DELUXE/TRADITIONAL RAILING INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONSDELUXE/TRADITIONAL RAILING

FHS-0002-LIT 5/15

www.fiberonhomeselect.com800.318.7828

Manufactured by

Deluxe/Traditional Railing Installation Instructions

Required Tools and Supplies:

Deluxe Top Rail Profile Traditional Top Rail Profile• Power Drill • 1/8-in. Drill Bit• #2 Square Head Bit• Protective Eye Wear• Tape Measure• Level

• Screw Driver, Phillips #2• Speed Square• Miter Saw• Pencil• Adjustable Square

Railing component list for each section:

Post SleeveCap

Top Rail Bracket

BracketFlange

Top Rail

Bottom Rail

SquareBalusters

Round MetalBalusters

Round MetalBaluster Insert

Bottom Rail Bracket

YES2-in. minimum from rail end to hole

NO

Post Sleeve

Post Sleeve Collar

CrushBlock

Prior to installing railing: Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. All supporting structures must be in accordance with applicable building codes. Neighborhood associations and/or historic districts may regulate size, type, placement and type of railing. Apply for permits if required by local authorities and codes. Ensure compliance prior to installation. Local building code requirements will always supersede any and all suggested procedures and measurements in the following installation. The following installation instructions are intended as a general guideline based on common building practices used in railing installation.

When railing span is greater than the distance between posts, trim both top and bottom rail ends to maintain uniform baluster spacing. Measure distance, subtract 1/2-in. from measurement (1/4-in. on each side) to allow for brackets and flanges. Slide post sleeve collar over each post prior to installing bottom rails and press securely into place.

After carefully measuring between level and plumb posts, cut top and bottom guardrails to length. Slide bottom rail brackets over ends of bottom rail.

Cover 4x4 posts or Fiberon Homeselect surface mount bracket (Item# 345061) with post sleeve and verify spacing. Posts should be plumb in both directions.

Traditional and Deluxe Bottom Rail Bracket

Traditional Top Rail

Deluxe Top Rail

Center crush block on deck surface between posts. Set bottom rail on top of crush block.

Place the bottom rail between the post sleeves using crush block to support and level the bottom rail.

Traditional Top Rail Bracket

Deluxe Top RailBracket

Rail Installation: Trim both ends of rail to maintain uniform baluster spacing. It is critical to ensure the trim mark does not create an openbaluster Insert hole at the end of the rail where the bracket is attached. Adjust trim lines to maintain uniform baluster spacing

Deluxe/Traditional Rail Installation Instructions

1

2

3

Bottom Rail

Crush Block

Maximum length between posts:6ft Rail = 72-in. - Taditional and Deluxe8ft Rail = 96-in. - Traditional

The most recent installation instuctions can be found our website. Please visit www.fiberonhomeselect.com or call custmer service at 800-318-7828.

Deluxe and Traditional Bottom Rail Profile

NOTE: If using the post sleeve collar, make sure to position and glue collars in place prior to securing the bottom rail.

NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing.

NOTE: For best results, cut post sleeves with a 10-in. circular carbide-tipped blade, minimum 32-tooth.

Note: Fiber Composites LLC actively works to improve the performance and installation of our Lowes’ Fiberon HomeSelect guardrail systems. Recent improvements have been added into the time tested brackets previously supplied to make the Lowes’ Fiberon HomeSelect guardrails even stronger and more adaptable than before. No matter which style, Fiber Composites LLC stands behind the quality and performance of every guardrail system.


If using round metal balusters, insert rail inserts for round balusters into the top and bottom rail routed holes. Place round metal baluster through the inserts. (Round balusters must be a minimum of 32-in. long).

Pre-drill holes: 1/8-in. bit. Attach top bracket flange.

Place top rail brackets over each end of top rail.

Place top rail between post sleeves, fully seated onto balusters.

Remove top rail and mark bracket flange.

Insert all balusters in bottom rail.

A B

11

For horizontal angle applications, use stair bracket mounted on corner of post sleeve as illustrated above.

Above View

Post Sleeve

Rail

Top RailBracket

Top Rail

Stair Bracket

(used for angle)

Deluxe/TraditionalRail Angle Installation:

Place top rail brackets on both ends of top rail.

Seat balusters into top rail. Press down on brackets to snap/lock top rail in place.

To secure the top rail, pre-drill two holes in the flange at the bottom of the bracket with a 1/8-in. bit to the depth of the screw (1-in. for Traditional Rail and 2-in. for Deluxe). Secure the top rail using (2) supplied #10 screws. Do not over tighten.

For installations higher than 30-in. above grade, two additional screws are required to properly secure the top rail: predrill a 1/8-in. hole perpendicular into the flat face of the bracket, approximately 1/2-in. from the post. Drive #10 x 1-in. screw until fully seated. Do not over tighten. Finish by installing screw caps. For Traditional rail, install screws mid-way up the vertical face.

Glue post sleeve cap onto post sleeve.

12

13

14

C

18

19

17

16

15


Place bottom rail brackets onto both ends of bottom rail.

Place bottom rail on top of crush block between post sleeves.

Snap/lock bottom rail in place. Glue crush block to bottom bail.

Insert one baluster into the outermost routed hole at each end.

Remove bottom rail and mark bottom bracket flange holes.

Pre-drill holes: 1/8-in. bit. Attach bottom bracket flange.

4

Lightly trace a line to show the location of the bottom of bracket.

5

6

7

8

10

9


A

A

C

E

B

B

D

Deluxe/Traditional Stair Installation Instructions

Place the square baluster stair Insert or round baluster stair insert into the bottom rail holes, making sure to align them properly. Place square baluster stair Insert or round baluster stair insert into the top rail as well.

Tip: Pinching the insert wings inward makes insertion easier.

Starting from one end and working towards the other and with all balusters in place, lower the top rail and brackets into position, guiding the balusters into the Top Rail Inserts.

Pre-drill the holes for the brackets and secure using the supplied pan head screws.

Finish the installation by gluing on the post sleeve caps and the crush block with a quality exterior adhesive.

Maximum length of rail for even baluster spacing between post sleeves: 6ft Rail: 66 1/4-in.8ft Rail: 90 3/4-in.

NOTE: The slope of the stairs can be 30-36 degrees (an 11-in. run and a 7-in. rise results in a 32 degree slope).

Deluxe Top Stair Bracket

Traditional Top Stair Bracket

Traditional and Deluxe Bottom Stair Bracket

TIP: Insert the brackets over the bottom rails on both ends and mark the angle onto the brackets before cutting. Pre-drill the hole locations, and secure bottom rail with supplied pan head screws.

Establish the angle by laying the bottom rail in front of the secured posts, and marking the angles making sure to center the baluster holes between the posts. Align the top rail with the bottom rail to ensure the baluster holes will align properly before marking the angle for the top rail and brackets.

When using square or turned balusters, the balusters will need to be cut to appropriate length and angle. Transfer the angle using a tool like an adjustable carpenter’s square. It is critical that all balusters are the same length and angle for best appearance.Maximum inside length between

post sleeves:6ft Rail = 56 3/16-in.8ft Rail = 77 1/4-in.

Install 4x4 posts in the pre-determined locations, cover with post sleeve and verify spacing. Posts should be plumb in both directions. If using post sleeve collar, slide collar over post sleeve prior to installing rails.

1 2

B

A

3

4

A

B

5 6

A

B


NOTE: If using the post sleeve collar, make sure to position and glue collars in place prior to securing the bottom rail.

NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing.

NOTE: For best results, cut post sleeves with a 10-in. circular carbide-tipped blade, minimum 32-tooth.

Deluxe/Traditional Stair Installation Instructions

www.fiberonhomeselect.com800.318.7828

Design Grid

DELUXE/TRADITIONAL RAILING INSTALLATION INSTRUCTIONS

Documents

Transcript of DELUXE/TRADITIONAL RAILING INSTALLATION INSTRUCTIONS