DBALL-DBALL2-HK3 EN IG PGa20140211 · 2/11/2014 · dball/dball2-hk3
DBALL2-CHRYSLER-RSR EN IG NF20170213 · The CHRYSLER firmware for DBALL2 is an all-in-one door lock...
Transcript of DBALL2-CHRYSLER-RSR EN IG NF20170213 · The CHRYSLER firmware for DBALL2 is an all-in-one door lock...
Vehicle Application Guide......................................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-Harness............................................................................................Type 1 - without T-Harness.............................................................................................................................................Type 2 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-Harness............................................................................................Type 2 - without Tharness...............................................................................................................................................Type 3 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-Harness............................................................................................Type 3 - without T-Harness.............................................................................................................................................Type 4 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-Harness............................................................................................Type 4 - without T-Harness.............................................................................................................................................Type 5 - with CHTHD2 (R9-R10) /THCHD2 (R1) T-Harness..........................................................................................Type 5 - without T-Harness.............................................................................................................................................Type 6 - with CHTHD2 (R9-R10) /THCHD2 (R1) T-Harness.........................................................................................Type 6 - without T-Harness.............................................................................................................................................Type 7...............................................................................................................................................................................SmartStart/XL202 Installation Notes.....................................................................................................................................................
ProgrammingModule Programming for Installation (with Factory Keyless)...............................................................................................................Module Programming for Installation (without Factory Keyless)..........................................................................................................Module Reset........................................................................................................................................................................................Hard Reset............................................................................................................................................................................................Feature & Option List............................................................................................................................................................................Feature Programming...........................................................................................................................................................................
LED Diagnostics & Troubleshooting.....................................................................................................................................................Parking Light Error Codes....................................................................................................................................................Limited One-Year Consumer Warranty..................................................................................................................................................Quick Reference Guide.........................................................................................................................................................................
02
0304060709101213151619202224
252627272829
30323334
Index
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
® Chrysler, Dodge, Jeep, Mitsubishi and Volkswagen are registered trademarks and property of their respective companies.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Important!This product is NOT compatible with vehicles equipped with a manual transmission.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
The CHRYSLER firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Chrysler, Dodge, Jeep, Mitsubishi and Volkswagen vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode with or without a Plug & Play (CHTHD1/THCHD1 or CHTHD2/THCHD2) T-Harness (optional). This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on pages 25-26 for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Vehicle Application GuidePage 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
[2] To select the proper install type, locate the ignition switch connector and select your install type as illustrated below:
ORType 7 vehicles have a (+) Starter wire at pin 4
of the ignition switch
(+) Starter wire in pin 4
1
Connector side view at ignition switch
5 or 6
Type 6 vehicles do not have a (+) Starter wire at the ignition switch
Pin 4 empty
1
Connector side view at ignition switch
5 or 6
[1] Vehicles in Installation Type 7 are NOT T-Harness compatible.
Legend:PK: Transponder & Immobilizer OverrideAV: Horn & Lights ControlsCC: Comfort & Convenience ControlsDL: OE Door Lock & Alarm ControlRS: Remote Start & Engine ControlsSS: Integrated Security & MonitoringST: Function/Feature Status
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
2009
2008
2007
2006
2005
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
AV
-Park
ing
Lig
hts
Contr
ol
CC
-Heate
dS
eats
Activ
atio
n
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
olu
sin
g
OE
MR
em
ote
)R
S-3
xLO
CK
ST
OP
(Sto
pcontr
olu
sin
g
OE
MR
em
ote
)R
S-R
AP
ShutD
ow
n(R
eta
ined
AC
C
Pow
er)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
SS
-Facto
ryA
larm
Trigger
Monito
ring
ST
-Bra
ke
Sta
tus
(footbra
ke)
Chrysler
200 5 5 5 5 • • • • • • • • • • • • • • • • • • •
300/300c 3 3 3 • • • • • • • • • • • • • • • • • • •
300/300c [1] 7 [2] 7 [2] 7 [2] • • • • • • • • • • • • • • • • • • • •
Aspen 5 5 5 • • • • • • • • • • • • • • • • • • •
PT Cruiser [1] 7 [2] 7 [2] 7 [2] 7 [2] 7 [2] • • • • • • • • • • • • • • • • • •
Sebring 5 5 5 5 • • • • • • • • • • • • • • • • • • •
Sebring Convertible 5 5 5 • • • • • • • • • • • • • • • • • • •
Sebring Sedan 5 5 5 5 • • • • • • • • • • • • • • • • • • •
Town & Country 2 2 2 2 2 2 1 1 1 • • • • • • • • • • • • • • • • • • • • •
Dodge/Ram 17 16 15 14 13 12 11 10 09 08 07 06 05
1500 1 1 • • • • • • • • • • • • • • • • •
2500 1 1 • • • • • • • • • • • • • • • • •
3500 1 1 • • • • • • • • • • • • • • • • •
Avenger 5 5 5 5 5 5 5 • • • • • • • • • • • • • • • • • • •
C/V 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • •
Caliber 5 5 5 5 5 5 • • • • • • • • • • • • • • • • • •
Challenger 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • •
Challenger (Smart Key) 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • •
Charger 3 3 3 • • • • • • • • • • • • • • • • • • •
Charger [1] 7 [2] 7 [2] • • • • • • • • • • • • • • • • • • • •
Dakota 5 5 5 5 5 • • • • • • • • • • • • • • • • •
Durango 2 2 2 5 5 5 • • • • • • • • • • • • • • • • • •
Grand Caravan 2 2 2 2 2 2 2 1 1 1 • • • • • • • • • • • • • • • • • • • • •
Journey 1 1 • • • • • • • • • • • • • • • • • •
Magnum 3 • • • • • • • • • • • • • • • • • •
Magnum [1] 7 [2] 7 [2] 7 [2] • • • • • • • • • • • • • • • • • • • •
Nitro 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] • • • • • • • • • • • • • • • • • •
RAM* 1 1 6 [2] 6 [2] 7 [2] • • • • • • • • • • • • • • • • •
Jeep 17 16 15 14 13 12 11 10 09 08 07 06 05
Commander [1] 4 4 4 7 [2] 7 [2] • • • • • • • • • • • • • • • • • • •
Compass 5 5 5 5 5 5 5 5 5 5 • • • • • • • • • • • • • • • • • •
Grand Cherokee 1 1 1 4 4 4 • • • • • • • • • • • • • • • • • •
Grand Cherokee [1] 7 [2] 7 [2] 7 [2] • • • • • • • • • • • • • • • • • • •
Grand Cherokee (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • •
Liberty 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] • • • • • • • • • • • • • • • • • •
Patriot 5 5 5 5 5 5 5 5 5 5 • • • • • • • • • • • • • • • • • •
Wrangler 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] 6 [2] • • • • • • • • • • • • • • • • • •
Mitsubishi 17 16 15 14 13 12 11 10 09 08 07 06 05
Raider 5 5 5 • • • • • • • • • • • • • • • • •
Volkswagen 17 16 15 14 13 12 11 10 09 08 07 06 05
Routan 2 2 2 1 1 • • • • • • • • • • • • • • • • • • • • •
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
2
7 8 9
3 4 5
6 10
1
Headlight switch(black 10-pin conn.)
(-) RAP Off Output: Yellow/Black: 10
Parking Light MUX Output: Violet/Green: 8
Parking Light MUX Output: Violet/Brown: 9
Ignition Barrel
12-pin Connector(Vehicle side)
12-pin Connector(harness side)12-pin Connector
(harness side)
PUSHTO
RELEASE
Driver Kick Panel
(-) Driver Door Trigger: Violet
(MUX) Parking Lights:
Pin 1
[1] (+) Parking Lights: White/Violet, pin 3
[1] Parking Light Output: Green/Black: 2
Connect parking lights in drivers kick panel for Dodge Journey only.
Refer to the Vehicle Wiring Reference Charts for wire color and location.
This is the only connection required for the parking light output for the Dodge Journey. The DBALL MUX connection is not required.
30
86 8587
87a
Dodge Journey(+) Parking Lights
White/Violet
Fuse 15A
+12V
ONLY connect for Dodge Journey.
CHTHD1 (R1-R7)/ THCHD1 (R1)
(optional)
Installation Type 1 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-HarnessPage 3
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
All connectors are displayed from the wire side (unless specified otherwise).
[1] Connected to the Dodge Journey only. DO NOT connect Parking Light Input to (+)12V at the ignition switch.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
2
7 8 9
3 4 5
6 10
1
PUSHTO
RELEASE
Driver Kick Panel
(-) Driver Door Trigger: Violet
Headlight switch(black 10-pin conn.)
(MUX) Parking Lights:
Pin 1
16
12 7
(+) Ig
nitio
n: P
ink/W
hite
, pin
3
(+) 1
2V
:Lt.B
lue/R
ed
,pin
1
(-) Gro
und: B
lack/S
triped
, pin
4
HS
CA
N H
igh: P
in 5
HS
CA
N L
ow
: Pin
6
Ignition Barrel
Ignition switch
[1] (+) Parking Lights: White/Violet, pin 3
Refer to the Vehicle Wiring Reference Charts for wire color and location.
Connect parking lights in drivers kick panel for Dodge Journey only.
30
86 8587
87a
Dodge Journey(+) Parking Lights
White/Violet
Fuse 15A
+12V
ONLY connect for Dodge Journey.
This is the only connection required for the parking light output for the Dodge Journey. The DBALL MUX connection is not required.
(Connector side view)
CUT
Page 4
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
All connectors are displayed from the wire side (unless specified otherwise).
[1] Connected to the Dodge Journey only. DO NOT connect Parking Light Input to (+)12V at the ignition switch.
Installation Type 1 - without T-Harness
(MUX) Parking Lights Output: Violet/Green: 8
(MUX) Parking Lights Output: Violet/Brown: 9
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Ignition Interrupt (vehicle side): Yellow: 8
Ignition Interrupt (conn. side): Orange/Yellow: 9
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
[1] (-) Parking Light Output: Green/Black: 2
(-) RAP Off Output: Yellow/Black: 10
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 5
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Chrysler Town & Country 2008-2010
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Brown 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge RAM 1500 /2500/3500 2011-2012
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge Grand Caravan 2008-2010
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Brown 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge Journey 2009-2010
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
12V Battery Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Violet N/A (+) Drivers kick, harness to rear. N/A N/A
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge RAM 2009-2010
HS CAN High White/Lt.Green 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Jeep Grand Cherokee 2011-2013
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Lt.Green 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Jeep Grand Cherokee (Smart Key) 2011-2013
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Volkswagen Routan 2009-2010
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Brown 1 MUX Headlight switch. Black 10
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Ignition Barrel
12-pin Connector(Vehicle side)
12-pin Connector(harness side)12-pin Connector
(harness side)
PUSHTO
RELEASE
Driver Kick Panel
(-) Driver Door Trigger: Violet
Headlight switch(black 6-pin conn.)
6
5
4
3
2
1
(MUX) Parking Lights: Pin 3
Refer to the Vehicle Wiring Reference Charts for wire color and location.
(MUX) Parking Lights Output: Violet/Green: 8
(MUX) Parking Lights Output: Violet/Brown: 9
(-) RAP Off Output: Yellow/Black: 10
CHTHD1 (R1-R7)/ THCHD1 (R1)
(optional)
Installation Type 2 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-HarnessPage 6
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
(MUX) Parking Lights Output: Violet/Green: 8
(MUX) Parking Lights Output: Violet/Brown: 9
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Ignition Interrupt (vehicle side): Yellow: 8
Ignition Interrupt (conn. side): Orange/Yellow: 9
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
PUSHTO
RELEASE
Driver Kick Panel
(-) Driver Door Trigger: Violet
(MUX) Parking Lights:
Pin 3
16
12 7
(+) Ig
nitio
n: P
ink/W
hite
, pin
3
(+) 1
2V
:Lt.B
lue/R
ed
,pin
1
(-) Gro
und: B
lack/S
triped
, pin
4
HS
CA
N H
igh: P
in 5
HS
CA
N L
ow
: Pin
6
Ignition Barrel
Headlight switch(black 6-pin conn.)
6
5
4
3
2
1
(-) RAP Off Output: Yellow/Black: 10
Refer to the Vehicle Wiring Reference Charts for wire color and location.
CUT
Ignition switch(Connector side view)
Installation Type 2 - without T-HarnessPage 7
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 8
Type 2 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Chrysler Town & Country 2011-2016
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 3 MUX Headlight switch. Black 6
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge C/V 2012-2016
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 3 MUX Headlight switch. Black 6
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Dodge Durango 2011-2013
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 3 MUX Headlight switch. Black 6
Driver Door Trigger Violet N/A N/A Divers kick door harness. N/A N/A
Dodge Grand Caravan 2011-2017
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 3 MUX Headlight switch. Black 6
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Volkswagen Routan 2011-2013
HS CAN High White/Lt.Blue 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Brown 6 Data Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Parking Lights White/Green 3 MUX Headlight switch. Black 6
Driver Door Trigger Violet N/A N/A Drivers kick door harness. N/A N/A
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Twisted pair at the steering column or behind radio
FT CAN Low: Orange/Brown
(-) Parking Lights Output: Green/Black: 2
CHTHD1 (R1-R7)/ THCHD1 (R1)
(optional)
12-pin Connector(Vehicle side)Ignition
Barrel
12-pin Connector(harness side)12-pin Connector
(harness side)
(-) Driver Door Trigger: Violet
Driver Kick
Panel
FT CAN High: Orange/Green
(-) RAP Off Output: Yellow/Black: 10
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Refer to the Vehicle Wiring Reference Charts for wire color and location.
Passenger kick panel, harness to rear
(+) 12V:Red/White
(+) Parking Lights:White/Violet
White/Orange
White/Gray, WhiteWhite/Pink or White Black
Installation Type 3 - with CHTHD1 (R1-R7) /THCHD1 (R1) T-HarnessPage 9
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Ignition Barrel
HS
CA
N H
igh:W
hite
/Bla
ck
or W
hite
/Lt. G
reen
, pin
5
HS
CA
N L
ow
: Wh
ite/L
t. Blu
e, p
in 6
16
12 7
(-) Parking Lights Output: Green/Black: 2
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
Twisted pair at the steering column or behind radio
Ignition Switch (connector side view)
Ignition Interrupt (vehicle side): Yellow: 8
Ignition Interrupt (conn.side): Orange/Yellow: 9
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ig
nitio
n: P
ink
/Wh
ite, p
in 3
(-) Gro
un
d: B
lac
k/S
tripe
d, p
in 4 (-) Driver Door
Trigger: Violet
Driver Kick
Panel
(+) Parking Lights:White/Violet
(+) 12V:Red/White
Passenger kick panel, harness to rear
(-) RAP Off Output: Yellow/Black: 10
Refer to the Vehicle Wiring Reference Charts for wire color and location.
White/Orange
White/Gray, WhiteWhite/Pink or White Black
CUT
Installation Type 3 - without T-HarnessPage 10
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 11
Type 3 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Chrysler 300/300c 2008-2010
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ground Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red/White N/A (+) Passenger kick, harness to rear. N/A N/A
Parking Light White/Violet N/A (+) Passenger kick, harness to rear. N/A N/A
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 3 (-) Instrument cluster or driver kick. White 26
Dodge Challenger / Challenger (Smart Key) 2008-2014
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ground Black or Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red/White N/A (+) Passenger kick, harness to rear. N/A N/A
Parking Lights White/Violet N/A (+) Passenger kick, harness to rear. N/A N/A
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 3 (-) Instrument cluster or driver kick. White 26
Dodge Charger 2008-2010
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ground Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red/White N/A (+) Passenger kick, harness to rear. N/A N/A
Parking Light White/Violet N/A (+) Passenger kick, harness to rear. N/A N/A
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 3 (-) Instrument cluster or driver kick. White 26
Dodge Magnum 2008
HS CAN High White/Black 5 Data Wireless Ignition Node on ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Wireless Ignition Node on ignition switch. Black 12
Ground Black/Striped 4 (-) Wireless Ignition Node on ignition switch. Black 12
Ignition Pink/White 3 (+) Wireless Ignition Node on ignition switch. Black 12
12V Red/White N/A (+) Passenger kick, harness to rear. N/A N/A
Parking Lights White/Violet N/A (+) Passenger kick, harness to rear. N/A N/A
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 3 (-) Instrument cluster or driver kick. White 26
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Twisted pair at the steering column or behind radioWhite/Orange
White/Gray, White,White/Pink or White/Black
FT CAN High: Orange/GreenFT CAN Low: Orange/Brown
(-) Parking Lights Output: Green/Black: 2
CHTHD1 (R1-R7)/ THCHD1 (R1)
(optional)
12-pin Connector(Vehicle side)Ignition
Barrel
12-pin Connector(harness side)12-pin Connector
(harness side)
2011
1 105
Driver Door Module(brown 20-pin conn.)
2 3 4 6 7 8
15
9
12 13 14 16 18 1917
(-) Driver Door Trigger: Violet, pin 5
Hazard light switch(black 12-pin conn.)
1 2 3 4 5 6
7 8 9 10 11 12
(-) Hazard Lights: White/Dk.Blue, pin 4
(-) RAP Off Output: Yellow/Black: 10
Refer to the Vehicle Wiring Reference Charts for wire color and location.
Installation Type 4 - with CHTHD1 (R1-R7) / THCHD1 (R1) T-HarnessPage 12
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Ignition Barrel
HS
CA
N H
igh:W
hite
/Bla
ck o
r Wh
ite/L
t. Gre
en
, pin
5
HS
CA
N L
ow
: Wh
ite/L
t. Blu
e, p
in 6
16
12 7
(-) RAP Off Output: Yellow/Black: 10
(-) Parking Lights Output: Green/Black: 2
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
Twisted pair at the steering column or behind radioWhite/Orange
White/Gray, WhiteWhite/Pink or White Black
Ignition Switch (connector side view)
Ignition Interupt (vehicle side): Yellow: 8
Ignition Interrupt (conn.side): Orange/Yellow: 9
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ig
nitio
n: P
ink
/Wh
ite, p
in 3
(+) 1
2V
:Lt.B
lue
/Re
d, p
in 1
(-) Gro
un
d: B
lac
k/S
tripe
d, p
in 4
2011
1 105
Driver Door Module(brown 20-pin conn.)
2 3 4 6 7 8
15
9
12 13 14 16 18 1917
(-) Driver Door Trigger: Violet, pin 5
Hazard light switch(black 12-pin conn.)
1 2 3 4 5 6
7 8 9 10 11 12
(-) Hazard Lights: White/Dk.Blue, pin 4
Refer to the Vehicle Wiring Reference Charts for wire color and location.
CUT
Installation Type 4 - without T-HarnessPage 13
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
All connectors are displayed from the wire side (unless specified otherwise).
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 14
Type 4 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Jeep Commander 2008-2010
HS CAN High White/Lt.Green 5 Data Ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Ignition switch. Black 12
Ground Black/Striped 4 (-) Ignition switch. Black 12
Ignition Pink/White 3 (+) Ignition switch. Black 12
Parking Light White/Dk.Blue 4 (-) Hazard light switch. Black 12
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 5 (-) Driver Door Module. Brown 20
Jeep Grand Cherokee 2008-2010
HS CAN High White/Black 5 Data Ignition switch. Black 12
HS CAN Low White/Lt.Blue 6 Data Ignition switch. Black 12
12V Lt.Blue/Red 1 (+) Ignition switch. Black 12
Ground Black/Striped 4 (-) Ignition switch. Black 12
Ignition Pink/White 3 (+) Ignition switch. Black 12
Parking Light White/Dk.Blue 4 (-) Hazard light switch. Black 12
FT CAN High White/Orange N/A Data Twisted pair at steering column or behind radio. N/A N/A
FT CAN LowWhite/Gray, White or
White/PinkN/A Data Twisted pair at steering column or behind radio. N/A N/A
Driver Door Trigger Violet 5 (-) Driver Door Module. Brown 20
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
(-) Parking Lights Output: Green/Black
N.C.
8-pin Connectorat ignition switch
(Vehicle side)
8-pin Connector(harness side)
8-pin Connector(harness side)
Ignition Switch
T-04
HS CAN High: Orange/Green
HS CAN Low: Orange/Brown
Diagnostic Connector OBDII(connector side view)
1 8
169
HS CAN High: Pin 6
HS CAN Low: Pin 14
(+) Parking lights:White/Violet
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Driver Door Trigger
Refer to the Vehiclewiring reference chart.
(+) 12V
Refer to the Vehiclewiring reference chart.
Drivers kickharness to rear
Installation Type 5 - with CHTHD2 (R1-R6 & R9-R10) /THCHD2 (R1) T-HarnessPage 15
TX
(-) Ground
RX
(+) 12V
10
DBALL2Prog. Button
LED
4
14
12
2
(-) RAP Off Output: Yellow/Black
RF
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
N.C.
8-pin Connectorat ignition switch
(Vehicle side)
8-pin Connector(harness side)
8-pin Connector(harness side)
T-04
Remote Start Safety Override Switch
Hood Pin
White/Black
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
1 8
169
HS CAN High: Pin 6
HS CAN Low: Pin 14
(+) Parking lights:White/Violet
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Refer to the Vehicle Wiring Reference Charts for wire color and location.
Driver Door Trigger
Refer to the Vehiclewiring reference chart.
(+) 12V
Refer to the Vehiclewiring reference chart.
Drivers kickharness to rear
CHTHD2 (R1-R6 & R9-10)/ THCHD2 (R1)
(optional)
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Drivers kickharness to rear
(+) Parking LightsWhite/ Violet
FT CAN High: Tan/Black: 3F
T C
AN
Low
:Wh
ite
or W
hite
/Pin
k ,
pin
7
FT
CA
N H
igh
:
Wh
ite/O
ran
ge
, p
in 6
1 8Sentry Key Module
(black 8-pin conn.)
FT CAN Low: Tan: 4
(-) Ground: Black: 14
(+) 12V: Red: 13
(+) Ignition Output: Yellow: 8
(MUX) Ign. Output: Violet/Green: 8
(MUX) Ign. Output: Violet/Brown: 9
(-) P.K. Lights Output: Green/Black: 2
(+) 12V: Brown: 7
(+) 12V: Brown/Red: 12
(+) 12V: Red orRed/Striped, pin 5
(-) Ground:Black or
Black/Striped,pin 4
HS CAN High: Orange/Green: 5
HS CAN Low: Orange/Brown: 6
Diagnostic Connector OBDII(connector side view)
1 8
169
HS CAN High: Green, pin 6
HS CAN Low: Orange, pin 14
(MU
X) Ig
nitio
n:
Vio
let/B
row
n,
pin
1
(+) Ig
nitio
n:
Pin
k o
r Pin
k/S
tiped
,pin
3
(-) RAP Off Output: Yellow/Black: 10
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Refer to the Vehicle Wiring Reference Charts for wire color and location.
(+) 12V
Refer to the Vehiclewiring reference chart.
Driver Door Trigger
Refer to the Vehiclewiring reference chart.
Installation Type 5 - without T-HarnessPage 16
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 17
Type 5 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Chrysler 200 2011-2014
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High White/Lt/Blue 6 Data OBDII diagnostic connector. Black 16
HS CAN Low White/Dk.Blue 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red 3 (-) Junction connector above drivers kick panel. Green 43
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Chrysler Aspen 2007-2009
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red/Gray 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High White/Pink 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Pink/Red 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red/Gray 1 (-) Driver kick panel fuse box. Black 40
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Chrysler Sebring 2007-2010
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red 4 (-) Junction connector above drivers kick panel. Green 43
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Chrysler Sebring Convertible 2008-2010
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red 4 (-) Junction connector above drivers kick panel. Green 43
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Chrysler Sebring Sedan 2007-2010
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Tan/Red 4 (+) Junction connector above drivers kick panel. Green 43
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Dodge Avenger 2008-2014
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red 4 (+) Battery or TIPM on passenger fender. N/A N/A
Driver Door Trigger Violet 14 (-) Under driver dash. Lt.Gray 43
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Type 5 - Vehicle Wiring Reference ChartPage 18
Function Color Pin Polarity Location Color Pins
Dodge Caliber 2007-2012
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Pink 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay power Red N/A (+) Battery or TIPM on passenger fender. N/A N/A
Driver Door Trigger Violet/Dk. Blue 17 (-) Under driver dash. Black 43
Dodge Dakota 2007-2011
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Pink or White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Driver Door Trigger Violet or Violet/White 13 (-) Under driver dash above kick panel. Black 72
Dodge Durango 2007-2009
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Pink 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Orange/Dk.Blue 39 (+) Drivers kick panel fuse box. Gray 40
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Driver Door Trigger Violet 5 (-) Drivers door module in drivers door. Brown 20
Jeep Compass 2007-2016
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch Black 8
FT CAN Low White/Pink 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet/Dk. Blue 17 (-) Under drivers dash. Black 43
Jeep Patriot 2007-2016
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Pink 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
HS CAN High Green 6 Data OBDII diagnostic connector. Black 16
HS CAN Low Orange 14 Data OBDII diagnostic connector. Black 16
Parking Lights White/Violet N/A (+) Driver kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet/Dk. Blue 17 (-) Under drivers dash. Black 43
Mitsubishi Raider 2007-2009
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
Parking Lights White/Violet N/A (+) Driver kick panel. N/A N/A
Parking Light Relay Power Re 2 (+) Connector above drivers kick panel. White 3
Driver Door Trigger Violet 13 (-) Under drivers dash above kick panel. Black 72
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
(-) RAP Off Output: Yellow/Black
(-) Parking Lights Output: Green/Black
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
8-pin Connectorat ignition switch
(Vehicle side)
Sentry Key Modulenear Ignition Switch
CHTHD2 (R1-R6 & R9-10)/ THCHD2 (R1)
(optional)
8-pin Connector(harness side)
8-pin Connector(harness side)
Drivers or passenger kickharness to rear
(+) Parking LightsWhite/ Violet
Refer to the Vehicle Wiring Reference Charts for wire color and location.
(+) 12V
Refer to the Vehiclewiring reference chart.
Driver Door Trigger
Refer to the Vehiclewiring reference chart.
Installation Type 6 - with CHTHD2 (R1-R6 & R9-R10) /THCHD2 (R1) T-HarnessPage 19
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
CUT
T-04
For CHTHD2 R9-R10:If the vehicles security light remains ON after performing
a remote start takeover, then Cut the Violet/Brown T-04 loop found on the T-Harness.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
FT CAN High: Tan/Black: 3
(+) Ignition Output: Yellow: 8
FT CAN Low: Tan: 4
FT
CA
N L
ow
: Pin
7
FT
CA
N H
igh: P
in 6
1 8
Sentry Key Module (black 8-pin conn.)
(-) Ground: Black: 14
(+) 12V: Red: 13
(MUX) Ign.Output: Violet/Green: 8
(MUX) Ign. Output: Violet/Brown: 9
(-) RAP Off Output: Yellow/Black: 10
(-) Pk. Lights Output: Green/Black: 2
(+) Ignition Input: Brown: 7
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
(+) Ig
nitio
n:P
ink o
r P
ink/S
tripe
d, p
in 3
MU
X: V
iole
t/Bro
wn
, pin
1
(+) 12V: Red orRed/Striped,pin 5
(-) Ground: Black orBlack/Striped, pin 4
Drivers or passenger kickharness to rear
(+) Parking LightsWhite/ Violet
Refer to the Vehicle Wiring Reference Charts for wire color and location.
(+) 12V
Refer to the Vehiclewiring reference chart.
Driver Door Trigger
Refer to the Vehiclewiring reference chart.
Installation Type 6 - without T-HarnessPage 20
All connectors are displayed from the wire side (unless specified otherwise).
10
DBALL2Prog. Button
LED
4
14
12
2
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood Input
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
If the vehicles security light remains ON after performing a remote start takeover,disconnect the Violet/Brown MUX connection.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Type 6 - Vehicle Wiring Reference ChartPage 21
Function Color Pin Polarity Location Color Pins
Dodge Nitro 2007-2011
FT CAN High White/Black or White/Lt.Green 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Lt.Blue 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
Parking Lights White/Violet N/A (+) Driver kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet N/A (-) Driver kick. N/A N/A
Parking Lights Relay power Red N/A (+) Battery or under hood TIPM. N/A NA
Dodge RAM 2007-2008
FT CAN High White/Black or White/Lt.Green 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Lt.Blue 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Battery or under hood TIPM. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
Parking Lights White/Violet N/A (+) Driver kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet N/A (-) Driver kick. N/A N/A
Parking Lights Relay power Red N/A (+) Battery or under hood TIPM. N/A NA
Jeep Liberty 2008-2012
FT CAN High White/Gray 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Orange 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 4 (+) Driver kick. Gray 43
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
Parking Lights White/Violet N/A (+) Driver kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet N/A (-) Driver door, door harness. N/A N/A
Parking Lights Relay power Red 4 (+) Drivers kick pamel. Gray 43
Jeep Wrangler / Jeep Wrangler Limited 2007-2017
FT CAN High White/Black 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White/Lt.Blue 7 Data Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 1 MUX Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
Parking Lights White/Violet N/A (+) Passenger kick panel harness to rear of vehicle. N/A N/A
Driver Door Trigger Violet N/A (-) Driver kick, door harness. N/A N/A
Parking Lights Relay power Red N/A (+) Battery or under hood TIPM. N/A NA
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
FT CAN High: Tan/Black: 3
FT
CA
N L
ow
:Wh
ite
or W
hite
/Pin
k ,
pin
7
FT
CA
N H
igh
:
Wh
ite/O
ran
ge,
pin
6
1 8
(+) Ig
n.: P
ink/W
hite
or P
ink/G
reen
, pin
3
(+) S
tart: P
in 4
MU
X:
Vio
let/B
row
n,p
in 2
1
Ignition Switch (connector side view)
Sentry Key Module near Ignition Switch (connector side view)
FT CAN Low: Tan: 4
(-) Ground: Black: 14
(+) 12V: Red: 13
(+) Ignition Output: Yellow: 8
(+) Starter Output: Yellow/Red: 11
(MUX) Ign. Output: Violet/Green: 8
(MUX) Ign. Output: Violet/Brown: 9
(-) Pk. Lights Output: Green/Black: 2
(+) Ignition Input: Brown: 7
(+) Starter Input: Brown/Red: 12
(-) Parking Lights
Refer to the Vehiclewiring reference chart.
30
86 8587
87a
To vehicle’s(-) Parking Lights
Fuse 15A
+12V
5-pin or 6-pin
(+) 12V: Red orRed/Striped, pin 5
(-) Ground:Black or
Black/Striped,pin 4
Refer to the Vehicle Wiring Reference Charts for wire color and location.
(+) Parking Lights
30
86 8587
87a
To vehicle’s(+) Parking Lights
Fuse 15A
+12V
Refer to the Vehiclewiring reference chart.
(+) 12V Pk. Light Relay
Refer to the Vehiclewiring reference chart.
OR
(+) 12V Pk. Light Relay
Refer to the Vehiclewiring reference chart.
Installation Type 7Page 22
10
DBALL2Prog. Button
LED
4
14
12
2
RF
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
All connectors are displayed from the wire side (unless specified otherwise).
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Type 7 - Vehicle Wiring Reference ChartPage 23
Function Color Pin Polarity Location Color Pins
Chrysler 300/300c 2005-2007
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Dk. Green 4 (+) Ignition switch. Black 5 or 6
Parking Lights White/Violet N/A (+) Passenger kick panel harness. N/A N/A
Parking Lights Relay Power Red/White N/A (+) Passenger kick panel harness. N/A N/A
Chrsyler PT Cruiser 2006-2010
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/White 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Lt.Blue 4 (+) Ignition switch. Black 5 or 6
Parking Lights White/Violet N/A (+) Driver kick, harness to rear. N/A N/A
Parking Lights Relay Power Lt.Blue/Red 4 (+) Junction connector above OBDII. Black N/A
Dodge Charger 2006-2007
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Orange 4 (+) Ignition switch. Black 5 or 6
Parking Lights White/Violet N/A (+) Passenger kick panel harness. N/A N/A
Parking Lights Relay Power Red/White N/A (+) Passenger kick panel harness. N/A N/A
Dodge Magnum 2005-2007
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Orange 4 (+) Ignition switch. Black 5 or 6
Parking Lights White/Violet N/A (-) Passenger kick panel harness. N/A N/A
Parking Lights Relay Power Red/White N/A (+) Passenger kick panel harness. N/A N/A
Dodge RAM 2006
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Orange 4 (+) Ignition switch. Black 5 or 6
Hazards White/Orange 5 (-) Hazard switch or Instrument cluster. Gray 16
Parking Lights Relay Power Tan/Red 4 (+) Electric brake conn. above junction connector. Blue 4
Jeep Commander 2006-2007
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Orange 4 (+) Ignition switch. Black 5 or 6
Hazards White/Dk. Blue to White/Tan 16 (-) SCM (Steering Column module) in steering column. N/A 16
Parking Lights Relay Power Red 40 (+) Top connector above fuses. Black 40
Jeep Grand Cherokee 2005-2007
FT CAN High White/Orange 6 Data Sentry Key Module near ignition switch. Black 8
FT CAN Low White 7 Data Sentry Key Module near ignition switch. Black 8
12V Red or Red/Striped 5 (+) Sentry Key Module near ignition switch. Black 8
Ground Black or Black/Striped 4 (-) Sentry Key Module near ignition switch. Black 8
MUX Ignition Violet/Brown 2 MUX Ignition switch. Black 5 or 6
Ignition Pink/Green 3 (+) Ignition switch. Black 5 or 6
Starter Pink/Orange 4 (+) Ignition switch. Black 5 or 6
Hazards White/Dk. Blue 16 (-) SCM (Steering Column module) in steering column. N/A 16
Parking Lights Relay Power Red 40 (+) Top connector above fuses. Black 40
Wire Information Connector Information
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
SmartStart/XL202 Installation NotesPage 24
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL2
DBALL2
DBALL2LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
The DBALL2 Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Module Programming (WITH Factory Keyless)Page 25
2 orInsert the key into the ignition barrel and turn it to the ON position.
Key Ignition Push-to-Start (PTS) Ignition
It is important to wait for the LED to start flashing green. Refer to the LED Diagnostics section for troubleshooting if the LED does not flash green within 15 seconds.
Flashes
Green
&Flashes
Green
Key IN OF
F
START
ON It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section for troubleshooting if the LED does not flash green within 15 seconds.
Press the Push-to-Start (PTS) button twice to turn the ignition ON.
Important: Do NOT press the brake pedal.
2XENGINESTARTSTOP
PUSHDo NOT
press the
brake pedal
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Go to the next page to complete the module programming.
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL2, then wait until the LED turns ON solid red.
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL2 module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL2.
a. To ensure that the D2D communication between SmartStart and DBALL2 works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL2 D2D connector.
Connect SmartStart to DBALL2 using the D2D port.
SmartStart Installation
Connect XL202 to DBALL2 using the D2D port.
XL202 Installation
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
3
4
Turn the key to the OFF position and remove it from the ignition barrel.
Press LOCK or UNLOCK on the factory transmitter. The LED turns ON solid green OR orange for 3 seconds and then turns off.
or & &orSolid
Green
Solid
Orange
Off
Key OUT OF
F
START
IGN
orPress the Push-to-Start (PTS) button once more to turn the ignition OFF.
1XENGINESTARTSTOP
PUSH
PAN
IC
Page 26
You have successfully completed the module programming sequence.
2Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green.*
* Refer to the LED Diagnostics section for troubleshooting if the LED does not flash green within 15 seconds.
Key IN OF
F
START
ON
Vehicles WITHOUT Factory Keyless(Refer to the previous page for programming instructions WITH factory keyless).
Press & Release
4Press and release the programming button. The LED turns ON solid green OR orange for 3 seconds and then turns OFF. &
You have successfully completed the module programming sequence.
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL2, then wait until the LED turns ON solid red.
3 Turn the key to the OFF position and remove it from the ignition barrel.
&Flashes
Green
Key OUT OF
F
START
IGN
OffSolid
Orange
Solid
Green
or &
&Solid
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 27
1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
2
Solid
&Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2 & &
1
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web configuration tool will not be affected.
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 28
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
* Default option
Feature Operation Flashes / Option Description
1. Disabled* Module is connected to a remote starter using a standard installation.
2. RFTD OutputModule is connected to an XL202 using an RSR or RXT installation (when
available).
3. SmartStartModule is connected to SmartStart using an RSR or RXT installation (when
available).
1. Driver Priority*Unlocks only the driver door on first press and unlocks all doors on a second
press within 5 seconds.
2. All Unlocks all doors on first press.
1. Trunk* Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Trunk: Will pop the trunk if available.
2. Right Sliding Door* When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Disabled 3./4. Right/Left Sliding Door: When available, will operate the sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door* When available, will operate the left sliding door.
1. Disabled* No operation.
2. Enabled If available, it will activate the Heated Seats Control feature (see feature #7)
1. 32° Farenheit (0° Celsius)*When feature #6 (Heated Seats) is enabled, it will activate the heated seats
upon remote start when temperature is below 32 °F (0 °C).
2. 23° Farenheit (-5° Celsius)When feature #6 (Heated Seats) is enabled, it will activate the heated seats
upon remote start when temperature is below 23 °F (-5 °C).
3. 41° Farenheit (5° Celsius)When feature #6 (Heated Seats) is enabled, it will activate the heated seats
upon remote start when temperature is below 41 °F (5 °C).
4. Always ONWhen feature #6 (Heated Seats) is enabled, it will activate the heated seats
at any temperature.
1. High* When Heated Seats are activated, they will be set to HIGH.
2. Low When Heated Seats are activated, they will be set to LOW.
1. Disabled
The OEM alarm will not be controlled by DBALL upon remote start. No disarm
or arm command will be executed at the beginning or end of the sequence; it
must be controlled by the Remote Starter.
2. Safelock
Smart OEM Alarm Control will behave like a standard Safelock feature on a
remote starter. It will unlock at the beginning of the sequence, and relock after
start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will
disarm and rearm the vehicle in the remote start sequence, only when
required. The reason for this is, factory alarm control must often be done by
lock or unlock operation. This could create unnecessary actions on door lock
modules, such as the horn to honk. When possible, Smart OEM Alarm
Control will monitor the alarm and door lock status to detect if the disarm or
rearm is required. If the vehicle is unlocked or is not equipped with factory
alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will
also monitor the remote starter actions so that the factory alarm control is not
done twice. A remote starter, for which the Safelock feature is active, will work
perfectly with this option and will make it invisible to the user.
8Heated Seats Temperature Level
(Feature 6 must be enabled )
9 Smart OEM Alarm Control
6 Heated Seats
7
Heated Seats/Defrost Temperature
Control
(Feature 6 must be enabled )
Note: If the Heated Steats feature is
activated, it can always be turned on
using the Aux2 command,
regardless of the temperature
setting.
Aux25
Unlock Driver Priority2
1 RF Output Type
3 Trunk
4 Aux1
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Page 29
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL2 in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
LED Diagnostics & TroubleshootingPage 30
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
3x OEM Lock Remote Start Activation was attempted
when RFTD feature is disabled.
Activated from Web automatically when using RSR flash
tool or can be done manually. Refer to feature
programing section for more information.
Feature error.An RSR feature file mismatch was detected. Please
contact Technical Support.
RSR codes
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 7
Flashes redx 9
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Page 31
LED Diagnostics & Troubleshooting
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Parking Light Error CodesPage 32
Platform: DBALL2Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Rev.: 20170214
Limited One Year Consumer WarrantyPage 33
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Vehicle Takeover
5
3
1
1
2
4
Press the remote start button on the transmitter to start the vehicle.*
Stop the vehicle in a safe parking spot and put the gear in Park (P).
2
Press the brake pedal, put the car in gear and drive off.
Enter the vehicle, while making sure the key is inside with you.
Press the Unlock button on the factory or aftermarket remote.*
Ready to drive off
Press remote start
button*
Press remote start
button*
Press Unlock button on
either remote*OR
OR
* Your aftermarket remote may differ from the model shown in the illustrations.
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Exit vehicle with Smart Key
Quick Reference GuideDBALL2-CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Enter vehicle with Smart Key
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
Press the button to remote start the vehicle.*
Note: If the vehicle is equipped with a PTS feature, press the Push-to-Start (PTS) button once before leaving the car.
PANIC
PANIC
PANIC
Insert the key into the ignition barrel and turn it to the ON position.
Key Ignition
Push-to-Start (PTS) Ignition
Press the Push-to-Start (PTS) button twice to turn the ignition ON.
Important: Do NOT press the brake pedal.
2XENGINESTARTSTOP
PUSH
Do NOT
press the
brake pedal
4
Key IN OF
F
START
ON
or
3 Press the PTS button once or remove key from the ignition.
ENGINESTARTSTOP
PUSHKey OUT O
FF
START
ON
Quick Reference GuideDBALL2-CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
3x OEM Lock Remote Start Activation
This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.
Quick Reference GuideDBALL2-CHRYSLER Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Ÿ Lock/ArmŸ Unlock/DisarmŸ Remote Car StarterŸ Trunk ReleaseŸ PanicŸ Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
Notes