DBALL-DBALL2-GM10-RSR EN IG TH20150118 · Type 1c - THGM610 Rev. 2 (With T-Harness) Page 5 [1] If...

Index

® Buick, Chevrolet and GMC are registered trademarks and property of their respective companies.

Vehicle Application Guide.....................................................................................................................................................................

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1a (Without T-Harness)...............................................................................................................................................................Type 1b (With T-Harness - Rev. 1).......................................................................................................................................................Type 1c (With T-Harness - Rev. 2)......................................................................................................................................................Vehicle Wiring Reference Chart - Type 1.............................................................................................................................................Type 2a (Without T-Harness)...............................................................................................................................................................Type 2b (With T-Harness - Rev. 1).......................................................................................................................................................Type 2c (With T-Harness - Rev. 2).......................................................................................................................................................Vehicle Wiring Reference Chart - Type 2.............................................................................................................................................Type 3..................................................................................................................................................................................................Vehicle Wiring Reference Chart - Type 3.............................................................................................................................................SmartStart/XL202 Installation Notes....................................................................................................................................................

ProgrammingModule Programming...........................................................................................................................................................................Module Reset.......................................................................................................................................................................................Hard Reset...........................................................................................................................................................................................Feature & Option List...........................................................................................................................................................................Feature Programming..........................................................................................................................................................................

LED Diagnostics & Troubleshooting....................................................................................................................................................

Limited One-Year Consumer Warranty.................................................................................................................................................

Quick Reference Guide........................................................................................................................................................................

02

0304050609101112141516

1718181920

21

23

24

Installation Guide

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a Plug & Play THGM610 T-Harness (optional). This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart (all sold separately). Refer to section for SmartStart and XL202 installation.

Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how to use the various features offered with this product.

Using this product without RF Kit is not recommended since the factory remote is disabled during run time.

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.

Important:

This guide is compatible with the GM10 firmware version 3.18 and later.

This product is NOT compatible with vehicles equipped with a manual transmission.

SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.

Rev.: 20160118

Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation v. 3.18+

© 2016 Directed. All rights reserved.

Vehicle Application Guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

Vehicles

2016

2015

2014

2013

2012

2011

2010

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

CC

-Heate

dS

eats

Activ

atio

n

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

RS

-3x

LO

CK

ST

AR

T(S

tart

contr

ol

usin

gO

EM

Rem

ote

)

RS

-3x

LO

CK

ST

OP

(Sto

pcontr

ol

usin

gO

EM

Rem

ote

)

RS

-RA

PS

hutD

ow

n(R

eta

ined

AC

C

Pow

er)

RS

-Rem

ote

Sta

rtR

eady

RS

-Sm

art

Sta

rt

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Driver

Door

Pin

SS

-Entr

yM

onito

ring

Hood

Pin

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

ST

-Bra

ke

Sta

tus

(footbra

ke)

Buick

Encore 1 1 1 • • • • • • • • • • • • • • • •

LaCrosse 1 1 1 1 1 • • • • • • • • • • • • • • • •

Regal 1 1 1 1 1 • • • • • • • • • • • • • • • •

Verano 1 1 1 1 • • • • • • • • • • • • • • • •

Chevrolet

Camaro 1 1 1 1 • • • • • • • • • • • • • • • • •

Camaro 1 1 • • • • • • • • • • • • • • • •

Colorado 2 • • • • • • • • • • • • • • •

Cruze 1 1 1 1 1 • • • • • • • • • • • • • • • •

Equinox 1 1 1 1 • • • • • • • • • • • • • • • • •

Equinox 1 1 • • • • • • • • • • • • • • • •

Impala 1 1 • • • • • • • • • • • • • • • •

Malibu 1 1 1 • • • • • • • • • • • • • • • •

Orlando 1 1 • • • • • • • • • • • • • • • •

Silverado 1500 [2] 2 2 • • • • • • • • • • • • • • • •

Silverado 2500/3500 [2] 2 • • • • • • • • • • • • • • • •

Sonic 1 1 1 1 • • • • • • • • • • • • • • • •

Spark [1] 3 3 • • • • • • • • • • • • • • • •

Suburban 2 • • • • • • • • • • • • • • • • •

Tahoe 2 • • • • • • • • • • • • • • • • •

Trax 1 1 1 1 • • • • • • • • • • • • • • • •

GMC

Canyon 2 • • • • • • • • • • • • • • •

Sierra 1500 [2] 2 2 • • • • • • • • • • • • • • • •

Sierra 2500/3500 [2] 2 • • • • • • • • • • • • • • • •

Terrain 1 1 1 1 1 1 • • • • • • • • • • • • • • • •

Yukon 2 • • • • • • • • • • • • • • • • •

Legend:

CC: Comfort & Convenience Controls RS: Remote Start & Engine Controls

DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring

FOB: Sync CAN Interface w/FOB Remote ST: Function/Feature Status

PK: Transponder & Immobilizer Override

Rev.: 20160118



Type 1a (Without T-Harness)

Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect this wire (Green/Black, pin 2/12) to the driver door sense trigger to avoid the issue.

With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

SW Can: Green, pin 1

CAN High: Tan/Black or Blue, pin 6

Ground: Black, pin 4

CAN Low: Tan or White,

pin 14

(+) 12V: pin 16

OBDIIDiagnostic Connector

321

Immobilizer Control Module (under ignition switch,

black connector)

Cut

TX

(-) Ground

RX

(+)12V

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12

2(-) Driver Door Sense Trigger [1]

1 8

169

6: White/Black: (-) Hood

Hood Pin

Remote Start Safety Override Switch

Note: Hood pin only required on vehicles not equipped with a factory hood pin.

You can connect to either a XL202 RFTD OR a SmartStart module.

Refer to the SmartStart/XL202 Installation Notes for more information.

Single Wire CAN: Light Green: 1

(+) Ignition Output: Yellow: 8

(+) 12V: Brown: 7

Immo. Data (veh. side): Yellow/Red: 11

Immo. Data: Brown/Red: 12

(+) 12V: Red: 13

(-) Ground: Black: 14

Immo. Data (conn. side): Orange/Red: 10

[1] (-) RAP Off: Green/Black: 2

(-) Parking Lights Output: Black/White: 1

Immo. Data (veh. side): Orange/Black: 11

Immo. Data: Yellow/Black: 10

(+) Accessory Output: Gray/Black: 7

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

654321

(+) Ignition: pin 1

(+) Accessory: pin 3

Light Switch Connector

1 2 3 4 5

7

6

121198 10

Refer to the Vehicle Wiring Reference Charts (pages 10 to 15) for wire color and location.

(-) Parking Lights: pin 3

Ignition Switch

Immo.Data: pin 2

Rev.: 20160118



Type 1b - THGM610 Rev. 1 (With T-Harness)

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+) 12V

To vehicle 6-pin connector

Ignition Connector

Use connectors labeled GM10

[1] (-) RAP Off: Green/Black

(-) Parking Lights Output: Black/White

(-) Driver Door Sense

Trigger [1]

n/a: Violet/Green

n/a: Violet/Brown

n/a:Pink


Hood Pin

Note: hood pin only required on vehicles not equipped with a factory hood pin

Wh

ite/B

lack

T-HarnessTHGM610(Optional)

Ignition Barrel

Cut away the 4-pin connector and connect

the three wires to the OBDII 16-pin connector.

Diagnostic ConnectorOBDII (connector side view)1 8

169


Tan

/Bla

ck

CAN Low: Tan or White, pin 14

Tan

SW CAN: Green, pin 1

Lt. G

reen

To Immobilizer

Control Module (ICM)(vehicle side)

GM10 GM10

T-01

GM06

NOT USED





To Immobilizer Control Module (ICM)(under ignition switch,black connector)

Light Switch

Connector1 2 3 4 5

7

6

121198 10

T-02

OR

NOT USED



T-01

Buick Encore

Buick LaCrosse

Buick Regal

Buick Verano

Chevrolet Camaro

Chevrolet Cruze

Chevrolet Equinox

Chevrolet Impala

Chevrolet Malibu

Chevrolet Orlando

Chevrolet Sonic

Chevrolet Trax

GMC Terrain

Rev.: 20160118



Type 1c - THGM610 Rev. 2 (With T-Harness)



Ignition Barrel

XKD2D65

(-) Parking Lights Output:Black/White

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+) 12V



Ignition Connector


NOT USED


Trigger [1]

n/a: Pink


GM10

GM06

GM10

T-01

Use connectors labeled GM10.

To Immobilizer Control Module (ICM)(vehicle side)

[1] RAP Off Green/Black

Diagnostic ConnectorOBDII (connector side view)

1 8

169


CAN Low: Tan or White, pin 14


Lt.G

ree

n

Tan

Tan

/Bla

ck

T-02NOT USED


1 2 3 4 5

7

6

121198 10


T-01

Buick Encore

Buick LaCrosse

Buick Regal

Buick Verano

Chevrolet Camaro

Chevrolet Cruze

Chevrolet Equinox

Chevrolet Impala

Chevrolet Malibu

Chevrolet Orlando

Chevrolet Sonic

Chevrolet Trax

GMC Terrain


Hood Pin


Wh

ite/B

lack

Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.

Rev.: 20160118



Rev.: 20160118



Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.

Vehicle Wiring Reference Chart - Type 1

Function Color Pin Polarity Location Color Pins

Ignition Violet/ Black 1 (+) Ignition Control Switch Black 6

Accessory Violet/Yellow 3 (+) Ignition Control Switch Black 6

Parking Lights Green/Gray 3 (-) Headlight Switch Black 12

DATA Bypass Green/Violet 2 Data Immobilizer Control Module, under ignition switch Violet 3

RAP Off Gray 6 (-) Driver Window Motor, in driver's door Black 7

SW CAN Green 1 Data OBDII Black 16

CAN High Blue 6 Data OBDII Black 16

CAN Low White 14 Data OBDII Black 16

Ignition Pink 1 (+) Ignition Switch Black 6

Accessory Brown 3 (+) Ignition Switch Black 6

Parking Lights Lt. Blue 3 (-) Headlight Switch Black 12

Immo. Data Lt. Blue 2 Data Immo. Control Module, under Ignition Switch Violet 3

RAP Off Gray/Black 6 (-) Driver Window Motor Black 7

SW CAN Dk. Green 1 Data OBDII Connector Black 16

CAN High Tan/Black 6 Data OBDII Connector Black 16

CAN Low Tan 14 Data OBDII Connector Black 16

Ignition Violet 1 (+) Ignition Switch Black 6

Accessory Violet 3 (+) Ignition Switch Black 6

Parking Lights Lt. Green 3 (-) Headlight Switch Black 12

Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3

RAP Off Gray 6 (-) Driver Window Motor Black 7

SW CAN Green 1 Data OBDII Connector Black 16

CAN High Dk. Blue 6 Data OBDII Connector Black 16

CAN Low White 14 Data OBDII Connector Black 16

Ignition Violet/Black 1 (+) Ignition Switch Black 6

Accessory Violet/Yellow 3 (+) Ignition Switch Black 6

Parking Lights Green/Brown 3 (-) Headlight Switch Black 12







Accessory Lt. Green 3 (+) Ignition Switch Black 6

Parking Lights Lt. Green 3 (-) Headlight Switch Black 12



SW CAN Lt. Green 1 Data OBDII Connector Black 16






Immo. Data Lt. Green/White or Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3



CAN High Blue 6 Data OBDII Connector Black 16


Buick LaCrosse 2013

Buick LaCrosse 2014

Buick Regal 2011

Wire Information Connector Information

Buick Encore 2013-2015

Buick LaCrosse 2010

Buick LaCrosse 2011-2012

Rev.: 20160118






















Ignition Pink 1 (+) Ignition Switch White 6

Accessory Brown 3 (+) Ignition Switch White 6



RAP Off Gray/Black 6 (-) Driver Window Motor Black 7








Gray 6 (-) Driver Window Switch (driver window auto down only) Black 8

Gray 6 Data Driver Window Motor (driver window auto up & down) Black 7








RAP Off Gray/Black 6 (-) Driver Window Switch Black 8












Buick Regal 2012-2015

Buick Verano 2012-2015


Chevrolet Camaro 2010-2015

Chevrolet Cruze 2011-2014

RAP Off

Chevrolet Equinox 2010-2015

Chevrolet Impala 2014-2015

Rev.: 20160118







Accessory Yellow 3 (+) Ignition Switch Black 6

Parking Lights Gray 3 (-) Headlight Switch Black 12


Gray 6 (-) Driver Window Switch (driver window auto down only) Black 8

Gray 6 (-) Driver Window Motor (driver window auto up & down) Black 7












Ignition Violet/Black 1 (+) Ignition Switch White 6

Accessory Violet/Yellow 3 (+) Ignition Switch White 6



Gray 22 (-) BCM - under driver dash (without power windows) Pink 27

Gray 6 (-) Driver Window Motor (with power windows) Black 7





















GMC Terrain 2010-2015

Chevrolet Malibu 2013-2015

RAP Off

Chevrolet Orlando 2012-2013

Chevrolet Sonic 2012-2015

RAP Off

Chevrolet Trax 2013-2016

1 2 3 4 5

7

6

121198 10

Type 2a (Without T-Harness)



[2] ONLY if vehicle is NOT equipped with OnStar.


SW Can: Green, pin 1

CAN High: Blue, pin 6


CAN Low:White,pin 14

(+) 12V:pin 16


321

Immo. Data:Green/Violet, pin 2


black connector)

Cut

TX

(-) Ground

RX

(+)12V

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12


1 8

169


Hood Pin



BCM (under driver-side of dash)





(+) 12V: Brown: 7

Immo. Data (veh. side): Yellow/Red: 11


(+) 12V: Red: 13





Immo. Data (veh.side): Orange/Black: 11




HS CAN Low: Tan: 4

[2] (-) Lock Output: Red/Black: 4

[2] (-) Unlock Output: Blue/Red: 12

(-) Lock:Brown/Yellow,pin 19

(-) Unlock:Brown/White,pin 15

[2] ONLY if vehicle is NOT equipped with OnStar

41

8

9

16

22

17 18 20 21

23 24 26 27

15

19

5

Lt. Blue

654321

(+) Ignition: Violet/Black, pin 2

(+) Accessory: Violet/Yellow, pin 3

Ignition Switch


2 3

6 7

10 11 12 13 14

Refer to the Vehicle Wiring Reference Charts (page10-15) for wire color and location.

(-) Parking Lights:Green/Gray, pin 5

Rev.: 20160118



1 2 3 4 5

7

6

121198 10

Type 2b - THGM610 Rev. 1 (With T-Harness)

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+) 12V


Ignition Switch

Use connectors labeled GM10

[1] (-) RAP Off: Green/Black

(-) Parking Lights Output: Black/White


Trigger [1]

n/a: Violet/Green

n/a: Violet/Brown

n/a:Pink


Hood Pin


Wh

ite/B

lack


Ignition Barrel

Cut away the 4-pin connector and connect

the three wires to the OBDII 16-pin connector.

OBDII Diagnostic Connector (connector side view)1 8

169


Tan

/Bla

ck

CAN Low: White, pin 14

Tan


Lt. G

reenTo

Immobilizer Control

Module (ICM)(vehicle side)

GM10 GM10

T-01

GM06NOT USED







T-02

NOT USED

Lock and Unlock will only function if vehicle is equipped with OnStar.

(-) Parking Lights:Green/Gray, pin 5


T-02

Chevrolet Colorado

Chevrolet Silverado 1500

Chevrolet Silverado 2500/3500

Chevrolet Suburban

Chevrolet Tahoe

GMC Canyon

GMC Sierra 1500

GMC Sierra 2500/3500

GMC Yukon

Rev.: 20160118



Type 2c - THGM610 Rev. 2 (With T-Harness)



Lock and Unlock will only function if vehicle is equipped with OnStar.

Ignition Barrel

XKD2D65

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+) 12V



Ignition Connector


(-) Driver Door Sense Trigger [2]


GM10 GM10

Use connectors labeled GM10.

To Immobilizer Control Module (ICM)(vehicle side)

[2] RAP Off: Green/Black

Diagnostic ConnectorOBDII (connector side view)

1 8

169


CAN Low: White, pin 14

Lt.G

ree

n

Tan

Tan

/Bla

ck

NOT USED

Light Switch Connector 1 2 3 4 5

7

6

121198 10

(-) Parking Lights: Green/Gray, pin 5

GM06

NOT USED


T-01

T-02

n/a: Pink

(-) Parking Lights Output:Black/White


Hood Pin


Wh

ite/B

lack

Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.

T-02

Chevrolet Colorado

Chevrolet Silverado 1500

Chevrolet Silverado 2500/3500

Chevrolet Suburban

Chevrolet Tahoe

GMC Canyon

GMC Sierra 1500

GMC Sierra 2500/3500

GMC Yukon

Rev.: 20160118



Rev.: 20160118








Parking Lights Lt. Green/Gray 5 (-) Headlight Switch Black 12

Immo. Data Lt. Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3


SW CAN Lt Green 1 Data OBDII Connector Black 16

CAN High Lt. Blue 6 Data OBDII Connector Black 16






Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
































RAP Off

Chevrolet Silverado 2500/3500 2015

RAP Off

Chevrolet Suburban 2015

RAP Off

Chevrolet Tahoe 2015


Chevrolet Colorado 2015

Chevrolet Silverado 1500 2014-2015

RAP Off

Rev.: 20160118








Parking Lights Lt.Green/Gray 5 (-) Headlight Switch Black 12

Immo. Data Lt.Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3


SW CAN Lt.Green 1 Data OBDII Connector Black 16

CAN High Lt. Blue 6 Data OBDII Connector Black 16






























RAP Off

GMC Yukon 2015

RAP Off

GMC Canyon 2015

GMC Sierra 1500 2014-2015

RAP Off

GMC Sierra 2500/3500 2015

145 236

Type 3







CAN Low:White, pin 1

(+) 12V:Red/Brown,pin 16


321

Immo.Data: Green/Violet, pin 2


black connector)

Cut

TX

(-) Ground

RX

(+)12V

10

DBALL/DBALL2

RF

Prog. Button

LED

4

14

12


1 8

169


Hood Pin







(+) 12V: Brown: 7

Immo. Data (veh.side): Yellow/Red: 11


(+) 12V: Red: 13





Immo. Data (veh. side): Orange/Black: 11




HS CAN Low: Tan: 4

(+) Ignition: Violet/Black, pin 4

(+) Accessory: Violet/Yellow, pin 6

Ignition Switch


54321

986 7

Refer to the Vehicle Wiring Reference Charts (page 10-15) for wire color and location.

(-) Parking Lights: Green/Gray, pin 2

Rev.: 20160118



Rev.: 20160118






Ignition Violet/Black 4 (+) Ignition switch. Gray 6

Accessory Violet/Yellow 6 (+) Ignition switch. Gray 6



RAP Off Gray 22 (-) BCM, above driver kick panel Pink 27





Chevrolet Spark 2013-2014

SmartStart/XL202 Installation Notes

The optional XL202 and antenna are not included and MUST be purchased separately.

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

4

4

XL202

An

ten

na

XOVER

SmartStart is optional and not included. It MUST be purchased separately.

SmartStart is optional and not included. It MUST be purchased separately.

Configuration Wires (Gray & White)Connect Gray wire to (-) Ground

5 pins

D2D (4 pins, white)

4 pins

2 pins, not usedCABLE

CABLE

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

SmartStart Revision B

RF Kit

RF Kit & PKE Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

RF Kit, PKE & SmartStart BT Combination

SmartStart Revision A

DBALL/DBALL2

DBALL/DBALL2

DBALL/DBALL2

LED

Prog.Button

D2D (4 pins, white)

4 pins

2 pins, not used

OR

SmartStart

Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop

LED

THIS SIDE UP

LED

The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.

Rev.: 20160118



Module Programming

3

2

4

If the LED flashes orange quickly, skip to step 3. If solid red press theUnlock button on the OEM remote and wait until the LED starts flashingorange; otherwise, skip to step 3.

Remove the key from ignition barrel.

&

&

Key IN OF

F

START

IGN

Key OUT OF

F

START

IGN

Flashes

Flashes

Turn the key to the IGN position. The LED should be flashing green.

Steps 3 to 5 must be executed within 5 seconds.

Go to the next page to complete the module programming.

Press Unlock button

1 10-pinD2D

st1

12-pin14-pin

nd2

rd3

&Solid

Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.

Important

10-pinD2D

XL202

10-pinD2DSmartStart

OR

The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.

a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).

b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.

Connect SmartStart to DBALL using the D2D port.

SmartStart Installation

Connect XL202 to DBALL using the D2D port.

XL202 Installation

Refer to the LED Diagnostics section on page 21 for more information and for troubleshooting purposes.

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.

Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.

When the flashing operation is successful, you can proceed with the programming instructions below.

Flashing a module using your computer:

1. Connect the interface module to your computer using the XKLoader2.

2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.

3. Follow the instructions to select your vehicle, installation type, and configure your options.

4. Once you have configured the firmware options, click on the FLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your XKLoader3.

2. Launch the Directechs Mobile app on your smartphone or tablet.

3. Select FLASH YOUR MODULE and follow the on screen instructions.

Rev.: 20160118



5 Insert the key and turn it to the IGN position. The LED turns ON solid green for 3 seconds then shuts off.

Key IN OF

F

START

IGN

& &

Solid 3x secs Off

6 Remove the key from the ignition barrel.Key OUT O

FF

START

IGN

1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

2

Solid

&Release

3 Release the programming button. The LED turns ON solid red.

Module Reset

Hard Reset

2 & &

1

Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

Solid Release Solid

Solid Flashes

&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.

You have successfully completed the module programming sequence.

Rev.: 20160118



Feature & Option List

It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the features is possible using the information on this page.

Feat. Operation Flashes/Option Description

1. No RF Output* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver priority*Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is

pressed a second time within 5 seconds.

2. All Unlocks all doors when the button is first pressed.

1. Disabled* No action.

2. Enabled for Windows Module will perform windows roll up upon lock command.

3. Enabled for Windows and

SunroofModule will perform windows roll up and close sunroof upon lock command.

1. Disabled* No operation.

2. Enabled When the feature is enabled, it will activate the Heated Seats and heated steering wheel.

1. 32°F (0°C)*When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when

2. 23°F (-5°C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when

3. 41°F (+5°C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when

4. Always ON When Heated Seats or Defroster feature is enabled, it will activate the feature at any temperature.

1. Disabled* The vehicle doors will not lock automatically.

2. Ignition The vehicle doors will lock when ignition is turned ON and unlock when ignition is OFF.

3. Brake The vehicle doors will lock when the brake pedal is applied and unlock when ignition is OFF.

4. Speed The vehicle doors will lock when speed is sensed and unlock when ignition is OFF.

1. Disabled

The OEM alarm will not be controlled by the interface upon remote start. No disarm or arm

command will be executed at the beginning or end of the sequence; it must be controlled by the

Remote Starter.

2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will

unlock at the beginning of the sequence, and relock after start and shutdown.

3. Enabled*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm

the vehicle in the remote start sequence, only when required. Smart OEM Alarm Control will

monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is

unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed.

* Default Option

RFTD Output Type1

Unlock Driver Priority

4

Comfort Closure with

Lock3

2

Smart OEM Alarm

Control7

6Automatic Controlled

Door Lock

Heated

Seats/Defroster

Temperature Control

5

Heated Seats

Rev.: 20160118



To enter feature programming routine Turn the ignition ON, then OFF. Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the

Programming button. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate

the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.

Changing feature options Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the

DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.

The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature Press and release the programming button a number of times to advance from the current feature to the next desired feature. The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to

indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed Other features can be programmed. The feature programming can be exited.

Exiting feature programming No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming

sequence.OR

Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.

Feature ProgrammingProgramming

Button

Rev.: 20160118



LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Module Programming

Waiting to begin the

programming sequence.Make sure that all the connections are correct (see wiring diagram).

VIN skipped. Normal operation

Module has detected ignition.

Waiting for bypass.Normal operation

High Speed CAN detected. Normal operation

Module was successfully

programmed without VIN and

without bypass.

Normal operation


programmed.Normal operation


programmed without VIN or

bypass.

Normal operation

Module Programming - Error codes

High Speed CAN not detected.Check the Tan - Tan/Black wire connections. Wake up the data bus by turning the ignition

on and try again.

Bypass data not detected.Check the bypass line connection. If more than one wire is used, make sure that they are

not inverted.

Bypass processing error. Bypass calculation failed. Reset the module and try again.

VIN not supported.Check the firmware against vehicle year and model coverage. Possible causes are that a

vehicle build date or a country code has yet to be supported.

Key removal timeout

Failed to completely remove the key from ignition or turned the ignition OFF without

removing the key while bypass sequence was executing. Cycle was done without

removing the key. Reset module and retry module programming from step 1.

Key cycle timeout Key cycle out of time or remote out of range.

External Module Synchronisation

OBDII feature not supported. Diagnostic data bus not detected.

Solid red

Flashes red

Flashes green

Flashes orange

Solid red x 3 secs

Solid greenx 3 secs

Solid orangex 3 secs

Flashesred x 3

Flashes red x 2

Flashesred x 10

Flashes red x 4

Flashesred 1xorange 1x

Flashesred 1xorange 2x

Flashesred, red thenorange x 10

Rev.: 20160118



LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Active Ground While Running

GROUND OUT ON (GWR) command

received.

If doesn't flash green, the Ground While Running (status) signal was lost or

was never received by the module.

IGNITION ON command received.If doesn't flash red & orange, the ignition signal was not received by the

module.

START ON command received. If doesn't flash green quicly, the start signal was not received by the module.

D2D and W2W Commands

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.

AUX2 command received.

RSR Code

3x OEM Lock Remote Start Activation was

attempted when RFTD feature is disabled.

Activated from Web automatically when using RSR flash tool or can be done

manually. Refer to feature programing section for more information.

If the bypass module fails to flash, it means the module did not receive the

signal. Commands can come from RF, W2W or D2D.

Flashesgreen

Flashesred &orange

Flashesgreen quickly

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 4

Flashesorange x 5

Flashes red x 7

Rev.: 20160118



Limited One Year Consumer Warranty

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Rev.: 20160118



Quick Reference GuideDBALL/DBALL2-GM10 Remote Start Ready (RSR) Installation


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Remote Start Ready (RSR)

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.

Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.

Flashes Diagnostic

1 Runtime expired.

2 Over-rev shutdown.

3 Low/No RPM.

4 Transmitter shutdown.

5 Brake shutdown.

6 Hood shutdown/Remote start safety override switch is ON*.

7 Remote start safety override switch is ON*.

3x OEM Lock Remote Start Activation

This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.

Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.

* If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.

Quick Reference GuideDBALL/DBALL2-GM10 Remote Start Ready (RSR) Installation


NotesSmartStart Compatible

This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart?

Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:

Lock/Arm Unlock/Disarm Remote Car Starter Trunk Release Panic Aux Channels

You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!

But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.

3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

For more information, visit www.mysmartstart.com.

DBALL-DBALL2-GM10-RSR EN IG TH20150118 · Type 1c - THGM610 Rev. 2 (With T-Harness) Page 5 [1] If...

Documents

Transcript of DBALL-DBALL2-GM10-RSR EN IG TH20150118 · Type 1c - THGM610 Rev. 2 (With T-Harness) Page 5 [1] If...