Dosar Tehnic Usi Metalice 2010
-
Upload
iosif-babias -
Category
Documents
-
view
221 -
download
0
Transcript of Dosar Tehnic Usi Metalice 2010
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
1/72
MULTIUSE, EI260 , EI290, EI2120
13
STANDARD DOOR
UNE-EN 1634-1, UNI 9.723, NF y PN
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
2/72( Ed_ 07/06 )
MULTIUSE Single leaf and double leaf
Left hand opening (SX) Right hand opening (DX)
14
SINGLE LEAF DOUBLE LEAF
Left hand opening (SX) Right hand opening (DX)
STANDARD HARDWARE
- Standard lock CR1 TESA model CF50, CEN 12209 (See Lock Section, page 85)
- Multiuse B-05 hinge Galvanized steel material (See Hinge Section page 74)
- Multiuse M0 handles Polypropylene material black color
OPTIONAL HARDWARE
-Panic bar CEN 1125 (See Panic Bar Section, page 91)
-Door-closers CEN 1154 (See Door Closers Section page 115)
-Closer selector CEN 1158 (See section Hingepage 74)
CERTIFICATE
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
3/72
LINEA
CLASSIC
Multiuse single leaf
( Ed_ 07/06 )
MC3 frame is manufactured with a1.2mm high resistant steel and completed cold smoke seal.
rame provided with 4 dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
ver this height the frame is provided with 6 dead-end clamps.
he doors of a nominal height over 2400mm are provided with an additional hinge.
eaf of 53mm thick; manufactured in galvanized steel of 0.5 mm skin pass type.
xpansible Polystyrene, 51mm thickness.CEN approved lock and cylinder patent key
15
FINISHES
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
FRAMES
MC3 (Standard) Type "B" Type "C" Type "M"
HORIZONTAL SECTION OF A LEAF
VERTICAL SECTION
Finished Floor
STANDARD FRAME FIXATION
WITH CLAMPS
4 Clamps of 1,5 mm
OPTIONAL
Fixed with 12 screws (6 for fitting)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
* For technical description of these finishes see page 47.
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel
* For technical description of these accessories see page 90.
DESCRIPTION
H=N
ominalheightoftheleaf
Lt= Width of external frame
L= Nominal width of the leaf
Lp= Clear opening
Lfm= Overall aperture
Ht=
Heigtofexternalframe
Hp=ClearOpening
H
fm=Overallaperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
4/72
LINEA
CLASSIC
Multiuse double leaf
( Ed_ 07/06 )
-MC3 frame is manufactured with 1.2mm high strength steel and completed with cold smoke seal.
-Frame provided with 11 dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
Over this height the frame is provided with 13 dead-end clamps.
-The doors of a nominal height over 2400mm are provided with and additional hinge per leaf.
-Leaf of 53mm thick; manufactured in galvanized steel of 0.5 mm skin pass type.
-Expansible Polystyrene, 51mm thick.-CEN approved lock and cylinder patent key.
-Second leaf manufactured with superior and lower locks with manual activation.
-Instructions for fitting and maintenance
-Leaf weight, 18kg/m2
16
HORIZONTAL SECTION OF A LEAF
VERTICAL SECTION
Finished Floor
STANDARD FRAME FIXATION
WITH CLAMPS
11 Clamps of 1,5 mm
OPTIONAL
Fixed with 15 screws (6 for fitting and 3 in the lintel)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
FRAMES
Type "B" Type "C" Type "M"
* For technical description of these finishes see page 47.
FINISHES
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel
* For technical description of these accessories see page 90.
MC3 (Standard)
DESCRIPTION
L2= Secondary nominalwidth of the leafL1= Primary nominal width of the leaf
Lt= Width of external frame
Lp= Clear opening
Lfm= Overall aperture
H=Nominalheightoftheleaf
Ht=Heigtofexternalframe
Hp=ClearOpening
Hfm=Overallaperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
5/72
-Three sides MC3 frame manufactured with 1.2mm high resistance steel and completed with cold smoke seal.
-Frame provided with 6 dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
Over this height, the frame is provided with 8 dead-end clamps.
-The doors of a nominal height over 2400mm are provided with and additional hinge.
-Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 53 mm thickness.
-Rock wool insulation.
-Intumescent seal in EI2 60:20 x 2mm frame.
-CEN approved EI hinge.
-CEN approved lock and cylinder patent key.
- DIN standard Fire resistant door handles provided in steel core of Polyamide.
-1 anti-crow bar device
-Separators to facilitate an easy installation.
-Metallic identification sheet with standardization EI2
-Full instructions for fitting and maintenance of the unit are provided.
- Door leaf weight 25 kg/m2.
LINEA
CLASSIC
EI260 Single leaf
( Ed_ 07/06 )
17
VERTICAL SECTION
Finished Floor
HORIZONTAL SECTION OF A LEAF
STANDARD FRAME FIXATION
WITH CLAMPS
6 Clamps of 1,5 mm
OPTIONAL
Fixed with 12 screws (6 for fitting)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
FRAMES
Type "B"
* For technical description of these finishes see page 47.
FINISHES
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel
* For technical description of these accessories see page 90.
MC3 (Standard)
DESCRIPTION
H=Nominalheightoftheleaf
Ht=Heigtofexternalframe
Hp=C
learOpening
Hfm=O
verallaperture
Lt= Width of external frame
L= Nominal width of the leaf
Lp= Clear opening
Lfm= Overall aperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
6/72
-Three sides MC3 frame is manufactured from 1.2mm high strength steel and is completed with cold smoke seal.
-Frame provided with 6 Dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
Over this height the frame is provided with 13 dead-end clamps.
-The doors of a nominal height over 2400mm are provided with and additional hinge per leaf.
-Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 53 mm of thickness.
-Rock wool insulation.-Intumescent seal in EI2 60:20 x 2mm frame.
-CEN approved hinge.
-CEN approved lock.
- DIN standard fire resistant door handles provided in steel core of polyamide.
-1 anti-crow bar device
-Separators to facilitate an easy installation.
-Secondary leaf provided with CR4 and bars with superior and lower closing.
-Metallic identification sheet with standardization EI2
-Full instructions for fitting and maintenance of the unit are provided.
- Door leaf weight 25 kg/m2.
LINEA
CLASSIC
EI260 Double Leaf
18
( Ed_ 07/06 )
HORIZONTAL SECTION OF A LEAF
VERTICAL SECTION
Finished Floor
STANDARD FRAME FIXATIONWITH CLAMPS
11 Clamps of 1,5 mm
OPTIONAL
Fixed with 15 screws (6 for fitting and 3 in the lintel)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
FRAMES
Type "B" Type "C" Type "M"
* For technical description of these finishes see page 47.
FINISHES
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel -
* For technical description of these accessories see page 90.
MC3 (Standard)
DESCRIPTION
L2= Secondary nominalwidth of the leaf
L1= Primary nominal width of the leaf
Lt= Width of external frame
Lp= Clear opening
Lfm= Overall aperture
H=Nominalheightoftheleaf
Ht=Heigt
ofexternalframe
Hp=Clea
rOpening
Hfm=O
verallaperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
7/72
-Three sides MC3 frame is manufactured with 1.2mm high resistant steel and is completed with cold smoke seal.
-Frame provided with 8 dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
Over this height the frame is provided with 10 dead-end clamps.
-The doors of a nominal height over 2400mm are provided with an additional hinge.
-Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 63 mm of thickness.
-Rock wool insulation.
-Intumescent seal in EI2 120:30 x 2mm frame.
-CEN approved hinge.
-CEN approved lock and patent key cylinder.
- DIN standard fire resistant door handles provided in steel core of Polyamide.
-2 anti-crow bar devices
-Separators to facilitate an easy installation.
-Metallic identification sheet with standardization EI2
-Full instructions for fitting and maintenance of the unit are provided.
- Door leaf weight 30 kg/m2.
LINEA
CLASSIC
EI2120 Single leaf
( Ed_ 07/06 )
FRAMES
MC3 (Standard)Stainless
steel MC3 Type "C" Type "M"Stainless stee
Type "B"
19
VERTICAL SECTION
Finished Floor
HORIZONTAL SECTION OF A LEAF
STANDARD FRAME FIXATIONWITH CLAMPS
8 Clamps of 1,5 mm
OPTIONAL
Fixed with 15 screws (6 for fitting)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
FINISHES
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel
* For technical description of these accessories see page 90.
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
STAINLESS STEEL, frame and sheet are presented in fingerprint-resistant stainless steel AISI 304
DESCRIPTION
H=Nominalheightoftheleaf
Ht=
Heigtofexternalframe
Hp=ClearOpening
Hfm=Overallaperture
Lt= Width of external frame
L= Nominal width of the leaf
Lp= Clear opening
Lfm= Overall aperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
8/72( Ed_ 07/06 )
-Three sides MC3 frame manufactured with 1.2mm high resistant steel and completed with cold smoke seal.
-Frame provided with 13 dead-end clamps of 1.5 thickness with a maximum of 2400mm height.
Over this height the frame is provided with 15 dead-end clamps.
-The doors of a nominal height over 2400mm are provided with an additional hinge per leaf.
-Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 63 mm thickness.
-Rock wool insulation.
-Intumescent seal in EI2 120:30 x 2mm frame.
-CEN approved EI hinge.
-CEN approved lock and cylinder patent key.
- DIN Standard Fire resistant door handles provided in steel core of Polyamide.
-2 anti-crow bar devices
-Separators to facilitate an easy installation.
-Metallic identification sheet with standardization EI2
-Full instructions for fitting and maintenance of the unit are provided.
- Door leaf weight EI2 120 30 kg/m2.
EI2120 Single leaf
20
HORIZONTAL SECTION OF A LEAF
VERTICAL SECTION
Finished Floor
STANDARD FRAME FIXATIONWITH CLAMPS
13 Clamps of 1,5 mm
OPTIONAL
Fixed with 15 screws (6 for fitting and 3 in the lintel)
SCREWS NOT INCLUDED
FIXED WITH SCREWS
FRAMES
Type "B" Type "C" Type "M"
* For technical description of these finishes see page 47.
FINISHES
* For technical description of these finishes see page 47.
ACCESSORIES
- MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel
* For technical description of these accessories see page 90.
CLASSIC, frame and leaf is provided in RAL 7035.
GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range
INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system
STAINLESS STEEL, frame and sheet are presented in fingerprint-resistant stainless steel AISI 304
MC3 (Standard)
DESCRIPTION
L2= Secondary nominalwidth of the leafL1= Primary nominal width of the leaf
Lt= Width of external frame
Lp= Clear opening
Lfm= Overall aperture
H=
Nominalheightoftheleaf
Ht=Heigtofexternalframe
Hp
=ClearOpening
Hfm=Overallaperture
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
9/72( Ed_ 07/06 )
Single leaf standard doors:Multiuse, EI260, EI290, EI2120
21
VERTICAL SECTION
Finished Floor
HORIZONTAL SECTION OF A LEAF
1075
1025
FRAME DIMENSIONS MC3
DIMENSIONS
H=Nominalh
eightoftheleaf
Ht=Heigto
fexternalframe
Hp=ClearO
pening
Hfm=Overallaperture
Lt= Width of external frame
Ht=Heigtofexternalframe
Lt= Width of external frame
L= Nominal width of the leaf
Lp= Clear opening
Lfm= Overall aperture
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
10/72
STANDARD DIMENSIONS
( Ed_ 07/06 )
Standard single leaf doors:Multiuse, EI260, EI2120
Internal FrameLp x Hp
Internal FrameLp x Hp
Internal FrameLp x Hp
22
Nominal leaf Overall apertureLfm x Hfm
Clear openingLp x Hp
External frameLt x Ht
Overall aperture External FrameLt x Ht
Clear openingLp x Hp
NominalL x H
TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions:To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm)as follows:
Clear openingOverall aperture
Lfm x HfmExternal Frame
Lt x HtNominal leaf
L x H
TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions:To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and(Hfm) as follows:
GENERAL DIMENSION TABLE
For these dimensions, a tolerance of 3mm is applicable.
Internal FrameLp x HpNominal leaf
Overall apertureLfm x Hfm
Clear openingLp x Hp
External frameLt x Ht
MC3 FRAME DIMENSIONS
L x H (L+50) x (H+34)(L-85) x (H-33,5)L x (H+10)
800 x 2050
890 x 2050
990 x 2050
1100 x 2050
1200 x 2050
1300 x 2050
800 x 2140
890 x 2140
990 x 2140
1100 x 2140
1200 x 2140
1300 x 2140
800 x 2060
890 x 2060
990 x 2060
1100 x 2060
1200 x 2060
1300 x 2060
800 x 2150
890 x 2150
990 x 2150
1100 x 2150
1200 x 2150
1300 x 2150
715 x 2016,5
805 x 2016,5
905 x 2016,5
1015 x 2016,5
1115 x 2016,5
1215 x 2016,5
715 x 2106,5
805 x 2106,5
905 x 2106,5
1015 x 2106,5
1115 x 2106,5
1215 x 2106,5
850 x 2084
940 x 2084
1040 x 2084
1150 x 2084
1250 x 2084
1350 x 2084
850 x 2174
940 x 2174
1040 x 2174
1150 x 2174
1250 x 2174
1350 x 2174
Lfm x Hfm Lfm x (Hfm-10)(Lfm-85) x (Hfm-43,5)(Lfm+50) x (Hfm+24)
Lp x Hp (Lp+85) x (Hp+33,5)(Lp+135) x (Hp+67,5)(Lp+85) x (Hp+43,5)
(L-15) x (H+3)
785 x 2053
875 x 2053
975 x 2053
1085 x 2053
1185 x 2053
1285 x 2053
785 x 2143
875 x 2143
975 x 2143
1085 x 2143
1185 x 2143
1285 x 2143
(Lfm-15) x (Hfm-7)
(Lp+70) x (Hp+36)
DIMENSIONS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
11/72
L1 = PrimaryNominal width L2 = Secondarynominal width
( Ed_ 07/06 )
23
Standard single leaf doors:Multiuse, EI260, EI2120
VERTICAL SECTION
Finished Floor
HORIZONTAL SECTION OF A LEAF
1075
1025
internomarco
MC3 FRAME DIMENSIONS
H=Nominalheightoftheleaf
Ht=Heig
tofexternalframe
Hp=ClearO
pening
Hfm=Overallaperture
Lt= Width of external frame
Ht=Heigtofe
xternalframe
Lpa= Primary clearopening
L2= Secondary nominalwidth of the leaf
L1= Primary nominal width of the leaf
Lt= Width of external frame
Lp= Clear opening
Lfm= Overall aperture
DIMENSIONS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
12/72
External FrameLt x Ht
STANDARD DIMENSIONS *for the case of double leaf EI2 120; 10 mm shall be added
( Ed_ 07/06 )
Internal FrameLi x Hi
Internal FrameLi x Hi
24
Standard single leaf doors:Multiuse, EI260, EI2120
Nominal leaf Overall apertureLfm x Hfm
Clear openingLp x Hp
TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions:To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm)as follows:
Clear opening Overall apertureLfm x Hfm
External FrameLt x Ht
TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions:To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and
(Hfm) as follows:
GENERAL DIMENSION TABLE
For these dimensions, a tolerance of 3mm is applicable.
Internal FrameLp x Hp
Clear openingLp x Hp
Overall apertureLfm x Hfm
Internal FrameLi x HiOverall aperture
External FrameLt x Ht
Clear openingLp x Hp
(L1+ L2) x H (L1+ L2+60) x (H+34)(L1+L2-78) x (H-33,5)(L1+L2+10) x (H+10)
Lfm x Hfm (Lfm-10) x (Hfm-10)(Lfm-88) x (Hfm-43,5)(Lfm+50) x (Hfm+24)
Lp x Hp (Lp+78) x (Hp+33,5)(Lp+138) x (Hp+67,5)(Lp+88) x (Hp+43,5)
600+590* (1190*) x 2050
800+400 (1200) x 2050
650+640* (1290*) x 2050
890+400 (1290) x 2050
700+690* (1390*) x 2050
990+400 (1390) x 2050
750+740* (1490*) x 2050
800+790* (1590*) x 2050
890+880* (1770*) x 2050
990+980* (1970*) x 2050
600+590* (1190*) x 2140
800+400 (1200) x 2140
650+640* (1290*) x 2140
890+400 (1290) x 2140
700+690* (1390*) x 2140
990+400 (1390) x 2140
750+740* (1490*) x 2140
800+790* (1590*) x 2140
890+880* (1770*) x 2140
990+980* (1970*) x 2140
1200* x 2060
1210 x 2060
1300* x 2060
1300 x 2060
1400* x 20601400 x 2060
1500* x 2060
1600* x 2060
1780* x 2060
1980* x 2060
1200* x 2150
1210 x 2150
1300* x 2150
1300 x 2150
1400* x 2150
1400 x 2150
1500* x 2150
1600* x 2150
1780* x 2150
1980* x 2150
513
713
563
803
613903
663
713
803
903
513
713
563
803
613
903
663
803
903
903
1112* x 2016.5
1122 x 2016.5
1212* x 2016.5
1212 x 2016.5
1312* x 2016.51312 x 2016.5
1412* x 2016.5
1512* x 2016.5
1692* x 2016.5
1892* x 2016.5
1112* x 2106.5
1122 x 2106.5
1212* x 2106.5
1212 x 2106.5
1312* x 2106.5
1312 x 2106.5
1412* x 2106.5
1512* x 2106.5
1692* x 2106.5
1892* x 2106.5
L1 - 87 (L1+L2-2) x (H+3)
1188* x 2053
1188 x 2053
1288* x 2053
1288 x 2053
1388* x 20531388 x 2053
1488* x 2053
1588* x 2053
1768* x 2053
1968* x 2053
1188* x 2143
1188 x 2143
1288* x 2143
1288 x 2143
1388* x 2143
1388 x 2143
1488* x 2143
1588* x 2143
1768* x 2143
1968* x 2143
(Lfm-12) x (Hfm-7)
(Lp+76) x (Hp+36)
MC3 FRAME DIMENSIONS
DIMENSIONS
Nominal leaf(L1+L2) x H
External FrameLt x Ht
1250* x 2084
1260 x 2084
1350* x 2084
1350 x 2084
1450* x 20841450 x 2084
1550* x 2084
1650* x 2084
1830* x 2084
2030* x 2084
1250* x 2174
1260 x 2174
1350* x 2174
1350 x 2174
1450* x 2174
1450 x 2174
1550* x 2174
1650* x 2174
1830* x 2174
2030* x 2174
Primary clearopening Lpa
Nominal leaf(L1+L2) x H
Nominal leaf(L1+L2) x H
Primary clearopening Lpa
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
13/72
LINEA
CLASSIC
With MC3 and Rever frames, 180, 125 and 90
( Ed_ 07/06 )
25
All the measures are approximated and are expressed in mm
INSTALLATION FOR APERTURE UP TO 180(It is necessary to be fitted into the wall)
Lfm
Lp= Lfm - 85
Lfm + 25
Door-closer
175 (*)
25(*)
INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 125
800
890
990
1100
1200
1300
460
520
570
640
690
750
STANDARD DIMENSIONNOMINAL
WIDTHD
Lp= Lfm - 85
LfmD (**)
(**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges.
If the door includes a panic bar, maximum clear opening will not be obtained
INSTALATION IN CORRIDOR - APERTURE UP TO 9090 aperture in corridor of excellent width(It is not required to be fitted into the wall)
90 aperture in a corridor with a minimum width(It is required to be installed into the wall)
Some handles and door closers can require the fitting into the wall. The installation ALWAYShas to be studied and approved by the Construction department
Lfm
Lp = Lfm -85 -A-BA B
50Cierrapuertas
50
Width of corridor= Lfm +150
Lfm
Lp = Lfm -85 -A-BA B
Cierrapuertas
Width of corridor= Lfm +80
A= 29 for EI20-120A= 19 for EI2-60
B= differs depending on the handle or the installed bar (see accessories section).(example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1)
85 50
L - 230 (*)
175
L-190
L= Lfm
(*) Measures for PUERTAS PADILLA standard handle
SINGLE LEAF APERTURE
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
14/72
LINEA
CLASSIC
( Ed_ 07/06 )
26
400
600
700
800
890
990
240
360
420
470
530
580
NOMINALWIDTH, L2 D2
Lfm
Lp = Lfm - 88
L2 + 70L1 + 25
25
175
Cierrapuertas Cierrapuertas
600
700
750
800
890
990
350
410
440
460
520
570
STANDARD DIMENSIONOMINAL
WIDTH, L1 D1
Lfm * D2* D1
Lp = Lfm - 88
Lfm
Lp = Lfm - 88 - 2x(A+B)A B
5050
Lfm
Lp = Lfm - 88 - 2x(A+B)A B
25
175
8585
50
50
ABAB
L1-190
L1 - 230
With MC3 and Rever frames, 180, 125 and 90
All the measures are approximated and are expressed in mm
INSTALLATION FOR APERTURE UP TO 180(It is necessary to be fitted into the wall)
INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 125
STANDARD DIMENSION
(**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges.
If the door includes a panic bar, maximum clear opening will not be obtained
INSTALATION IN CORRIDOR - APERTURE UP TO 9090 aperture in corridor of excellent width(It is not required to be fitted into the wall)
90 aperture in a corridor with a minimum width(It is required to be installed into the wall)
Width of corridor= Lfm +150 Width of corridor= Lfm +80
Some handles and door closers can require the fitting into the wall. The installation ALWAYShas to be studied and approved by the Construction department
A= 29 for EI20-120A= 19 for EI2-60
B= differs depending on the handle or the installed bar (see accessories section).(example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1)
(*) Measures for PUERTAS PADILLA standard handle
DOUBLE LEAF APERTURE
STANDARDDOORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
15/72( Ed_ 07/06 )
MC3 - MULTIUSE / EI260
With fire certificate
MC3 - EI2120
67,5
43
33
54
13
13
67,5
43
33
64
13
13
MC3 FRAME
-Standard frame in all doors
-Manufactured in steel of 1.2mm thick
WITH CLAMPS
Available in 2 fixing ways
FIXED FOR SCREWS
SCREWS NOT INCLUDED
MARCO MC3
FRAMES
48
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
16/72
MC3 FRAME SUPLEMENT
MC6 SUPPLEMENT: these pieces, welded or screwed, help the MC3 frame to have a better depth or transform the frame into an embracing
frame.
There are several options:
MC6/AAND MC6/B OPTIONS, AT A WALL LEVEL SUPPLEMENT.
They enlarge the wall making it deeper
Weldedsuplement
MC6/C and MC6/D, EMBRACING WALL supplement
It transforms the MC3 frame into Embracing frame.
With fire certificateThe screwing supplements for its installation are sent dismounted by the client
Frame with clamps
MC6/A
Screwed frames
MC6/AA
ScrewedSupplement
Welded frame
Screwed frame
MC6/DAMC6/D
MC6/C
MC6/BAMC6/B
FRAMES
wall thickness -54
d
wall thickness -64
wall thickness -31
d
wall thickness -41
50
65 mm
75 mm
* any request of MC6/D or MC6/DA inferior tothis wall thickness dimension must be seek advice
from the Technical Department.
65 mm
MINIMUM THICKNESS OFTHE WALL
75 mm
Weldedsuplement
Screwed
Supplement
* any request of MC6/D or MC6/DA inferior tothis wall thickness dimension must be seek advice
from the Technical Department.
MINIMUM THICKNESS OFTHE WALL
EI260
EI290EI2120
PROFILEMC6/C-D
d
65
10
30
PROFILEMC6/A-B
33
30
10
d
EI260
EI290EI2120
Multiuse, EI260
EI290, EI2120
Multiuse, EI260
EI290, EI2120
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
17/72
61
FINISHES
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
18/72
EI260 / EI290 / EI2120
MULTIUSE
62
GAMACOLOR
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
19/72
-The three sides epoxy polymerized coated MC3 frame is manufactured high resistant steel and is completed with a cold smoke seal.
- Leaf of zinc-coated sheet, PVC laminated or painted in different finishes according to RAL color chart with 53mm thick for EI2 60
and MULTIUSE and 63mm for EI2 90 and EI2 120.
-The doors of a nominal height over 2400mm are provided with and additional hinge.
-Rock wool insulation
EI2 60: 150kg/m3, 50 thickness
Ei2 90: 150kg/m3, 60 thickness
Ei2 120: 180kg/m3, 30 +30 thickness
MULTIUSE: expansible polystyrene or aluminum bee nest design, 52mm thickness.
-Secondary leaf seal EI 60: 33 x 2mm, EI2 120: 43 x 2mm.
- CEN approved EI hinges.
- CEN approved lock.
-Fire-resistant DIN handle with anti-coupling, completed with a polyamide fire-proof steel core. For multiuse doors, the handle is made out of plastic.
-Anti-crowbar device: E12 60, one device per leaf; EI 2 90 and EI2 120, two devices per leaf. Multiuse doors are not provided with anti-crowbar device.
- The frame is provided with 11 dead- end clamps for EI2 60, 13 for EI2 90 and EI 120 and 11 for multiuse doors.
- Closer selector EI2 120, optional in EI2 60
-Separators for the installation.
-Instructions for fitting and maintenance
-Door leaf weight
EI2 60: 25kg/m2
EI2 90: 28.5kg/m2
EI2 120: 30kg/m2
Multiuse: 18kg/m2
Left hand opening (SX) Right hand opening (DX)
( Ed_ 07/06 )
Double leaf door
64
Anti-crowbar device HandleLock Intumescent seal
FINISHES
GAMACOLOR
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
20/72( Ed_ 07/06 )
EI260, EI290, EI2120, Multiuse
65
STANDARD EPOXY-POLYESTER GOFFERED RAL CHARTFRAME-LEAF COLOUR CORRESPONDENCE.
PVC RANGE.RAL textured finish frame
FINISHES
GAMACOLOR
Maximum dimensions per leaf: L (400 - 1300) and H (1250 - 2550)
The colour reproduced in the brochure may be slightly inaccurate due to printing reasons. It is recommended that a RAL colour chart is used when specifying colours.
Between the frame and the leaf a different tonality can be presented, this may result from the differences
of the finishes and the process of paint coat.
Every PVC colour for the door leaf, can be only provided with its corresponding RAL colour for the frame,
according to the enclosed chart. It only can be manufactured with these combinations and the doors
cannot be provided with different colour combinations between the frame and the leaf.
The doors with different colours for each side of the leaf are not provided.
- Extra charge depending on the colour.
ROBLE
PINO
HAYAROBLE NUEVO SAPELLYTANGANIKA
NOGAL WENGUECEREZO
MAXIMUM DIMENSIONS PER LEAF:
-EI260 L (400 - 1100) y H (1250 - 2950)
-EI290 L (400 - 1090) y H (1250 - 2900)
-EI2120 L (400 - 1090) y H (1250 - 2900)
Ral 8017 textured finish frame.
RAL 7038
RAL 1013 RAL 5010 RAL 7024RAL 6034
RAL 7035
RAL 9001
RAL 9003RAL 9002 RAL 9010
RAL 9018
RAL 5024 RAL 8011
RAL 9007 LISORAL 9011RAL 3000
RAL 1003
RAL 6000RAL 6005
DL10
DL76DL1
DL36CEDL64
DL88DL65
DL78SME
DL21C
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
21/72( Ed_ 07/06 )
EI260, EI290, EI2120, Multiuse
66
PVC RANGE.
ALUMINIUM AND STAINLESS STEEL COLOR
FINISHES
GAMACOLOR
CREAM
RED
BLUE
YELLOW
DARK GREEN
LIGHT BLUE
GREEN TURQUOISE
IVORY
GRAPHITE BLACK
GRAPHITE GREASE
MAROON
WHITE
ALUMINIUM GREASE ALUMINIUM STAINLESS STEEL
Frame finished in RAL plain 9007.
Maximum dimensions per leaf: L (400 - 1090) y H (1250 - 2950)
Maximum dimensions per leaf: L (400 - 1090) y H (1250 - 2950)
The colour reproduced in the brochure may be slightly inaccurate due to printing reasons. It is recommended that a RAL colour chart is used when specifying colours.
R8SMA
B1
R24SMAM
A56SMA
V8SME
N12SM
B35SMA
G11SM
N3SMA
A17SMA
V36SMA
A47SMA
F23SMA F16 PPS F12PPS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
22/72
74
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
23/72
BISAGRAS
BISAGRAS
-This hinge is assembled with a hinge screw, a gasket and a bearing that make possible themovement of the leaf.- In REVERSIBLE doors the gasket can be replaced by another bearing to ensure the reversible
feature.- For RIGHT opening hand, this hinge is locates in the inferior part of the frame. For LEFT openinghand it is located in the upper part.- With this hinge it is possible to increase the leaf height 1.25mm or 2.500, by inserting 1 or 2 extragaskets respectively (See Instructions. Adjustment of the leaf height).-Hinge manufactured according to DIN 18272-CE approved according to the norm EN 1935.
( Ed_ 07/06 )
B01, DIN HINGE WITH BEARING
STEEL 3 mm THICKNESS
75
BEARING GASKET HINGE SCREWWITHOUT SPRING
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
24/72
BISAGRAS
BISAGRAS
-This hinge is assembled with a hinge screw provided with a spring and a tension retainerthat help the closing of the frame.- For RIGHT opening hand, this hinge is located in the upper part of the frame. For LEFTopening hand is in the inferior part.- Those doors with a third hinge, this one is always a hinge with automatic closer.-Hinge manufactured according to DIN 18272.
( Ed_ 07/06 )
B02, DIN HINGE WITH AUTOMATIC CLOSER
76
STEEL 3 mm THICKNESS
HINGE SCREW WITH ANAUTOMATIC CLOSER SPRING
RETAINER FOR FIXING THE TENSIONOF THE AUTOMATIC CLOSER SPRING
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
25/72
BISAGRAS
SAGRA INOX REGULABLE
This hinge includes, in its fitted frame, a regulation system of the leaf with
three positions:
-Height
-Support distance of the leaf over the frame.
- Lateral looseness between the leaf and the frame (it makes possible to adjust
the leaf nodding).
-It includes a bearing system that makes easier the movement of the leaf.
-CE approved according to EN 1935-14.
( Ed_ 07/06 )
B04, STAINLESS STEEL SPECIAL HINGE
Stainless steel special hingeHinge regulation systemintegrated in the frame
77
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
26/72
BISAGRAS
BISAGRA INOX
-This standard hinge is installed in the STAINLESS STEEL range doors.
-To install different kind of frame of the Stainless steel range, seek advice forthe Technical Department.
-It is integrated with a bearing system that makes easier the movement of the
leaf.
-CE approved according to EN 1935-14.
( Ed_ 07/06 )
B03, STAINLESS STEEL HINGE
78
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
27/72
BISAGRAS
BISAGRA MULTIUSOS
-This hinge is installed in multiuse leaf doors
( Ed_ 07/06 )
B05, MULTIUSE HINGE
79
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
28/72
BISAGRAS
BISAGRA MULTIUSOS
-Hinge of stainless steel finish
( Ed_ 07/06 )
BM0, STAINLESS STEEL HINGE
80
HARDWARE
HARDWARE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
29/72
81
HANDLES
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
30/72
Stainless steel satin
F1 finish. Aluminium
HANDLES: Opening door device, it can also be combined with a panic
bar which activate the lock located in the leaf. It is installed in all primary
doors and single leaf door.
EI2 DOORSThe handle provided as a standard is the M1 model black colour. A
different kind of handle included in this technical catalogue can be
provided.
M1: Standard fire door handle
-According to DIN 18255.
-Steel core
-Handle diameter: 20mm or 23mm
Anti-coupling fire door handle according to DIN, made of fire-proof
polyamide with steel core.
DIFFERENT FINISHES- ONLY IN EI2
It can be provided in stainless steel or aluminiumF1 finish. aluminium
MULTIUSE DOORS
For multiuse doors, a M0 handle range in black colour shall be provided.
M1 : Standard fire door handle
HANDLE
HANDLES
82Handle M1Handle M1 Handle M0
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
31/72
Handle for WATER lock
Fix knob. Operation by key from both sides.
KIT GARAGE Operation from one side handle.Fix knob, incorporates key and it operates fromboth sides.
Fix knob Rosette model.
Operation by key on bothsides, black colour.
Handle for ISABEL II lock
Fix knob, blind plate. Operation by key fromboth sides
Standard door handle incorporating patentcylinder lock fitting. Handle operation fromboth sides.
Cover plate on both sides. No door handleoperation
Standard handle, operation from both sides.Without lock feature
Evacuation
Evacuation
Multiuse door handle for multiuse doorsincorporating patent cylinder lock fitting. Handleoperation from both sides.
HANDLE
83
HANDLE
M10
M8
M6
M11
M7
M0 M1
M4
M3
M12
M2
Condenable por cilindro
Evacuacin
Antipanic handle (to push) with condenablehandle and operation with key on both sides.
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
32/72
1. Select the parts to be fitted according to the EI range of the door;
the parts for 60/120 are common for both thickness.
2.The parts with rectangle shape have to be fitted on the hinge sidethose of half cylinder shape go on the opposite side of the hinges.
3. Locate the square shape piece 1 upwards, right through the
superior cylinder lock and fit the piece 2 with the piece 1 (half
cylinder upwards).
4. Insert the piece 3 in the inferior square hole with the rectangle
shape upwards.
5. Insert the piece 4 in the inferior in the square hole (half cylinder
upwards).
6.Clamp the handles to the handle linkage shafts with the two grubscrews located in the handles.
7.Once they have been fitted, the plastic cover will be placed.
DOOR HANDLE FITTING INSTRUCTIONSHARDWARE
84
HANDLE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
33/72
85
LOCKS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
34/72
SPECIAL PANIC LOCK
-CE Marked
-Reversible
-Adjustable latch for easy opening
-Anti-panic function with condenable by key exterior handle
-Square bar steel 9 mm-Entrance 65mm
PADILLA EMERGENCY LOCK
-Din lock
-Reversible
-Adjustable latch for easy opening
-Anti-lock system (It is not possible to lock the evacuation paths,
according to NBE CPI-91)-Square bar steel, 9mm
-Entrance 65mm
STANDARD LOCK
CF 50 MODEL, CE EN 12209
-Reversible lock
-Condenable in both sides-Square bar steel, 9mm
-Entrance 65mm
FOR SINGLE OR ACTIVE DOOR
Single leafActive leafof doubleleaf door
Passive leafof a doubleleaf door
HARDWARE
CR7
BARREL LOCK
-Barrel lock
-Opening device (PUSH-PULL)-Not available for certified doors
LOCKS
86
CR1
CR2
CR3
CR 7
A
A P
For those doors with fitted panic bar, the lock shall not be installed
LOCKS: device that make possible to keep the doorin a closed position
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
35/72
MANUAL FLASH BOLT
-Passive leaf closer
-Automatic device with 2 closing points
-Manual opening
-CE Marked
PASSIVE LEAF LOCK
CR5 CONTRA-LOCK
(anti-panic)
-Anti-panic closing for passive leaf
-Automatic device with 2 closing points
-Opening through panic bar
-CE Marked
With both locks the superior and inferior passive leaf closing can be performance by the screwed rods.
PT1 LATCH PT1
-Closing for passive leaf-Superior and inferior latch with manual operation
Screwed rods for
CR 4 y CR 5:
87
Single leafActive leafof doubleleaf door
Passive leafof a doubleleaf door
LOCKS
HARDWARE
CR 4
CR 5
P
PT 1
A P
Only available for multiuse double leaf doors
As an optional choice for passive leaf doors, we provide a floor limiter for the inferior bar of thesecondary leaf
TP1 Floor limiter for secondary leaf
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
36/72
HARDWARE ELECTROMECHANICAL LOCK
88
HARDWARE
ELECTROMECHANICAL LOCK: are locks which opening is controlled by a switch or control device. This device supplies 12Vdc to the
lock allowing it to open.
These locks are for single or active leaf of double leaf doors.
There are two types:
CR1E; electromechanical fireproof standard lock
CR3E; electromechanical fireproof lock for panic bar
Operation information
a) As long as the inductor is properly feed, with adequate tension and polarity, it can be open by using the handle of any of the side door;
even if the door is locked.
b) Without tension;
-CR1E model it will never open if the door is locked (with the key).
-C33E model, it wont open from the hinge side if the door is locked (with the key). From the panic bar side
(opposite to the hinges) this lock can be open at any time.
NOTE: There will be only electrical tension, when the electric power supply is active.
with
12Vdc
Both handles open
CR1E
None of handles open
CR1E
CR3E
Handle doesn t open-Baropens
CR3E
Handle opens-Bar opens
DOOR LOCKED DOOR UNLOCK
Both handles open
CR1E
CR3E
Handle opens-Bar opens
Both handles open
CR1E
CR3E
Handle opens-Bar opensWithout
12Vdc
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
37/72
Pictures of the finishing of the anti-vandalism rollaway cable.
HARDWARE ROLLAWAY WIRED TUBE
89
HARDWARE
The rollaway wired tube, go through the leaf from the opposite side of the lock and is connected by an anti-vandalism cable with the frame. The
above mentioned cable has been designed to guarantee the continuous transference of the cable between the door and frame.
-Anti-vandalism rollaway cable, it remains hidden when the leaf is closed.
-It accepts cables up to 7mm diameter.
-Tube and cover plate made of stainless steel.
-It is possible to build in the leaf of the door
PS-1(Anti-vandalismrollaway cable)
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
38/72
NOVACLASS
CLASSIC
GAMACOLOR
ACSTICA
INOX
ACCESORIOS
ACCESSORIES
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
39/72
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
40/72
AC
CESSORIES
ACCESSORIES
Panic bar SR range
Panic bar T range
Touch bar
Techno bar
Techno plus bar
92
PANICBAR
PANIC BARS: The anti-panic device is a device for opening doorslocated in Emergency exits of public places where a panic situationcan occur.
It opens outwardsPANIC BARS TYPESPuertas Padilla S.L. offers 5 different types of Anti-panic devices
-Panic bar SR range: it works by activating the CR3 standard lockthat is inserted in the leaf interior.
-Panic bar T range: the bar itself has a door handle system thatworks as a lock, the lock is not necessary in the leaf.
-Touch bar: it works by activating the lock inserted in the leaf, as
the case of the first type, but its dimensions are smaller makingpossible a bigger space in 90 apertures.
-Techno bar: it works by activating the CR3 standard lock that isinserted in the leaf interior.
-Techno plus bar: it works by activating the CR3 standard lock thatis inserted in the leaf interior.
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
41/72
970 SRABar for passive leaf in double leaf doors.Without the possibility of exterior opening activation.
This bar can be installed if the door has been installed with a CR-5 lock
Exterior opening option. Through thehandle
SR TYPE BAR (TO INLAY)
AVAILABLE OPTIONS
GENERAL CHARACTERISTICS
-Standard colours: red and black
-CE marked
-Manufactured for single and double door
-1 closing point
-Reversible
-Exterior activation in different finishes
CERTIFICATION
Classified according to European certification
EN 1125
Satin Stainless steel chrome plated Brass tonality
970 SR
Single leaf doorActive leaf of double leafdoor passive leaf of doubleleaf door
Exterior opening option. Through handleor key
Without the exterior opening option, withblind plate
Exterior opening option through key and fixedknob
Exterior opening option throughkey
39
208
SR RANGE BARACCESSORIES
93
Single leafActive leafof doubleleaf door
Passive leafof a doubleleaf door
PANICBAR
98
3 7 6 1 1 3 2 2 A
971 SR
975 SR
+
+
++
+ 974 SR
973 SR
972 SR
A
P
A P
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
42/72
30
Panic bar forSingle and activeLeaf of doubleDoor.
T TYPE BAR (TO OVERLAY)
GENERAL CHARACTERISTICS
-Standard colours: black and red
-CE Marked
-Available for single and double doors.
-From 1 to 3 closing points.
-Reversible
-Exterior activation in different kind of finishes.
CERTIFICATION
Classified according to the European certification
EN 1125
Closing points bar forprimary leaf, withoutexterior activation, withblind plate
Closing points bar forprimary leaf, with exterioractivation. Through handleand key
Closing points bar forprimary leaf, with exterioractivation, through handle
3 points barfor singleleaf door
Closing points barfor passive leaf ofdouble leaf doors
39
208
ACCESSORIES T BAR
94
Satin Stainless steel chrome plated Brass tonality
AVAILABLE OPTIONS
Single leafActive leafof doubleleaf door
Passive leafof a doubleleaf door
Exterior opening option. Through thehandle
Exterior opening option. Through handleor key
Without the exterior opening option, withblind plate
Exterior opening option through keyand fixed knob
Exterior opening option throughkey
PANICBAR
3 7 6 1 1 3 2 2 A
913 T
910 T
912 T
+
+
+
+
+ 911 T
915 T
914 T
98
+
+
+ 950
952
953
A P
A
931 T
P
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
43/72
98
VISION PANEL AND GLASS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
44/72
VISIONPANEL
ANDGLASSACCESSORIES VISION PANEL AND GLASS
99
ADDECUATE MAINTENANCE OF THE GLASS
-EI glass have been manufactured for an indoor use, as they become opaque if
the glass is exposed to atmospheric agents or direct sunlight.
-The glass should be washed with lukewarm water, a soft fiber cloth and a
compatible cleaner applied with a spray. Let rinse and wipe away with a soft cloth.
-Do not use any kind of acid, alkaline, chemical substances, solvent or its steam,
abrasives or sharpened objects. It should never be used dirty clothes for cleaning
up the glass.
VISION PANEL: accessory that makes possible to see the through the other
side of the room, it can be fitted in places where there is a frequent transit of
people and the door must be closed due to safety reasons.
TYPES OF VISION PANELS AND GLASS
There are two different types of vision panel; rectangular and circular.
Circular vision panel
Rectangular vision panel
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
45/72
STRATIFIED GLASS FOR MULTIUSE DOORS
Dimensions Cod.
ACCESSORIES STRATIFIED GLASS FOR MULTIUSE DOORS
100
VISIONPANEL
ANDGLASS
V2
V3
V4
300 X 400
600 X 400
280
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
46/72
EI 60 VISION PANEL FOR FIRE DOORS EI 120 VISION PANEL FOR FIRE DOORS
Dimensions Cod. Dimensions Cod.
Fire- proof
ACCESSORIES VISION PANEL EI 60 AND EI 120
GLASS FOR EI260
GLASS FOR EI2120
101
VISIONPANEL
ANDGLASS
V14
V16
V18C
300 X 400
600 X 400
280
300 X 400
600 X 400
280
V21
V23
V25C
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
47/72
VERTICAL LOCATION
As long as the leaf height is lower than 2050, acircular hole will be performed with its center in Cmeasure point. In those doors which dimensionsare smaller, the minimum B dimension will berespected.
HORIZONTAL LOCATIONOn the side part it shall be centered, respecting
always the A minimum measure point as indicatedin previous pages.
ACCESSORIES VISION PANEL LOCALIZATION
102
VISIONPANEL
ANDGLASS
C=1550
=
B= Min. 300=
C=1785
==
B= Min. 300
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
48/72
104
CYLINDERS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
49/72
1.- Mark out the door leaf with the minimum requireddimensions indicated in previous pages.
2.- Drill through the door leaf and then cut the holewith a jigsaw fitted with a fine toothed blade, payspecial attention in order to prevent any delaminationof the door leaf.
3.- Locate as many retaining clips as screws have thesnap fastener ( not less than 4-6) according to theinferior figure. So it can match up with the locationwhere the screws are going to be placed.
4.- Locate the vision panel in the hole with the suppliedself-reaming tapping screws.
5.- Turn the door leaf over to provide access from theother side and place the vision panel into the aperture.
6.-Locate the ceramic fiber insulation blanket onto theedge of the vision panel or the peep hole seal if iscircular.
7.- Fit the glass by locating the Intumescent seal onthe retaining clips until the ideal adjustment is reached.
8.-Locate the second vision frame in the proper positionand screw it on.
9.- Cut out the remaining Ceramic blanket. In case ofrectangular peep hole
VISION PANEL OR PEEP HOLE FITTING: HORIZONTAL SECTION
STEPS TO FIT THE GLASS
CIrcularuntumescent seal
RectangularCeramic blanket
Cristal
Agujero = cristal + 5
Cristal
ACCESSORIES VISION PANEL FITTING
103
VISIONPANEL
ANDGLASS
VISION PANEL OR PEEP HOLE FITTING: VERTICAL SECTION
2.5 2.5
A A
Cristal
2.5
B
C
2.52.5
B
C2.5
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
50/72
74mm Mastered keyed thumb turn cylinder (one mastered key and three keysincluded) (EI2 60/Multiuse)
Patent cylinder (one key included)
85mm metallic cylinder (three keys included) (EI2 120)
75mm 2 sides mastered keyed cylinder (three keys and one masteredkey per set) (EI2 60/Multiuse)
85mm 2 sides mastered keyed cylinder (EI2 120)(three keys and one mastered key per set)
85mm Mastered keyed thumb turn cylinder (one mastered keyand three keys included) (EI2 120)
Metal half cylinder
CYLINDERS: device that makes possible to block the lock so the door cannot be open by
activating the handle.
There are locks; such as CR3 lock that, by using the cylinder, it can only be locked from
outside and with the bar is possible to open the door.
The doors are provided with the C1 lock as a Standard lock
75mm metallic cylinder (three keys included) (EI2 60/ Multiuse)
CYLINDERS
ACCESSORIES CYLINDERS
105
85mm metallic cylinder (three keys included) (EI2 120)
C7/2
C4
C 6
C 7
C4/2
C 6 / 2
C 1
C 2
C 3
C 4
C 6
C 7
10 35
35 10 35
30/40 10 35
30/40 10 35
30/40 10 35
C 3
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
51/72
106
SELECTORS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
52/72
Standard closer selector
Closer selector floor
CLOSE SELECTOR: Device that coordinates the double leaf doors closing to avoid that the primary leaf closes before the secondaryone and the door remains opened
-For active leaf doors with a width over 1000mm this system is not advised. In this case a hydraulic closer selector must be installed
Extra-flat close selector
Flat closer selector
SELECTORS
108
Horizontal section
ACCESSORIES OPEN SELECTOR
SR 90
SC
SCP
SCE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
53/72
1. Before fitting the door in the
wall, screw on firmly the box to the frame
using the screws (A).
2. Once the door is fitted and
regulated, insert the selector in the box
making sure that it goes towards the
primary leaf. Fix it with the screws (B)
that are provided in the box.
3. Adjust the selector by turning
the regulation screw located in the
internal part (and Allen key shall be
required). Ensure the selector makes
contact with the superior corner of the
primary leaf.
4. Check if the device works
properly.
STANDARD Close Selector
Close selector to be integrated in the MC3 frame, it will remain hidden once the leaves are closed.
Reversible
Cylindrical bar, 12mm thickness. It is provided with a spring to absorb the shock in the retention of the primary leaf.
It is fitted on the frame once it has been installed in its box
Regulationscrew (C)
CLOSE SELECTOR FITTING INSTRUCTIONS
close selector installation box
We have available as an option, a cap to cover the frame holes where the selector is installed
PVC plate to cover the holes of the predispositionof the close selector
SELECTOR
ACCESSORIES STANDARD CLOSE SELECTOR
109
B
AA
csc
TSC
To be used onlywith the provided screws
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
54/72
113
ELECTROMAGNETS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
55/72
ELECTROMAGNETS: System that locks the door in open position, in the
event of a fire, the door electromagnet is turned off by pushing the
electromagnet or by the fire alarm system.
Electromagnets are installed in public or crowed places where it should be
a previous barrier against fire.
ELECTROMAGNETS
ELECTROIMANES
114
E 2
P2
P1
E 3
Electromagnet with unlocking system
Power supply: 24Vdc
Absorbed power: 70mA
Tractive effort :> 55kg
According to CE 1155
Telescopic plate for fixing on the flooror wall
Black lacquered steel core
Adjustable 180
Dimensions 140 x 220
Rigid contraplateBlack lacquered metal base
Dimensions 65 x 65 in the base
and 28 height
Diameter: 55
Articulated Contraplate
Black lacquered metal base
Dimensions: 65 x 65 in the base and 28
heightDiameter: 55
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
56/72
115
DOOR-CLOSER
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
57/72
Aluminium reversible door-closer with steel arm.
Tension 2/3/5 (EN1154)
Silver finishing
Fire certificate
Door-closer sizes Door set widthmax.Door setweight
max.Fuerza EN/1-6
1
2
3
4
5
6
DOOR CLOSER DIMENSIONS TABLE
For door-closers with guide is necessary to ask
for the predisposition of the frame or for itsinstallation the guide will be directly screwed onthe wall
The door-closers that are adjusted in tension fromEN 1/2, shall not be fitted in fire doors accordingto EN 1154
Door closers:Controlled closing system of the door. It makes possible to regulate the closing speed and the final shut of the
door. It is installed on doors where the closing must be regulated in order to avoid that the door closes at once and can lead
into a danger for people who make use of it, especially with children and elderly people.
DOOR-CLOSER
Fire Certificate
116
Aluminium reversible door-closer with steel arm.
Tension 1/5 (EN 1154)
Silver finishing
Fire certificate
DOOR-CLOSER
TS-11F
LP - 12
mm
750
850
950
1100
1250
1400
kg
20
40
60
80
100
120
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
58/72
Aluminium reversible door-closer with
steel arm. Tension 3/4 (EN 1154)
Silver finishing
Fire certificate
DOOR-CLOSER
Reversible door-closer with sliding arm
Tension 2/4 (EN 1154)
Silver finishing
Fire certificate
Reinforced with guide door-closer system
Tension 2/4 (EN 1154).
The guide is screwed on the wallSilver finishing
Fire certificate
Fire Certificate
DOOR-CLOSER
117
TS 1500
DORMA TS-92
58
16
50
39
38207
334
55 55
31
TS 12 GUIA39
60
55
493
21,5
221
60
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
59/72
Double leaf door-closers with closing selector incorporated
Tension 2/5 (EN 1154)
Silver finishing
Fire certificate
DOOR-CLOSER
A= according to the width of the nominal leaf.
Double leaf door-closer with closing selector incorporated.
Tension 2/5 (EN 1154)Silver finishing
.
DOOR-CLOSER
118
Fire Certificate
GEZE 3000
TS 93 GSR
275
53
A470
60
31
275
470
6060
DORMA TS 92 GSR
21,5
60
221
60
221
1600 mm / 2000 mm / 2500 mm
39
60
55
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
60/72
119
SEALS
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
61/72
FRAME AND LEAF SEAL LOCATION
All the seals are self-adhesive. Except from the MAC 1
JI 20, JI 30Standard Intumescent seals:Dimensions:
JI20 for EI 60 -20 x 2 mm
JI30 for EI 120 - 30 X 2 mm
JI 35, JI 45
Intumescent seals betweendouble leafDimensions:JI 35 for EI 60 -33 x 2.5 mmJI 45 for EI 120 -43 x 2.5 mm
MAC 1Ceramic blanket betweenglass and vision panel
Dimensions: 30 x 3mm
JF1Cold smoke and anti-noise seal for leafDimensions. 19 x 15mm
Jai1Intumescent Acoustic seal for frameDimensions: 5 x 20mm
JF4Cold smoke seal for frameMC3Dimensions: 28 x 15 mm
SEALS:
Edges of a fire door, usually fitted in the leaf and frame, it providesto the door a thermal or acoustic insulation
SEALS, POSITION
Fire certificatedAcoustic seal
Leaf
Frame
Leaf
Leaf
Leaf
Frame
Leaf
Leaf
Leaf
Frame
Leaf
Leaf
Leaf
Vision panel
K
K
K
K
SEALS
JAi2Intumescent Acoustic seal
between leavesDimensions: 5 x 20mm
K
120
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
62/72
121
LOUVRES
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
63/72
PADILLA STANDARD LOUVRE (RJ 1 )
VERTICAL SECTION
Louvres: Ventilation system installed in multiuse doors to enhance the gas outflow from one place to the other.
LOUVRES
This louvre installation can only be available in Multiuse doorsIf the installation is performed in a fire door, our enterprise wont provide EI door certification.
189,25
101,5
=400=
To install any kind of louvre different from this catalogue, seek for advice in our TECHNICAL DEPARTMENT
LOUVRES
122
12 Rows and 10 columns of 29 x 3 mm
360
80
200
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
64/72
123
KICK PLATE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
65/72
KICK PLATE
KICK PLATE: protector against knocks used in places with access to
trolleys, cart, etc where the door can be pushed violently.
-It protects the sheet of the door
-Made of aluminium or stainless steel of 1mm thickness.
There are two types:
-For the lock area
-For the inferior area of the leaf
-They are always located on the opposite side of the hinges
SINGLE LEAF DIMENSIONS
LOCK LEVEL KICK PLATE INFERIOR KICK PLATE
KICKPLATE
124
A=(B-20)/3
ESP. 1 MMESP. 1 MM
A=(B-20)/3
B=L-93
A
8
6510
25
43.5
10
65
A A
175
10
B=L-93
A10 A A
10
10
220
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
66/72
KICK PLATE
KICK PLATE DIMENSIONS FOR ACTIVE LEAF IN DOUBLE LEAF DOOR
125
KICKPLATE
LOCK LEVEL KICK PLATE INFERIOR KICK PLATE
LOCK LEVEL KICK PLATE INFERIOR KICK PLATE
KICK PLATE DIMENSIONS FOR ACTIVE LEAF IN DOUBLE LEAF DOOR
ESP. 1 MM
A=(B-20)/3
ESP. 1 MM
A=(B-20)/3
10
10 A
B
175
A A 10
10
10 A
220
B
AA 10
A=(B-20)/3
ESP. 1 MM ESP. 1 MM
A=(B-20)/3
B=L-93
A
8
6510
25
43.5
10
65
AA
175
10 AAA10
10
10
220
B=L-93
B=L-28
B=L-28
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
67/72
KICK PLATE
INSTALLATION DETAILS
OPPOSITE SIDE OF THE HINGES
ACTIVE LEAF PASIVE LEAF
126
KICKPLATE
OPPOSITE SIDE OF THE HINGES
aprox. 2.5
aprox. 2.5 aprox. 2.5
aprox. 2.5
220
175
aprox. 2.5
220
175
220
175
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
68/72
127
ELECTRONIC ENTRY-PHONE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
69/72
The installation of this electronic entry phone canonlybe installed in Multiuse doors. If the installationis performed in a fire door, our enterprise wontprovide the EI door certification
ELECTRONIC ENTRY-PHONE:
Device installed in multiuse doors that makes possible to open thedoor by remote control.Only for single leaf door
ELECTRONIC ENTRY-PHONE
ELECTRONIC
ENTRY-PHONE
128
( PE ) ELECTRONIC ENTRY-PHONE
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
70/72
129
ACOUSTIC KIT
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
71/72
Puertas Padilla acoustic kit are a seals set that once installed, in the leaf and frame, gives a better acoustic insulation.
Those kits can be installed in the following doors:
-CLASSIC
-GAMMACOLOUR
-STAINLESS STEEL
INCLUDED
ACOUSTIC INSULATION TABLE ACCORDING TO KIT (MEASURES IN dB)
In single or double leaf doors with vision panel, the glass must be EI2 120 to maintain the acoustic isolation
ACOUSTIC KIT
ACOUSTICKIT
130
WITHOUTKIT
KA 4
KA 5
KA 7
EI260 EI2120
19
37
36
38
20
41
40
42
20
34
36
36
20
35
34,5
33,5
JF1 JF4 JAi1 GS1PP1 PP2
x x x
x x x
x x x
x
x
x
x
DETAIL PP2(Kit KA4)
DETAIL PP1(Kit KA7)
FLOOR SEALS WITHOUT KIT
FLOOR SEALS DETAILS
DETAIL GS1(Kit KA5)
JAi2
x
x
x
-
8/12/2019 Dosar Tehnic Usi Metalice 2010
72/72
COUSTIC KIT FITTING INSTRUCTIONS
HORIZONTAL SECTION
VERTICAL SECTION
ACOUSTICKIT
JF1JF4
PP1
JAi1
JF1
JF4
JAi2
JAi1