DSAM_Field_View__QAM_Quick_Guide_EN.PDF
-
Upload
dana-kincaid -
Category
Documents
-
view
95 -
download
0
Transcript of DSAM_Field_View__QAM_Quick_Guide_EN.PDF
DSAM Field View QAM™ Guide
DSAM Field View QAM™ Guide
Reference WEBSITE: www.jdsu.com/test
Notice Every effort was made to ensure that the information in this document was accurate at the time of printing. However, information is subject to change without notice, and JDSU reserves the right to update this document with information not available at the time that this document was created.
Copyright © Copyright 2012 JDS Uniphase Corporation (JDSU). All rights Reserved.
JDSU, Enabling Broadband and Optical Innovation, Test and Measurement Solutions, and JDSU logos are trademarks of JDS Uniphase Corporation ("JDS Uniphase"). All other trademarks and registered trademarks are the property of their respective owners. No part of this guide may be reproduced or transmitted electronically or otherwise without written permission of the publisher.
Trademarks JDSU and Field View QAM™ are trademarks or registered trademarks of JDSU in the United States and/or other countries.
Microsoft, Windows, Windows CE, Windows NT, and Microsoft Internet Explorer are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Specifications, terms, and conditions are subject to change without notice. All trademarks and registered trademarks are the property of their respective companies.
WEEE DirectiveCompliance
JDSU has established processes in compliance with the Waste Elec-trical and Electronic Equipment (WEEE) Directive, 2002/96/EC.
This product should not be disposed of as unsorted municipal waste and should be collected separately and disposed of according to your national regulations. In the European Union, all equipment purchased from JDSU after 2005-08-13 can be returned for disposal at the end of its useful life. JDSU will ensure that all waste equipment returned is reused, recycled, or disposed of in an environmentally friendly manner, and in compliance with all applicable national and interna-tional waste legislation.
Rev. 001 DSAM Field View QAM Guide i
It is the responsibility of the equipment owner to return the equipment to JDSU for appropriate disposal. If the equipment was imported by a reseller whose name or logo is marked on the equipment, then the owner should return the equipment directly to the reseller.
Instructions for returning waste equipment to JDSU can be found in the Environmental section of JDSU’s web site at www.jdsu.com. If you have questions concerning disposal of your equipment, contact JDSU’s WEEE Program Management team at [email protected].
ii DSAM Field View QAM Guide Rev. 001
Table of Contents
Field View QAM™ Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Field View QAM™ - Troubleshooting with Field View QAM™ . . 2DSAM Field View QAM™- Example of Detected Problems . . . . . 8
Rev. 001 DSAM Field View QAM Guide iii
Table of Contents
iv DSAM Field View QAM Guide Rev. 000
DSAM Field View QAM GuideField View QAM™ Overview
Field View QAM™ OverviewLocate and Repair hard-to-find impairments on the Return Path. Tradi-tional spectrum analysis tools can show a clean spectrum, indicating pristine return path, while the CMTS and other reporting tools give overall node health a low health score. With Field View QAM™ micro-reflections, in-band frequency response and group delay issues that are undetectable when viewing only the spectrum can be quickly iden-tified.
A DSAMXT with Field View QAM™ can display an impairment dash-board with key measurements displayed in green and red providing a quick go/no-go indicator to technicians, confirming whether issues causing codeword errors such as microreflections and impulse noise have been fixed. 3
9
Figure 1 Impairments Invisible with Spectrum Analysis
Figure 2 Same Impairments Visible with Field View QAM
Rev. 001 DSAM Field View QAM Guide 1
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
Field View QAM™ - Troubleshooting with Field View QAM™
1 Press the Measure hard key on the DSAM keypad.
2 Press the Service softkey
3 Got to Field View QAM™
4 Enter
5 If you have multiple DOCSIS Channels available to test you will be asked to select a DOCSIS Channel
6 Select a DOCSIS channel that you want to troubleshoot
7 Press Next>
Figure 3
Figure 4
2 DSAM Field View QAM Guide Rev. 001
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
8 Press Start>
9 Select a PathTrak WebView Server
10 Ok
11 Select an HCU
12 Ok
13 Select a Node
14 Ok
15 Select an upstream
16 Ok
Figure 5
Figure 6
Rev. 001 DSAM Field View QAM Guide 3
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
Figure 7
Figure 8 Initial FVQ Screen
4 DSAM Field View QAM Guide Rev. 001
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
17 Select Carrier Level
18 Enter
19 Press the Back softkey
20 Using the down arrow key, select In-Band Response
21 Go Back
Figure 9 Carrier Level
Figure 10 In-Band Response
Rev. 001 DSAM Field View QAM Guide 5
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
22 Select Ingress Under Carrier
23 Back
24 Using the arrow keys, select Micro-reflection
25 Back
Figure 11 Ingress Under Carrier
Figure 12 Micro-reflection
6 DSAM Field View QAM Guide Rev. 001
DSAM Field View QAM GuideField View QAM™ - Troubleshooting with Field View QAM™
26 Select Group Delay
27 Back
28 Select Impulse Noise
Figure 13 Group Delay
Figure 14 Impulse Noise
Rev. 001 DSAM Field View QAM Guide 7
DSAM Field View QAM GuideDSAM Field View QAM™- Example of Detected Problems
DSAM Field View QAM™- Example of Detected Problems
Figure 15 Bad Packets
Figure 16 Bad Packets (In-Band Response)
Figure 17 Bad In-Band Response
8 DSAM Field View QAM Guide Rev. 001
DSAM Field View QAM GuideDSAM Field View QAM™- Example of Detected Problems
Figure 18 Bad Group Delay
Rev. 001 DSAM Field View QAM Guide 9
DSAM Field View QAM GuideDSAM Field View QAM™- Example of Detected Problems
10 DSAM Field View QAM Guide Rev. 001
Test and Measurement Regional Sales
North AmericaToll Free: 1 800 638 2049Tel: +1 240 404 2999Fax:+1 240 404 2195
Latin AmericaTel: 954-688-5660Fax:954-846-8856
Asia PacificTel: +852 2892 0990Fax:+852 2892 0770
EMEATel: +49 7121 86 2222Fax:+49 7121 86 1222
www.jdsu.com
DSAM Field View QAM™ December 2012