DBALL-DBALL2-HYUNDAI2-RSR EN IG NF20170505 · 2017-05-08 · ® Hyundai and Kia are registered...

Rev.: 20170505

Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation

© 2017 Directed. All rights reserved.

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

® Hyundai and Kia are registered trademarks and property of their respective companies.

Important!This product is NOT compatible with vehicles equipped with a manual transmission.

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.

SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.

Installation Guide

Vehicle Application Guide...................................................................................................................................................

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1.................................................................................................................................................................................Type 2.................................................................................................................................................................................Type 3.................................................................................................................................................................................Type 4.................................................................................................................................................................................Type 5.................................................................................................................................................................................Type 6.................................................................................................................................................................................Type 7.................................................................................................................................................................................Type 8.................................................................................................................................................................................Type 9.................................................................................................................................................................................Type 10...............................................................................................................................................................................SmartStart/XL202 Installation Notes..................................................................................................................................

ProgrammingModule Programming.........................................................................................................................................................Module Reset.....................................................................................................................................................................Hard Reset.........................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

LED Diagnostics & Troubleshooting...................................................................................................................................Parking Light Error Codes..................................................................................................................................................

Limited One-Year Consumer Warranty...............................................................................................................................

Quick Reference Guide.....................................................................................................................................................

02

0305070911131517192123

2425262727

2830

31

32

Index

This installation is compatible with firmware 4.05 and up.

The HYUNDAI2 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Hyundai and Kia vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode. This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).

This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on page 24 for more information.

1W

7.5 Amp

Diode 1k

Wire jump template

White conn. M20-R(at steering column)

1 3 52 4 67 9 118 10 12

[1] (-) Horn: White or Gray, pin 6

(-) PTS 1:Yellow/Black,

pin 1

This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n

Vehicle Application Guide

Rev.: 20170505



The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

Vehicles

2017

2016

2015

2014

2013

2012

2011

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

AV

-Panic

Mode

Activ

atio

n

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

RS

-3x

LO

CK

ST

AR

T(S

tart

contr

olu

sin

gO

EM

Rem

ote

)

RS

-3x

LO

CK

ST

OP

(Sto

pcontr

olu

sin

gO

EM

Rem

ote

)

RS

-Rem

ote

Sta

rtR

eady

RS

-Sm

art

Sta

rt

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Hood

Pin

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

SS

-Facto

ryA

larm

Trigger

Monito

ring

ST

-Bra

ke

Sta

tus

(footbra

ke)

Hyundai

Elantra (Smart Key) 2 2 2 1 1 1 • • • • • • • • • • • • • • • • • •

Elantra Coupe (Smart Key) 1 1 • • • • • • • • • • • • • • • • • •

Elantra GT (Smart Key) 2 2 2 2 2 • • • • • • • • • • • • • • • • • •

Veloster (Smart Key) 3 3 3 3 3 • • • • • • • • • • • • • • • • • •

Kia 17 16 15 14 13 12 11

Optima (Smart Key) 5 5 4 4 4 • • • • • • • • • • • • • • • • • •

Optima Hybrid (Smart Key) 5 5 5 4 4 4 • • • • • • • • • • • • • • • • • •

Rio (Smart Key) 10 10 10 10 10 10 • • • • • • • • • • • • • • • • • •

Rondo (Smart Key) 6 6 6 • • • • • • • • • • • • • • • • • •

Sorento (Smart Key) 7 7 • • • • • • • • • • • • • • • • • •

Sportage (Smart Key) 9 9 9 8 8 8 • • • • • • • • • • • • • • • • • •

Legend:

PK: Transponder & Immobilizer Override

AV: Horn & Lights Controls

DL: OE Door Lock & Alarm Controls

RS: Remote Start & Engine Controls

SS: Integrated Security & Monitoring

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



HS CAN Low: Tan: 4

(-) PTS Output 1: Green/Black: 2

FT CAN High: Orange/Green: 5

(-) Parking Lights Output: Red/Black: 4

FT CAN Low: Orange/Brown: 6

(+) Ignition 1 Output: Gray: 6

(+) Ignition 2: Yellow: 8

(+) 12V: Brown: 7

(+) Starter Output: Gray/Black: 7

EMS COM Data: Orange/Black: 11

HS CAN High: Tan/Black: 3

(-) PTS Output 2: Black/White: 1

Hood Pin

Remote Start Safety Override Switch

You can connect to either a XL202 RFTD OR a SmartStart module.

Refer to the SmartStart/XL202 Installation Notes for more information.

6: White/Black: (-) Hood

Note: hood pin only required on vehicles not equipped with a factory hood pin

(+) 12V: Red: 13

(-) Ground: Black: 14

B-CAN High: White/Orange or Brown, pin 13

B-CAN Low: Yellow/Orange or White, pin 1

(-) PTS 1:Yellow/Black, pin 1

Black Conn. M04(at Push-to-Start button)

C-CAN High: White, Pin 6

C-CAN Low: Yellow, Pin 14

1 8

169

OBDIIDiagnostic connector

12

11

22

23

21

20

19

17

16

15

14

131

117

2

19

420

21

6

23

824

9

11

1228

27

13

27

28

31

32

29

36

38

15

18

19

20

34

22

24

25

2

4

7

8

10

11

12

14 1

39 26 13

15

16

31

*

32

*

*

*

*

*

*

*

*

**

*

*

*

*

*

***

**

*

*

*

*

*********

I/P-H (MAIN)I/P-F (MAIN)

I/P-G (MAIN)

23

24

1112

22

10

219

208

197

186

175

164

153

142

131

1 2

87

3

9

4

10

5

11

6

12

(-) Parking Lights:Pink or Orange, pin 2

White conn. M01-L(at Headlight Switch)

1 2 63 74 85 9 10 11 12 13

White conn. I/P-G(Back of I/P Junction Box)

EMS COM Data: Brown/Orange, pin 10

White conn. EM11(Driver Kick Panel)

41

11

26

51

40

50

10

25

1 31

38

39

2 32

3 33

8 23

9

17

18

43

194

205 45

216 46

227 47

27

12

52

28

13

53

29

14

54

30

15

55

34

35

36

37

24

42

48

49

16

44

(+) Starter:Yellow, pin 39

(+) Ignition 1:Pink, pin 27

15

16

17

18

19

20

21

22

23

24

25

28

29

30

31

32

33

34

35

36

37

38

12

23

45

67

89

10

111

13

14

26

27

39

Black conn. I/P-F(Back of I/PJunction Box)

30

86 8587

87a

(+) 12V

Fuse 30A

30

86 8587

87a

(+) 12V

Fuse 30A

Rear of I/P Junction Box (located left side of dash panel)

Installation Type 1

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2

With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

Fuses

I/P Junction Box(Left Side of Dash Panel)

(+) 12V:Red, pin 2

Black Conn. I/P-D(front of I/P Junction Box)

2 31

The Remote Start Safety Override Switch MUST be in the OFF position.

(+) Ignition 2:Orange, pin 1

(-) PTS 2:Yellow/Orange, pin 8

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



Type 1 - Vehicle Wiring Reference Chart

Function Color Pin Polarity Location Color Pins

12V Red 2 (+) I/P-D, front of drivers I/P junction box. Black 3

PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12

PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12

Parking Lights Pink or Orange 2 (-) M01-L, headlight switch. White 13

C-CAN High White 6 Data ODBII. Black 16

C-CAN Low Yellow 14 Data ODBII. Black 16

B-CAN High White/Orange or Brown 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Yellow/Orange or White 1 Data I/P-G, back of drivers I/P junction box. White 24

Ignition 1 Pink 27 (+) I/P-F, back of drivers I/P junction box. Black 39

Ignition 2 Orange 1 (+) I/P-F, back of drivers I/P junction box. Black 39

Starter Yellow 39 (+) I/P-F, back of drivers I/P junction box. Black 39

EMS COM Brown/Orange 10 Data EM11, drivers kick panel. White 55




Parking Lights Pink 2 (-) M01-L, headlight switch. White 13



B-CAN High White/Orange or Brown 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Yellow/Orange or White 1 Data I/P-G, back of drivers I/P junction box. White 24

Ignition 1 Pink 27 (+) I/P-F, back of drivers I/P junction box. Black 39


Starter Yellow 39 (+) I/P-F, back of drivers I/P junction box. Black 39

EMS COM Brown/Orange 10 Data EM11, drivers kick panel. White 55

Wire Information Connector Information

Hyundai Elantra (Smart Key) 2011-2013

Elantra Coupe (Smart Key) 2013-2014

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



B-CAN High: Green, pin 13

B-CAN Low: Orange,pin 1 HS CAN Low: Tan: 4






(+) Ignition 2 Output: Yellow: 8

(+) 12V: Brown: 7







(+) 12V: Red: 13


(+) Starter: Yellow, pin 39

(+) Ignition 1:Pink or White,

pin 27

C-CAN High: White, Pin 6

C-CAN Low: Yellow, Pin 14

1 8

169


12

11

22

23

21

20

19

17

16

15

14

131

117

2

19

420

21

6

23

824

9

11

1228

27

13

27

28

31

32

29

36

38

15

18

19

20

34

22

24

25

2

4

7

8

10

11

12

14 1

39 26 13

15

16

31

*

32

*

*

*

*

*

*

*

*

**

*

*

*

*

*

***

**

*

*

*

*

*********

I/P-H (MAIN)I/P-F (MAIN)

I/P-G (MAIN)

23

24

1112

22

10

219

208

197

186

175

164

153

142

131

(-) Parking Lights: Pink, pin 2

White Conn. M01-L(at Headlight Switch)

1 2 63 74 85 9 10 11 12 13

15

16

17

18

19

20

21

22

23

24

25

28

29

30

31

32

33

34

35

36

37

38

12

23

45

67

89

10

111

13

14

26

27

39

White conn. I/P-G(Back of I/P Junction Box)

Black conn. I/P-F(Back of I/P Junction Box)

EMS COM Data: Brown/Orange, pin 12

39

172

50

49

40

29

28

183

7 22

14

54

44

36

6 21

13

53

43

35

42

34

12

4

205

19

52

11

51

41

33

45

37

1 16

27

38

48

26

32

58

56

57

31

30

47

46

25

24

10

9

238 15

55

White Conn. EM11(Driver Kick Panel) 30

86 8587

87a

(+) 12VFuse 30A

Rear of I/P Junction Box (located left side of dash panel)


Fuses


(+) 12V:Red, pin 2

Black Conn. I/P-D(front of I/P Junction Box)

2 31

Hood Pin





(+) Ignition 2: Orange, pin 130

86 8587

87a

(+) 12VFuse 30A


Black Conn. M04(at Push-to-Start button)

1 2

87

3

9

4

10

5

11

6

12


Installation Type 2

Installation Type 2Page 5

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505











B-CAN High Green 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Orange 1 Data I/P-G, back of drivers I/P junction box. White 24

Ignition 1 Pink or White 27 (+) I/P-F, back of drivers I/P junction box. Black 39


Starter Yellow 39 or 40 (+) I/P-F, back of drivers I/P junction box or EM11, driver kick panel Black or White 39 or 58

EMS COM Blue/Black or Brown/Orange 12 Data EM11, drivers kick panel. White 58







B-CAN High Green 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Orange 1 Data I/P-G, back of drivers I/P junction box. White 24

Ignition 1 Pink or White 27 (+) I/P-F, back of drivers I/P junction box. Black 39


Starter Yellow 39 or 40 (+) I/P-F, back of drivers I/P junction box or EM11, driver kick panel Black or White 39 or 58

EMS COM Blue/Black or Brown/Orange 12 Data EM11, drivers kick panel. White 58


Hyundai Elantra (Smart Key) 2014-2016

Hyundai Elantra GT (Smart Key) 2013-2017

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505




(-) Parking Lights: Red/Black: 4




(-) Autolights Off Output: Blue/Red: 12


Hood Pin






C-CAN High: Red or White, pin 6

C-CAN Low: Blue or Yellow, pin 14

1 8

169



B-CAN High: Red or

White/Orange,pin 5

B-CAN Low:Blue orYellow/Orange,pin 6

White Connector I/P-C(Rear of I/P Junction Box)

24

12

23

1122

10

21

9

20

8

19

7

18

617

516

4

15

3

14

2

13

1

(+) Ignition 1: Pink, pin 7

(+) Starter: Yellow, pin 5

White conn. I/P-F(front of I/P Junction Box)

43 10

13 16

2 9

12 15

1 8

11 145 6 7

(-) PTS 1: Yellow/Black, pin 1

White conn. M04(at Push-to-Start button)

1 3 52 4 6

7 9 118 10 12

White conn. MF11(Driver Kick Panel)

(-) Driver Door Trigger:Brown, pin 7

For Veloster2012-2013

& early 2014

For Velosterlate 2014-2016OR

EMS COM EMS COM

White conn. EM11(Driver Kick Panel)

Black conn. EM11(Driver Kick Panel)

EMS COM Data: Blue, pin 10

41

11 51

40

10

25

1 31

38

39

28

9

17

18

19

20

21

22

27

28

29

30

34

35

36

37

24

42

48

49

16

44

HS CAN Low: Tan: 4





(+) 12V: Red: 13


(+) 12V: Brown: 7

I/P-K

I/P-G

I/P-H

Fu

ses

I/P-L

I/P-E I/P-F

I/P-M

I/P-N

Fuse Panel (front)

I/P Junction Box(left side of Dash Panel)

30

86 8587

87a

(+) 12VFuse 30A

Installation Type 3

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


1 2 3 4

(+) 12V:Red, pin 2

Black Conn. I/P-L(front of I/P Junction Box)


(+) Ignition 2: Red, pin 4

30

86 8587

87a

(+) 12VFuse 30A

(-) PTS 2: Yellow/Orange, pin 8

1 29

48

10

37

19

27

28

55

2 20

34

57

89

6

13

12

16

15

14

17

18

21

39

48

22 32

31

40

49

23

33

41

50

24

34

43

52

42

51

25

35

44

53

26

36

45

54

30

11 38

47

56

EMS COM Data: Blue, pin 16

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505




Function Color P in Pola rity Loca tion Color P ins

12V Red 2 (+) I/P-L, front of drivers I/P junc tion box. W hite 4


PTS 2 Yellow/O range 8 (-) M04, Push-to-Start Button. Black 12

C-CAN High W hite 6 Data O DBII. Black 16

C-CAN Low Yellow 14 Data O DBII. Black 16

Ignition 1 Pink 7 (+) I/P-F, front of drivers I/P junc tion box. W hite 16

Ignition 2 Red 4 (+) I/P-F, front of drivers I/P junc tion box. W hite 16

Starter Yellow 5 (+) I/P-F, front of drivers I/P junc tion box. W hite 16

B-CAN High W hite/O range 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24

B-CAN Low Yellow/O range 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24

Parking Lights Pink 11 (-) I/P-C, back of drivers I/P junc tion box. W hite 24

EMS CO M Blue 10 Data EM11, drivers kick panel. W hite 55

Drivers Door Trigger Brown 7 (-) MF11, drivers kick panel. W hite 56












EMS CO M Blue 16 Data EM11, drivers kick panel. W hite 55














EMS CO M Blue 16 Data EM11, drivers kick panel. Black 60

12V Red 1 (+) I/P-C, front of drivers I/P junc tion box. Black 4



C-CAN High Red 6 Data O DBII. Black 16

C-CAN Low Blue 14 Data O DBII. Black 16




B-CAN High Red 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24

B-CAN Low Blue 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24



EMS CO M Blue 16 Data EM11, drivers kick panel. Black 60

Hyundai Ve loste r (Smart Key) 2016

W ire Inform a tion Conne ctor Inform a tion

Hyundai Ve loste r (Smart Key) 2012-2013

Hyundai Ve loste r (Smart Key) 2014 (Early)

Hyundai Ve loste r (Smart Key) 2014 (Late ) - 2015

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



Hood Pin












C-CAN High: White, pin 6

C-CAN Low: Yellow, pin 14

1 8

169




21 63 74 85 9 10 11 12 13

110

19

28

36

40

211

20

29

37

41

312

21

30

38

42

413

22

31

39

43

514

23

32

615

24

33

716

25

34

8918

27

17

26

35

White Conn. EM11(Driver Kick Panel)

EMS COM Data:Brown/Orange or Blue, pin 10

B-CAN Low:Yellow/Orange, pin 38

B-CAN High:White/Orange, pin 25

(+) Starter:Orangeor Yellow,pin 26

15

16

17

18

19

20

21

22

23

24

25

28

29

30

31

32

33

34

35

36

37

38

12

23

45

67

89

10

111

13

14

26

27

39


Black conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)

HS CAN Low: Tan: 4





(+) 12V: Red: 13


(+) 12V: Brown: 7

30

86 8587

87a

Fuse 30A

Installation Type 4

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


Fuses


(+) 12V:Red or Pink, pin 1

Black Conn. I/P-C(front of I/P Junction Box)

2 31


(+) Ignition 2:

Orange, pin 14

30

86 8587

87a

(+) 12V

Fuse 30A


Black conn. M04(at Push-to-Start button)

1 2

87

3

9

4

10

5

11

6

12


1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505





12V Pink 1 (+) I/P-C, front of drivers I/P junction box. Black 3






B-CAN High White/Orange 25 Data I/P-E, back of drivers I/P junction box. Black 39

B-CAN Low Yellow/Orange 38 Data I/P-E, back of drivers I/P junction box. Black 39

Ignition 1 Pink 1 (+) I/P-E, back of drivers I/P junction box. Black 39

Ignition 2 Orange 14 (+) I/P-E, back of drivers I/P junction box. Black 39

Starter Orange or Yellow 26 (+) I/P-E, back of drivers I/P junction box. Black 39

EMS COM Brown/Yellow 10 Data EM11, drivers kick panel. White 43

12V Red 1 (+) I/P-C, front of drivers I/P junction box. Black 3






B-CAN High White/Orange 25 Data I/P-E, back of drivers I/P junction box. Black 39

B-CAN Low Yellow/Orange 38 Data I/P-E, back of drivers I/P junction box. Black 39

Ignition 1 Pink 1 (+) I/P-E, back of drivers I/P junction box. Black 39

Ignition 2 Orange 14 (+) I/P-E, back of drivers I/P junction box. Black 39

Starter Yellow 26 (+) I/P-E, back of drivers I/P junction box. Black 39

EMS COM Blue 10 Data EM11, drivers kick panel. White 43


Kia Optima (Smart Key) 2011-2013

Kia Optima Hybrid (Smart Key) 2011-2013

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505











White conn. I/P-G(Back of I/P Junction Box,

located left side of dash panel)


White conn. M 01-L(at Headlight Switch)

21 63 74 85 9 10 11 12 13

B-CAN High: White/Orange, pin 13

B-CAN Low: Yellow/Orange, pin 1

1

13

2

14

3

15

4

16

5

17

6

18

7

19

8

20

9

21

10

22

11

23

12

24

C-CAN High: White, pin 6

C-CAN Low: Yellow, pin 14

1 8

169

OBDIIDiagnosticconnector

(+) Starter: Yellow or Gray, pin 9

(+) Ignition 2: Orange, pin 32

EMS COM Data: Brown/Orange or Blue, pin 41


HS CAN Low: Tan: 4





(+) 12V: Red: 13


(+) 12V: Brown: 7

30

86 8587

87a

Fuse30A

(+) 12V

30

86 8587

87a

Fuse30A

(+) 12V

Installation Type 5

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


Fuses


(+) 12V:Red, pin 1

Black Conn. I/P-C(front of I/P Junction Box)

2 31

Hood Pin






pin 1


1 2

87

3

9

4

10

5

11

6

12


(+) Ignition 1: Pink, pin 26

5

39

172

50

49

40

29

28

183

7 22

21

14

54

44

36

6 13

53

43

35

42

34

12

4

20

19

52

11

51

41

33

45

37

1 16

27

38

48

26

32

58

56

57

31

30

47

46

25

24

10

9

238 15

55

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505











B-CAN High White/Orange 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Yellow/Orange 1 Data I/P-G, back of drivers I/P junction box. White 24

Ignition 1 Pink 26 (+) EM11, drivers kick panel. White 58

Ignition 2 Orange 32 (+) EM11, drivers kick panel. White 58

Starter Gray 9 (+) EM11, drivers kick panel. White 58

EMS COM Brown/Orange or Blue 41 Data EM11, drivers kick panel. White 58







B-CAN High White/Orange 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Yellow/Orange 1 Data I/P-G, back of drivers I/P junction box. White 24


Ignition 2 Black/Orange 32 (+) EM11, drivers kick panel. White 58

Starter Gray 9 (+) EM11, drivers kick panel. White 58



Kia Optima (Smart Key) 2014-2015

Kia Optima Hybrid (Smart Key) 2014-2016

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505











1 8

169

OBDIIDiagnosticconnector C-CAN High: White, pin 6

C-CAN Low: Brown, pin 14

B-CAN High: Orange, pin 13

B-CAN Low:Blue, pin 1

White Conn. I/P-G(Back of I/P Junction Box,


24

12

23

11

22

10

21

9

20

8

19

7

18

6

17

5

16

4

15

3

14

2

13

1

EMS COM Data:Blue/Orange, pin 37


(+) Ignition 2:White, pin 32

(+) Starter: Green, pin 49

39

172

50

49

40

29

28

183

7 22

14

54

44

36

6 21

13

53

43

35

42

34

12

4

205

19

52

11

51

41

33

45

37

1 16

27

38

48

26

32

58

56

57

31

30

47

46

25

24

10

9

238 15

55



White Conn. M01-L(at Headlight Switch)

8

16

7

15

6

145

13

4

12

3

11

2

10

1

9

HS CAN Low: Tan: 4





(+) 12V: Red: 13


(+) 12V: Brown: 7

30

30

86

86

85

85

87

87

87a

87a

Fuse30A

Fuse30A

(+) 12V

(+) 12V

Installation Type 6

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


Fuses


(+) 12V:Green,pin 1

2 31

Black conn.(front of I/P

Junction Box)

Hood Pin






pin 1


1 2

87

3

9

4

10

5

11

6

12


1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505





12V Green 1 (+) I/P-C, front of drivers I/P junction box. Black 3





C-CAN Low Brown 14 Data ODBII. Black 16

B-CAN High Orange 13 Data I/P-G, back of drivers I/P junction box. White 24

B-CAN Low Blue 1 Data I/P-G, back of drivers I/P junction box. White 24


Ignition 2 Orange 32 (+) EM11, drivers kick panel. White 58

Starter Green 49 (+) EM11, drivers kick panel. White 58



Kia Rondo (Smart Key) 2014-20161W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505










1 8

169


C-CAN High:White, pin 6

C-CAN Low: Red, pin 14

White or Black conn. EM11(Driver Kick Panel)

29

38

19

28

110

30

37

20

27

1118

29

31

32

33

34

35

36

12

13

14

15

16

17

21

22

23

24

25

26

34

56

78

(-) Parking Lights: Blue, pin 2


1 2 63 74 85 9 10 11 12 13

EMS COM Data:Blue/Orange, pin 15

White conn. I/P-M(Back of I/P Junction Box,


White conn. I/P-C(Front of I/P Junction Box,located left side of dash panel)

B-CAN High:Black, pin 5

B-CAN Low:White, pin 6

(+) Ignition 1: Red, pin 28

(+) Ignition 2:White, pin 38

(+) Starter: Green, pin 37

8

16

7

15

6

14

5

13

4

12

3

11

2

10

1

9

46

36

26

21

111

29

22

24

34 14 29

39

5 15 30

40

6

17

31

41

7

16

32

42

8 18 33

43

10

23

25

12

12

27

34

37

44

13

13

28

35

38

45


2615 16 17 18 19 20 21 22 23 24

4 5 6 7 8 9 10 11 132 3

2514

121

(-) Driver Door Trigger:Red/Black, pin 6

White conn. I/P-K(Front of I/P Junction Box,



HS CAN Low: Tan: 4





(+) 12V: Red: 13

(-) Ground: Black: 14(-) Ground

(+) 12V: Brown: 7

30

86 8587

87a

(+) 12V

30

86 8587

87a

(+) 12V

Fuse 30A

Fuse 30A

Installation Type 7

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


Hood Pin





3536

27

8 7 6 5 4 3 2 1

9101112

1920212223242526

1314151617

18

28293031323334

(+) 12V:Red, pin 1

White conn. I/P-B(Front of I/P Junction Box, left side of dash panel)


pin 1


1 2

87

3

9

4

10

5

11

6

12

(-) PTS 1:Yellow/Orange,pin 8

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505





PTS 1 Brown/Black 1 (-) M57, Push-to-Start Button. Black 12

PTS 2 Pink/Black 8 (-) M57, Push-to-Start Button. Black 12

Parking Lights Blue 2 (-) M14-L, headlight switch. White 13


C-CAN Low Red 14 Data ODBII. Black 16

B-CAN High Black 5 Data I/P-M, back of drivers I/P junction box. White 16

B-CAN Low White 6 Data I/P-M, back of drivers I/P junction box. White 16

Driver Door Trigger Red/Black 6 (-) I/P-K, back of drivers I/P junction box. White 26

12V Red 1 (+) I/P-B, front of drivers I/P junction box. White 36

Ignition 1 Red 28 (+) I/P-E, back of drivers I/P junction box. White 38

Ignition 2 White 38 (+) I/P-E, back of drivers I/P junction box. White 38

Starter Green 37 (+) I/P-C, back of drivers I/P junction box. White 38


Kia Sorento (Smart Key) 2014-20151W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



HS CAN Low: Tan: 4

(-) PTS 1 Output : Green/Black: 2








(-) PTS 2 Output: Black/White: 1



(+) 12V: Red: 13


(+) Starter: Red, pin 1

FT CAN Low: Red, pin 52 FT CAN High:Blue, pin 53

(+) Ignition 1: Blue, pin 25

(+) Ignition 2Blue or White,

pin 31

1 8

169


HS CAN High:Green, pin 6

HS CAN Low:Orange, pin 14

White conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)

31 54

25 30

1 242334

34

8

38

13

43

17

47

5

35

9

39

14

44

18

48

6

36

10

40

15

45

19

49

7

37

11

41

12

42

16

46

20

50

21

51

2928

5333

222

2827

5232




6 74 85 9 10 11 12 1321 3

(+) 12V: Brown: 7

30

30

86

86

85

85

87

87

87a

87a

(+) 12V

(+) 12V

Fuse 30A

Fuse 30A

EMS COM Data:Blue, pin 7

Yellow conn. MC11(Passenger Kick Panel)

24 18

12 6

23 17

11 5

22 16

10 4

21 15

9 3

20 14

8 2

19 13

7 1

Installation Type 8

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


Fuses


(+) 12V:Red, pin 1

Black Conn. I/P-A(front of I/P Junction Box)

2 31

Hood Pin





10

5

9

4

83

72

61

(-) PTS 2:White,

pin 7

(-) PTS 1:White/Black,pin 8


1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505





12V Red 1 (+) I/P-A, front of drivers I/P junction box. Black 3

PTS 1 White/Black 7 (-) M04, Push-to-Start Button. Black 10

PTS 2 White 1 (-) M04, Push-to-Start Button. Black 10


C-CAN High Green 6 Data ODBII. Black 16

C-CAN Low Orange 14 Data ODBII. Black 16

EMS COM Blue 7 Data MC11, passenger kick panel. Yellow 24

B-CAN High Blue 53 Data I/P-E, back of drivers I/P junction box. White 54

B-CAN Low Red 52 Data I/P-E, back of drivers I/P junction box. White 54

Ignition 1 Blue 31 (+) I/P-E, back of drivers I/P junction box. White 54


Starter Red 7 (+) I/P-E, back of drivers I/P junction box. White 54


Kia Sportage (Smart Key) 2011-20131W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



HS CAN Low: Tan: 4

(-) PTS 1 Output: Green/Black: 2








(-) PTS 2 Output: Black/White: 1



(+) 12V: Red: 13


(+) Starter: Red, pin 1

FT CAN Low: Red, pin 52 FT CAN High:Blue, pin 53

(+) Ignition 1: Blue, pin 25

(+) Ignition 2Blue or White,

pin 31

1 8

169


HS CAN High:Green, pin 6

HS CAN Low:Orange, pin 14

White conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)

31 54

25 30

1 242334

34

8

38

13

43

17

47

5

35

9

39

14

44

18

48

6

36

10

40

15

45

19

49

7

37

11

41

12

42

16

46

20

50

21

51

2928

5333

222

2827

5232




6 74 85 9 10 11 12 1321 3

(+) 12V: Brown: 7

30

30

86

86

85

85

87

87

87a

87a

(+) 12V

(+) 12V

Fuse 30A

Fuse 30A

EMS COM Data:Blue, pin 7

Yellow conn. MC11(Passenger Kick Panel)

24 18

12 6

23 17

11 5

22 16

10 4

21 15

9 3

20 14

8 2

19 13

7 1

Installation Type 9

10

RF

Programming button

LED

4

12

14

2

10

DBALL/DBALL2


Fuses


(+) 12V:Red, pin 1

Black Conn. I/P-A(front of I/P Junction Box)

2 31

Hood Pin






1 2

87

3

9

4

10

5

11

6

12

(-) PTS 2:White,

pin 1

(-) PTS 1:White/Black,pin 8

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505





12V Red 1 (+) I/P-A, front of drivers I/P junction box. Black 3

PTS 1 White/Black 8 (-) M04, Push-to-Start Button. Black 12

PTS 2 White 1 (-) M04, Push-to-Start Button. Black 12


C-CAN High Green 6 Data ODBII. Black 16

C-CAN Low Orange 14 Data ODBII. Black 16

EMS COM Blue 7 Data MC11, passenger kick panel. Yellow 24

B-CAN High Blue 53 Data I/P-E, back of drivers I/P junction box. White 54

B-CAN Low Red 52 Data I/P-E, back of drivers I/P junction box. White 54



Starter Red 7 (+) I/P-E, back of drivers I/P junction box. White 54


Kia Sportage (Smart Key) 2014-20161W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



HS CAN Low: Tan: 4





(+) 12V: Brown: 7

(+) Ignition 2: Yellow: 8







(+) 12V: Red: 13


Blue or Black conn. JM02(Left side of I/P Junction Box,


1 8

169


C-CAN High: Red, pin 6

C-CAN Low: Blue, pin 14

B-CAN High: Brown, pin 9

(+) 12V: Red, pin 1

B-CAN Low: White, pin 19

(-) Parking Lights:Pink/Black, pin 2


1 2 63 74 85 9 10 11 12 13

(+) Starter:Red or White,pin 3

1

11

2

12

3

13

4

14

5

15

6

16

7

17

8

18

9

19

10

20

15

6313 14 16

74

17

85

18

9

19

10

20

11

1

21

12

2

Black conn. I/P-D(Front of I/P JunctionBox, located on leftside of dash panel)


White conn. MF31 (Driver Kick Panel)

(-) Driver Door Trigger: Green, pin 2


35

15

25 5

37

17

27 7

38

18

28 8

34

14

24 4

310

1141

131

13

20

23

30

33

40

29

12

19

22

29

32

39

36

16

26 21 6

EMS COM Data:Blue/Black, pin 36

White conn. EM 11(right side of I/P Junction Box,


(+) Ignition 1: Green, pin 25

White conn. I/P-B(Back of I/P Junction Box,


31

54

25

30

124

23

34 34

8 38

13

43

17

47

5 35

9 39

14

44

18

48

6 36

10

40

15

45

19

49

7 37

11 41

12

42

16

46

20

50

21

51

29

28

53

33

22

2

28

27

52

32

30

86 8587

87a

Fuse30A

(+) 12V

White conn. I/P-A(Back of I/P Junction Box,


Installation Type 10

10

RF

Prog. Button

LED

4

12

14

2

10

DBALL/DBALL2


1

2

Hood Pin





(+) Ignition 2: Green, pin 31

30

86 8587

87a

(-) PTS 1: Pink

Smart Key Module Harness(back of fusebox)

(-) PTS 2: Gray/Black

Fuse30A

(+) 12V

111 212 3

17

4

30

18

5

31

19

6

32

20

7

33

21

8

34

22

9

35

23

10

36

13

1424 1525 1626

2737 2838 2939

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505






Parking Lights Pink/Black 2 (-) M02-L, headlight switch White 13

C-CAN High Red 6 Data ODBII. Black 16

C-CAN Low Blue 14 Data ODBII. Black 16

B-CAN High Brown 9 Data JM02, left side of drivers I/P junction box. Blue or Black 20

B-CAN Low White 19 Data JM02, left side of drivers I/P junction box. Blue or Black 20

Starter White or Red 3 (+) I/P-A, back of drivers I/P junction box. White 21

EMS COM Blue/Black 36 Data EM11, right side of drivers I/P junction box. White 41

Drivers Door Trigger Green 2 (-) MF31, driver kick panel. White 39

Ignition 1 Green 25 (+) I/P-B, back of drivers I/P junction box. White 54

Ignition 2 Red 1 (+) I/P-B, back of drivers I/P junction box. White 54

PTS 1 Pink N/A (-) Smart Key Module harness, back of fusebox. N/A N/A

PTS 2 Gray/Black N/A (-) Smart Key Module harness, back of fusebox. N/A N/A


Kia Rio (Smart Key) 2012-20161W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



SmartStart/XL202 Installation Notes

The optional XL202 and antenna are not included and MUST be purchased separately.

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

4

4

XL202

An

ten

na

XOVER

SmartStart is optional and not included. It MUST be purchased separately.

SmartStart is optional and not included. It MUST be purchased separately.

The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system; 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.

Configuration Wires (Gray & White)Connect Gray wire to (-) Ground

5 pins

D2D (4 pins, white)

4 pins

2 pins, not usedCABLE

CABLE

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

SmartStart Revision B

RF Kit

RF Kit & PKE Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

RF Kit, PKE & SmartStart BT Combination

SmartStart Revision A

DBALL/DBALL2

DBALL/DBALL2

DBALL/DBALL2

LED

Prog.Button

D2D (4 pins, white)

4 pins

2 pins, not used

OR

SmartStart

Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop

LED

THIS SIDE UP

LED

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Module Programming

Rev.: 20170505



ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.

Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.

1. Connect the interface module to your computer using the XKLoader.

2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.

3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.

4. In the search result page, select Config for RSR, and follow the instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:

“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.

1

2

10-pinD2D

st1

12-pin14-pin

nd2

rd3

&Solid

Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.

10-pinD2D

XL202

10-pinD2DSmartStart

OR

The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.

a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).

b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.

Connect SmartStart to DBALL using the D2D port.

SmartStart Installation

Connect XL202 to DBALL using the D2D port.

XL202 Installation

Go to the next page to complete the module programming.

Refer to the LED Diagnostics section on pages 28-29 for more information and for troubleshooting purposes.

Key Inside the Vehicle

HOLDMake sure the key is inside the vehicle.

3Turn the ignition knob to RUN position.

For Vehicles with Knob

Press the Push-to-Start (PTS) button twice to turn the ignition ON.

For Vehicles with PTS

Important: Do NOT press the brake pedal.Important:

2XENGINESTARTSTOP

PUSHDo NOTpress the brake pedal

Turn Knob

Key to Run

RU N C C A S T A RF

TF O

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



The LED flashes orange for few seconds to indicate the module is in learningmode then the LED turns ON solid green for 3 seconds and shuts off.The module is now programmed.

4 &&OffFlashes

Orange

Solid

x3 secs

Turn the ignition knob to the OFF position.

51X

ENGINESTARTSTOP

PUSH

Press the Push-to-Start (PTS) button once more to turn the ignition OFF.

Turn Knob

Key to Run

RU N C C A S T A RF

TF O

For Vehicles with Knob For Vehicles with PTS

You have successfully completed the module programming sequence.

Module Reset

2 & &Solid SolidRelease

Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-pin

nd2

rd3

th4

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.

Release the programming button. The LED turns ON solid red.

Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-pin

nd2

rd3

th4

Hard Reset

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



Feat. Operation Flashes / Option Description

1. No RF Output* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver priority*Unlocks only the driver door on first press and unlocks all doors on a second press within 5

seconds.

2. All Unlocks all doors on first press.

1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will

be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.

2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will

unlock at the beginning of the sequence, and relock after start and shutdown.

3. Enabled*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the

vehicle in the remote start sequence, only when required. The reason for this is, factory alarm

control must often be done by lock or unlock operation. This could create unnecessary actions on

door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will

monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is

unlocked or is not equipped with factory alarm, the

disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter

actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock

feature is active, will work perfectly with this option and will make it invisible to the user.*Default

Unlock Driver Priority

Smart OEM Alarm

Control

1 RFTD Output Type

2

3

Feature & Option List

It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, a manual configuration of the features is possible using the information on this page.

To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the

Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate

the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.

Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the

DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.

- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to

indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming

sequence.OR

- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.

Feature Programming Programming Button

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


LED Diagnostics & Troubleshooting

Rev.: 20170505



LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



Flashes Diagnostic

1 Runtime expired.

2 Over-rev shutdown.

3 Low/No RPM.

4 Transmitter shutdown.

5 Brake shutdown.

6 Hood shutdown/Remote start safety override switch is ON*.

7 Remote start safety override switch is ON*.

The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.

* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.

Parking Light Error Codes

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Rev.: 20170505



Limited One Year Consumer Warranty

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

1W

7.5 Amp

Diode 1k

Wire jump template


1 3 52 4 67 9 118 10 12



pin 1


Quick Reference GuideDBALL/DBALL2-HYUNDAI2 Remote Start Ready (RSR) Installation


1

2

3

Stop the vehicle in a safe parking spot and put the gear in Park (P).

Press remote start

button*

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

Flashes

ENGINESTARTSTOP&

HOLD

Exit vehicle with Smart Key

Pit Stop Mode

The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.

Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.

It is now safe to leave the engine running and exit the vehicle with the factory remote in hand.

Press the button to remote start the vehicle.*

The PTS button will flash once to indicate the vehicle is now in Pit Stop Mode.

Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.

Flashes Diagnostic

1 Runtime expired.

2 Over-rev shutdown.

3 Low/No RPM.

4 Transmitter shutdown.

5 Brake shutdown.

6 Hood shutdown/Remote start safety override switch is ON*.

7 Remote start safety override switch is ON*.

* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.

Vehicle Takeover

HOLD

5

3

1Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.*

2

Depress the brake pedal, put the carin gear and drive off.

Enter the vehicle, while making sure the factory remote is inside with you.

Press the Unlock button on the factory or aftermarket remote.*

Ready to drive off

Press remote start

button**

Press Unlock button on

either remote**HOLD OR

Enter vehicle with key fob

* Your aftermarket remote may differ from the model shown in the illustrations.

Complete the following steps within 45 secondsor the vehicle will shut down.

4 Press twice on the PTS switch.

�佒L �� A�

佃呅剆

G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭

块偐佒

W��T��单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣��

Hyundai Genesis Sedan with Smart Key

©2010DirectedElectronics.Allrightsreserved.

("Push-button Start")

Hyundai proximity key solution

Quick Reference GuideDBALL/DBALL2-HYUNDAI2 Remote Start Ready (RSR) Installation


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Remote Start Ready (RSR)

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.

SmartStart Compatible

This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart?

Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:

Ÿ Lock/ArmŸ Unlock/DisarmŸ Remote Car StarterŸ Trunk ReleaseŸ PanicŸ Aux Channels

You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!

But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.

3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

For more information, visit www.mysmartstart.com.

3x OEM Lock Remote Start Activation

This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.

Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.

�佒L �� A�

佃呅剆

G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭

块偐佒

W��T��单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣��

Hyundai Genesis Sedan with Smart Key

©2010DirectedElectronics.Allrightsreserved.

("Push-button Start")

Hyundai proximity key solution

DBALL-DBALL2-HYUNDAI2-RSR EN IG NF20170505 · 2017-05-08 · ® Hyundai and Kia are registered...

Documents

Transcript of DBALL-DBALL2-HYUNDAI2-RSR EN IG NF20170505 · 2017-05-08 · ® Hyundai and Kia are registered...