History and Resources - Watson Packer

www.watsonpacker.com • 432.552.0102

rev. 04/2014 2 wat s o n pac ker llc p ri c e b o o k

Odessa, Texas Richard MayfieldDistrict Manager

2201 W. 39th432-552-9325

Monahans, TexasJoe Romo

District Manager2909 S. Stockton Hwy

432-943-7006

Andrews, TexasBen Kemp

District Manager410 NW Mustang Dr.

432-524-4385

San Angelo, TexasRicky Day

District Manager4825 Old Christoval Rd.

325-617-5841

Hobbs, New MexicoRene Juarez Jr.

District Manager320 NW County Road

PO Box 748575-393-0918

Midland, TexasCorporate Office

600 N. Big SpringMidland, TX 79701

432-620-0062

Watson Packer LocationsJustin McKee-General Manager

432.552.0102 • www.watsonpacker.com

3wat s o n pac ker llc p ri c e b o o krev. 04/2014

History and ResourcesWatson Packer was founded in 1963 in Monahans, Texas by Bill Watson. Over the next several years, the company expanded into Seminole, Snyder, and Abilene, Texas. Harold Clifton, having twenty years of experience at Baker Oil Tools, joined the team as Operations Manager in 1977. In 1996, Watson Packer was sold to Weatherford after growing to over 60 employees in sixteen stores throughout Texas, New Mexico, Oklahoma, Colorado and Utah. Weatherford changed the name of the company to Weatherford Completion Systems. In 1998 Bill Watson, Barry Watson and James Harvey started a new company under the Watson Packer name with Harold Clifton as Operations Manager. Watson Packer currently has over 60 employees with stores located throughout Texas and New Mexico. In 2014 Justin McKee became the new General Manager of Watson Packer. Justin has over 20 years of downhole tool knowledge and experience and will continue to lead Watson Packer in providing our customers with exceptional downhole service and knowledge.

Watson Packer is a distributor for all of the major independent tool manufactures, such as Weatherford, Baker Tools, D & L Oil Tools and Kline Tools. We have Tech Units for specifications, dimensions and operating instructions available on all the tools we run. We also carry a large inventory of packers, bridge plugs, anchors, as well as our new CRP Packer, which is quickly becoming one of the most popular tools used in the Oil Field. We repair any kind of packer or tubing anchor including Baker, Arrow, Guiberson and Halliburton.

We believe that Watson Packer has the most experienced servicemen in the Permian Basin and the right tools needed for your oil and gas well. We would appreciate the opportunity to add your company to our list of satisfied customers.



ProductsModel ‘CRP’ Rotation Set Packer .................................................................................................. 6

ROTO-SET Packer ....................................................................................................................... 7

WRL Production Packer ................................................................................................................ 8

Type T Squeeze Packer ................................................................................................................. 9

Crest III Packer ............................................................................................................................ 10

HD Retrievable Packer................................................................................................................. 11

TS Retrievable Bridge Plug .......................................................................................................... 12

WLTC Retrievable Bridge Plug ................................................................................................... 13

Type C Perforation Wash Tool ..................................................................................................... 14

Stradasnap .................................................................................................................................... 15

Type H Tension Packer ................................................................................................................ 16

PCR Cement Retainer ................................................................................................................. 17

Lok-Set Packer ........................................................................................................................18-19

ASI-X Packer ..........................................................................................................................20-21

VSI-XW Wireline Set Production Packer ..............................................................................22-23

R-3 Double Grip Packer .........................................................................................................24-25

T-2 On-Off Tool .......................................................................................................................... 26

ASII Packer .................................................................................................................................. 27

ASIII Packer ................................................................................................................................ 28

AS 5 Packer .................................................................................................................................. 29

Snapset I Packer ........................................................................................................................... 30

Snapset II Packer .......................................................................................................................... 31

SL Shear Tension Packer .........................................................................................................32-33



Type DL-1 Tandem Tension Packer ............................................................................................ 34

Big Bore Casing Packer ................................................................................................................ 35

AD-1 Tension Packer ..............................................................................................................36-37

GV-Cup Packer ............................................................................................................................ 38

Set Down Isolation Packer ........................................................................................................... 39

Permapak Seal Bore Production Packer........................................................................................ 40

Gas Vent Pumping Packer ............................................................................................................ 41

PBP Bridge Plug .......................................................................................................................... 42

Scab Liner Packer (SLP) .............................................................................................................. 43

Pump-Out Plug ........................................................................................................................... 44

Hydroset II ................................................................................................................................... 45

Permapak Tubing and Packing Accessories .............................................................................46-47

BA Tubing Anchor Catcher ......................................................................................................... 48

Shear & Rotational Safety Joint ................................................................................................... 49

Pump-Out Cementing Sleeve ...................................................................................................... 50

Bit Release .................................................................................................................................... 51

Cement Port Collar & Shifting Tool ............................................................................................ 52

Type A Cementing Shoe Packer Type .......................................................................................... 53

Multi-Stage Cementing Collar ...............................................................................................54-55

Gard Mill-EZ™ Composite Bridge Plug ...................................................................................... 56

Gard Mill-EZ™ Flo-Back Composite Bridge Plug ...................................................................... 57

Casing Chart ................................................................................................................................ 58



Model ‘CRP’ Rotation Set PackerThe CRP packer is a rotation set packer designed to run below a down hole gas separator. It uses a Tubing Anchor Catcher to anchor the packer to the casing. After the packer is set there is no movement to wear out the slips or other parts, allowing it to stay set under the most severe conditions.

Special Features• Short and compact•Inexpensive•Easy to set and release•Tubing can be left in tension, compression or neutral•Built in fluid bypass for running and retrieving

Running and Setting ProcedureMake up packer on top of tubing anchor by holding backup on lower mandrel of packer and wrench on bottom of anchor. Make up Gas Separator up on top of packer, hold backup on top sub of packer and wrench on bottom on gas separator. Make up pump seating nipple in top of gas separator and run in hole slowly to setting depth. Make sure all tubing joints are tight. Rotate the tubing to the left 5 to 7 rounds to set the tubing anchor. The tubing should torque up when the slips contact the casing, continue turning the tubing 3 to 4 rounds to shear the rotational shear screw in the packer and expand the packing elements. Hold torque on tubing while setting down and picking up to be sure the packer and anchor is securely anchored to the casing. Land the tubing with the desired amount of tension.

Releasing Procedure Set 2000 lbs down on anchor and rotate to right until anchor releases.

Casing PackerBase Product

NumberO.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Max I.D. Standard ThreadConnections

4 9.5 - 11.0 3.476 3.548 3.250 1.72 11⁄2 EUE 43840

41⁄2 9.5 - 13.5 3.920 4.090 3.750 2.00 23⁄8 EUE 43845

5 11.5 - 18.0 4.276 4.560 4.125 2.00 23⁄8 EUE 43850

51⁄2 14.0 - 20.0 4.778 5.012 4.640 2.38 27⁄8 EUE 43855

51⁄2 20.0 - 23.0 4.670 4.890 4.500 2.375 27⁄8 EUE 43854

65/8 28.0 - 32.0 5.675 5.791 5.500 2.50 27⁄8 EUE 43865

65/8 20.0 - 24.0 5.921 6.049 5.735 2.50 27⁄8 EUE 43865B

7 20.0 - 29.0 6.184 6.456 5.970 2.50 27⁄8 EUE 43870

Specification Guide

BESTSELLER



ROTO-SET PackerThe ROTO-SET Packer is designed to withstand the cyclic loads placed on the packer in a rod pumping well but may be used in other production packer applications as well.

Applications• Deviated or horizontal wells• Down hole gas separator• Gas lift wells• Plunger lift wells• Pumping below a casing leak• Isolating perforations

Special Features• Right hand rotation only is required to set slips, close bypass and pack off element• May be set with power tongs with no danger of backing off the tubing• After setting there is no movement in setting mechanism to cause wear• Easy to set and space out• Carbide insert slips are standard for better holding• Slips and drag springs have wider setting range to work in most casings weights• Tubing may be landed in tension, compression or neutral• Released by Straight Pull• May be run with an On-Off Tool

Setting ProcedureRun packer in hole using normal speed and caution when running a packer. Lower packer to setting depth and rotate the tubing to the right with power tongs until the slips engage the casing and the tubing torques up. Keep turning the tubing until there is approximately 500 ft lbs torque on the packer. This should take about 8 rounds in most cases. The casing size and weight may cause this to vary slightly. Hold torque and pick up to the desired tension to check spacing, then set weight down to work the torque down to the packer. Pull tension and set down again while holding torque, the release torque and land tubing on the wellhead.

Releasing ProcedurePick up on tubing to shear the releasing pins that are normally set at 30,000 lbs but can be adjusted in the field up to 50,000 lbs. If an On-Off Tool is run above the packer, the tubing can be pulled without pulling the packer. The packer may also be released by left hand rotation if desired.

Specification Guide

NEWright hand

set

Casing Packer Part NumberO.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection

41⁄2 9.5 - 13.5 3.920 4.090 3.750 2.00 23⁄8 EUE WRS45

51⁄2 14.0 - 20.0 4.778 5.012 4.640 2.38 27⁄8 EUE WRS55

51⁄2 20.0 - 23.0 4.670 4.890 4.500 2.38 27⁄8 EUE WRS54

7 20.0 - 29.0 6.184 6.456 5.970 2.50 27⁄8 EUE WRS70



WRL Production PackerThe WRL Production Packer is designed to withstand the cyclic loads placed on the packer in a rod pumping well but may be used in other production packer applications as well.

Applications• Pumping below a casing leak• Isolating perforations• Down hole gas separator• Plunger lift wells• Gas lift wells

Special Features• Rotation only is required to set slips, close bypass and pack off element• After setting there is no movement in setting mechanism to cause wear• Low torque required to pack off elements• Easy to set and space out• Carbide insert slips are standard for better holding• Slips and drag springs have wider setting range to work in most casings weights• Tubing may be landed in tension, compression or neutral• Released by right hand rotation• Emergency shear release

Setting ProcedureRun packer in hole using normal speed and caution when running a packer. Make sure all connections above packer are tightened to the proper torque. Lower packer to setting depth and rotate the tubing to the left until the slips engage the casing and the tubing torques up. Keep turning the tubing until there is approximately 500 ft lbs torque on the packer. This should take about 8 rounds in most cases. The casing size and weight may cause this to vary slightly. Hold torque and pick up to the desired tension to check spacing, then set weight down to work the torque down to the packer. Pull tension and set down again while holding torque, the release torque and land tubing on the wellhead.

Releasing ProcedureRemove tension from the packer and rotate to the right 8 or 10 turns and the packer should be free to move up or down. If the tubing is not turning on bottom, hold torque and work the tubing up and down to find a point where it will rotate. Do not let the tubing turn to the left while pulling out of the hole. Turning the tubing to the right occasionally will keep the packer from setting. The packer also has an emergency shear release that normally is 50,000 lbs but may be adjusted to a lower amount.

Casing Packer Part NumberO.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection

41⁄2 9.5 - 13.5 3.920 4.090 3.750 2.00 23⁄8 EUE WRL45

51⁄2 14.0 - 20.0 4.778 5.012 4.640 2.38 27⁄8 EUE WRL55

51⁄2 20.0 - 23.0 4.670 4.890 4.500 2.375 27⁄8 EUE WRL54

7 20.0 - 29.0 6.184 6.456 5.970 2.50 27⁄8 EUE WRL70

Specification Guide



Type T Squeeze PackerThe Type T Squeeze Packer is a tension set packer that holds pressure above or below. The tool can be set at any depth and is used where insufficient weight is available to set a compression packer. This packer is ideal for squeeze cementing, testing, stimulation and straddle operations using a retrievable bridge plug.

The SC Tension Unloader is generally run above the Type T Packer allowing pressure equalization before releasing the packer. It also provides a bypass when running and retrieving to minimize swabbing of the elements.

The Type T Squeeze Packer emergency release system incorporates a left-hand, high ratio thread. Applying right-hand torque relaxes the packing element and moves the lower cone away from the slips enabling them to retract.

Special Features• Holds pressure from above or below• Safety release allows circulation around the slips• Full opening• Optional setting configuration• Bidirectional slips

Casing PackerPart

NumberO.D. Weight lb/ft Min I.D.

Max I.D. O.D. I.D. Thread Connections

Box up/Pin down

27⁄8 6.16 - 6.48 2.323 2.441 2.250 0.75 3/4 EUE 62025

4 9.5 - 11.0 3.476 3.548 3.250 1.62 23⁄8 EUE 62040

41⁄2 15.1 - 16.6 3.754 3.826 3.562 1.62 23⁄8 EUE 62041

41⁄2 9.5 - 13.5 3.920 4.090 3.750 2.00 23⁄8 EUE 62145

5 13.0 - 18.0 4.276 4.494 4.125 2.00 23⁄8 EUE 62150

5 18.0 - 20.8 4.156 4.276 4.000 2.00 23⁄8 EUE 62152

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.00 23⁄8 EUE 62155

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 62157

65/8 24.0 - 28.0 5.791 5.921 5.625 2.50 27⁄8 EUE 62065

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 62170

75/8 26.4 - 33.7 6.765 6.969 6.500 2.50 27⁄8 EUE 62075

85/8 24.0 - 40.0 7.725 8.097 7.500 2.50 27⁄8 EUE 62085

95/8 43.5 - 53.5 8.535 8.755 8.250 2.50 27⁄8 EUE 62096

95/8 32.3 - 43.5 8.755 9.001 8.500 2.50 27⁄8 EUE 62095

* Other sizes and connections available on request

Specification Guide



Crest III PackerThe Crest III Packer is a weight set service packer for high pressure remedial work, including acidizing, fracturing, squeeze cementing, etc. It will set with minimal tubing manipulation and will withstand differential pressure from above or below. A large integral fluid bypass allows the packer to be run quickly, with minimal chance of swabbing off packing elements or dulling hold down slips. No rotation is required to retrieve, and its equalizing valve opens with the first upward movement. Carbide tipped hold down slips, lower slips, and drag blocks are standard equipment.

Size Casing WeightGage and

Guide RingO.D.

PackingElement

O.D.Packer Bore Connections

(box up/pin down)

31⁄2 7.7 - 9.3 2.810 2.70 1.25 1.900 EU 10Rd

4 9.5 - 11.0 3.300 3.18 1.50 23⁄8 EU 8Rd

41⁄2 9.5 - 13.5 3.750 3.62 1.88 23⁄8 EU 8Rd

5 15.0 - 18.0 4.125 3.94 1.88 23⁄8 EU 8Rd

5 11.5 - 15.0 4.250 4.12 1.88 23⁄8 EU 8Rd

51⁄2 17.0 - 23.0 4.500 4.38 2.00 23⁄8 EU 8Rd

51⁄2 14.0 - 17.0 4.641 4.50 2.00 23⁄8 EU 8Rd

51⁄2 13.0 - 15.5 4.781 4.69 2.00 23⁄8 EU 8Rd

65/8 20.0 - 24.0 5.687 5.56 2.50 27⁄8 EU 8Rd

7 29.0 - 38.0 5.687 5.56 2.50 27⁄8 EU 8Rd

7 23.0 - 29.0 6.000 5.75 2.50 27⁄8 EU 8Rd

7 17.0 - 23.0 6.180 6.12 2.50 27⁄8 EU 8Rd

75/8 43.0 - 47.0 6.180 6.12 2.50 27⁄8 EU 8Rd

75/8 33.0 - 39.0 6.453 6.12 2.50 27⁄8 EU 8Rd

75/8 24.0 - 30.0 6.672 6.50 2.50 27⁄8 EU 8Rd

85/8 40.0 - 49.0 7.312 7.00 3.00 31⁄2 EU 8Rd

85/8 28.0 - 36.0 7.625 7.00 3.00 31⁄2 EU 8Rd

95/8 43.5 - 53.5 8.250 7.94 3.00 31⁄2 EU 8Rd

95/8 32.3 - 43.5 8.500 8.38 3.00 31⁄2 EU 8Rd

Specification Guide



HD Retrievable PackerThe HD Retrievable Packer is a high pressure, full opening, compression set tool for squeeze cementing, acidizing, fracturing and other stimulation procedures. This tool features a pressure-balanced unloader that closes when the packer sets. While pressure aids in maintaining the seal the unloader can be easily opened under high differential pressure. The large internal bypass reduces swabbing when running and retrieving.

Special Features• Large internal bypass• Built in pressure-balanced unloader• 1/4 turn set-straight pick up release (standard)• Equalizing ports directly above elements• Additional J-slot arrangements available

Casing PackerPart

NumberO.D. Weight lb/ft Min I.D.

Max I.D. O.D. I.D. Thread Connections

Box up/Pin down

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.87 23⁄8 EUE 61345

5 11.5 - 15.0 4.408 4.560 4.125 1.87 23⁄8 EUE 61350

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 61356

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.00 23⁄8 EUE 61357

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.37 23⁄8 EUE 61358

51⁄2 9.0 - 13.0 5.044 5.192 4.812 2.50 23⁄8 EUE 61359

65/8 24.0 - 32.0 5.675 5.920 5.500 2.50 27⁄8 EUE 61365

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 61370

7 17.0 - 26.0 6.276 6.538 6.094 2.50 27⁄8 EUE 61372

95/8 43.5 - 53.5 8.535 8.755 8.250 4.00 41⁄2 EUE 61395

95/8 32.0 - 43.5 8.755 9.001 8.500 4.00 41⁄2 EUE 61396

103/4 51.0 - 65.7 9.560 9.850 9.312 4.00 41⁄2 EUE 61310

103/4 32.75 - 45.50 9.950 10.192 9.700 4.00 41⁄2 EUE 61301


Specification Guide



TS Retrievable Bridge PlugThe TS Retrievable Bridge Plug is a high pressure plug for multiple zone and selective single zone operations such as acidizing, fracturing, cementing and testing. It features a large internal bypass to reduce swabbing when running and retrieving. The by-pass valve closes when the plug is set. When un-setting the by-pass valve opens before releasing the upper slips to allow pressure equalization. The by-pass is located directly below the upper slips to help debris wash when the by-pass is open. This tool can be set shallow in unsupported casing to contain pressure while working on wellhead equipment.

Special Features• 1/4 right-hand set and release (standard)• Large bypass• Set shallow or deep• Pressure equalization before release• High pressure rating• Additional J-slot arrangements available

Casing Tool O.D. Part Number

O.D. Weight lb/ft Min I.D. Max I.D.

41⁄2 15.1 - 16.6 3.754 3.826 3.65 72541

41⁄2 9.5 - 13.5 3.920 4.090 3.750 72545

51⁄2 9.0 - 13.0 5.044 5.192 4.812 72554

51⁄2 13.0 - 20.0 4.778 5.004 4.625 72555

51⁄2 20.0 - 23.0 4.670 4.778 4.500 72557

65/8 24.0 - 32.0 5.675 5.920 5.500 72565

7 20.0 - 26.0 6.276 6.456 6.000 72570-G6

7 26.0 - 32.0 6.094 6.276 5.875 72471-G6

75/8 24.0 - 29.7 6.875 7.025 6.672 72475

85/8 24.0 - 40.0 7.725 8.097 7.500 72485

95/8 43.5 - 53.5 8.535 8.755 8.250 72596

95/8 32.3 - 43.5 8.755 9.001 8.500 72595


Specification Guide



WLTC Retrievable Bridge PlugThe WLTC is designed to perform all tasks normally required of a tubing run packer type bridge plug, but be quickly converted to run and set on wire-line. It is designed to be rugged and compact (the 41⁄2” size is only 63 inches long). When run on tubing, the WLTC can be set deep or shallow because the packing element system can be energized with compression or tension. This bridge plug will withstand high differential pressures from above or below, while its internal bypass valve is easily opened, to equalize fully prior to release.

Activated slips are always on the low-pressure side with the WLTC design, insuring that a tight pack-off is maintained. When run on tubing, a circulation passage through the tool allows fluid to bypass internally, reducing swabbing. When set, this passage allows effective washing of sand and debris above the elements, assuring easy release and retrieval. Standard equipment on the WLTC Bridge Plug includes tungsten carbide tipped slips and drag blocks, which are long-lasting and eliminate problems setting in the hardest casings.

A spring-loaded retrieving head is used to run (tubing set) and retrieve (tubing or wire-line set) the WLTC Bridge Plug. This helps prevent disconnecting the tool inadvertently. Sealer ball catcher assemblies are available.

Casing Tool O.D.

Size Weight lb/ft

27⁄8 8.6 - 8.7 2.125

27⁄8 6.4 - 6.5 2.300

31⁄2 9.2 - 10.2 2.781

31⁄2 7.7 - 9.3 2.844

41⁄2 13.5 - 16.6 3.640

41⁄2 9.5 - 13.5 3.750

5 15.0 - 18.0 4.125

5 11.5 - 15.0 4.250

51⁄2 17.0 - 23.0 4.500

51⁄2 14.0 - 20.0 4.641

51⁄2 13.0 - 15.5 4.781

65/8 24.0 - 32.0 5.500

65/8 20.0 - 24.0 5.750

7 32.0 - 38.0 5.750

7 23.0 - 29.0 5.970

7 17.0 - 26.0 6.078

*specifications for larger sizes are available upon request

Specification Guide



Type C Perforation Wash ToolThe Type C Perforation Wash Tool is for washing or acidizing perforations in casing and sand screens. It is also used for checking non-perforations to verify injection rates and penetration or for opening voids behind the casing for more effective gravel pack operations. The straddle interval is easily field converted from one foot to any distance by simply adding tubing between the center cups.

Special Features• Straddle spacing easily field adjusted• Reverse circulate without manipulation• No ball and seat required

Pipe Size Maximum Metal O.D. Thread Connection Part Number

31⁄2 2.81 1.900 NU 460354 3.25 1.900 NU 46040

41⁄2 3.69 1.900 NU 4604551⁄2 4.63 27⁄8 EUE 460557 6.00 31⁄2 EUE 46070

75/8 6.62 31⁄2 EUE 4607595/8 8.45 31⁄2 EUE 46095103/4 9.71 31⁄2 EUE 46010


Specification Guide



StradasnapThe Stradasnap Packer is a tool used for selectively acidizing short intervals of casing perforations to evenly break down the formation. The span covered is determined by the spacing between the two sets of packing elements and is adjustable to any distance down to eighteen (18) inches.

The bottom of the packer is plugged by using an Equalizing Standing Valve. A Spot Control Valve should be run above the packer to control the tubing hydrostatic pressure across the perforations and contain the acid in the tubing when moving the packer to another perforation.

After locating the packer across the lower most perforation, the packer is set and the perforation is treated. Straight pick up of the tubing releases the packer to be moved up to the next perforation. When retrieving the packer, tubing fluid is dumped through the ports between the packing elements to prevent pulling a wet string.

Special Features• Adjustable spacing between packing elements using PUP Joints• Easy to set and release• Pressure equalization and by-pass

Casing Packer Base Product NumberO.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connections

Box up/Pin down

41⁄2 15.1 3.826 3.826 3.656 1.94 23⁄8 EUE 64044

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 64045

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 64055

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.37 27⁄8 EUE 64556

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 64070

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 64072

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 64075

75/8 33.7 - 39.0 6.625 6.765 6.453 2.50 27⁄8 EUE 64576


Specification Guide



Type H Tension PackerThe Type H Tension Packer is for use in water flood, injection or producing wells. This tension packer has a built in safety system to eliminate problems should conventional retrieval methods fail. Right hand rotation releases the first safety joint allowing the slips to pull off the cone and release the packer. Should the packer fail to release, a second safety joint can be broken to release the packer. This safety feature allows for circulation down the tubing to remove debris. In addition our tension packer is available for open hole applications and incorporates dual elongated packing elements and deep wickered slips for better bite into the formation.

Special Features• Full opening• Built-in safety joint• Stainless steel drag springs• Available to set in open hole• Long packing element to give maximum sealing area

Casing PackerPart

NumberO.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connections Box up/Pin down

27⁄8 6.4 - 6.5 2.375 2.441 2.250 0.75 1.315 EUE 40525

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 40545

5 11.5 - 15.0 4.408 4.560 4.125 1.94 23⁄8 EUE 40550

5 15.0 - 20.8 4.156 4.408 4.000 1.94 23⁄8 EUE 40551

51⁄2 13.0 - 20.0 4.778 5.044 4.625 1.94 23⁄8 EUE 40555

51⁄2 13.0 - 20.0 4.778 5.044 4.625 2.44 27⁄8 EUE 40556

51⁄2 20.0 - 23.0 4.670 4.778 4.500 1.94 23⁄8 EUE 40557

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.44 27⁄8 EUE 40558

6 15.0 - 20.0 5.352 5.524 5.188 2.44 27⁄8 EUE 40560

65/8 24.0 - 32.0 5.625 5.921 5.500 2.44 27⁄8 EUE 40565

65/8 20.0 - 24.0 5.921 6.049 5.750 2.44 27⁄8 EUE 40568

7 17.0 - 29.0 6.184 6.538 6.000 2.44 27⁄8 EUE 40570

7 17.0 - 29.0 6.184 6.538 6.000 3.00 31⁄2 EUE 40573

75/8 20.0 - 33.7 6.765 7.125 6.625 2.44 27⁄8 EUE 40575

75/8 20.0 - 33.7 6.765 7.125 6.625 3.00 31⁄2 EUE 10576

85/8 24.0 - 40.0 7.725 8.097 7.500 2.50 27⁄8 EUE 40585

85/8 24.0 - 40.0 7.725 8.097 7.500 3.00 31⁄2 EUE 40587

95/8 29.3 - 43.5 8.755 9.063 8.500 2.50 27⁄8 EUE 40595

95/8 29.3 - 43.5 8.755 9.063 8.500 3.00 31⁄2 EUE 404597

103/4 40.0 - 55.5 9.760 10.050 9.500 3.00 31⁄2 EUE 40510

103/4 40.0 - 55.5 9.760 10.050 9.500 2.50 27⁄8 EUE 40511

133⁄8 48.0 - 72.0 12.347 12.715 12.000 3.00 31⁄2 EUE 40513


Specification Guide



PCR Cement RetainerThe PCR Cement Retainer is a modular designed drillable cement retainer that is used for acidizing, fracturing or cementing operations.

Special Features• Simple surface controlled valve• Allows pressure testing before squeeze• Valve automatically closes when the stinger is removed, locking in the squeeze pressure• Valve protects sensitive zones in low fluid wells• Simple conversion to bridge plug• Specify mechanical or wireline set• Components rotationally locked for easy drillout

Casing Tool O.D.

Base Product NumberO.D. Weight lb/ft Min I.D. Max I.D.

41⁄2 9.5 - 15.1 3.826 4.090 3.593 43PCR

5 11.5 - 18.0 4.276 4.560 3.937 44PCR

51⁄2 13.0 - 23.0 4.670 5.044 4.312 45PCR

65/8 17.0 - 34.5 5.575 6.135 5.375 46PCR

7 32.0 - 44.0 5.720 6.094 5.375 47PCR

7 17.0 - 35.0 6.004 6.538 5.688 47PCR

75/8 20.0 - 39.0 6.625 7.125 6.312 48PCR

85/8 24.0 - 52.0 7.435 8.097 7.125 49PCR

95/8 29.3 - 61.1 8.375 9.063 8.125 51PCR

103/4 32.75 - 60.7 9.660 10.192 9.437 53PCR

113/4 38.0 - 60.0 10.772 11.150 10.437 54PCR

133⁄8 48.0 - 72.0 12.347 12.715 12.000 55PCR

16 65.0 - 128.0 14.438 15.250 14.125 57PCR

Specification Guide



Lok-Set PackerThe Lok-Set is a compression set, retrievable packer that allows the tubing to be left in a tension, compression, or neutral condition. Application is mostly production, injection and zone isolation operations.

Special Features• Internal by-pass• Opposed dovetail slips for positive set• Holds pressure from above or below• Can leave tubing in a tension, compression, or neutral condition• Right-hand rotation sets and releases the packer• Retracted dovetail slips• Converts to mechanical bridge plug with the addition of a valve• Optional packing element systems• Large bore available (45LLS and/or 47LLS)• Parts interchangeable with other manufacturers

Setting ProcedureHang the Packer to completely stretch it out before starting in the hole. Immediately prior to running in, rotate the drag block housing sub-assembly several turns to the left to make sure the segments are functioning properly. Do not rotate the drag block housing sub-assembly to the right as this will bind the control segments and prevent them from moving after reaching setting depth.

Upon reaching setting depth, slowly lower the packer while rotating the tubing (approximately two turns right at the tool) until the packer takes weight. Set-down a minimum of 6,000 lb. to initially set the upper slips. Lowering of the tool must take place while rotating for the tool to set properly.

To fully engage the lower slips, apply an upstrain (10,000 to 20,000 lb. for sizes 41⁄2 thru 51⁄2 and 7”, and 20,000 to 30,000 lb. for sizes 85/8 and 95/8) against the tool. When the tubing is to be landed in tension, a strain greater than the landing strain should be applied during the setting operation.

To completely set the upper slips and pack-off the packing element system apply set-down weight (6,000 lb. for sizes 41⁄2 thru 51⁄2, 10,000 lb. for size 7”, and 15,000 lb. for 85/8 and 95/8). If sufficient set-down weight is not available, such as in very shallow wells, the tool can be set and packed-off by left-hand rotation or spudding.

The tubing may now be hung in tension, compression or neutral.

Releasing ProcedureApply an upstrain of approximately 3,000 to 6,000 lb. and rotate the tubing (four to eight turns at the tool) to the right until the tool moves up the hole. When releasing the packer with pressure in favor of the tubing, rotate tubing to the right slowly enough to equalize before the lower slips disengage. Continue to rotate to the right several turns while moving up the hole to be certain the slips are fully retracted.



Casing PackerBase Product Number

O.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Standard ThreadConnections

41⁄2 11.6 - 13.5 3.920 4.000 3.771 23⁄8 EU 8RD 43LS-A2

41⁄2 9.5 - 10.5 4.052 4.090 3.771 23⁄8 EU 8RD 43LS-A4

5 15.0 - 18.0 4.250 4.408 4.125 23⁄8 EU 8RD 43LS-B

5 11.5 - 15.0 4.408 4.560 4.250 23⁄8 EU 8RD 43LS-C

51⁄2 26.0 4.408 4.560 4.250 23⁄8 EU 8RD 43LS-C

51⁄2 20.0 - 23.0 4.625 4.777 4.500 27⁄8 EU 8RD 45LLS-A2 X 2.38

51⁄2 20.0 - 23.0 4.670 4.778 4.500 23⁄8 EU 8RD 45LS-A2

51⁄2 17.0 - 20.0 4.778 4.892 4.641 27⁄8 EU 8RD 45LLS-A4 X 2.38

51⁄2 15.5 - 20.0 4.778 4.950 4.641 23⁄8 EU 8RD 45LS-A4

51⁄2 13.0 - 15.5 4.950 5.044 4.781 27⁄8 EU 8RD 45LLS-A4 X 2.38

51⁄2 13.0 - 15.5 4.950 5.044 4.781 23⁄8 EU 8RD 45LS-B

53/4 22.5 4.893 5.044 4.781 27⁄8 EU 8RD 45LLS-B X 2.38

6 26.0 4.893 5.044 4.781 27⁄8 EU 8RD 45LLS-B X 2.38

6 26.0 4.950 5.190 4.781 23⁄8 EU 8RD 45LS-B

65/8 20.0 5.989 6.094 5.812 31⁄2 EU 8RD 47LLS-A4 X 3.00

65/8 17.0 6.136 6.276 5.968 31⁄2 EU 8RD 47LLS-B4 X 3.00

65/8 24.0 5.830 5.937 5.656 27⁄8 EU 8RD 47LS-A2

65/8 17.0 - 20.0 6.049 6.135 5.812 27⁄8 EU 8RD 47LS-A4

7 38.0 5.830 5.937 5.656 27⁄8 EU 8RD 47LS-A2

7 32.0 - 35.0 6.004 6.094 5.812 31⁄2 EU 8RD 47LLS-A4 X 3.00

7 32.0 - 35.0 6.004 6.094 5.812 27⁄8 EU 8RD 47LS-A4

7 26.0 - 29.0 6.184 6.276 5.968 31⁄2 EU 8RD 47LLS-B2 X 3.00

7 26.0 - 29.0 6.184 6.276 5.968 27⁄8 EU 8RD 47LS-B2

7 20.0 - 26.0 6.276 6.456 6.078 31⁄2 EU 8RD 47LLS-B4 X 3.00

7 23.0 - 26.0 6.276 6.366 6.078 27⁄8 EU 8RD 47LS-B4

7 17.0 - 20.0 6.456 6.538 6.266 31⁄2 EU 8RD 47LLS-C2 X 3.00

7 17.0 - 20.0 6.456 6.538 6.266 27⁄8 EU 8RD 47LS-C2

75/8 33.7 - 39.0 6.625 6.765 6.453 27⁄8 EU 8RD 47LS-C4

75/8 24.0 - 29.7 6.875 7.025 6.672 27⁄8 EU 8RD 47LS-D2

75/8 20.0 - 24.0 7.025 7.125 6.812 27⁄8 EU 8RD 47LS-D4

85/8 44.0 - 49.0 7.511 7.625 7.312 4 NU 8RD 49LS-A2

85/8 32.0 - 40.0 7.725 7.921 7.531 4 NU 8RD 49LS-A4

85/8 24.0 - 28.0 8.017 8.191 7.781 4 NU 8RD 49LS-B

95/8 47.0 - 53.5 8.535 8.681 8.218 4 NU 8RD 51LS-A2

95/8 40.0 - 47.0 8.681 8.835 8.437 4 NU 8RD 51LS-A4

95/8 29.3 - 36.0 8.921 9.063 8.593 4 NU 8RD 51LS-B

Specification Guide



ASI-X PackerThe ASI-X is our most versatile mechanically set, retrievable packer. It may be used in any production application and is best suited for treating, testing and injecting in shallow to deep pumping or flowing wells. It features a large internal bypass to reduce swabbing when running or retrieving. It can be applied in tension or compression depending on well conditions and the required applications. When the packer is set the bypass closes and when retrieving the bypass opens before releasing the upper slips to allow pressure equalization. The J-Slot design allows easy setting and releasing (1/4 turn right-hand set and righthand release). Also available in a 10K version to withstand pressures up to 10,000 PSI and in situations where it is preferable to leave the tool in the well.

Special Features• Bypass below upper slips to wash debris when valve is opened• Bypass is opened before upper slips are released• Can be set with tension for shallow well• Can be left in tension, compression or neutral• 1/4 turn right-hand set, right-hand release• Additional J-Slot arrangement available



Casing PackerPart


27⁄8 6.4 - 6.5 2.441 2.441 2.250 0.63 1.050 EUE 6032531⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 6033531⁄2 12.95 2.750 2.750 2.562 1.00 1.660 EUE 603364 9.5 - 11.0 3.476 3.548 3.250 1.50 1.900 EUE 603404 12.95 3.340 3.340 3.187 1.50 1.900 EUE 60341

41⁄2 18.8 3.640 3.640 3.437 1.50 1.900 EUE 6034241⁄2 15.1 - 16.9 3.740 3.826 3.594 1.50 1.900 EUE 6034341⁄2 15.1 3.826 3.826 3.656 1.94 23⁄8 EUE 6034441⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 6034541⁄2 15.1 3.826 3.826 3.641 1.94 23⁄8 EUE 603465 11.5 - 15.0 4.408 4.560 4.125 1.94 23⁄8 EUE 603505 18.0 - 20.8 4.156 4.276 4.000 1.94 23⁄8 EUE 60352

51⁄2 14.0 - 20.0 4.778 5.044 4.625 2.00 23⁄8 EUE 6035551⁄2 15.5 - 17.0 4.892 4.950 4.625 2.38 27⁄8 EUE 6035651⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 6035751⁄2 13.0 - 14.0 5.012 5.044 4.813 2.38 27⁄8 EUE 6035851⁄2 20.0 - 23.0 4.670 4.778 4.500 2.38 27⁄8 EUE 603596 17.0 - 20.0 5.352 5.450 5.188 2.38 27⁄8 EUE 603606 14.0 - 16.0 5.500 5.552 5.188 2.38 27⁄8 EUE 60361

65/8 24.0 - 32.0 5.675 5.920 5.500 2.50 27⁄8 EUE 6036565/8 32.0 - 34.5 5.575 5.675 5.312 2.50 27⁄8 EUE 6036665/8 17.0 - 24.0 5.921 6.135 5.750 2.50 27⁄8 EUE 6036765/8 20.0 - 24.0 5.921 6.049 5.750 3.00 31⁄2 EUE 6036865/8 20.0 6.049 6.049 5.812 3.00 31⁄2 EUE 603697 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 603707 29.0 - 35.0 6.004 6.184 5.812 2.50 27⁄8 EUE 603717 17.0 - 26.0 6.276 6.538 6.062* 2.50 27⁄8 EUE 603727 26.0 - 32.0 6.094 6.276 5.875 3.00 31⁄2 EUE 603737 17.0 - 26.0 6.276 6.538 6.125* 3.00 31⁄2 EUE 60374

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 6037575/8 33.7 - 39.0 6.625 6.765 6.453 2.50 27⁄8 EUE 6037675/8 33.7 - 39.0 6.625 6.765 6.453 3.00 31⁄2 EUE 6037775/8 24.0 - 29.7 6.875 7.025 6.672 3.00 31⁄2 EUE 6037885/8 28.0 - 40.0 7.725 8.017 7.500 4.00 41⁄2 EUE 6038285/8 24.0 - 40.0 7.725 8.097 7.500 2.50 27⁄8 EUE 6038585/8 44.0 - 49.0 7.511 7.625 7.312 2.50 27⁄8 EUE 6038685/8 28.0 - 40.0 7.725 8.017 7.500 3.00 31⁄2 EUE 6038795/8 43.5 - 53.5 8.535 8.755 8.250 4.00 41⁄2 EUE 6039595/8 32.3 - 43.5 8.755 9.001 8.500 4.00 41⁄2 EUE 60396103/4 32.75 - 45.5 9.560 10.192 9.700 4.00 41⁄2 EUE 60301103/4 45.5 - 51.0 9.850 9.95 9.625 4.00 41⁄2 EUE 60302103/4 51.0 - 65.7 9.560 9.850 9.312 4.00 41⁄2 EUE 60310113/4 42.0 - 65.0 10.682 11.084 10.438 4.00 41⁄2 EUE 60311133⁄8 54.5 - 77.0 12.275 12.615 12.000 4.00 41⁄2 EUE 60313

* Maximum O.D. is across retracted drag blocks. ** Other sizes and connections available on request.

Specification Guide



VSI-XW Wireline SetProduction PackerThe VSI-XW Single String Double Grip Production Packer is one of the most versatile packers on the market. It is a modification of the ASI-X packer with the advantage of being able to set on electric line or hydraulically.

An On-Off Tool Stinger with Wireline Plug installed can be attached to the top of the VSI-XW Packer which can then be lubricated in the hole and set under pressure. Once set, casing pressure can be bled off and the tubing with an On-Off Tool Overshot can be run and latched onto the packer. The Wireline Plug can then be removed.

The VSI-XW Packer converts to a mechanically set ASI-X by removing the shear screws and installing drag blocks. This packer sets with 1/4 right-hand rotation; releases with 1/4 right-hand rotation and can be left in tension, compression or neutral.

Special Features• Wireline or Tubing set• Sequential releaser upper slip system• Bypass valve opens before upper slips are released• 1/4 turn to set, 1/4 turn to release (ASI-X version)• Available in shear release



Casing PackerPart


27⁄8 6.4 - 6.5 2.441 2.441 2.250 0.63 1.050 EUE 6032531⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 6033531⁄2 12.95 2.750 2.750 2.562 1.00 1.660 EUE 603364 9.5 - 11.0 3.476 3.548 3.250 1.50 1.900 EUE 603404 12.95 3.340 3.340 3.187 1.50 1.900 EUE 60341

41⁄2 18.8 3.640 3.640 3.437 1.50 1.900 EUE 6034241⁄2 15.1 - 16.9 3.740 3.826 3.594 1.50 1.900 EUE 6034341⁄2 15.1 3.826 3.826 3.656 1.94 23⁄8 EUE 6034441⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 6034541⁄2 15.1 3.826 3.826 3.641 1.94 23⁄8 EUE 603465 11.5 - 15.0 4.408 4.560 4.125 1.94 23⁄8 EUE 603505 18.0 - 20.8 4.156 4.276 4.000 1.94 23⁄8 EUE 60352

51⁄2 14.0 - 20.0 4.778 5.044 4.625 2.00 23⁄8 EUE 6035551⁄2 15.5 - 17.0 4.892 4.950 4.625 2.38 27⁄8 EUE 6035651⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 6035751⁄2 13.0 - 14.0 5.012 5.044 4.813 2.38 27⁄8 EUE 6035851⁄2 20.0 - 23.0 4.670 4.778 4.500 2.38 27⁄8 EUE 603596 17.0 - 20.0 5.352 5.450 5.188 2.38 27⁄8 EUE 603606 14.0 - 16.0 5.500 5.552 5.188 2.38 27⁄8 EUE 60361

65/8 24.0 - 32.0 5.675 5.920 5.500 2.50 27⁄8 EUE 6036565/8 32.0 - 34.5 5.575 5.675 5.312 2.50 27⁄8 EUE 6036665/8 17.0 - 24.0 5.921 6.135 5.750 2.50 27⁄8 EUE 6036765/8 20.0 - 24.0 5.921 6.049 5.750 3.00 31⁄2 EUE 6036865/8 20.0 6.049 6.049 5.812 3.00 31⁄2 EUE 603697 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 603707 29.0 - 35.0 6.004 6.184 5.812 2.50 27⁄8 EUE 603717 26.0 - 32.0 6.094 6.276 5.875 3.00 31⁄2 EUE 60373

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 6037575/8 33.7 - 39.0 6.625 6.765 6.453 2.50 27⁄8 EUE 6037675/8 33.7 - 39.0 6.625 6.765 6.453 3.00 31⁄2 EUE 6037775/8 24.0 - 29.7 6.875 7.025 6.672 3.00 31⁄2 EUE 6037885/8 28.0 - 40.0 7.725 8.017 7.500 4.00 41⁄2 EUE 6038285/8 24.0 - 40.0 7.725 8.097 7.500 2.50 27⁄8 EUE 6038585/8 44.0 - 49.0 7.511 7.625 7.312 2.50 27⁄8 EUE 6038685/8 28.0 - 40.0 7.725 8.017 7.500 3.00 31⁄2 EUE 6038795/8 43.5 - 53.5 8.535 8.755 8.250 4.00 41⁄2 EUE 6039595/8 32.3 - 43.5 8.755 9.001 8.500 4.00 41⁄2 EUE 60396103/4 32.75 - 45.5 9.560 10.192 9.700 4.00 41⁄2 EUE 60301103/4 45.5 - 51 9.850 9.950 9.625 4.00 41⁄2 EUE 60302103/4 51.0 - 65.7 9.560 9.850 9.312 4.00 41⁄2 EUE 60310113/4 42.0 - 65.0 10.682 11.084 10.438 4.00 41⁄2 EUE 60311133⁄8 54.5 - 77.0 12.275 12.615 12.000 4.00 41⁄2 EUE 60313

* Other sizes and connections available on request.

Specification Guide



R-3 Double Grip PackerThe R-3 is a double grip, compression set, retrievable packer that is mostly used in production, stimulation and testing operations.

Special Features• Differential lock helps keep the by-pass closed and locked to the mandrel during high-pressure operations• Automatically returns to run-in position when moved up the hole• Hydraulic hold-down for differential pressure from below• Long stroke mandrel simplifies circulation of fluids without releasing the packer• Large by-pass allows speedy equalization of fluids• Rocker type slips• Standard right-hand set, optional left-hand set• Large bore available (45RDL)• Parts interchangeable with other manufacturers

Setting ProcedureThe R-3 Double Grip Packer is run in with the by-pass valve in the open position to permit free circulation both through and around the packer. The packer should be run one foot below setting depth. To set the R-3, pick up the tubing to the desired setting position, rotate to the right, and then slack-off. The J-pin will move clear of the J-slot and the cone will move under the slips. Application of set-down weight, for standard packing element system (7,000 lb. for sizes 41⁄2 thru 51⁄2, 5,000 lb. for size 51⁄2 x 27⁄8, 9,000 lb. for size 7”, 11,000 lb. for size 85/8, and 15,000 lb. for size 95/8) closes and seals the bypass valve, sets the slips, and packs-off the packing elements. The formation below the packer, which is now completely isolated from the annulus above, is accessible only through the tubing string.

Releasing ProcedureTo release the packer, raise the tubing string the full length of the packer. When the J-pin of the bottom sub engages the slip stop ring (jay housing), the J-pin automatically moves into the running position. This allows the tool to be moved up or down the wellbore as necessary. When the tubing is raised to release the packer, the by-pass valve opens to permit circulation through and around the packer.



Casing PackerBase Product Number

O.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Standard ThreadConnections

41⁄2 9.5 - 13.5 3.920 4.090 3.771 23⁄8 EU 8RD 43RD-A

5 15.0 - 18.0 4.250 4.408 4.125 23⁄8 EU 8RD 43RD-B

5 11.5 - 15.0 4.408 4.560 4.250 23⁄8 EU 8RD 43RD-C

51⁄2 26.0 4.408 4.560 4.250 23⁄8 EU 8RD 43RD-C

51⁄2 20.0 - 28.4 4.440 4.778 4.500 27⁄8 EU 8RD 45RDL-A2 X 2.38

51⁄2 20.0 - 23.0 4.670 4.778 4.500 23⁄8 EU 8RD 45RD-A2

51⁄2 15.5 - 20.0 4.778 4.950 4.641 23⁄8 EU 8RD 45RD-A4

51⁄2 13.0 - 15.5 4.950 5.044 4.781 27⁄8 EU 8RD 45RDL-A4 X 2.38

51⁄2 13.0 - 15.5 4.950 5.044 4.781 23⁄8 EU 8RD 45RD-B

53/4 22.5 4.893 5.044 4.781 27⁄8 EU 8RD 45RDL-B X 2.38

53/4 22.5 4.950 5.190 4.781 23⁄8 EU 8RD 45RD-B

6 26.0 4.893 5.044 4.781 27⁄8 EU 8RD 45RDL-B X 2.38

6 26.0 4.950 5.190 4.781 23⁄8 EU 8RD 45RD-B

7 24.0 5.830 5.937 5.656 27⁄8 EU 8RD 47RD-A2

7 17.0 - 20.0 6.456 6.538 5.812 27⁄8 EU 8RD 47RD-A4

7 38.0 5.830 5.937 5.656 27⁄8 EU 8RD 47RD-A2

7 32.0 - 35.0 6.004 6.094 5.812 27⁄8 EU 8RD 47RD-A4

7 26.0 - 29.0 6.184 6.276 5.968 27⁄8 EU 8RD 47RD-B2

7 20.0 - 26.0 6.276 6.456 6.078 27⁄8 EU 8RD 47RD-B4

7 17.0 - 20.0 6.456 6.538 6.266 27⁄8 EU 8RD 47RD-C2

75/8 33.7 - 39.0 6.625 6.765 6.453 27⁄8 EU 8RD 47RD-C4

75/8 24.0 - 29.7 6.875 7.025 6.672 27⁄8 EU 8RD 47RD-D2

75/8 20.0 - 24.0 7.025 7.125 6.812 27⁄8 EU 8RD 47RD-D4

85/8 44.0 - 49.0 7.511 7.625 7.312 31⁄2 EU 8RD 49RD-A2

95/8 47.0 - 53.5 8.535 8.681 8.218 31⁄2 EU 8RD 51RD-A2

95/8 40.0 - 47.0 8.681 8.835 8.437 31⁄2 EU 8RD 51RD-A4

95/8 29.3 - 36.0 8.921 9.063 8.593 31⁄2 EU 8RD 51RD-B

Specification Guide



T-2 On-Off ToolThe Type T-2 On-Off Tool is a tubing seal receptacle allowing isolation of a lower zone using a wireline blanking plug. The tubing string can then be removed from the well. When re-run, the tubing string automatically re-engages to the stinger, and the blanking plug can be retrieved by wireline.

The T-2 runs above an ASI-X, VSI-XW or Permanent Packer with latch stinger.

Special Features• Blanking plug seats in top of stinger to prevent debris build-up• Bonded seal allows disconnects and reconnects• Right or left hand release• Milling shoe allows rotation through debris

Casing/Tubing Size Tool O.D. Thread Connection Box up/Pin down

27⁄8 2.250 1.900 NU31⁄2 2.750 1.900 EUE4 3.250 1.900 EUE4 3.250 23⁄8 EUE

41⁄2 3.750 23⁄8 EUE51⁄2 4.500 23⁄8 EUE51⁄2 4.500 27⁄8 EUE65/8 5.500 23⁄8 EUE65/8 5.500 27⁄8 EUE7 5.875 23⁄8 EUE7 5.875 27⁄8 EUE7 5.875 31⁄2 EUE

75/8 6.375 23⁄8 EUE75/8 6.375 27⁄8 EUE75/8 6.375 31⁄2 EUE75/8 6.375 41⁄2 EUE85/8 7.500 23⁄8 EUE85/8 7.500 27⁄8 EUE85/8 7.500 31⁄2 EUE85/8 7.500 41⁄2 EUE95/8 8.250 23⁄8 EUE95/8 8.250 27⁄8 EUE95/8 8.250 31⁄2 EUE95/8 8.250 41⁄2 EUE103/4 9.000 23⁄8 EUE103/4 9.000 27⁄8 EUE103/4 9.000 31⁄2 EUE103/4 9.000 41⁄2 EUE113/4 10.000 23⁄8 EUE113/4 10.000 27⁄8 EUE113/4 10.000 31⁄2 EUE113/4 10.000 41⁄2 EUE


Specification Guide



ASII PackerThe ASII Packer is a double grip, compression set tool ideally suited for treating, testing and production applications. The ASII features a large bypass area to prevent swabbing when running or retrieving. Once the tool is set, pressure from above or below acts down on the valve maintaining the seal and preventing upward movement of the tubing. Releasing the valve allows debris to be washed from the upper slips.

Special Features• Large internal bypass• Mechanical slips vs. hydraulic buttons• Differential pressure holds valve closed• Additional J-slot arrangements available

Casing PackerPart

NumberO.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection Box up/Pin down

27⁄8 6.4 - 6.5 2.441 2.441 2.250 0.63 1.050 EUE 61025

31⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 61135

4 9.5 - 11.6 3.428 3.548 3.250 1.50 1.900 EUE 61140

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 61145

5 11.5 - 18.0 4.276 4.560 4.125 1.94 23⁄8 EUE 61150

5 18.0 - 21.4 4.126 4.276 4.000 1.94 23⁄8 EUE 61152

51⁄2 14.0 - 17.0 4.892 5.012 4.625 2.00 23⁄8 EUE 61155

51⁄2 15.5 - 17.0 4.892 4.950 4.625 2.37 27⁄8 EUE 61156

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 27⁄8 EUE 61157

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.37 27⁄8 EUE 61159

65/8 24.0 - 32.0 5.675 5.920 5.500 2.50 27⁄8 EUE 61165

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 61170

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 61172

75/8 33.7 - 39.0 6.625 6.765 6.453 3.00 31⁄2 EUE 61077


Specification Guide



ASIII PackerThe ASIII Packer is a single grip packer with no upper hold down for use where no differential pressure from below is present. From the packing elements down, the ASIII operates identically to the ASII. The ASII also features a large bypass area to prevent swabbing when running or retrieving. The ASIII is ideal for isolating casing holes or perforations when used as the lower packer in conjunction with the Snapset as the upper packer.

Special Features• Large internal bypass• Optional setting bottoms• 1/4 turn set/straight pick up release• Additional J-slot arrangements available

Casing PackerPart

NumberO.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Max I.D. Thread Connection Box up/Pin down

31⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 63135

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.87 23⁄8 EUE 63145

51⁄2 14.0 - 20.0 4.778 5.012 4.625 1.94 23⁄8 EUE 63155

51⁄2 15.5 - 17.0 4.892 4.950 4.625 2.38 27⁄8 EUE 63156

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 63157

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.38 27⁄8 EUE 63158

65/8 17.0 - 24.0 5.920 6.135 5.750 2.50 27⁄8 EUE 63165

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 63170

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 63172

7 26.0 - 32.0 6.094 6.276 5.875 3.00 31⁄2 EUE 63173

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 63175

95/8 43.5 - 53.5 8.535 8.755 8.250 2.50 27⁄8 EUE 63198


Specification Guide



AS-5 PackerThe AS-5 Packer is a compression set tool with a J-slot to control pack-off. It is run above other packers such as the ASIII to selectively treat, produce or inject in multiple zone completions. It is also used to isolate casing hole perforations. The AS-5 features a large bypass area to prevent swabbing when running and retrieving. Releasing the valve allows debris to be washed from the upper slips.

Special Features• Large internal bypass• Mechanical slips vs. hydraulic buttons• Additional J-slot arrangements available

Casing PackerPart


41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.937 23⁄8 EUE 60845

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.375 27⁄8 EUE 60856

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.000 23⁄8 EUE 60857

7 26.0 - 32.0 6.094 6.276 5.875 2.500 27⁄8 EUE 60870

7 17.0 - 26.0 6.276 6.538 6.000 2.500 27⁄8 EUE 60872

7 17.0 - 26.0 6.276 6.538 6.000 3.000 31⁄2 EUE 60874


Specification Guide



Snapset I PackerThe Snapset I Packer is a compression set tool requiring only straight set down weight to pack-off. It is run above other packers such as the ASIX, ASII or ASIII for selective production to isolate casing holes and perforations. This packer has no upper or lower slips and should be used only where intermediate differential pressures from below are expected. The Snapset has an internal latch to prevent the packer from presetting when running down the hole. When releasing, the latch re-engages to allow movement down hole.

Special Features• Large internal bypass• Set down to pack off, pick up to release• Compact design

Casing PackerPart


31⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 63535

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 63545

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.00 23⁄8 EUE 63555

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.38 27⁄8 EUE 63556

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 63557

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.37 27⁄8 EUE 63558

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 63570

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 63572

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 63575


Specification Guide



Snapset II PackerThe Snapset II Packer is a compression set tool requiring only straight set down weight to pack-off. It is run above other packers such as the ASIII to selectively treat, produce or inject in multiple zone completions. It is also used to isolate casing hole perforations. The Snapset II features a large bypass area to prevent swabbing when running and retrieving. Once the tool is set, pressure from above or below acts down on the valve maintaining the seal and preventing upward movement of the tubing. Releasing the valve allows debris to be washed from the upper slips. This packer is also equipped with an internal latch to prevent presetting when running. When releasing, the latch re-engages to allow movement down hole.

Special Features• Large internal bypass• Mechanical slips vs. hydraulic buttons• Differential pressure holds valve closed• Set down to pack off, pick up to release

Casing PackerPart


31⁄2 7.7 - 10.2 2.922 3.068 2.781 1.25 1.900 NU 63635

41⁄2 15.1 3.826 3.826 3.656 1.94 23⁄8 EUE 63644

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 63645

5 18.0 - 21.0 4.154 4.276 4.000 1.94 23⁄8 EUE 63652

51⁄2 14.0 - 20.0 4.778 5.012 4.625 2.00 23⁄8 EUE 63655

51⁄2 14.0 - 20.0 4.670 4.778 4.625 2.38 27⁄8 EUE 63656

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.00 23⁄8 EUE 63657

51⁄2 20.0 - 23.0 4.670 4.778 4.500 2.38 27⁄8 EUE 63658

7 26.0 - 32.0 6.094 6.276 5.875 2.50 27⁄8 EUE 63670

7 17.0 - 26.0 6.276 6.538 6.000 2.50 27⁄8 EUE 63672

7 17.0 - 26.0 6.276 6.538 6.000 3.00 31⁄2 EUE 63674

75/8 24.0 - 29.7 6.875 7.025 6.672 2.50 27⁄8 EUE 63675

75/8 33.7 - 39.0 6.625 6.765 6.453 2.50 27⁄8 EUE 63676


Specification Guide



SL Shear Tension PackerThe Type SL Shear Tension Packer is an economical, compact tool for injection, pumping, medium range treating and production applications. This packer is set by 1/4 right-hand rotation of the tubing and then pulling tension. To release this tool the tubing is slacked off and the packer automatically rejays into the release position. This packer also has an adjustable straight pull, safety shear release and a right-hand rotation release allowing retrieval of the tubing string.

Special Features• Long element for increased packoff• Safety tubing release• Safety shear release• Deep wickered slips



Casing Packer Part Number

O.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection Box up/Pin down DL DL Shear

27⁄8 6.4 - 6.5 2.375 2.441 2.250 .75 1.315 NU 40125 4122531⁄2 7.7 - 10.2 2.922 3.068 2.781 1.50 1.900 EUE 40135 4123531⁄2 12.8 2.764 2.764 2.437 1.25 1.900 EUE 40136 412364 9.5 - 11.0 3.476 3.548 3.250 1.50 23⁄8 EUE 40140 412404 9.5 - 11.0 3.476 3.548 3.250 1.88 23⁄8 EUE 40141 41241

41⁄2 15.1 3.826 3.826 3.625 1.94 23⁄8 EUE 40143 4124341⁄2 15.1 - 16.6 3.754 3.826 3.500 1.94 23⁄8 EUE 40144 4124441⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 40145 412455 11.5 - 18.0 4.276 4.560 4.125 1.94 23⁄8 EUE 40150 41250

51⁄2 13.0 - 20.0 4.778 5.044 4.625 1.94 23⁄8 EUE 40155 4125551⁄2 13.0 - 20.0 4.778 5.044 4.625 2.44 27⁄8 EUE 10456 4125651⁄2 20.0 - 23.0 4.670 4.778 4.500 1.94 23⁄8 EUE 40157 4125751⁄2 20.0 - 23.0 4.670 4.778 4.500 2.44 27⁄8 EUE 40158 4125851⁄2 26.0 4.548 4.548 4.375 1.94 23⁄8 EUE 40159 412596 20.0 - 23.0 5.240 5.352 5.000 2.44 27⁄8 EUE 40160 412606 15.0 - 20.0 5.352 5.542 5.125 2.44 27⁄8 EUE 40161 41261

65/8 24.0 - 32.0 5.675 5.921 5.500 2.44 27⁄8 EUE 40165 4126565/8 20.0 - 24.0 5.921 6.049 5.750 2.44 27⁄8 EUE 40168 412687 17.0 - 29.0 6.184 6.538 6.000 2.44 27⁄8 EUE 40170 412707 17.0 - 29.0 6.184 6.538 6.000 3.00 31⁄2 EUE 40173 41273

75/8 20.0 - 33.7 6.765 7.125 6.625 2.44 27⁄8 EUE 40175 4127575/8 20.0 - 33.7 6.765 7.125 6.625 3.00 31⁄2 EUE 40177 4127785/8 24.4 - 40.0 7.725 8.097 7.500 2.44 27⁄8 EUE 40185 4128585/8 20.0 - 28.0 8.017 8.191 7.750 2.44 27⁄8 EUE 40186 4128685/8 24.4 - 40.0 7.725 8.097 7.500 3.00 31⁄2 EUE 40187 4128795/8 43.5 - 53.5 8.535 8.755 8.250 2.50 27⁄8 EUE 40194 4129495/8 29.3 - 43.5 8.755 9.063 8.500 2.50 27⁄8 EUE 400195 4129595/8 43.5 - 53.5 8.535 8.755 8.250 3.00 31⁄2 EUE 40196 4129695/8 29.3 - 43.5 8.755 9.063 8.500 3.00 31⁄2 EUE 40197 4129795/8 43.5 - 53.5 8.535 8.755 8.250 4.00 41⁄2 LTC 40198 4129895/8 32.3 - 43.5 8.755 9.001 8.500 4.00 41⁄2 LTC 40199 41299

103/4 32.7 - 55.5 9.760 10.192 9.500 3.00 31⁄2 EUE 40110 41210

133⁄8 48.0 - 72.0 12.347 12.715 12.000 4.00 41⁄2 EUE 40113 41213

* Other sizes and connections available on request.

Specification Guide



Type DL-1 Tandem Tension PackerThe DL-1 Tandem Tension Packer is an economical, compact, low-pressure, tension set, isolation packer used in casing or perforations and multi-zone injection installations. This packer runs with a tension set packer below. It can be run with the j-pins in the unjayed or jayed position. In the unjayed position applying tension shears the shear pins and allows pack-off. If run in the jayed position the DL-1 must be used with the ASI-X Packer. Set down weight shears the pins and left-hand rotation and applied tension will set the tool.

Special Features• Economical• Run in jayed or unjayed position• Optional J’s available

Casing PackerPart Number

O.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection Box up/Pin down

31⁄2 7.7 - 10.3 2.922 3.068 2.781 1.53 1.900 EUE 43735

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.94 23⁄8 EUE 43745

41⁄2 9.5 - 11.6 4.000 4.090 3.844 2.38 27⁄8 EUE 43746

5 15.0 - 18.0 4.276 4.408 4.125 2.00 23⁄8 EUE 43750

51⁄2 13.0 - 20.0 4.778 5.044 4.625 2.00 23⁄8 EUE 43756

7 17.0 - 29.0 6.184 6.538 6.000 2.50 27⁄8 EUE 43770

7 17.0 - 29.0 6.184 6.538 6.000 3.00 31⁄2 EUE 43773

75/8 29.7 - 33.7 6.765 6.875 6.500 2.50 27⁄8 EUE 43775

95/8 40.0 - 47.0 8.681 8.835 8.250 2.50 27⁄8 EUE 43795

95/8 40.0 - 43.5 8.755 8.835 8.500 3.00 31⁄2 EUE 43796


Specification Guide



Big Bore Casing PackerThe Big Bore Casing Packer is a large bore single grip tool used to isolate damaged casing and for production or injection. It can be run in tension or compression and can be used as a liner hanger when equipped with a right hand release sub. Coarse, deep wickered slips allow the packer to set in open hole or scaly casing. For open hole set, casing packers can be equipped with two elongated packing elements to assure a positive seal.

Special Features• Set/Run in tension or compression• Applicable for set in open hole• Can be used as a liner hanger• Full opening• Coarse, deep wickered slip teeth• Available with right or left hand set—manual or automatic release

Casing PackerPart

NumberO.D. Weight lb/ft

Tubing/Casing Min I.D. Max I.D. O.D. I.D. Thread Connections

Box up/Pin down

41⁄2 9.5 - 13.5 27⁄8 3.920 4.090 3.750 2.50 27⁄8 EUE 44045

5 11.5 - 20.3 27⁄8 4.184 4.560 4.000 2.50 27⁄8 EUE 44050

51⁄2 13.0 - 20.0 31⁄2 4.778 5.044 4.625 3.00 31⁄2 EUE 44055

51⁄2 13.0 - 17.0 4 4.892 5.044 4.650 3.50 4 NU 44056

53/4 14.0 - 17.0 4 5.190 5.290 4.875 3.50 41⁄2 EUE 44057

6 18.0 - 20.0 4 5.352 5.424 5.188 3.50 4 EUE 44060

65/8 20.0 - 28.0 41⁄2 5.791 6.049 5.625 4.00 41⁄2 LTC 44065

7 17.0 - 38.0 41⁄2 5.920 6.538 5.750 4.00 41⁄2 LTC 44070

7 20.0 - 29.0 5 6.184 6.456 5.969 4.50 5 LTC 44071

75/8 20.0 - 33.7 41⁄2 6.765 7.125 6.500 4.00 41⁄2 LTC 44075

75/8 20.0 - 33.7 51⁄2 6.765 7.125 6.500 5.00 51⁄2 LTC 44076

85/8 24.0 - 40.0 41⁄2 7.725 8.097 7.500 4.00 41⁄2 LTC 44084

85/8 24.0 - 40.0 51⁄2 7.725 8.097 7.500 5.00 51⁄2 LTC 44085

85/8 24.0 - 36.0 65/8 7.825 8.097 7.656 6.00 65/8 LTC 44086

85/8 24.0 - 36.0 7 7.825 8.097 7.656 6.50 7 LTC 44087

95/8 32.3 - 43.5 7 8.755 9.001 8.500 6.50 7 LTC 44095

103/4 32.7 - 55.5 7 9.760 10.192 9.500 6.50 7 LTC 44010

113/4 42.0 - 65.0 85/8 10.682 11.084 10.500 8.00 85/8 LTC 44011

133⁄8 48.0 - 77.0 95/8 12.275 12.715 12.000 8.75 95/8 LTC 44013

185/8 87.5 - 117.5 133⁄8 17.439 17.755 17.000 12.50 133⁄8 LTC 44018


Specification Guide



AD-1 Tension PackerThe AD-1 is a tension set, retrievable packer. Applications are for water flood, shallow or low fluid level wells with insufficient tubing weight to set compression packers.

Special Features• Compact• J-slot control for normal set and release• Shear ring secondary release• Right-hand safety joint emergency release• Rocker type slips• Inexpensive• Large bore available (45PADL-1 and/or 47PADL-1)• Parts interchangeable with other manufacturers



Casing PackerBase Product

NumberO.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Standard ThreadConnections

4 9.5 - 11.6 3.428 3.548 3.281 23⁄8 EU 8RD 41AD-A

41⁄2 9.5 - 13.5 3.920 4.090 3.771 23⁄8 EU 8RD 43AD-A

5 15.0 - 18.0 4.276 4.408 4.125 23⁄8 EU 8RD 43AD-B

5 11.5 - 15.0 4.408 4.560 4.250 23⁄8 EU 8RD 43AD-C

51⁄2 26.0 4.408 4.560 4.250 23⁄8 EU 8RD 43AD-C

51⁄2 20.0 - 23.0 4.670 4.778 4.500 23⁄8 EU 8RD 45AD-A2

51⁄2 15.5 - 20.0 4.778 4.950 4.641 23⁄8 EU 8RD 45AD-A4

51⁄2 13.0 - 15.5 4.950 5.044 4.781 23⁄8 EU 8RD 45AD-B

53/4 22.5 4.950 5.190 4.781 23⁄8 EU 8RD 45AD-B

6 26.0 4.950 5.190 4.781 23⁄8 EU 8RD 45AD-B

6 20.0 - 23.0 5.240 5.352 5.062 23⁄8 EU 8RD 45AD-C

65/8 24.0 5.830 5.921 5.656 27⁄8 EU 8RD 47AD-A2

65/8 17.0 - 20.0 6.049 5.190 5.812 27⁄8 EU 8RD 47AD-A4

7 38.0 5.830 5.921 5.656 27⁄8 EU 8RD 47AD-A2

7 32.0 - 35.0 6.044 6.094 5.812 27⁄8 EU 8RD 47AD-A4

7 26.0 - 29.0 6.184 6.276 5.968 27⁄8 EU 8RD 47AD-B2

7 20.0 - 26.0 6.276 6.456 6.078 27⁄8 EU 8RD 47AD-B4

7 17.0 - 20.0 6.456 6.538 6.266 27⁄8 EU 8RD 47AD-C2

75/8 33.7 - 39.0 6.625 6.765 6.453 27⁄8 EU 8RD 47AD-C4

75/8 24.0 - 29.7 6.875 7.025 6.672 27⁄8 EU 8RD 47AD-D2

75/8 20.0 - 24.0 7.025 7.125 6.812 27⁄8 EU 8RD 47AD-D4

85/8 40.0 - 49.0 7.511 7.725 7.312 31⁄2 EU 8RD 49AD-A2

85/8 32.0 - 40.0 7.725 7.921 7.531 31⁄2 EU 8RD 49AD-A4

85/8 20.0 - 28.0 8.017 8.191 7.781 31⁄2 EU 8RD 49AD-B

95/8 47.0 - 53.5 8.535 8.681 8.218 41⁄2 LTC 8RD 51AD-A2

95/8 40.0 - 47.0 8.681 8.835 8.437 41⁄2 LTC 8RD 51AD-A4

95/8 29.3 - 36.0 8.921 9.063 8.593 41⁄2 LTC 8RD 51AD-B

103/4 32.7 - 55.5 9.760 10.192 9.500 41⁄2 LTC X 41⁄2 STC 53AD-A

Specification Guide



GV-Cup PackerThe GV Cup Packer is an economical means for isolating casing leaks and depleted zones and is also a production or injection packer for low pressure applications. This packer can be run with cups opposing or in the same direction depending on the application. The GV Cup Available with packing element backup rings for higher pressure applications and comes in a full range of tubing and casing sizes in two or four cup models.

Casing Size Packer I.D. Thread Connection Part Number

31⁄2 1.50 1.900 NU 43935

41⁄2 2.00 23⁄8 EUE 43945

41⁄2 2.50 27⁄8 EUE 43946

51⁄2 3.00 31⁄2 EUE 43953

51⁄2 2.00 23⁄8 EUE 43955

51⁄2 2.50 27⁄8 EUE 43956

65/8 3.00 31⁄2 EUE 43965

65/8 4.00 41⁄2 LTC 43966

7 2.50 27⁄8 EUE 43970

7 4.00 41⁄2 LTC 43971

7 3.00 31⁄2 EUE 43973

7 4.00 41⁄2 LTC 43974

85/8 2.50 27⁄8 EUE 43985

95/8 3.00 31⁄2 EUE 43976

95/8 4.00 41⁄2 LTC 4391075


Specification Guide



Set Down Isolation PackerThe Set Down Isolation packer is an economical, compact compression set tool used to isolate casing or perforations. It can also be used in multi-zone injection applications. It runs above a compression set packer such as the AS-II or AS-III. Applied compression will shear the shear screws and allow pack-off. Straight pick-up releases the packer.

Casing PackerPart Number

O.D. Weight lb/ft Min I.D. Max I.D. O.D. I.D. Thread Connection Box up/Pin down

27⁄8 6.5 2.441 2.441 2.250 1.500 1.900 NU 64127

41⁄2 9.5 - 13.5 3.920 4.090 3.750 1.938 23⁄8 EUE 64145

5 11.5 - 18.0 4.276 4.560 4.000 1.938 23⁄8 EUE 64150

51⁄2 13.0 - 20.0 4.778 5.044 4.625 2.430 27⁄8 EUE 64156

51⁄2 13.0 - 20.0 4.778 5.044 4.625 1.938 23⁄8 EUE 64155

51⁄2 13.0 - 20.0 4.778 5.044 4.625 3.000 31⁄2 EUE 64158

7 17.0 - 26.0 6.276 6.538 6.000 2.430 27⁄8 EUE 64170

7 17.0 - 26.0 6.276 6.538 6.000 2.000 23⁄8 EUE 64171

7 32.0 - 35.0 6.004 6.094 5.750 4.000 41⁄2 8RD 64172

7 26.0 - 32.0 6.094 6.276 5.875 3.000 31⁄2 EUE 64173

7 17.0 - 26.0 6.276 6.538 6.000 3.000 31⁄2 EUE 64174

75/8 24.0 - 29.7 6.875 7.025 6.625 2.430 27⁄8 EUE 64175

95/8 40.0 - 47.0 8.681 8.835 8.438 4.000 41⁄2 EUE 64195

95/8 40.0 - 47.0 8.681 8.835 8.438 3.000 31⁄2 EUE 64196


Specification Guide



Permapak Seal Bore Production PackerThe versatile Permapak Seal Bore Production Packer can be used for single or multiple zone completions. It is for wells where high pressure/temperatures and corrosive fluids are present and it is available in a variety of elastomers and seal bore materials to meet a wide range of hostile downhole environments. This packer is recommended for injection stimulation and testing or can become a temporary bridge plug when used with our knockout or pump-out bottom assembly (see Permapak Tubing and Packer Accessories product sheet). The Permapak Packer comes with a complete line of tubing seal accessories and elastomers.

Special Features• Electric line, hydraulic or mechanical set• Components keyed for milling• Anti-extrusion rings expand to casing I.D. to prevent rubber extrusion• Full circle slips allow for fast run time

Casing Size Casing Weight (lbs./ft.)

Max O.D. of Tool Packer Bore Min. Bore

Thru Seals Part Number

31⁄2 7.7 - 10.2 2.750 1.750 1.187 67235

41⁄2 9.5 - 13.5 3.750 2.688 1.938 67245

41⁄2 15.1 3.600 2.500 1.910 67246

41⁄2 13.5 - 15.1 3.650 2.688 1.938 67247

5 15.0 - 20.0 3.968 2.688 1.938 67250

51⁄2 13.0 - 17.0 4.563 3.000 2.375 67255

51⁄2 13.0 - 17.0 4.563 2.688 1.938 67055

51⁄2 17.0 - 23.0 4.422 3.000 2.375 67256

51⁄2 17.0 - 23.0 4.437 2.688 1.938 67056

51⁄2 23.0 - 26.0 4.250 2.688 1.938 67057

65/8 17.0 - 32.0 5.468 3.250 2.375 67065

7 17.0 - 23.0 6.000 3.250 2.375 67070

7 23.0 - 32.0 5.813 3.250 2.375 67071

7 32.0 - 38.0 5.594 3.250 2.375 67072

7 17.0 - 23.0 5.969 4.000 3.000 67270

7 23.0 - 32.0 5.813 4.000 3.000 67271

7 32.0 - 38.0 5.594 4.000 3.000 67272

75/8 24.0 - 39.0 6.250 3.250 2.375 67075

75/8 24.0 - 39.0 6.250 4.000 3.000 67275

95/8 36.0 - 53.5 8.094 3.250 2.375 67093

95/8 36.0 - 53.5 8.125 4.750 3.500 67095

95/8 36.0 - 53.5 8.125 6.000 4.750 67295

103/4 40.5 - 51.0 9.469 4.000 3.000 67010

103/4 51.0 - 65.7 9.300 4.000 3.000 67010


Specification Guide



Gas Vent Pumping PackerThe Gas Vent Pumping Packer offers an inexpensive option for isolating casing leaks or depleted perforations in pumping wells. This tool prevents gas lock by allowing gas to vent to the surface past damaged zones. The interval between top and bottom cups can be any length. Available with single or multiple cups.

Special Features• Inexpensive alternative to squeeze job• Variable intervals easily adjusted• Optional single to multiple cups

Casing Size

Tubing Size

Liner Size

O.D. of Tool

I.D. of Tool

Part Number

41⁄2 23⁄8 3 3.813 2.69 42045

51⁄2 23⁄8 3 4.625 2.75 42055

51⁄2 27⁄8 31⁄2 4.625 3.19 42056

7 27⁄8 41⁄2 6.000 4.00 42070


Specification Guide



PBP Bridge PlugThe PBP Bridge Plug is a modular designed drillable bridge plug and is used for temporary and permanent zone isolation or well abandonment.

Special Features• Slimline design allows for quick wireline runs• Simple conversion to cement retainer• Specify mechanical or wireline set• Components rotationally locked for easy drillout

Casing Tool Max O.D.

Base Product NumberO.D. Weight lb/ft Min I.D. Max I.D.

41⁄2 9.5 - 15.1 3.826 4.090 3.593 43PBP

5 11.5 - 18.0 4.276 4.560 3.937 44PBP

51⁄2 13.0 - 23.0 4.670 5.044 4.312 45PBP

65/8 17.0 - 34.5 5.575 6.135 5.375 46PBP

7 32.0 - 44.0 5.720 6.094 5.375 47PBP

7 17.0 - 35.0 6.004 6.538 5.688 47PBP

75/8 20.0 - 39.0 6.625 7.125 6.312 48PBP

85/8 24.0 - 52.0 7.435 8.097 7.125 49PBP

95/8 29.3 - 61.1 8.375 9.063 8.125 51PBP

103/4 32.75 - 60.7 9.660 10.192 9.437 53PBP

113/4 38.0 - 60.0 10.772 11.150 10.437 54PBP

133⁄8 48.0 - 72.0 12.347 12.715 12.000 55PBP

16 65.0 - 128.0 14.438 15.250 14.125 57PBP

Specification Guide



Scab Liner Packer (SLP)The Scab Liner Packer (SLP) is an economical alternative to cement squeezing casing leaks or to isolate perforations. The system consists of an upper and lower packer with liner attached between them. Since the SLP uses packer-type sections it has proven to be much more durable than cup-type scab liners. The ID’s through the system are generally limited by the liner and frequently allow injection or production tubing to be run through the system and attached to existing tools below the SLP.

The packers and liner are carried in the hole with tubing or drill pipe, 1/4 turn rotationally set and mechanically packed off with pipe weight. After setting, pack off forces areretained by body lock rings in both packers. The SLP does not remain connected to the tubing string and is not affected by production or injection tubing movement. Tubing can be pulled and re-run without disturbing the SLP The SLP can be retrieved with the running tool if desired.

Casing Liner Size

Packer

Size Weight O.D. I.D.

41⁄2 9.5 - 12.6 27⁄8 3.75 2.5

5 15.0 - 18.0 27⁄8 4 2.5

51⁄2 14.0 - 20.0 4 4.641 3.35

7 20.0 - 29.0 41⁄2 5.95 4.5

75/8 20.0 - 33.7 51⁄2 6.5 5

85/8 24.0 - 40.0 51⁄2 7.5 5

95/8 32.3 - 43.5 7 8.5 6.5


Specification Guide

Upper Packer

Perforations or Casing Leak

Liner

Lower Packer



Pump-Out PlugPump-Out Plugs are available with a choice of threads allowing installation to the bottom of the tubing string to isolate the tubing from the annulus. To remove the plug pressure is applied to the tubing and the Pump-Out Plug is removed to allow full opening. The pump out pressure value is easily adjusted in the field.

Plug O.D. Thread Connection Part Number

2.200 1.600 EUE 59716E

2.062 1.600 NU 59716N

2.500 1.900 EUE 59719E

2.200 1.900 NU 59719N

3.063 23⁄8 EUE 59720

3.670 27⁄8 EUE 59727

4.500 31⁄2 EUE 59735


Specification Guide



Hydroset IIThe Hydroset II is a hydraulic set, mechanically held dual string production packer run above a single string hydraulic set or wireline set seal bore packer. Its short length makes it ideal for deviated wells or doglegs. Because no tubing manipulation is required to set this packer, the well head can be installed and flanged up before setting. It is available with short or long string setting capabilities and a variety of tubing connections. It is also adaptable for submersible pump applications. The Hydroset II features a sequential upper slip release system designed to release each slip individually reducing the pull required to release the packer. Due to the angles on the upper slips and upper slip cage, slips release smoothly from the casing.

Casing Max O.D.

of Tool

Long String Short StringPart

NumberO.D. Weight lb/ft

Min I.D.

Max I.D.

Connection Box up/Pin down

MandrelI.D.

Connection Box up/Pin down

Seal Bore I.D.

51⁄2 14.0 - 20.0 4.778 5.012 4.625 1.900 NU 10 RD 1.500 1.660 NU 10 RD 1.375 90555

7 26.0 - 32.0 6.094 6.276 5.935 23⁄8 EUE 8 RD 1.938 23⁄8 NU 10 RD 1.938 90570

7 17.0 - 26.0 6.276 6.538 6.000 23⁄8 NU 10 RD 1.938 23⁄8 NU 10 RD 1.938 90572


Specification Guide



Permapak Tubing & Packer Accessories

Concentric BottomUsed to connect a seal boreextension to a packer.

Mill-Out BottomUsed to connect Mill-Out

Extension to packer.

Seal Bore ExtensionUsed in installations wherefloating seals are required due to tubing contractions. This packer accessory allows for a continuous seal bore and is available in five to ten foot lengths.

Mill-Out ExtensionUsed in installations where floating seals

are required due to tubing contractions. In addition this packer accessory provides a larger

inside diameter between a packer bore and a seal bore extension to allow for a packer

plucker in cases where the packer is milled out.

Concentric CouplingUsed to connect seal boreextensions to increase length.

Seal Bore to Mill-Out Coupling

Used to connect mill-out extensions to seal bore extensions.

Pump-Out PlugAvailable with a choice of threads to allow the pump-out plug to be attached to a packer, seal bore extension, mill-out extension or tailpipe and hold pressure from below once the packer is set. Once the production string is landed, pressure is applied to the tubing and the pump-out plug is removed to allow full opening.

Wireline Re-Entry BottomUsed as the packer bottom when extension below a packer is not required.

Knock-Out Plug BottomWhen run below the packer, the

knock-out plug allows a packer toserve as a bridge plug holding

pressure from above and below.

Knock-Out PlugThe plug is knocked-out when

the production string is landed.



Locator Seal AssemblyThe locator seal assembly is used in installations where floating seals arerequired. Once landed the seal locator prevents downward movement of

the tubing while allowing the seal to move with tubing contraction.

Anchor Latch AssemblyThe anchor latch seal assembly is used where floating seals are notrequired. This assembly allows the tubing string to be in tension orcompression. Upon set down the anchor latches into the packer and canbe removed with eight to ten right-hand turns.

Snap Latch AssemblyLike our anchor latch seal assembly, the snap latch seal assembly latches

into the packer upon set down. It can be removed with straight pull of10,000 to 12,000 pounds above tubing weight. The snap latch seal

assembly is used where a mechanical indication is required to verify theseal assembly is properly positioned in the packer bore.

Seal UnitStandard seal units are furnished with bonded nitrile rings and a 12-inchmake-up length. These units may be ordered in various lengths and withsevere service seal rings for high temperature and corrosiveenvironmental conditions.

Half Mule Shoe GuideThe half mule shoe guide is standard with the seal

assembly to allow for easy entry into the packer bore.



BA Tubing Anchor CatcherThe BA acts as a tubing anchor to maintain tension in the tubing string and as a tubing catcher to prevent parted pipe from falling to the bottom of the well. The BA is used in most rod pumping applications where it is important to maintain tension in the tubing.

Special Features• Rotate left to set, right to release• Straight pull emergency shear release• Increases pump efficiency• Improves operating costs by reducing maintenance and down time caused by tubing or sucker rod wear• Parts interchangeable with other manufacturers

Setting ProcedureAt the desired setting depth, rotate the tubing to the left with hand wrenches until the slips contact the casing (approximately five to eight turns). Maintain left hand torque while alternately pulling strain and setting down several times to work all the slack out of the tool.

Releasing ProcedureWith tubing in slight compression, rotate the tubing to the right (five to eight turns at the tool) to retract the cones from the slips and allow the slips to move back into the housing. To insure a complete release, reciprocate the tubing string a few feet while rotating a few more turns to the right before starting out of the hole. If normal release is not possible, an upstrain greater than the total shear strength of the shear pins plus the weight of the tubing.

Casing AnchorBase Product

NumberO.D. Weight lb/ft Min I.D. Max I.D. Max O.D. Standard Thread Connections

41⁄2 9.5 - 13.5 3.920 4.090 3.750 23⁄8 EU 8RD 43BA-A

5 11.5 - 18.0 4.276 4.560 4.000 23⁄8 EU 8RD 43BA-B

51⁄2 13.0 - 23.0 4.670 5.044 4.500 23⁄8 EU 8RD or 27⁄8 EU 8RD 45BA-A

6 18.0 - 23.0 5.240 5.424 4.812 23⁄8 EU 8RD or 27⁄8 EU 8RD 45BA-B

65/8 17.0 - 32.0 5.675 6.135 5.500 23⁄8 EU 8RD or 27⁄8 EU 8RD 47BA-A

7 20.0 - 38.0 5.920 6.456 5.500 23⁄8 EU 8RD or 27⁄8 EU 8RD 47BA-A

7 17.0 - 20.0 6.456 6.538 6.250 23⁄8 EU 8RD or 27⁄8 EU 8RD 47BA-B

75/8 20.0 - 39.0 6.625 7.125 6.250 23⁄8 EU 8RD or 27⁄8 EU 8RD 47BA-B

65/8 17.0 - 32.0 5.675 6.135 5.500 31⁄2 EU 8RD 47BA X 3.00

7 17.0 - 38.0 5.920 6.538 5.500 31⁄2 EU 8RD 47BA X 3.00

85/8 24.0 - 49.0 7.511 8.097 7.000 31⁄2 EU 8RD 49BA

95/8 32.3 - 47.0 8.681 9.001 8.000 31⁄2 EU 8RD 51BA

Specification Guide



Shear & Rotational Safety JointThe Safety Joints allow positive release of the tubing string in completions where retrieval problems are anticipated. These safety joints are available in straight pull or rotational release versions.

Casing O.D.

Packer O.D.

Tool I.D.

Thread Connection Box up/Pin down

Part Number

1.315 1.750 0.75 1.315 NU 56910N

1.660 2.250 1.25 1.660 EUE 56916E

1.660 2.063 1.25 1.660 NU 56926N

1.900 2.688 1.61 1.900 NU 56919N

23⁄8 3.063 2.00 23⁄8 EUE 56920E

27⁄8 3.688 2.50 27⁄8 EUE 56927E

31⁄2 4.500 3.00 31⁄2 EUE 56935E


Shear Out Specification Guide

Casing O.D.

Packer O.D.

Tool I.D.

Thread Connection Box up/Pin down

Part Number

1.660 2.250 1.25 1.660 NU 56816N

23⁄8 3.063 2.00 23⁄8 EUE 56820E

27⁄8 3.688 2.50 27⁄8 EUE 56825E

31⁄2 4.500 3.00 31⁄2 EUE 56835E


Rotational Specification Guide



Pump-Out Cementing SleeveThe Pump-Out Cementing Sleeve is used for cementing tubing strings in both cased and open holes. It allows for internal parts to be pumped out after the cementing process leaving a full open bore with no loss of tubing strength. Available in any material necessary to meet customer needs. A basket or packer placed below the sleeve provides a seal-point for pumping cement up the outside of the tubing string.

OperationsSimplicity is the key to the Pump-Out Plug Cementing Sleeve. Pressure applied to the trip ball moves the lower piston past the cementing ports allowing cement to be pumped outside the tubing string. After the desired amount of cement has been placed the wiper plug is pumped down to the sleeve and moves the upper piston and outer sleeve over the cementing ports. Pins are then sheared and the upper and lower pistons are pumped out of the bottom of the tool leaving a full and unrestricted opening through the sleeve. The outer sleeve is locked in the closed position.

Size Min I.D. Max O.D. Thread Connection

I.D. After Pump-out Part Number

23⁄8 1.00 3.250 23⁄8 EUE 1.92 22020

27⁄8 1.25 3.750 27⁄8 EUE 2.40 22027

31⁄2 1.25 4.410 31⁄2 EUE 2.90 22035

4 1.25 4.625 4 NU 3.45 22040

41⁄2 1.25 5.500 41⁄2 8RD 3.97 22045

51⁄2 1.25 6.130 51⁄2 8RD 4.62 22055


Specification Guide



Bit ReleaseThe Bit Release is used in operations for drilling out cement, cast iron bridge plugs and other drillable tools and thereby leaving the drill string intact as the production string. The spring loaded check valve prevents tubing back flow during drillout. After drillout a ball is dropped through the drill string and seats in the piston. Pressure applied to the drill string forces the drill bit to release and fall to the bottom of the hole

Top Connection Bottom Connection Tool O.D. Part Number

23⁄8 8RD EUE 23⁄8 REG. DRILL PIPE 3.67 80020020






Specification Guide



Cement Port Collar &Shifting ToolThe Cement Port Collar provides a full opening stage cementer that needs no plugs or balls to operate. An internal cementing sleeve is opened and closed with pipe manipulation using a shifting tool. Since no plugs are needed, multiple port collars can be run in a casing string. All can be operated with a single workstring trip. The port collar has a full opening to allow other tools to pass without restriction.

The Port Collar Shifting Tool uses spring loaded blocks that locate in the cementing sleeve providing a tie to the workstring. Once the blocks locate in the sleeve, right-hand pipe rotation and manipulation are used to open and close the sleeve. Multiple openings and closings are possible with each port collar.

Special Features• Sleeves lock in the open and closed position• No plug or ball drillout• Multiple port collars in the same casing string• Easy location of shifting tool in the port collar

Casing O.D. Tool O.D. Tool I.D. Thread Connection Box up/Pin down Part Number

41⁄2 3.750 1.250 23⁄8 EUE 21745

51⁄2 4.500 1.250 27⁄8 EUE 21755


Port Collar Shifting Tool Specification Guide

Casing O.D. Tool O.D. Tool I.D. Thread Connection Box up/Pin down Part Number

41⁄2 5.750 4.000 41⁄2 8RD 23045

51⁄2 6.750 5.000 51⁄2 8RD 23055


Cement Port Collar Specification Guide



Type A Cementing ShoePacker TypeType A Cementing Shoe is designed to effectively protect the formation below the shoe from cement contamination. The rubber packing element, when expanded, not only retains the cement above the shoe, but also assures a seal between the casing and the formation. This is particularly important in the completion of water input wells.

The Type A Cementing Shoe is made up on the casing string and run to the point where the casing is to be cemented. The tripping ball is dropped and allowed to gravitate to its seat.

Pump pressure is then slowly built up in the casing. The pressure will move the inner piston downward, allowing fluid to enter the outside cylinder. Continued pressure will force fluid behind the packing rubber while moving the top of the rubber downward. This will expand the packing rubber to seal against the sides of the open hole. Pressure of approximately 500 P.S.I. will shear the bolts holding the sliding sleeve. The sleeve will move downward, opening the cementing ports and locking the packing rubber in its expanded position. The tripping ball prevents cement slurry from entering the bottom of the shoe, and the cement leaves the casing through the cementing ports above the packing element.

All internal parts of the shoe are easily drillable.



Multi-Stage Cementing CollarThe Multi-Stage Cementing Collar provides an effective, economical way to cement one or more specific casing intervals or to cement upper zones after a lower zone has been cemented. The collar should be used with centralizers above and below and a Cementing Basket positioned below the ports. The operation of the collar is simple and reliable. It features a double locking mechanism consisting of a snap ring lock and ball lock system to assure that the ports are permanently locked closed after cementing is completed. Internal parts are designed to lock to prevent rotation during drill out and are constructed of easily drillable materials.

Special Features• Economical• Helps prevent possible formation damage• Easy drill out• Will not spin during drill out• Available in two or three stage• Available with by-pass plug system

Tubing or Casing Size I.D.

Lower Seat I.D.

Upper Seat I.D.

Max O.D.

Opening Press PSI

Part Number

31⁄2 EU 8RD 3.125 2.125 2.500 4.625 1220 210-35

41⁄2 EU 8RD 4.000 2.750 3.250 5.750 1010 210-45

5 EU 8RD 4.500 3.250 3.500 6.090 1580 210-50

51⁄2 EU 8RD 5.000 3.313 4.000 6.750 1000 210-55

7 EU 8RD 6.500 4.375 5.125 8.250 890 210-70

7 EU 8RD 6.250 4.375 5.125 8.062 1000 210-71

75/8 EU 8RD 7.000 4.875 5.750 9.000 960 210-75

85/8 EU 8RD 8.000 5.750 6.500 10.000 940 210-85

95/8 EU 8RD 9.000 7.000 7.750 11.000 760 210-95

103/4 EU 8RD 10.000 8.000 8.750 12.500 610 210-10

133⁄8 EU 8RD 12.500 10.500 11.250 15.500 460 210-13

16 EU 8RD 15.250 13.000 14.000 18.250 420 210-16

Tools available for use with API, Extreme Line, Buttress, Vam, Hydrill, Etc.

Specification Guide



Multi-Stage Cementing CollarOperation ProceduresThe Multi-Stage Cementing Collar is run in the casing string at the point where stage cementing is desired. The first stage shut-off baffle is installed in a collar above the float system used for the first stage. The first stage is cemented conventionally and displayed with a flexible wiper plug.

The trip bomb is dropped and allowed to fall to the lower seat of the cementing collar. Pressure is applied to the casing to open the cementing ports in the collar. The second stage of cementing is performed and the closing plug is used to displace the second stage cement. When the closing plug lands on the upper seat it closes the ports at 1000 PSI pump pressure and the cementing collar locks closed preventing cement slurry flow back.

Centralizers should run above and below the cementing collar and cementing basket run just below the ports of the cementing collar, if necessary.

NOTE: Two (2) plugs, first stage shut-off baffle, and bomb are furnished with the collar.



Gard Mill-EZ™

Composite Bridge PlugThe Gard Mill-EZ™ is a slim design Composite Bridge Plug (CBP). This tool is set like a conventional bridge plug. Because of its low metallic content the Gard Mill-EZ™ can be quickly and easily milled and circulated back to surface. The patented bottom allows for easy milling of several plugs in the same well bore. This may be accomplished with conventional milling or drilling with a rig and tubing or with coiled tubing.

Special Features• Can be set on wireline, coiled tubing, or production tubing• Utilizes conventional setting tools• Multiple plugs in a single well bore• Mill or drill multiple plugs in a single run• Can be milled or drilled with coil tubing• Utilize conventional milling or drilling tools• Extremely fast milling or drilling operation• High differential pressure rating• Patented wash-thru bottom to aid in milling multiple plugs

Casing Bridge Plug O.D.

Bridge Plug Set Length Temp °F

Differential Pressure Rating (PSI) Recommended

Setting ToolO.D. Weight Above Below

27⁄8 6.5 - 7.9 2.15 11.0 350° 10,000 10,000 111⁄16 GO SettingTool Slow-Set

31⁄2 12.95 2.60 11.0 350° 10,000 10,000 111⁄16 GO SettingTool Slow-Set

31⁄2 9.30 2.80 11.0 350° 10,000 10,000 111⁄16 GO SettingTool Slow-Set

41⁄2 10.5 - 15.1 3.60 16.0 350° 10,000 10,000 #10 Baker E-4 Slow-Burn

5 11.5 - 21.0 4.10 16.0 350° 10,000 10,000 #10 Baker E-4 Slow-Burn

51⁄2 17.0 - 23.0 4.40 16.0 350° 10,000 10,000 #20 Baker E-4 Slow-Burn

7 26.0 - 38.0 5.75 18.0 350° 8,000 8,000 #20 Baker E-4 Slow-Burn

Specification Guide



Gard Mill-EZ™

Flo-Back Composite Bridge PlugThe Gard Mill-EZ™ Flo-Back is a slim design Composite Bridge Plug (CBP), with a built in one way check valve. This tool is set like a conventional bridgeplug. When the pressure below the plug is greater than the pressure above, the check valve will allow the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug in anunder balanced environment in one trip. Because of it’s low metallic content the Gard Mill-EZ™ Flo-Back can be quickly and easily milled and circulated back to surface. This may be accomplished with conventional milling or drilling with a rig and tubing or with coiled tubing.

Special Features• Can be set on wireline, coiled tubing, or production tubing• Utilizes conventional setting tools• Multiple plugs in a single well bore• Mill or drill multiple plugs in a single run• Can be milled or drilled with coil tubing• Utilize conventional milling or drilling tools• Extremely fast milling or drilling operation• High differential pressure rating• Positive ball seat check valve system

Casing Bridge Plug O.D.

Bridge Plug Set Length Temp °F

Differential Pressure Rating (PSI) Recommended

Setting ToolO.D. Weight Above Below

41⁄2 10.5 - 15.1 3.60 16.0 350° 10,000 10,000 #10 Baker E-4 Slow-Burn

5 11.5 - 21.0 4.10 16.0 350° 10,000 10,000 #10 Baker E-4 Slow-Burn

51⁄2 17.0 - 23.0 4.40 16.0 350° 10,000 10,000 #20 Baker E-4 Slow-Burn

7 26.0 - 38.0 5.75 18.0 350° 8,000 8,000 #20 Baker E-4 Slow-Burn


Specification Guide

Midland, TexasCorporate Office

600 N. Big SpringMidland, TX 79701

432-620-0062

San Angelo, Texas4825 Old Christoval Rd. San Angelo, TX 76904

325-617-5841

Odessa, Texas 2201 W. 39th

Odessa, TX 79763432.552.9325

Monahans, Texas2909 S. Stockton HwyMonahans, TX 79756

432.943.7006

Andrews, Texas410 NW Mustang Dr.Andrews, TX 79714

432.524.4385

Hobbs, New Mexico320 NW County Road

PO Box 748Hobbs, NM 88241-0748

575.631.5323

copyright ©2014, Watson Packer rev. 04/2014

432-552-0102www.watsonpacker.com

History and Resources - Watson Packer

Documents

Transcript of History and Resources - Watson Packer