Floors Cleaning Manual

8/20/2019 Floors Cleaning Manual

http://slidepdf.com/reader/full/floors-cleaning-manual 1/7

Public Areas Cleaning Manual


Prepared For

Prepared By





1- Remove the dust

2- Brush with R2 solution for sticky dirt ‘manual or

by machine”

3- Clean the water out

1- Remove the dust

2- Brush with R2 solution for sticky dirt ‘manual or

by machine”

3- Clean the water out

Hard Surfaces –

Ceramic Tiles

Safety & Hygiene





1- Remove the dust

2- Apply Tontec Tensol or Taski 300 or Jontec Secure

solution

3- let the solution to be semi dried for 5 to 10 min

4- buffing with the white pad

1- Remove the dust

2- Apply Tontec Tensol or Taski 300 or Jontec Secure

solution

3- let the solution to be semi dried for 5 to 10 min

4- buffing with the white pad

Hard Surfaces –

Marble and Garnet daily Maintenance

Safety & Hygiene



Public Areas Cleaning ManualPublic Areas Cleaning Manual

1- Remove the dust or sticky dirt with R2 solution for HK

Or Suma Light D12 for Stewarding

2- Dry the surface with dump cloth

3- Use clean dump cloth to spray Suma Inox solution

3- buff the surface in cycle action to polish it

1- Remove the dust or sticky dirt with R2 solution for HK

Or Suma Light D12 for Stewarding

2- Dry the surface with dump cloth

3- Use clean dump cloth to spray Suma Inox solution

3- buff the surface in cycle action to polish it

Stainless steel Surface

Not used for food contact or heated stainless steel surfacesNot used for food contact or heated stainless steel surfacesSafety & Hygiene




1- remove any removable furni ture, sticky gum,

and stains

2- Test colour-fastness and material compatibi lity

Test colour-fastness and material compatibi lity

3- Start at the furthest point from the door, switch on the foam

generator. Wait unti l the foam comes out of the brush.

4- Move to the carpet to be cleaned, work backwards in lanes moving

the machine in circular motions sideways. Do not over wet thecarpet.

5- Fill clean water into the fresh water tank of the spray extraction

machine. Clean immediately the carpet working in overlapping

lanes. Use an antifoam product i f foam develops

6- Lift the carpet piles with a carpet pile brush or rake. Allow the

carpet to dry thoroughly. Drying time between 8 to 24 hours before

walking on the carpet7- Empty the water tank of the single disc machine, empty the fresh

water and recovery tank of the spray extraction machine. Rinse the

brush and tanks wi th clean water. Clean the machines and the

cable with a moist cloth. Wind the cable loosely

1- remove any removable furni ture, sticky gum,

and stains2- Test colour-fastness and material compatibi lity

Test colour-fastness and material compatibil ity


generator. Wait unti l the foam comes out of the brush.

4- Move to the carpet to be cleaned, work backwards in lanes moving

the machine in circular motions sideways. Do not over wet the

carpet.

5- Fill clean water into the fresh water tank of the spray extraction

machine. Clean immediately the carpet working in overlapping

lanes. Use an antifoam product i f foam develops

6- Lift the carpet piles with a carpet pile brush or rake. Allow the

carpet to dry thoroughly. Drying time between 8 to 24 hours before

walking on the carpet7- Empty the water tank of the single disc machine, empty the fresh

water and recovery tank of the spray extraction machine. Rinse the

brush and tanks with clean water. Clean the machines and the

cable with a moist cloth. Wind the cable loosely

Carpet Floors –

Wet Shampooing

Safety & Hygiene




1- remove any removable furniture, sticky gum,

and stains

2- Test colour-fastness and material compatibil ity


generator. Wait until the foam comes out of the brush.

4- Apply dry foam by working backwards in lanes,moving the machine in circular motions sideways. After applying 3

lanes, work over it again in circular motions

5- Lif t the carpet piles with a carpet pile brush

6- Rinse the brush, edge cleaning tool and the sinter head from the

foam generator with clean water. Clean machines and cable with a

moist cloth. Wind the cable loosely.

7- Brush vacuum the carpet thoroughly as soon carpet is dry to

remove the dirt/crystallized foam.

1- remove any removable furniture, sticky gum,

and stains

2- Test colour-fastness and material compatibi lity


generator. Wait until the foam comes out of the brush.

4- Apply dry foam by working backwards in lanes,moving the machine in circular motions sideways. After applying 3

lanes, work over it again in circular motions

5- Lif t the carpet piles with a carpet pile brush

6- Rinse the brush, edge cleaning tool and the sinter head from the

foam generator with clean water. Clean machines and cable with a

moist cloth. Wind the cable loosely.7- Brush vacuum the carpet thoroughly as soon carpet is dry to

remove the dirt/crystallized foam.

Carpet Floors –

Dry Shampooing

Safety & Hygiene




1- remove all dust or any dirt

2- spray Traffic Liquid wax solution

3- Apply the single desk with red pad for 5 min each

1 Sq. meter

4 – Apply the white pad for puffing for 5 min. each

1 Sq. meter

1- remove all dust or any dirt

2- spray Traffic Liquid wax solution

3- Apply the single desk with red pad for 5 min each1 Sq. meter

4 – Apply the white pad for puffing for 5 min. each

1 Sq. meter

Wooden Floor

Safety & Hygiene

Floors Cleaning Manual

Documents

Transcript of Floors Cleaning Manual