CSD – CABIN SAFETY DESIGN
5
CSD – CABIN SAFETY DESIGN Aircraft interior & exterior modifications and changes CSD Competence Center | SA Design
Transcript of CSD – CABIN SAFETY DESIGN
CSD – CABIN SAFETY DESIGNAircraft interior & exterior modifications and changes
CSD Competence Center | SA Design
CSD Competence Center | SA Design – Part of The SA Group
Pfarrwiese 8 | 3443 Sieghartskirchen | Austria | +43 664 91 30 950 | [email protected] | www.scanav.com
SA DESIGN
SA Design - part of The SA Group, develops and designs complex structural and electrical complete turn-key avionics modifications for basically any application and is involved in complete aircraft nose to tail engineering programs.
CSD has been part of the approved scope of SA Design for years, and in order to put more focus and experience on this part of our business, we have built a CSD Competence Center where we can focus 100% on CSD related programs and Customers. Our CSD Competence Center is located close to Vienna, Austria.
The Design & Engineering Department develops various essential documents for certification of avionics and cabin safety related modifications (as a basis for EASA, FAA, military or alternative authorities’ approval), including:
WE PRODUCE HIGH QUALITY INSTALLATION KITS IN-HOUSE
WORK PERFORMED ON MORE THAN 250 DIFFERENT AIRCRAFT TYPES
MORE THAN 40 YEARS OF EXPERIENCE WITH AVIONICS SOLUTIONS
MORE THAN 1.000 CERTIFICATION PACKAGES AND STC’S DEVELOPED
THE SA GROUP IS REPRESENTED IN 9 COUNTRIES, ON 13 LOCATIONS
TE.DOA.00830-005© European Union Aviation Safety Agency. All rights reserved. ISO9001 Certified.
Proprietary document. Copies are not controlled.Confirm revision status through the EASA-Internet/Intranet.
An agency of the European Union
Page 1 of 1
APPROVAL CERTIFICATE EASA.21J.014 Pursuant to Regulations (EU) 2018/1139 and (EU) 748/2012 and
subject to the conditions specified below, the Agency hereby certifies SCANDINAVIAN AVIONICS DESIGN ApS Stratusvej 9 DK-7190 Billund Denmark
as a DESIGN ORGANISATION approved according to Part 21, Section A, Subpart J. CONDITIONS : 1. The approval is limited to that specified in the enclosed Terms of Approval, and
2. This approval requires compliance with the procedures specified in the Design Organisation
Handbook, reference SAD DOM, in the latest revision, and 3. This approval is valid whilst the approved Design Organisation remains in compliance with
Part 21, Section A, Subpart J. 4. Subject to compliance with the foregoing conditions, this approval shall remain valid until
surrendered or revoked. For the European Union Aviation Safety Agency, Date of issue: 05th May 2020
Alexandru Enache Section Manager Design Organisations & Policy Issues
All the above and other relevant documentation can be performed by The SA Group to certify and complete any modification of larger as well as smaller aircrafts and helicopters.
A skilled team of engineers are spread all over The SA Group locations around the world, and our engineers have extensive experience of 40 years+ within the avionics business. The SA Group continues to train and keep the staff up to date with the current requirements and knowledge on the latest equipment, avionics and concepts within the area of avionics and airborne electronics.
Our engineering team are ready to take on any avionics or aircraft electronics challenge.
Technical Orders Certification Programs Cockpit Layouts Wiring Diagrams Structural Drawings Structural Strength Calculations Compliance Records
Load Analysis Weight and Balance Calculations Ground and Flight Test
Procedures Continuous Airworthiness Flight Manual Supplements EMI Assessments
CSD Competence Center | SA Design – Part of The SA Group
Pfarrwiese 8 | 3443 Sieghartskirchen | Austria | +43 664 91 30 950 | [email protected] | www.scanav.com
EXECUTIVE/BUSINESS JET CABIN REFURBISHMENT We provide customised solutions for our Executive/Business Jet operators who
require repairs or changes done to their exclusive cabins. Typical changes or repairs would include but are not limited to work on current
interior such as: ● Seat cushion/dress cover changes ● Carpets changes ● Seat repairs ● Protection covers for seats, carpets and other visible surfaces ● Wooden or other decorative surfaces in the cabin including headliner,
windows and sideliner, dadoo/decorative panels ● Side ledges, tabletops, cabinets, galley changes and repairs thereto ● Structural repairs to cabinets and monuments ● Signs, placards and decals both inside and outside the cabin
CUSTOMISED CABIN LAYOUTS Special mission equipment installation including related cabin modifications Large (temporary) system or equipment installations in the cabin Special mission related installation such as operator seats, restricted emergency
exit egress due to cabinets/consoles etc.
AIRCRAFT PAINT FINISH, LIVERY CHANGES, PLACARDS Signs, placards and decals customised to the required language We provide production support of such signs, placards and decals may be
possible (equipped with a CoC or a Form 1 as appropriate) External paint schemas, Livery changes designed, produced and provided as
kits (as applicable) Design for the application of high performance aviation foil material designed for
durability and capable to be applied on large commercial aircraft Flag & registration mark kits
CABIN SAFETY DESIGN
CSD Competence Center | SA Design – Part of The SA Group
Pfarrwiese 8 | 3443 Sieghartskirchen | Austria | +43 664 91 30 950 | [email protected] | www.scanav.com
LOPA CHANGES ON COMMERCIAL AIRLINERS
(Layout of Passenger Accomodation)
Addressing required cabin re-arrangements to cover new seat arrangements, class seating changes and similar other changes
Seat changes including related compliance demonstration Changes to Emergency Equipment location Modification instructions provided to customised standards
CARGO MODIFICATIONS Support OEMs to develop cargo related modifications to aircraft or aircraft
systems and/or to related ULD’s on aircraft level Changes to the cargo compartment based on customer request
DOCUMENTATION CHANGES Changes to cabin manuals related to LOPA or changes which were not previously
entered into the manuals Proposals for MMEL entries on cabin interior items Amendments to the W&B Manual of the related aircraft
FLIGHT TEST SUPPORT We support flight test activity for the cabin change, if required
DESIGN & ENGINEERING
The SA Group HQ
Billund International Airport | Stratusvej 9 | 7190 Billund | Denmark | +45 7950 8000 | [email protected] | www.scanav.com
WORLDWIDE SERVICE AND SUPPORTThe customer base is geographically spread all over Europe, Africa, CIS, the Middle and Far East. All customers can benefit from the worldwide technical services on-site at the customer’s location, available around the clock.
The worldwide services are carried out from our 13 SA divisions in Europe, the Middle East, India and Southeast Asia. The service centers are manned by well-trained staff and supported by the Original Equipment Manufacturers. All services are based on the required procedures, test equipment, tools and documentation.
Our technical services cover all areas from line service to complete turn-key solutions and are typically performed in close co-operation with the HQ competence center in Billund, Denmark, taking advantage of Group experience and local presence, providing immediate and qualified on-site system troubleshooting, repair and modifications as well as development of certifications (STC’s) according to local, FAA or EASA requirements.
Technical and operational training (EASA Part-147) is provided on world wide basis.
BUSINESS AREAS OF THE SA GROUP
LOGISTICS & PARTS SERVICES
MAINTENANCE - MRO SERVICES
DESIGN, ENGINEERING & STC’S
TRAINING SERVICES
INSTALLATION SERVICES
PRODUCT DEVELOPMENT
PRODUCTION SERVICES
CONSULTANCY SERVICES
[email protected] | www.scanav.com
