B
Cable color
Signal Connection
Sirius i30 card
reader
1 White/orange B 2 2 Orange A 1 3 White/green B 2 4 Blue Vcc (+) 7 5 White/blue 6 Green A 1 7 White/brown 8 Brown GND (-) 6
Picture T-568B
3.2.2 Connection using an Adapterboard
Recommended cable type between a Polyx and the Sirius card reader, using an Adapterboard
is:
Shielded cable with twisted pairs
If a direct connection is not possible, an Adapterboard must be placed between Polyx and the
Sirius card reader.
Adapterboard and Polyx are connected with a default UTP cat5 cable (or higher) (plug
connection).
Connecting wires as shown in the diagrams below.
Or screw
connection
on Adapterboard
Or RJ45
connection
on
Adapterboard
TIA/EIA-568-B
Cable color
Signal Connection
Sirius i30 card
reader
A (or 1) 1 White/orange B 2
B (or 2) 2 Orange A 1
Y (or 3) 3 White/green B 2
“+” 4 Blue Vcc 7
5 White/blue
Z (or 6) 6 Green A 1
7 White/brown
“—” 8 Brown GND (-) 6
Connect GND of the Adapterboard to the local Earth.
Connect the shield of the ground cable to the GND connection of the Adapterboard.
Do not place any jumpers! For more information see the Adapterboard manual..
Possible connections of the card reader Sirius on the Adapterboard
3.3 If door controller Orbit
Recommended cable type between the Orbit and Sirius card reader:
CKY 3x2x0,14mm²
CKY 4x2x0,14mm²
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors
3.3.1 Connecting with UTP cable
TIA/EIA-568-B
Cable color
Connection
on the Orbit
Connection
Sirius i30 card reader
White/orange Data/D0 3 Orange - - White/green Clock/D1 4 Blue +5V 7 White/blue LED 5 Green - - White/brown GND 6 Brown GND 6
3.3.2 Connection with CKY 3x2x0,14mm²
Cable color Connection
on the Orbit
Connection
Sirius i30 card reader
Green Data/D0 3 Yellow Clock/D1 4 Pink +5V 7 Grey LED 5 White GND 6 Brown GND 6
4 Technical data
Model Sirius i30 card reader
Interface Sirius Clock/Data, Wiegand Sirius - Polyx™ (RS485)
Data type Read Read/write
Readable cards Mifare 1K, Mifare 4K, Mifare
DESFire 0.6, Mifare DESFire EV1
8K and ISO14443A compatible
card
Mifare 1K, Mifare 4K, Mifare
DESFire 0.6, Mifare DESFire
EV1 8K, Rijkspas and
ISO14443A compatible card
Power supply 5-16V DC Average: 0,7W
Peak: 1,4W
5-16V DC Average: 0,7W
Peak: 1,4W
Led consumption, both on
100%
On 12V, max. 1,8W
LED input LED input with pull-up, active low
Ext. output max. Voltage 45V; Open collector output; sinked current. Max.
current 500mA
Ext. input 1 Resistance 1kOhm
Dimensions (mm) i30 142x45x22
Reading Distance i30 5mm-70mm for ISO14443A Mifare card; (depending on
environment and transponder)
Environmental Rating i30 IP64
Operating Temperature -31º to 150º F (-35º to 65º C)
Storage Temperature -67º to 185º F (-55º to 85º C)
Operating Humidity 5% to 95% relative humidity non-condensing
Transmit Frequency 13.56 MHz
Standard ISO14443 A
Indicators 2x RGB LED and 1 buzzer
Connection 7-pin screw connector
Certifications CE
4.1 Cabel specifications
Cable specifications (non-shielded)
4.1.1 Data signal Clock/Data
4.1.2 Data signal Wiegand
Interface
Maximum cable length
min.conductor size with
12 VDC supply 1 = 5V DC
Meters Feet mm2 AWG
Wiegand
40 130 0.14 26
80 260 0.25 24
120 390 0.34 22
Clock/Data 201 661
0.14 26
0.25 24
0.34 22
RS485 (cable
power)
120 200 0.25 24
150 490 0.34 22
RS485 (external
power) 600 1965 0.25 24