GCX Mounting Assembly Installation Guide Rev A 6/26/02 GCX Corp. Page 1 of 5 GCX Mounting Assembly...
5
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 1 of 5 GCX Mounting Assembly Installation Guide Accessory Handle The purpose of these instructions is to: 1. Describe attachment of Handle to VHM Arm. 2. Describe attachment of Handle to Down Post. 3. Describe attachment of Handle to Down Post and Yoke. 4. Describe attachment of Handle to Variable Height Roll Stand. 5. Describe attachment of Handle to Laptop Tray. REFER TO QUALIFIED PERSONNEL Attachment of Handle to VHM Arm 1. To prepare the VHM Arm for attachment of Handle, insert the supplied #8-32 x ¼" SHCS (1) into the Lower Swivel Washer. 2. Take the Lower Swivel Fitting and place it over the washer, aligning the three (3) hole pattern. Secure using the supplied #10-32 x ¾” SHCS (3). Lower Swivel Washer #8-32 x ¼” SHCS (1) #10-32 x ¾" SHCS (3) Lower Swivel Fitting
Transcript of GCX Mounting Assembly Installation Guide Rev A 6/26/02 GCX Corp. Page 1 of 5 GCX Mounting Assembly...
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 1 of 5
GCX Mounting Assembly Installation Guide
Accessory Handle The purpose of these instructions is to: 1. Describe attachment of Handle to VHM Arm. 2. Describe attachment of Handle to Down Post. 3. Describe attachment of Handle to Down Post and Yoke. 4. Describe attachment of Handle to Variable Height Roll Stand. 5. Describe attachment of Handle to Laptop Tray.
REFER TO QUALIFIED PERSONNEL Attachment of Handle to VHM Arm 1. To prepare the VHM Arm for attachment of Handle, insert the supplied #8-32 x ¼" SHCS (1) into the Lower Swivel Washer. 2. Take the Lower Swivel Fitting and place it over the washer, aligning the three (3) hole pattern. Secure using the supplied #10-32 x ¾” SHCS (3).
Lower Swivel Washer
#8-32 x ¼” SHCS (1)
#10-32 x ¾" SHCS (3)
Lower Swivel Fitting
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 2 of 5
3. Align the three (3) hole pattern on the Handle, with the three (3) hole pattern on the Lower Swivel Fitting. Use the supplied #10-32 x 3/8" PHMS (3) to secure the Handle to the Lower Swivel Fitting. Attachment of Handle to Down Post 1. Align the three (3) hole pattern in the Handle with the three (3) hole pattern on the top of the Down Post.
#10-32 x 3/8” PHMS (3)
Lower Swivel Fitting
Three Hole Pattern
Handle
Three Hole Pattern
Down Post
Three Hole Pattern
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 3 of 5
2. Use the supplied #10-32 x 3/8" PHMS (3) to secure the Handle to the Down Post. Attachment of Handle to Down Post and Yoke 1. Align the three (3) hole pattern on the Down Post, Handle, and Yoke as shown below. Use the supplied #10-32 x ¾" PHMS (3) to secure all three devices together.
#10-32 x ¾" PHMS (3)
Yoke
Handle Down Post
Down Post
Handle
#10-32 x 3/8" PHMS (3)
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 4 of 5
Attachment of Handle to Variable Height Roll Stand 1. Attach the Handle to the Ergo Bracket by aligning the four (4) hole patterns and secure with the supplied #10-32 x 7/16" FHMS (1).
2. Attach the Ergo bracket and Handle assembly to the Roll Stand by aligning the remaining three (3) hole pattern and secure using the supplied #10-32 x 5/8" FHMS (3). 3. Complete the installation in accordance with the separately printed instructions, DU-WM-0023.
#10-32 x 7/16" FHMS (1)
Handle
Ergo Bracket
#10-32 x 5/8" FHMS (3)
DU-WS-0003-10 Rev A 6/26/02 GCX Corp. Page 5 of 5
Attachment of Handle to Laptop Tray 1. Line up the three (3) hole pattern on the bottom of the Laptop Tray Bracket with the three (3) hole pattern on the Handle and secure using the supplied #10-32 x 3/8" PHMS (3).
Laptop Tray Laptop Tray Bracket
#10-32 x 3/8" (3)
Handle
