Code and Standards List - 2014 (2)
-
Upload
amirrulasyraf -
Category
Documents
-
view
89 -
download
7
description
Transcript of Code and Standards List - 2014 (2)
1 of 24
CODE & STANDARDS LIST
No Code & Standards Title
1 AISCC American Institute of Steel Construction2 ANSI / FCI 70.2 Control Valve Seat Leakage3 ANSI B.18.22.1 Plain Washer4 Bolt and Nut Thread (Unified Coarse Thread)
5 API 2B Specification for the Fabrication of Structural Steel Pipe6 API 2C Offshore Cranes7 API 2W
8 API 2Y
9 API 5L Seamless and Welded Steel Line Pipe10 API 6A
11 API 6AF
12 API 6D Specification for Pipeline Valves13 API 7B-11C
14 API 12J Specification for Oil and Gas Separators15 API 14C
16 API 14E
17 API 14G
18 API 14J
19 API 15HR
20 API 16C API 16C21 API 75
22 API 500
ANSI B1.1 (UNC)/ ANSI B.18.2.2
Specification for Steel Plates for Offshore Structures, Produced by Thermo-Mechanical Control Processing (TMCP)
Specification for Steel Plates, Quenched-and-Tempered, for Offshore Structures
Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition (ISO 10423:2009 Modification), Includes Errata (through November 2013), Addenda 1(Nov 2011), 2 (Nov 2012), 3 (March 2013)
Technical Report on Capabilities of API Flanges under Combinations of Load
Specification for Internal-Combustion Reciprocating Engines for Oil Field Service
Analysis, Design, Installation, and Testing of Basic Surface Safety Systems for Offshore Production Platforms
Recommended Practice for Design and Installation of Offshore Products Platform Piping Systems
Recommended Practice for Fire Prevention and Control on Fixed Open-type Offshore Production Platforms, Fourth Edition
Recommended Practice for Design and Hazards Analysis for Offshore Production Facilities
Specification for High Pressure Fiberglass Line Pipe, Includes Addendum/Errata 1 and Errata 2 (2008)
Recommended Practice for Development of a Safety and Environmental Management Program for Offshore Operations and Facilities
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Division I and Division 2
2 of 24
No Code & Standards Title
23 API 505
24 API 520
25 API 521
26 API 526 Flanged Steel Pressure Relief Valves27 API 534 Heat Recovery Steam Generators28 API 594 Check Valves – Flanged and Water29 API 598 Valve Inspection and Testing30 API 599 Plug Valves31 API 607 Fire test for Quarter Turn Valves32 API 608 Metal Ball Valves Flanged and Welded Ends33 API 609 Butterfly Valves34 API 610
35 API 612
36 API 615 Valve Selection Guide37 API 616
38 API 617
39 API 618
40 API 619
41 API 670 Machinery Protection Systems42 API 674 Positive Displacement Pumps - Reciprocating43 API 675 Positive Displacement Pumps-Controlled Volume44 API 676 Positive Displacement Pumps-Rotary45 API 677
46 API 682 Pumps-Shaft Sealing Systems for Centrifugal and Rotary Pumps
47 API 750 Management of Process Hazards48 API 752
49 API 754
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Zone 0, and Zone 2
Sizing, Selection, and Installation of Pressure-relieving Devices in Refineries, Part I - Sizing and Selection, Eighth Edition
Guide for Pressure-relieving and Depressuring Systems: Petroleum petrochemical and natural gas industries-Pressure relieving and depressuring systems, Fifth Edition (Includes 2008 Addendum)
Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries
API Standard 612, Petroleum, Petrochemical and Natural Gas Industries - Steam Turbines - Special-purpose Applications
Gas Turbines for the Petroleum, Chemical, and Gas Industry Services
Axial and Centrifugal Compressors and Expander-compressors for Petroleum, Chemical and Gas Industry Services
Reciprocating Compressors for Petroleum, Chemical, and Gas Industry Services
Rotary-Type Positive-Displacement Compressors for Petroleum, Petrochemical, and Natural Gas Industries
General Purpose Gear Units for Petroleum, Chemical and Gas Industry Services
Management of Hazards Associated With Location of Process Plant Buildings, CMA Manager's Guide
Process Safety Performance Indicators for the Refining and Petrochemical Industries
3 of 24
No Code & Standards Title
50 API 2000
51 API 2030
52 API 2218
53 API RP 2FPS
54 API RP 2SK
55 API RP 2A WSD
56 API RP 550 Installation of Refinery Instruments and Control Systems57 API RP 551 Process Measurement Instrumentation58 API RP 554 Process Control Systems. 59 API RP 555 Process Analyzers60 API RP 576 Inspection of Pressure Relieving Devices61 API RP 2201
62 API SPEC 2MT1
63 API SPEC 2MT2 Rolled Shapes with Improved Notch Toughness64 API SPEC 2H
65 API SPEC 6FA Specification for Fire test for Valves66 API STD 527 Seat Tightness of Pressure Relief Valves with Metal to Metal Seats
67 API STD 600
68 API STD 602
69 ASCE 41088 Design of Blast-Resistant Buildings in Petrochemical Facilities
70 ASME B1.1 Unified Inch Screw Threads71 ASME B1.20.1 Pipe Thread, General Purpose (Inch)72 ASME B16.1 Cast Iron Pipe Flanges and Flanged Fittings73 ASME B16.5
74 ASME B16.9 Butt Welding Pipe Fittings75 ASME B16.10 Face-to-Face and End-to-End Dimensions of Valves76 ASME B16.11 Fittings Socket Weld and Threaded77 ASME B16.20
78 ASME B16.21 Gaskets Non-Metallic79 ASME B16.25 Buttwelding Ends
Venting Atmospheric and Low-pressure Storage Tanks, Sixth Edition (Identical Adoption of ISO 28300:2008)
Application of Fixed water Spray Systems for Fire Protection in Petroleum and Petrochemical Industries
Fireproofing Practices in Petroleum & Petrochemical Processing Plants
Recommended Practice for Planning, Designing, and Construction Floating Production Systems
Recommended Practice for Design and Analysis of Station keeping Systems for Floating Structures
Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms—Working Stress Design
Safe Hot tapping Practices in the Petroleum and Petrochemical Industries
Specification for Carbon Manganese Steel Plate with Improved Toughness for Offshore Structures
Specification for Carbon Manganese Steel Plate for Offshore Platform Tubular Joints, Ninth Edition
Bolted Bonnet Steel Gate Valves for Petroleum & Natural Gas Industries
Compact Steel Gate Valves, Flanged, Threaded, Welding and Extended-Body Ends
Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
Metallic Gaskets for Pipe Flanges – Ring Joint, Spiral Wound and jacketed
4 of 24
No Code & Standards Title
80 ASME B16.34 Valves Flanged, Threaded and Welding Ends81 ASME B16.36 Orifice Flanges82 ASME B16.47 Flanges Large83 ASME B16.48 Steel Line Blanks84 ASME B31.3 Process Piping85 ASME B31.4
86 ASME B31.8 Gas Transmission and Distribution Piping Systems87 ASME B36.10 Dimensions and Weights of Steel Pipes88 ASME B36.19 Dimensions of Stainless Steel Pipe89 ASME B46.1 Surface Texture (Roughness, Waviness and Lay)90 ASME BPVC Section II Material Specifications (Part A, B and C)91 ASME BPVC Section II Properties (Part D)92 ASME BPVC Section II Properties, Metric (Part IID M)93
94
95 ASME BPVC Section IX Welding and Brazing Qualifications96 ASME PTC 19.3 TW Thermowell Performance Test Codes97 ASME 77 DE 39
98 ASTM
99 ASTM Volume 01-03100 ASTM Volume 01-04101 ASTM Volume 01-05102 ASTM Volume 02-04103 ASTM A307 Grade A
104 ASTM A325 High Strenght Bolts For Structural Steel Joints105 ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts106 ASTM B21 Standard Specification for Naval Brass Rod, Bar and Shapes107 ASTM D1250 Standard Guide for Use of the Petroleum Measurement Tables
108 ASTM E779
109 ASTM F436 Standard Specification for Hardened Steel Washers110 AWS D1.1 Structural Welding Code-Steel111 BS 4
Structural steel sections. Specification for hot-rolled sections112 BS 302-5
113 BS 336 Specification for Fire Hose Couplings and Ancillary Equipment
Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME BPVC Section VIII-Div 1
Boiler and Pressure Vessel Code. Rules for Construction of pressure Vessels
ASME BPVC Section VIII-Div 2
Boiler and Pressure Vessel Code. Rules for Construction of pressure Vessels
Design Criteria to Prevent Core Crushing Failure in Large Diameter, Case hardened, Ball and Roller Bearings (AFBMA code)
Material Yearbooks American Society for Testing Materials Volume 01-01
Mild Steel Bolts (Bolts, studs, and threaded rod having a minimum tensile strength of 60 ksi and intended for general applications)
Standard Test Method for Determining Air Leaking Rate by Fan Pressurisation
Stranded Steel Wire Ropes - Part 5: Specification for ropes for hauling purposes
5 of 24
No Code & Standards Title
114 BS 476 Fire Tests on Building Materials and Structures 115 BS 1041 Temperature Measurement116 BS 1553-1
117 BS 1635
118 BS 1646
119 BS 1655
120 BS 1868 Steel Check Valves121 BS 1873 Steel Globe Valves122 BS 2562
Specification For Cable Boxes For Transformers and Reactors123 BS 2752 Specification for chloroprene rubber compounds124 BS 2765
125 BS 2853
126 BS 2915 Specification for Bursting discs and bursting disc devices127 BS 3463 Observation and Gauge Glasses for Pressure Vessels128 BS 3692 ISO metric precision hexagon bolts, screws and nuts129 BS 3799
130 BS 3939
131 BS 3958 Specification for bonded man-made Mineral Fibre slabs
132
BS 4190 ISO metric black hexagon bolts, screws and nuts. Specification133 BS 4211 Specification for permanently fixed ladders134 BS 4568
135 BS 4592 Industrial type flooring and stair treads136 BS 4882
137 BS 5070 Engineering Diagram Drawing Practice138 BS 5154 Bronze gate, Globes and Checks139 BS 5306 Fire Extinguishing Installation and Equipment on Premises.140 BS 5353 Steel Plug Valves141
BS 5395142 BS 5422 Method for Specifying Thermal Insulating Materials 143 BS 5500 Specification for unfired fusion welded pressure vessels144
BS 5925
Specification for Graphical Symbols General Engineering, piping Systems and Plant
Recommendation for Graphic Symbols and Abbreviations for Fire Protection Drawings
Symbolic Representation for Process Measurement Control Functions and Instrumentation
Specification for Flanged Automatic Control Valves for the Process Control Industry (Face-to-Face dimensions)
Specification for dimensions of temperature detecting elements and corresponding pockets
Specification for the design and testing of steel overhead runway beams
Specification for Steel Pipe Fittings, Screwed and Socket-Welding for the Petroleum Industry
Graphical Symbols for Electrical Power, telecommunications and Electronic Diagrams
Specification for steel conduit and fittings with metric threads of ISO form for electrical installations
Specification for bolting for flanges and pressure containing purposes
StairsCode of practice for the design of stairs with straight flights and winders
Code of Practice for Ventilation Principles and Designing for Natural Ventilation
6 of 24
No Code & Standards Title
145 BS 6121
146 BS 6169 Volumetric measurement of liquid hydrocarbons147 BS 6231
148 BS 6387
149 BS 6391
150 BS 6447
Absolute and Gauge Pressure transmitters with electrical outputs151 BS 6472
Guide to evaluation of human exposure to vibration in buildings. 152 BS 6656
153 BS 6739
154 BS 6883
155 BS 6946
156 BS 7159
157 BS 7371-6 +A1 Hot Dip Galvanising for Fasteners158 BS 7405
159 BS 7671
160 BS 7910
161 BS 8010 Pipelines162 BS 8888
163 BS EN 3-7 Portable Fire Extinguishers164 BS EN 378
165 BS EN 593 Industrial Valves – Metallic Butterfly Valves166 BS EN 779
167 BS EN 837
168 BS EN 1515 Flanges and their joints. 169 BS EN 1591
Mechanical cable glands Code of practice for selection, installation and inspection of cable glands and armour glands
Electric Cables – Single Core PVC Insulated Cables for Switchgear and Control gear Wiring
Test method for resistance to fire of cables required to maintain circuit integrity under fire conditions
Specification for Non-Percolating Lay Flat Delivery Hoses and Hose Assemblies for Fire Fighting Purposes
Assessment of inadvertent ignition of flammable atmospheres by radio frequency radiation
Code of practice for instrumentation in process control systems: installation, design and practice
Elastomer insulated cables for fixed wiring in ships and on mobile and fixed offshore units. Requirements and test methods
Specification for metal channel cable support systems for electrical installations
Design and construction of GRP Piping Systems for Individual Plants or Site
Guide to Selection and application of flowmeters for the measurement of fluid flow in closed conduits
Requirements for Electrical Installations IEE Wiring Regulations, Seventeenth Edition
Guide to methods for assessing the acceptability of flaws in metallic structures
Technical Project Specification (TPS) for Defining, Specifying and Graphically Representing Products
Specification for Refrigeration Systems and Heat Pumps – Safety and Environmental Requirements
Particulate Air Filters for General Ventilation, Determinations of the Filtration Performance
Pressure Gauges. Bourdon Tube Pressure Gauges. Dimensions, Metrology, Requirements & Testing
Flanges and their Joints. Design Rules for Gasketed Circular Flange Connections
7 of 24
No Code & Standards Title
170 BS EN 1838171 BS EN 1982 Copper Alloys Ingots and Casting172 BS EN 1993-3
173 BS EN 1991-1 Eurocode 1: Actions on Structures174 BS EN 10025 Hot rolled products of structural steels. 175 BS EN 10029
176 BS EN 10088 Stainless Steel177 BS EN 10204 Metallic Products – Types of Inspection Documents178 BS EN 10210
179 BS EN 10225
180 BS EN 10346
181 BS EN 12068 CP and External Coatings for Pipelines182 BS EN 12079
183 BS EN 12266
184 BS EN 12385 Steel wire ropes. Safety General requirements185 BS EN 12464 Lighting of work places. Outdoor work places186 BS EN 12473 General Principles of Cathodic Protection in Sea Water187 BS EN 12495 CP of Fixed Steel Offshore Structures188 BS EN 12570 Valve Operation Sizing189 BS EN 12665
190 BS EN 12696 CP of Steel in Concrete191 BS EN 12954 CP of Buried or Immersed Metallic Structure192 BS EN 13001
Cranes. General design General principles and requirements193 BS EN 13173 CP of Steel, Floating Offshore Structures194
BS EN 13414 Steel wire rope slings. Safety Slings for general lifting service195 BS EN 13480 Metallic Industrial Piping196 BS EN 13509 CP Measurement Techniques197 BS EN 13636 CP of Buried Metal Tanks & Piping198 BS EN 13771 Refrigerant Compressors199 BS EN 13823
200 BS EN 14161
Petroleum and Natural Gas - Pipeline Transportation Systems201 BS EN 14175 Fume Cupboards
Lighting applications. Emergency lighting
Eurocode 3. Design of steel structures. Towers, masts and chimneys.
Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape
Hot finished structural hollow sections of non-alloy and fine grain steels.
Weldable structural steels for fixed offshore structures. Technical delivery conditions
Continuously hot-dip coated steel flat products. Technical delivery conditions
Offshore containers and associated lifting sets. Offshore containers. Design, manufacture and marking
Industrial valves. Testing of metallic valvesPressure tests, test procedures and acceptance criteria.
Light and lighting. Basic terms and criteria for specifying lighting requirements
Reaction to fire tests for building products.Building products excluding floorings exposed to thermal attack by a single burning item
8 of 24
No Code & Standards Title
202 BS EN 14399-1
203 BS EN 14505 CP of Complex Structure204 BS EN 15112 External Cathodic protection of well casings205 BS EN 22553
206 BS EN 50172 Emergency escape lighting systems207 BS EN 50173
208 BS EN 50174 Information technology. Cabling installation. Installation209 BS EN 50262 Cable glands for electrical installations210 BS EN 50288 Instrumentation Cables211 BS EN 50563
212 BS EN 55022
213 BS EN 55024
214 BS EN 60079 Electrical Apparatus for Explosive Gas Atmospheres215 BS EN 60309 Plugs, socket-outlets and couplers for industrial purposes216 BS EN 60534 Flow Equations for Sizing Control Valves217 BS EN 60598 Luminaires. 218 BS EN 60794.1.2 Optical fibres, product specifications Test procedures219 BS EN 60896 Stationary lead-acid batteries 220 BS EN 60898
221 BS EN 61082
Preparation of documents used in electrotechnology Part 1: Rules222 BS EN 61204 Low-voltage power supplies, d.c. output223 BS EN 61543
224 BS EN 61558
225 BS EN 62034
226 BS EN ISO 1461
227 BS EN ISO 1182
Reaction to fire tests for building products.Non combustibility test228 BS EN ISO 2081
229 BS EN ISO 4126 Safety Devices for Protection against excess pressure
High-strength structural bolting assemblies for preloading General requirements
Welded, Brazed and Soldered Joints – Symbolic Representation on Drawings
Information technology. Generic cabling systems. General requirements.
External a.c.. d.c. and a.c.. a.c. power supplies. Determination of no-load power and average efficiency of active modes
Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement
Information technology equipment - Immunity characteristics - Limits and methods of measurement
Electrical accessories ± Circuit breakers for overcurrent protection for household and similar installations Circuit-breakers for a.c. operation
Residual current-operated protective devices (RCDs) for household and similar use - Electromagnetic compatibility
Safety of Power Transformers, Power Supplies, Reactor and Similar Products
Automatic test systems for battery powered emergency escape lighting
Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods
Metallic and other inorganic coatings. Electroplated coatings of zinc with supplementary treatments on iron or steel
9 of 24
No Code & Standards Title
230 BS EN ISO 5167
231 BS EN ISO 5210 Industrial Valves-Multi turn Valve Actuator Attachments232 BS EN ISO 5211 Industrial Valves. Part turn Actuator Attachment233 BS EN ISO 5801
Industrial fans-Performance testing using standardized airways234 BS EN ISO 6817
235 BS EN ISO 6976
236 BS EN ISO 7235
237 BS EN ISO 7240 Fire Detection and Alarm Systems238 BS EN ISO 7547
239 BS EN ISO 7933
240 BS EN ISO 9934 Non-destructive testing. Magnetic particle testing.241 BS EN ISO 10418
242 BS EN ISO 10434 Steel Gate Valves243 BS EN ISO 10497 Testing of valves. Fire type-testing requirements244 BS EN ISO 10715 Natural Gas, Sampling Guidelines245 BS EN ISO 11925
246 BS EN ISO 12499 Industrial fans - Mechanical safety of fans247 BS EN ISO 12944 Paints and varnishes248 BS EN ISO 13480 Metallic Industrial Piping249 BS EN ISO 13501
Fire Classification of Construction Products and Building elements.250 BS EN ISO 13628.5
251 BS EN ISO 13702
252 BS EN ISO 13703
253 BS EN ISO 14692 Petroleum and Natural Gas Industries – GPR Piping254 BS EN ISO 14713
255 BS EN ISO 15138
Measurement of Fluid Flow by means of Pressure Differential Devices in Circular Cross-Section Conduits Running Full.
Method of Conductive Fluid Flow-rate in Closed Conduits – Method Using Electromagnetic Flowmeters
Natural Gas – Calculation of Calorific Value, Density and Relative Density & Wobbe index from composition
Acoustics: Laboratory Measurement Procedures for Ducted Silencers and Air Terminal Units
Ships and Marine Technology: Air Conditioning and Ventilation of Accommodation Spaces. Design Conditions and Basis of Calculations
Ergonomics of the Thermal Environment – Analytical Determination and interpretation of Heat Stress using Calculation of the Predicted Heat Strain
Petroleum and natural Gas Industries – Offshore Production Installations – basic Surface Process Safety System
Reaction to fire tests for building products. Ignitability when subjected to direct impingement of flame.
Design and operation of subsea production systems – Subsea umbilical’s
Petroleum and natural gas industries. Control and mitigation of fires and explosions on offshore production installations. Requirements and guidelines
Petroleum and Natural Gas Industries – Design and Installation of Piping Systems on Offshore Production Platforms.
Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures. Petroleum and Natural Gas industries: Offshore Production Installations: Heating, Ventilation and Air Conditioning
10 of 24
No Code & Standards Title
256 BS EN ISO 15589 Oil & Gas Cathodic Protection of Pipelines257 BS EN ISO 15761 Gate, Globe and Check Small258 BS EN ISO 15848
259 BS EN ISO 17292
260 BS EN ISO 17640
261 BS EN ISO 17776
262 BS EN ISO 19901
263 BS EN ISO 19902
264 BS EN ISO 21457
265 BS EN ISO 61508
266 BS EN ISO 61511
267 BS ISO 76 Rolling Bearings Static Load Ratings268 BS ISO 281 Rolling Bearings Dynamic Load Ratings and Rating Life269 BS ISO 1940
270 BS ISO 4406
271 BS ISO 5168
272 BS ISO 5208 Industrial Valves – Pressure Testing of Metallic Valves273 BS ISO 10302-1
274 BS ISO 10790
275 BS ISO 11064 Ergonomic Design of Control Centres276 BS ISO 11342
277 BS ISO 13347
278 BS ISO 14695
279 BS ISO 15544
Measurement, Test and Qualification procedures for Fugitive Emissions
Metal Ball Valves for Petroleum, Petrochemical and Allied Industries
Non-destructive testing of welds. Ultrasonic testing. Techniques, testing levels, and assessment
Petroleum and natural gas industries. Offshore production installations. Guidance on tools and techniques for hazard identification and risk assessment
Petroleum and natural gas industries. Specific requirements for offshore structures.
Petroleum and natural gas industries. Fixed steel offshore structures
Petroleum, petrochemical and natural gas industries. Materials selection and corrosion control for oil and gas production systems
Functional safety of electrical/electronic/programmable electronic safety-related systems
Functional safety . Safety instrumented systems for the process industry sector
Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state
Hydraulic Fluid Power - Fluids - Method for Coding the Level of Contamination by Solid Particles
Methods of Measurement of Fluid Flow – Estimation of uncertainty of a flow-rate Measurement
Acoustic Measurement of Airborne Noise Emitted and Structure-borne Vibration by Small Air-moving Devices
Measurement of fluid flow in closed conduits — Guidance to the selection, installation and use of Coriolis meters (mass flow, density and volume flow
Mechanical vibration. Methods and criteria for the mechanical balancing of flexible rotors
Industrial Fans: Determination of Fan Sound Power Levels under Standardised Laboratory Conditions
Fans for General Purposes: Method of Measurement of Fan Vibration
Petroleum and Natural Gas Industries. Offshore Production Installations. Requirements and Guidelines for Emergency Response
11 of 24
No Code & Standards Title
280 BS ISO 15926
281 BS ISO 22899
282 BS ISO 80000 Quantities and units 283 BS PD ISO / TR 15377
284 CENELEC CLC/TR 50426
285 CENELEC CLC/TR 50427
286 CSA T568.2-1-05
287 DIN 50049 Inspection Documents for the delivery of metallic product288 DIN EN 301126-1
289 ETS/EN 300676
290 BS EN 61000
291 DTI URN 02/609 (now DECC)
292
293 EEMUA 138 Design & Installation of Online Analyser Systems294 EEMUA 144
295 EEMUA 145
296 EEMUA 158
297 EEMUA 182 Integral Block and Bleed Valves298 EEMUA 191
299 EEMUA 196
Industrial Automation Systems and Integration – Integration of Life-Cycle Data
Determination of the resistance to jet fires of passive fire protection materials
Measurement of Fluid Flow by means of Pressure Differential Devices – Guidelines for the Specification of Orifice Plates, Nozzles and Venturi Tubes beyond the scope of ISO 5167
Assessment of inadvertent initiation of bridge wire electro-explosive devices by radio-frequency radiation
Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation
Commercial Building Telecommunications Cabling Standard - Part 2: Balanced Twisted Pair Components - Addendum 1 - Transmission Performance Specifications for 4-Pair 100 Ohm Category 6A Cabling
Fixed Radio Systems. Conformance testing.Part 1: Point-to-Point equipment -Definitions, general requirements and test procedures
Electromagnetic compatibility and Radio spectrum Matters (ERM), Ground-based VHF hand-held, mobile and fixed radio transmitters, receivers and transceivers for the VHF aeronautical mobile service using amplitude modulation; Technical characteristics and methods of measurement.
Electromagnetic compatibility (EMC) – Generic standards – Immunity standard for industrial environments
Product Standards – Equipment and protective Systems Intended for use in Potentially Explosive Atmospheres – guidance Notes on the UK Regulations(ATEX)
DTI URN 05/1074 (now DECC)
Products Standards – Pressure Equipment Guidance Notes on the UK regulations (PED)
90/10 Copper Nickel Alloy piping for Offshore Applications. – Specification: Tubes Seamless and Welding
90/10 Copper Nickel Alloy Piping for Offshore Applications. – Specification: Flanges Composite and Solid
Construction Specification for Fixed Offshore Structures in the North Sea
Alarm Systems. A Guide to the Design, Management and Procurement
Valve Purchasers Guide to the European Pressure Equipment Directive
12 of 24
No Code & Standards Title
300 EEMUA 197
301 EEMUA 218
302 EIA/TIA (RS) 232 Data Communication Interface Standard303 EIA/TIA(RS) 485 Data Communication Interface Standard304 EN 10160
305 EN 302217
306 ETS/EN 300338
307 ETS/EN 300 373
308 ICAO
309 IEC 60028 International standard of resistance for copper310 IEC 60034 Rotating Electrical Machines311 IEC 60038 IEC Standard Voltages312 IEC 60044 Instrument transformers – Part 1: Current transformers313 IEC 60050 International Electrotechnical Vocabulary314 IEC 60051
315 IEC 60059 IEC standard current ratings316 IEC 60060 High voltage test techniques317 IEC 60071 Insulation co-ordination318 IEC 60072 Dimensions and output rating for rotating electrical machines
319 IEC 60073
320 IEC 60076 Power transformers321 IEC 60079
322 IEC 60085 Electrical insulation - Thermal evaluation and designation323 IEC 60092 Electrical Installations in Ships324 IEC 60096 Cables for radio frequencies325 IEC 60099 Surge arresters326 IEC 60112
Specification for the Fabrication of Non-Primary Structural Steelwork for Offshore Installations
Quality Requirements for the manufacture and Supply of Duplex Stainless Steel
Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) (replaces BS5996)
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas
ETSI Telecommunications Standard – Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobETSI Telecommunication Standard – Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for maritime mobile transmitters and receivers for use in the MF and HF bands
International Civil Aviation Organisation Aeronautical Telecommunications – Annex 10
Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts.
Basic and Safety Principles for Man-Machine Interface, Marking and Identification - Coding Principles for Indicators and Actuators
Electrical Apparatus for explosive gas atmospheres. Part 0: General Requirements
Method for determining the proof and the comparative tracking index of Solid insulating materials
13 of 24
No Code & Standards Title
327 IEC 60136 Dimensions of brushes and brush-holders for electrical machines
328 IEC 60137 Insulated bushings for alternating voltages above 1 000 V329 IEC 60145 Var-hour (reactive energy) meters330 IEC 60146331 IEC 60156
332 IEC 60158 Low Voltage Control Gear333 IEC 60169-1 AMD 1 Connectors for radio frequencies334 IEC 60183 Guide to the selection of high-voltage cables335 IEC 60189
336 IEC 60204 Safety of machinery - Electrical equipment of machines337 IEC 60211 Maximum Demand Indicators, Class 1.0338 IEC 60214 Tap-changers. 339 IEC 60215 Safety rules for radio transmitters340 IEC 60227
341 IEC 60228 Conductors of insulated cables342 IEC 60255 Electrical Relays & Measuring relays and protection equipment
343 IEC 60268 Equipment for electro-acoustic systems344 IEC 60269 Low-voltage fuses345 IEC 60270 High-voltage test techniques – Partial discharge measurements
346 IEC 60282 High-voltage fuses 347 IEC 60287 348 IEC 60304 Standard colours for insulation for low-frequency cables and wires
349 IEC 60309 Plugs,socket-outlets and couplers for industrial purposes350 IEC 60331 Fire Resisting Characteristics of Electrical Cables351 IEC 60332 Tests on Electrical and optical fibre cables under Fire Conditions
352 IEC 60364 Low Voltage electrical installations in buildings353 IEC 60398 Industrial electroheating installations - General test methods
354 IEC 60417 DB Graphical symbols for use on equipment355 IEC 60445
356 IEC 60487
357 IEC 60488 Standard digital interface for programmable instrumentation
Semiconductor converters Insulating liquids - Determination of the breakdown voltage at power frequency - Test method
Low frequency cables and wired with PVC insulation and PVC Sheath
Polyvinylchloride insulated cables of rated voltages up to and including 450/750 V
Electric cables – Calculation of the current rating
Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
Methods of measurement for equipment used in terrestrial radio-relay systems.
14 of 24
No Code & Standards Title
358 IEC 60502
359 IEC 60519 Safety in electroheating installations360 IEC 60529 Degrees of protection provided by enclosures (IP Code)361 IEC 60533
362 IEC 60534 Industrial Process Control Valves363 IEC 60584 Thermocouples364 IEC 60598 Luminaires365 IEC 60617 DB SNAPSHOT Graphical symbols for diagrams-DATABASE SNAPSHOT366 IEC 60622
367 IEC 60644
368 IEC 60688
369 IEC 60695 Fire hazard testing370 IEC 60706371 IEC 60708
372 IEC 60751
373 IEC 60754
374 IEC 60793.2 Optical fibres, product specifications375 IEC 60794 Optical fibre cables376 IEC 60800
377 IEC 60811
378 IEC 60851 Winding wires - Test methods379 IEC 60885 Electrical test methods for electric cables 380 IEC 60898
381 IEC 60909 Short-circuit currents in three-phase a.c. systems382 IEC 60947 Low-voltage switchgear and controlgear383 IEC 60950384 IEC 61000 Electromagnetic Compatibility (EMC).385 IEC 61008
386 IEC 61009
Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV)
Electrical and electronic installations in ships –Electromagnetic compatibility
Secondary cells and batteries containing alkaline or other non-acid electrolytes - Sealed nickel-cadmium prismatic rechargeable single cells
Specification for high-voltage fuse-links for motor circuit applications
Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
Maintainability of equipment Low frequency cables with polyolefin insulation and moisture barrier polyolefin sheath
Industrial platinum resistance thermometers and platinum temperature sensors
Test on gases evolved during combustion of materials from cables –
Heating cables with a rated voltage of 300/500 V for comfort heating and prevention of ice formation
Electric and optical fibre cables - Test methods for non-metallic materials
Electrical accessories –Circuit-breakers for overcurrent protection for household and similar installations
Information technology equipment
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs)
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs)
15 of 24
No Code & Standards Title
387 IEC 61034
388 IEC 61069
389 IEC 61082 Preparation of documents used in electrotechnology390 IEC 61131 Programmable Controllers391 IEC 61140
392 IEC 61230
393 IEC 61293
394 IEC 61326
395 IEC 61363
396 IEC 61378 Converter transformers397 IEC 61439 Low-voltage switchgear and controlgear assemblies398 IEC 61508
399 IEC 61511
400 IEC 61520 Thermowells401 IEC 61537 Cable management - Cable tray systems and cable ladder systems
402 IEC 61554
403 IEC 61558
404 IEC 61672 Electro acoustics - Sound level meters405 IEC 61800 Adjustable speed electrical power drive systems 406 IEC 61850 Communication networks and systems for power utility automation
407 IEC 61869 Instrument transformers 408 IEC 61892 Mobile and fixed offshore units -Electrical installations409 IEC 61914 Cable cleats for electrical installations410 IEC 61935
411 IEC 62026
412 IEC 62040 Uninterruptible power systems (UPS)413 IEC 62052
414 IEC 62053 Electricity metering equipment (a.c.) - Particular requirements
Measurement of smoke density of cables burning under defined conditions
Industrial Process Measurement and Control – Evaluation of System Properties for the Purpose of System Assessment
Protection against electric shock – Common aspects for installation and equipment
Live working - Portable equipment for earthing or earthing and short-circuiting
Marking of electrical equipment with ratings related to electrical supply - Safety requirements
Electrical Equipment for Measurement, Control & Laboratory Use
Electrical installations of ships and mobile and fixed offshore units - Part 1: Procedures for calculating short-circuit currents in three-phase a.c.
Functional Safety of Electrical/Electronic/Programmable Electronic Safety Related Systems
Functional Safety – Safety Instrumented Systems for the Process industry Sector
Panel mounted equipment - Electrical measuring instruments - Dimensions for panel mounting
Safety of power transformers, power supplies, reactors and similar products. Part 1: General requirements and tests
Specification for the testing of balanced and coaxial information technology cabling.
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs)
Electricity metering equipment (AC) - General requirements, tests and test conditions
16 of 24
No Code & Standards Title
415 IEC 62259
416 IEC 62262
417 IEC 62271 High-voltage switchgear and controlgear - ALL PARTS418 IEC 62305 Protection against lightning419 IEC 62395
420 IEC 62402 Obsolescence management - Application guide421 IEC 62444 Cable glands for electrical installations422 IEC CISPR 16
423 IEC CISPR 61000 Electromagnetic Compatibility (EMC) 424 IEC EN 60936
425 IEC/TR 60092-370
426 IEC/TR 60616 Terminal and tapping markings for power transformer427 IEC/TR 60894
428 IEC/TR 61439 Low-voltage switchgear and controlgear assemblies 429 IEC/TR 61641
430 IEC /TR 61831 Analyser Systems431432 IEC/TR 61869-103
433 IEC Publication 244-2B Measurement methods applicable to radio transmitters
434 IEC Publication 315
435 IEE
436 IEEE 519
437 IEEE 730 Standard for Software Quality Assurance Plans (ANSI)438 IEEE 802.11 Wireless LAN Medium Access Control439 IEEE 802.1D Rapid reconfiguration of spanning tree recommendation440 IEEE 802.3 CSMA/CD (Ethernet)441 IEEE 828
Standard for Software Configuration Management Plans (ANSI)442 IEEE 829 Standard for Software Test Documentation443 IEEE 830 Guide for Software Requirements Specifications (ANSI)
Secondary cells and batteries containing alkaline or other non-acid electrolytes - Nickel-cadmium prismatic secondary single cells with partial gas recombination
Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
Electrical resistance trace heating systems for industrial and commercial applications
Specification for radio disturbance and immunity measuring apparatus and methods
Maritime navigation and radio communication equipment and systems
Shipboard telecommunications cables and radio frequency cables. General instrumentation, control and communication cables
Guide for test procedure for the measurement of loss tangent of coils and bars for machine windings
Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault
Instrument transformers - The use of instrument transformers for power quality measurement
Measurement methods for radio receivers of different classes of emission
Recommendations For The Electrical And Electronic Equipment Of Mobile And Fixed Offshore Installations
Recommended Practices and Requirements for Harmonic Control in Electrical Power Systems
17 of 24
No Code & Standards Title
444 IEEE 1008 Standard for Software Unit Testing (ANSI)445 IEEE 1012
Standard for Software Verification and Validation Plans (ANSI)446 IEEE 1016
Recommended Practice for Software Design Descriptions447 ISA 5.1 Instrumentation Symbols and Identification448 ISA 7.0.1 Quality Standard for Instrument Air449 ISA 51.1 Process Instrumentation Terminology450 ISA 75.01 Flow Equations for Sizing Control Valves451 ISA 75.03
452 ISA 75.07
453 ISA 75.08
454 ISA 75.16 Control Valve Cavitation455 ISA TR 99 All Parts Manufacturing and Control Systems Security456 ISO 834 Fire-resistance tests-Elements of Building Construction457 ISO 14313 Valves- Pipeline458 ISO/IEC Directives, Part 2 Rules for the structure and drafting of International Standards
459 ITU-R BT.656
460 ITU-R BT.796
461 ITU-R F.752 Diversity techniques for point-to-point fixed wireless systems
462 ITU-R M.478
463 ITU-R M.1225 Guidelines for evaluation of radio transmission464 ITU-R P.368
465 ITU-R P.525 Calculation of free-space attenuation466 ITU-R P.528
467 ITU-R P.530
468 ITU-R P.1410 Propagation data and prediction methods469 ITU-R SA.363
470 ITU-T G.114 Guidance on one-way delay for Voice over IP471 ITU-T G.131 Talker echo and its control472 ITU-T G.652 Single mode fibres (1300 nm)473 ITU-T G.653 Single mode fibres (1550 nm)474 ITU-T G.654 Single mode fibres (1530 - 1625 nm)
Face-to-Face Dimensions for Flanged Globe-Style Control Valves Bodies: ANSI Classes, 125, 150, 250, 300, and 600.
Laboratory Measurement of Aerodynamic Noise Generated by Control Valves
Face to Face Dimensions for Integral Flanged Globe Style Control Valve Bodies (ANSI Classes 125, 150, 300, & 600)
Interface for digital component video signals in 525-line and 625-line television systems
Parameters for enhanced compatible coding systems based on 625-line pal and secam television systems
Technical characteristics of equipment and principles governing the allocation of frequency channels between 25 and 3000 MHz for the FM Land Mobile service
Ground-wave propagation curves for frequencies between 10 kHz and 30 MHz
Propagation curves for aeronautical mobile and radio navigation services using the VHF, UHF and SHF bands
Propagation data and prediction methods required for the design of terrestrial line-of-sight systems.
Space operation systems. Frequencies, bandwidths and protection criteria
18 of 24
No Code & Standards Title
475 ITU-T G.655 Single mode fibres (1530 - 1565 nm)476 ITU-T G.707 SDH network node interface477 ITU-T G.708 SDH network node interface478 ITU-T G.711 Pulse code modulation for Voice frequencies479 ITU-T G.729
480 ITU-T G.780 SDH vocabulary481 ITU-T G.783 SDH equipment functional blocks482 ITU-T G.784 SDH Management.483 ITU-T G.803
484 ITU-T G.805 Generic functional architecture of transport networks485 ITU-T G.813 Timing characteristics of SDH equipment slave clocks (SEC)
486 ITU-T G.823
487 ITU-T G.825
488 ITU-T G.826
489 ITU-T G.828
490 ITU-T G.841
491 ITU-T G.842 Interworking of SDH protection architectures492 ITU-T G.872 Architecture of optical transport networks493 ITU-T G.911
494 ITU-T G.957
495 ITU-T G.977 Repeatered optical submarine systems496 ITU-T H.323 Packet-Based Multimedia Communications Systems497 ITU-T K.11 Surge protectors and recommendation for telecom equipment
498 ITU-T K.18
499 ITU-T L.1
500 ITU-T M.2100 Commissioning and maintenance (measurement procedures)
501 ITU-T M.2110 SDH and PDH commissioning (measurement procedures)
502 ITU-T M.2120 Fault detection (PDH and SDH)503 ITU-T M.3010 Principles for a Telecommunication Management Network
Coding of speech at 8kbit/s using conjugate- structure algebraic code excited linear prediction
Architecture of transport networks based on the synchronous digital hierarchy (SDH)
The control of jitter and wander within digital networks which are based on the 2048 kbit/s hierarchy
The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH)
End-to-end error performance parameters and objectives for international, constant bit-rate digital paths and connections
Error performance parameters and objectives for international, constant bit rate synchronous digital paths
Types and characteristics of SDH network protection architectures
Parameters and calculation methodologies for reliability and availability of fibre optic systems
Optical interfaces for equipments and systems relating to the synchronous digital hierarchy
Calculation of voltage induced into telecommunication lines from radio station broadcasts and methods of reducing interference
Construction, installation and protection of telecommunication cables in public networks
19 of 24
No Code & Standards Title
504 ITU-T M.3100 Generic Network Information Model505 ITU-T RECOMMENDATI ON T.
506 ITU-T RECOMMENDATI ON T.
507 ITU-T RECOMMENDATI ON T.
508 ITU-T X.209 Encoding rules specification of Basic Encoding Rules509 ITU-T X.690 Encoding rules specification of Basic Encoding Rules510 MSS SP6
511 MSS SP25
Standard Marking System for Valves, Fittings, Flanges and Unions512 MSS SP44 Steel Pipe Line Flanges513 MSS SP75 Fittings High Yield Steel514 MSS SP80 Bronze Gate, Globe, Angle and Check Valves515 MSS SP97 Branch Outlet Fittings516 NACE MR0175/ISO 15156
517 NFPA 1518 NFPA 10 Standard for Portable Fire Extinguishers519 NFPA 11 Standard for Low, Medium and High Expansion Foam520 NFPA 11A
STANDARD FOR MEDIUM AND HIGH EXPANSION FOAM SYSTEMS521 NFPA 12 Standard on Carbon Dioxide Extinguishing Systems522 NFPA 13 Installation of Sprinkler Systems523 NFPA 14
524 NFPA 15 Standard for Water Spray Fixed Systems for Fire Protection525 NFPA 16
526 NFPA 17 Standard for Dry Chemical Extinguishing Systems527 NFPA 17A Standard for Wet Chemical Extinguishing Systems528 NFPA 20
529 NFPA 30 FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE530 NFPA 72 National Fire Alarm and Signalling Code531 NFPA 75
532 NFPA 76
533 NFPA 90A
534 NFPA 96
535 NFPA 101
for document facsimile transmission in the general switched telephone network
Procedures for the transfer of facsimile date via store-and forward on the Internet
Procedures for real-time Group 3 facsimile communication over IP networks
Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
Petroleum and natural gas industries. Materials for use in H2S-containing.Environments in oil and gas production
FIRE CODE
STANDARD FOR THE INSTALLATION OF STANDPIPE AND HOSE SYSTEMS
Standard for Installation of Foam-Water Sprinkler and Foam-Water Spray Systems
Standard for the Installation of Stationary Fire Pumps for Fire Protection
STANDARD FOR THE FIRE PROTECTION OF INFORMATION TECHNOLOGY EQUIPMENT
STANDARD FOR THE FIRE PROTECTION OF TELECOMMUNICATIONS FACILITIESStandard for the Installation of Air-Conditioning and Ventilating Systems
Standard for Ventilation Control and Fire protection of Commercial Cooking Operations
LIFE SAFETY CODE
20 of 24
No Code & Standards Title
536 NFPA 111537 NFPA 496
538 NFPA 750 Standard for Water Mist Fire protection Systems539 NFPA 2001 Standard for Clean Agent Fire Extinguishing Systems
Offshore Standards -DNVDNV-OS-A101DNV-OS-A201DNV-OS-B101DNV-OS-C101DNV-OS-C102DNV-OS-C103DNV-OS-C104DNV-OS-C105DNV-OS-C106DNV-OS-C201DNV-OS-C301DNV-OS-C401DNV-OS-C501DNV-OS-C502DNV-OS-C503DNV-OS-D101DNV-OS-D201DNV-OS-D202DNV-OS-D203DNV-OS-D301DNV-OS-E101DNV-OS-E201DNV-OS-E301DNV-OS-E302DNV-OS-E303DNV-OS-E304DNV-OS-E401DNV-OS-E402DNV-OS-E403DNV-OS-E406DNV-OS-E407DNV-OS-F101DNV-OS-F201DNV-OS-H101DNV-OS-H102DNV-OS-H201DNV-OS-H203DNV-OS-H204DNV-OS-J101
STANDARD ON STORED ELECTRICAL ENERGY EMERGENCY Standard for Purged and Pressurised Enclosures for Electrical Equipment
Safety Principles and ArrangementsWinterization for Cold Climate Operations (Tentative)Metallic MaterialsDesign of Offshore Steel Structures, General (LRFD Method)Structural Design of Offshore ShipsStructural Design of Column Stabilised Units (LRFD Method)Structural Design of Self-Elevating Units (LRFD Method)Structural Design of TLPs (LRFD Method)Structural Design of Deep Draught Floating Units (LRFD Method)Structural Design of Offshore Units (WSD Method)Stability and Watertight IntegrityFabrication and Testing of Offshore StructuresComposite ComponentsOffshore Concrete StructuresConcrete LNG Terminal Structures and Containment SystemsMarine and Machinery Systems and EquipmentElectrical InstallationsAutomation, Safety, and Telecommunication SystemsIntegrated Software Dependent System (ISDS)Fire ProtectionDrilling PlantOil and Gas Processing SystemsPosition MooringOffshore Mooring ChainOffshore Fibre RopesOffshore Mooring Steel Wire RopesHelicopter DecksOffshore Standard for Diving SystemsOffshore Loading BuoysDesign of Free Fall LifeboatsUnderwater Deployment and Recovery SystemsSubmarine Pipeline SystemsDynamic RisersMarine Operations, GeneralMarine Operations, Design and FabricationLoad Transfer OperationsTransit and Positioning of Offshore UnitsOffshore Installation Operations (VMO Standard Part 2-4)Design of Offshore Wind Turbine Structures
21 of 24
No Code & Standards Title
DNV-OS-J103DNV-OS-J201DNV-OS-J301
Recommended PracticesDNV-RP-A201DNV-RP-A203DNV-RP-A204DNV-RP-A205DNV-RP-B101DNV-RP-B401DNV-RP-C101DNV-RP-C102DNV-RP-C103DNV-RP-C104DNV-RP-C201DNV-RP-C202DNV-RP-C203DNV-RP-C204DNV-RP-C205DNV-RP-C206DNV-RP-C207DNV-RP-C208DNV-RP-C301DNV-RP-C302DNV-RP-D101DNV-RP-D102DNV-RP-D201DNV-RP-D202DNV-RP-E101DNV-RP-E102DNV-RP-E301DNV-RP-E302DNV-RP-E303DNV-RP-E304DNV-RP-E306DNV-RP-E307DNV-RP-E401DNV-RP-E402DNV-RP-E403DNV-RP-F101DNV-RP-F102DNV-RP-F103DNV-RP-F105DNV-RP-F106DNV-RP-F107
Design of Floating Wind Turbine StructuresOffshore Substations for Wind FarmsWind Turbine Installation Units
Plan Approval Documentation Types – DefinitionsTechnology QualificationQuality Survey Plan (QSP) for Offshore Class New-building SurveysOffshore Classification Projects - Testing and CommissioningCorrosion Protection of Floating Production and Storage UnitsCathodic Protection DesignAllowable Thickness Diminution for Hull Structure of Offshore ShipsStructural Design of Offshore ShipsColumn-Stabilised UnitsSelf-elevating UnitsBuckling Strength of Plated StructuresBuckling Strength of ShellsFatigue Design of Offshore Steel StructuresDesign against Accidental LoadsEnvironmental Conditions and Environmental LoadsFatigue Methodology of Offshore ShipsStatistical Representation of Soil DataDetermination of Structural Capacity by Non-linear FE analysis MethodsDesign, Fabrication, Operation and Qualification of Bonded Repair of Steel StructuresRisk Based Corrosion ManagementStructural Analysis of Piping SystemsFailure Mode and Effect Analysis (FMEA) of Redundant SystemsIntegrated Software Dependent SystemsWitnessing of Low Sulphur Fuel Changeover and OperationsRecertification of Well Control Equipment for the Norwegian Continental ShelfRecertification of Blowout Preventers and Well Control Equipment for the US Outer Continental ShelfDesign and Installation of Fluke AnchorsDesign And Installation of Plate Anchors in ClayGeotechnical Design and Installation of Suction Anchors in ClayDamage Assessment of Fibre Ropes for Offshore MooringDynamic Positioning Vessel Design Philosophy GuidelinesDynamic Positioning Systems - Operation GuidanceSurvey of Diving SystemsNaval Rescue SubmersiblesHyperbaric Evacuation SystemsCorroded PipelinesPipeline Field Joint Coating and Field Repair of Linepipe CoatingCathodic Protection of Submarine Pipelines by Galvanic AnodesFree Spanning PipelinesFactory Applied External Pipeline Coatings for Corrosion ControlRisk Assessment of Pipeline Protection
22 of 24
No Code & Standards Title
DNV-RP-F108DNV-RP-F109DNV-RP-F110DNV-RP-F111DNV-RP-F112DNV-RP-F113DNV-RP-F116DNV-RP-F118DNV-RP-F201DNV-RP-F202DNV-RP-F203DNV-RP-F204DNV-RP-F205DNV-RP-F206DNV-RP-F301DNV-RP-F302DNV-RP-F401DNV-RP-G101DNV-RP-G103DNV-RP-H101DNV-RP-H102DNV-RP-H103DNV-RP-H104DNV-RP-J101DNV-RP-J201DNV-RP-J202DNV-RP-J203DNV-RP-J301DNV-RP-O401DNV-RP-O501DNV-RP-U301
Fracture Control for Pipeline Installation Methods Introducing Cyclic Plastic StrainOn-Bottom Stability Design of Submarine PipelinesGlobal Buckling of Submarine Pipelines Structural Design due to High Temperature/High PressureInterference Between Trawl Gear and PipelinesDesign of Duplex Stainless Steel Subsea Equipment Exposed to Cathodic ProtectionPipeline Subsea RepairIntegrity Management of Submarine Pipeline SystemsPipe Girth Weld AUT System Qualification and Project Specific Procedure ValidationDesign of Titanium RisersComposite RisersRiser InterferenceRiser FatigueGlobal Performance Analysis of Deepwater Floating StructuresRiser Integrity ManagementSubsea Separator Structural DesignSelection and use of Subsea Leak Detection SystemsElectrical Power Cables in Subsea ApplicationsRisk Based Inspection of Offshore Topsides Static Mechanical EquipmentNon-Intrusive InspectionRisk Management in Marine and Subsea OperationsMarine Operations during Removal of Offshore InstallationsModelling and Analysis of Marine OperationsBallast, Stability, and Watertight Integrity - Planning and Operating GuidanceUse of Remote Sensing for Wind Energy AssessmentsQualification Procedures for CO2 Capture TechnologyDesign and Operation of CO2 PipelinesGeological Storage of Carbon DioxideSubsea Power Cables in Shallow Water Renewable Energy ApplicationsSafety and Reliability of Subsea SystemsErosive Wear in Piping SystemsRisk Management of Shale Gas Developments and Ope
23 of 24
Determination of Structural Capacity by Non-linear FE analysis MethodsDesign, Fabrication, Operation and Qualification of Bonded Repair of Steel Structures
Recertification of Well Control Equipment for the Norwegian Continental ShelfRecertification of Blowout Preventers and Well Control Equipment for the US Outer Continental Shelf
24 of 24
Fracture Control for Pipeline Installation Methods Introducing Cyclic Plastic Strain
Global Buckling of Submarine Pipelines Structural Design due to High Temperature/High Pressure
Design of Duplex Stainless Steel Subsea Equipment Exposed to Cathodic Protection
Pipe Girth Weld AUT System Qualification and Project Specific Procedure Validation
Risk Based Inspection of Offshore Topsides Static Mechanical Equipment
Ballast, Stability, and Watertight Integrity - Planning and Operating Guidance
Subsea Power Cables in Shallow Water Renewable Energy Applications