Sheet1CODE & STANDARDS LISTNoCode & StandardsTitle1AISCCAmerican Institute of Steel Construction2ANSI / FCI 70.2Control Valve Seat Leakage3ANSI B.18.22.1Plain Washer4ANSI B1.1 (UNC)/ ANSI B.18.2.2 Bolt and Nut Thread (Unied Coarse Thread)5API 2BSpecification for the Fabrication of Structural Steel Pipe6API 2COffshore Cranes7API 2WSpecification for Steel Plates for Offshore Structures, Produced by Thermo-Mechanical Control Processing (TMCP)8API 2YSpecification for Steel Plates, Quenched-and-Tempered, for Offshore Structures9API 5LSeamless and Welded Steel Line Pipe10API 6ASpecification for Wellhead and Christmas Tree Equipment, Twentieth Edition (ISO 10423:2009 Modification), Includes Errata (through November 2013), Addenda 1(Nov 2011), 2 (Nov 2012), 3 (March 2013)11API 6AFTechnical Report on Capabilities of API Flanges under Combinations of Load12API 6DSpecification for Pipeline Valves13API 7B-11CSpecification for Internal-Combustion Reciprocating Engines for Oil Field Service14API 12JSpecification for Oil and Gas Separators15API 14CAnalysis, Design, Installation, and Testing of Basic Surface Safety Systems for Offshore Production Platforms16API 14ERecommended Practice for Design and Installation of Offshore Products Platform Piping Systems17API 14GRecommended Practice for Fire Prevention and Control on Fixed Open-type Offshore Production Platforms, Fourth Edition18API 14JRecommended Practice for Design and Hazards Analysis for Offshore Production Facilities19API 15HRSpecification for High Pressure Fiberglass Line Pipe, Includes Addendum/Errata 1 and Errata 2 (2008)20API 16CAPI 16C21API 75Recommended Practice for Development of a Safety and Environmental Management Program for Offshore Operations and Facilities22API 500Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Division I and Division 223API 505Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Zone 0, and Zone 224API 520Sizing, Selection, and Installation of Pressure-relieving Devices in Refineries, Part I - Sizing and Selection, Eighth Edition25API 521Guide for Pressure-relieving and Depressuring Systems: Petroleum petrochemical and natural gas industries-Pressure relieving and depressuring systems, Fifth Edition (Includes 2008 Addendum)26API 526Flanged Steel Pressure Relief Valves27API 534Heat Recovery Steam Generators28API 594Check Valves Flanged and Water29API 598Valve Inspection and Testing30API 599Plug Valves31API 607Fire test for Quarter Turn Valves32API 608Metal Ball Valves Flanged and Welded Ends33API 609Butterfly Valves34API 610Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries35API 612API Standard 612, Petroleum, Petrochemical and Natural Gas Industries - Steam Turbines - Special-purpose Applications36API 615Valve Selection Guide37API 616Gas Turbines for the Petroleum, Chemical, and Gas Industry Services38API 617Axial and Centrifugal Compressors and Expander-compressors for Petroleum, Chemical and Gas Industry Services39API 618Reciprocating Compressors for Petroleum, Chemical, and Gas Industry Services40API 619Rotary-Type Positive-Displacement Compressors for Petroleum, Petrochemical, and Natural Gas Industries41API 670Machinery Protection Systems42API 674Positive Displacement Pumps - Reciprocating43API 675Positive Displacement Pumps-Controlled Volume44API 676Positive Displacement Pumps-Rotary45API 677General Purpose Gear Units for Petroleum, Chemical and Gas Industry Services46API 682Pumps-Shaft Sealing Systems for Centrifugal and Rotary Pumps47API 750Management of Process Hazards48API 752Management of Hazards Associated With Location of Process Plant Buildings, CMA Manager's Guide49API 754Process Safety Performance Indicators for the Refining and Petrochemical Industries50API 2000Venting Atmospheric and Low-pressure Storage Tanks, Sixth Edition (Identical Adoption of ISO 28300:2008)51API 2030Application of Fixed water Spray Systems for Fire Protection in Petroleum and Petrochemical Industries52API 2218Fireproofing Practices in Petroleum & Petrochemical Processing Plants53API RP 2FPS Recommended Practice for Planning, Designing, and Construction Floating Production Systems54API RP 2SK Recommended Practice for Design and Analysis of Station keeping Systems for Floating Structures55API RP 2A WSDRecommended Practice for Planning, Designing and Constructing Fixed Offshore PlatformsWorking Stress Design56API RP 550 Installation of Refinery Instruments and Control Systems57API RP 551Process Measurement Instrumentation58API RP 554 Process Control Systems. 59API RP 555Process Analyzers60API RP 576Inspection of Pressure Relieving Devices61API RP 2201Safe Hot tapping Practices in the Petroleum and Petrochemical Industries62API SPEC 2MT1Specification for Carbon Manganese Steel Plate with Improved Toughness for Offshore Structures63API SPEC 2MT2Rolled Shapes with Improved Notch Toughness64API SPEC 2HSpecification for Carbon Manganese Steel Plate for Offshore Platform Tubular Joints, Ninth Edition65API SPEC 6FASpecification for Fire test for Valves66API STD 527Seat Tightness of Pressure Relief Valves with Metal to Metal Seats67API STD 600Bolted Bonnet Steel Gate Valves for Petroleum & Natural Gas Industries68API STD 602Compact Steel Gate Valves, Flanged, Threaded, Welding and Extended-Body Ends69ASCE 41088Design of Blast-Resistant Buildings in Petrochemical Facilities70ASME B1.1Unified Inch Screw Threads71ASME B1.20.1Pipe Thread, General Purpose (Inch)72ASME B16.1Cast Iron Pipe Flanges and Flanged Fittings73ASME B16.5Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard74ASME B16.9Butt Welding Pipe Fittings75ASME B16.10Face-to-Face and End-to-End Dimensions of Valves76ASME B16.11Fittings Socket Weld and Threaded77ASME B16.20Metallic Gaskets for Pipe Flanges Ring Joint, Spiral Wound and jacketed78ASME B16.21Gaskets Non-Metallic79ASME B16.25Buttwelding Ends80ASME B16.34Valves Flanged, Threaded and Welding Ends81ASME B16.36Orifice Flanges82ASME B16.47Flanges Large83ASME B16.48Steel Line Blanks84ASME B31.3Process Piping85ASME B31.4Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids86ASME B31.8Gas Transmission and Distribution Piping Systems87ASME B36.10Dimensions and Weights of Steel Pipes88ASME B36.19Dimensions of Stainless Steel Pipe89ASME B46.1Surface Texture (Roughness, Waviness and Lay)90ASME BPVC Section IIMaterial Specifications (Part A, B and C)91ASME BPVC Section IIProperties (Part D)92ASME BPVC Section IIProperties, Metric (Part IID M)93ASME BPVC Section VIII-Div 1Boiler and Pressure Vessel Code. Rules for Construction of pressure Vessels94ASME BPVC Section VIII-Div 2Boiler and Pressure Vessel Code. Rules for Construction of pressure Vessels95ASME BPVC Section IXWelding and Brazing Qualifications96ASME PTC 19.3 TWThermowell Performance Test Codes97ASME 77 DE 39Design Criteria to Prevent Core Crushing Failure in Large Diameter, Case hardened, Ball and Roller Bearings (AFBMA code)98ASTMMaterial Yearbooks American Society for Testing Materials Volume 01-0199ASTMVolume 01-03100ASTMVolume 01-04101ASTMVolume 01-05102ASTMVolume 02-04103ASTM A307 Grade AMild Steel Bolts (Bolts, studs, and threaded rod having a minimum tensile strength of 60 ksi and intended for general applications)104ASTM A325High Strenght Bolts For Structural Steel Joints105ASTM A563Standard Specification for Carbon and Alloy Steel Nuts106ASTM B21 Standard Specification for Naval Brass Rod, Bar and Shapes107ASTM D1250Standard Guide for Use of the Petroleum Measurement Tables108ASTM E779Standard Test Method for Determining Air Leaking Rate by Fan Pressurisation109ASTM F436Standard Specification for Hardened Steel Washers110AWS D1.1Structural Welding Code-Steel111BS 4Structural steel sections. Specification for hot-rolled sections112BS 302-5Stranded Steel Wire Ropes - Part 5: Specification for ropes for hauling purposes113BS 336Specification for Fire Hose Couplings and Ancillary Equipment114BS 476 Fire Tests on Building Materials and Structures 115BS 1041 Temperature Measurement116BS 1553-1Specification for Graphical Symbols General Engineering, piping Systems and Plant117BS 1635Recommendation for Graphic Symbols and Abbreviations for Fire Protection Drawings118BS 1646Symbolic Representation for Process Measurement Control Functions and Instrumentation119BS 1655Specification for Flanged Automatic Control Valves for the Process Control Industry (Face-to-Face dimensions)120BS 1868Steel Check Valves121BS 1873Steel Globe Valves122BS 2562Specification For Cable Boxes For Transformers and Reactors123BS 2752Specification for chloroprene rubber compounds124BS 2765Specification for dimensions of temperature detecting elements and corresponding pockets125BS 2853Specification for the design and testing of steel overhead runway beams126BS 2915Specification for Bursting discs and bursting disc devices127BS 3463Observation and Gauge Glasses for Pressure Vessels128BS 3692ISO metric precision hexagon bolts, screws and nuts129BS 3799Specification for Steel Pipe Fittings, Screwed and Socket-Welding for the Petroleum Industry130BS 3939Graphical Symbols for Electrical Power, telecommunications and Electronic Diagrams131BS 3958Specification for bonded man-made Mineral Fibre slabs132BS 4190ISO metric black hexagon bolts, screws and nuts. Specification133BS 4211 Specification for permanently fixed ladders134BS 4568Specification for steel conduit and fittings with metric threads of ISO form for electrical installations135BS 4592Industrial type flooring and stair treads136BS 4882Specification for bolting for flanges and pressure containing purposes137BS 5070Engineering Diagram Drawing Practice138BS 5154Bronze gate, Globes and Checks139BS 5306Fire Extinguishing Installation and Equipment on Premises.140BS 5353Steel Plug Valves141BS 5395StairsCode of practice for the design of stairs with straight flights and winders142BS 5422Method for Specifying Thermal Insulating Materials 143BS 5500Specification for unfired fusion welded pressure vessels144BS 5925Code of Practice for Ventilation Principles and Designing for Natural Ventilation145BS 6121Mechanical cable glands Code of practice for selection, installation and inspection of cable glands and armour glands146BS 6169Volumetric measurement of liquid hydrocarbons147BS 6231Electric Cables Single Core PVC Insulated Cables for Switchgear and Control gear Wiring148BS 6387Test method for resistance to fire of cables required to maintain circuit integrity under fire conditions149BS 6391Specification for Non-Percolating Lay Flat Delivery Hoses and Hose Assemblies for Fire Fighting Purposes150BS 6447Absolute and Gauge Pressure transmitters with electrical outputs151BS 6472Guide to evaluation of human exposure to vibration in buildings. 152BS 6656 Assessment of inadvertent ignition of flammable atmospheres by radio frequency radiation153BS 6739Code of practice for instrumentation in process control systems: installation, design and practice154BS 6883Elastomer insulated cables for fixed wiring in ships and on mobile and fixed offshore units. Requirements and test methods155BS 6946Specification for metal channel cable support systems for electrical installations156BS 7159Design and construction of GRP Piping Systems for Individual Plants or Site157BS 7371-6 +A1Hot Dip Galvanising for Fasteners158BS 7405Guide to Selection and application of flowmeters for the measurement of fluid flow in closed conduits159BS 7671Requirements for Electrical Installations IEE Wiring Regulations, Seventeenth Edition160BS 7910Guide to methods for assessing the acceptability of flaws in metallic structures161BS 8010Pipelines162BS 8888Technical Project Specification (TPS) for Defining, Specifying and Graphically Representing Products163BS EN 3-7 Portable Fire Extinguishers164BS EN 378Specification for Refrigeration Systems and Heat Pumps Safety and Environmental Requirements165BS EN 593Industrial Valves Metallic Butterfly Valves166BS EN 779Particulate Air Filters for General Ventilation, Determinations of the Filtration Performance167BS EN 837Pressure Gauges. Bourdon Tube Pressure Gauges. Dimensions, Metrology, Requirements & Testing168BS EN 1515Flanges and their joints. 169BS EN 1591Flanges and their Joints. Design Rules for Gasketed Circular Flange Connections170BS EN 1838Lighting applications. Emergency lighting171BS EN 1982Copper Alloys Ingots and Casting172BS EN 1993-3Eurocode 3. Design of steel structures. Towers, masts and chimneys. 173BS EN 1991-1Eurocode 1: Actions on Structures174BS EN 10025Hot rolled products of structural steels. 175BS EN 10029Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape176BS EN 10088Stainless Steel177BS EN 10204Metallic Products Types of Inspection Documents178BS EN 10210Hot finished structural hollow sections of non-alloy and fine grain steels. 179BS EN 10225Weldable structural steels for fixed offshore structures. Technical delivery conditions180BS EN 10346Continuously hot-dip coated steel flat products. Technical delivery conditions181BS EN 12068CP and External Coatings for Pipelines182BS EN 12079Offshore containers and associated lifting sets. Offshore containers. Design, manufacture and marking183BS EN 12266Industrial valves. Testing of metallic valvesPressure tests, test procedures and acceptance criteria. 184BS EN 12385Steel wire ropes. Safety General requirements185BS EN 12464Lighting of work places. Outdoor work places186BS EN 12473General Principles of Cathodic Protection in Sea Water187BS EN 12495CP of Fixed Steel Offshore Structures188BS EN 12570Valve Operation Sizing189BS EN 12665Light and lighting. Basic terms and criteria for specifying lighting requirements190BS EN 12696CP of Steel in Concrete191BS EN 12954CP of Buried or Immersed Metallic Structure192BS EN 13001Cranes. General design General principles and requirements193BS EN 13173CP of Steel, Floating Offshore Structures194BS EN 13414Steel wire rope slings. Safety Slings for general lifting service195BS EN 13480Metallic Industrial Piping196BS EN 13509CP Measurement Techniques197BS EN 13636CP of Buried Metal Tanks & Piping198BS EN 13771Refrigerant Compressors199BS EN 13823Reaction to fire tests for building products.Building products excluding floorings exposed to thermal attack by a single burning item200BS EN 14161Petroleum and Natural Gas - Pipeline Transportation Systems201BS EN 14175Fume Cupboards202BS EN 14399-1High-strength structural bolting assemblies for preloading General requirements203BS EN 14505CP of Complex Structure204BS EN 15112External Cathodic protection of well casings205BS EN 22553Welded, Brazed and Soldered Joints Symbolic Representation on Drawings206BS EN 50172Emergency escape lighting systems207BS EN 50173 Information technology. Generic cabling systems. General requirements.208BS EN 50174 Information technology. Cabling installation. Installation209BS EN 50262Cable glands for electrical installations210BS EN 50288Instrumentation Cables211BS EN 50563External a.c.. d.c. and a.c.. a.c. power supplies. Determination of no-load power and average efficiency of active modes212BS EN 55022Information technology equipment Radio disturbance characteristics Limits and methods of measurement213BS EN 55024Information technology equipment - Immunity characteristics - Limits and methods of measurement214BS EN 60079Electrical Apparatus for Explosive Gas Atmospheres215BS EN 60309Plugs, socket-outlets and couplers for industrial purposes216BS EN 60534Flow Equations for Sizing Control Valves217BS EN 60598Luminaires. 218BS EN 60794.1.2Optical fibres, product specifications Test procedures219BS EN 60896Stationary lead-acid batteries 220BS EN 60898Electrical accessories Circuit breakers for overcurrent protection for household and similar installations Circuit-breakers for a.c. operation221BS EN 61082Preparation of documents used in electrotechnology Part 1: Rules222BS EN 61204Low-voltage power supplies, d.c. output223BS EN 61543Residual current-operated protective devices (RCDs) for household and similar use - Electromagnetic compatibility224BS EN 61558 Safety of Power Transformers, Power Supplies, Reactor and Similar Products225BS EN 62034Automatic test systems for battery powered emergency escape lighting226BS EN ISO 1461Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods227BS EN ISO 1182Reaction to fire tests for building products.Non combustibility test228BS EN ISO 2081Metallic and other inorganic coatings. Electroplated coatings of zinc with supplementary treatments on iron or steel229BS EN ISO 4126 Safety Devices for Protection against excess pressure230BS EN ISO 5167Measurement of Fluid Flow by means of Pressure Differential Devices in Circular Cross-Section Conduits Running Full.231BS EN ISO 5210Industrial Valves-Multi turn Valve Actuator Attachments232BS EN ISO 5211Industrial Valves. Part turn Actuator Attachment233BS EN ISO 5801Industrial fans-Performance testing using standardized airways234BS EN ISO 6817Method of Conductive Fluid Flow-rate in Closed Conduits Method Using Electromagnetic Flowmeters235BS EN ISO 6976Natural Gas Calculation of Calorific Value, Density and Relative Density & Wobbe index from composition236BS EN ISO 7235Acoustics: Laboratory Measurement Procedures for Ducted Silencers and Air Terminal Units237BS EN ISO 7240Fire Detection and Alarm Systems238BS EN ISO 7547Ships and Marine Technology: Air Conditioning and Ventilation of Accommodation Spaces. Design Conditions and Basis of Calculations239BS EN ISO 7933Ergonomics of the Thermal Environment Analytical Determination and interpretation of Heat Stress using Calculation of the Predicted Heat Strain240BS EN ISO 9934Non-destructive testing. Magnetic particle testing.241BS EN ISO 10418Petroleum and natural Gas Industries Offshore Production Installations basic Surface Process Safety System242BS EN ISO 10434Steel Gate Valves243BS EN ISO 10497Testing of valves. Fire type-testing requirements244BS EN ISO 10715Natural Gas, Sampling Guidelines245BS EN ISO 11925Reaction to fire tests for building products. Ignitability when subjected to direct impingement of flame.246BS EN ISO 12499Industrial fans - Mechanical safety of fans247BS EN ISO 12944Paints and varnishes248BS EN ISO 13480Metallic Industrial Piping249BS EN ISO 13501Fire Classification of Construction Products and Building elements.250BS EN ISO 13628.5Design and operation of subsea production systems Subsea umbilicals251BS EN ISO 13702Petroleum and natural gas industries. Control and mitigation of fires and explosions on offshore production installations. Requirements and guidelines252BS EN ISO 13703Petroleum and Natural Gas Industries Design and Installation of Piping Systems on Offshore Production Platforms.253BS EN ISO 14692Petroleum and Natural Gas Industries GPR Piping254BS EN ISO 14713Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures. 255BS EN ISO 15138Petroleum and Natural Gas industries: Offshore Production Installations: Heating, Ventilation and Air Conditioning256BS EN ISO 15589Oil & Gas Cathodic Protection of Pipelines257BS EN ISO 15761Gate, Globe and Check Small258BS EN ISO 15848Measurement, Test and Qualification procedures for Fugitive Emissions259BS EN ISO 17292Metal Ball Valves for Petroleum, Petrochemical and Allied Industries260BS EN ISO 17640Non-destructive testing of welds. Ultrasonic testing. Techniques, testing levels, and assessment261BS EN ISO 17776Petroleum and natural gas industries. Offshore production installations. Guidance on tools and techniques for hazard identification and risk assessment262BS EN ISO 19901Petroleum and natural gas industries. Specific requirements for offshore structures. 263BS EN ISO 19902Petroleum and natural gas industries. Fixed steel offshore structures264BS EN ISO 21457Petroleum, petrochemical and natural gas industries. Materials selection and corrosion control for oil and gas production systems265BS EN ISO 61508Functional safety of electrical/electronic/programmable electronic safety-related systems266BS EN ISO 61511Functional safety . Safety instrumented systems for the process industry sector 267BS ISO 76Rolling Bearings Static Load Ratings268BS ISO 281Rolling Bearings Dynamic Load Ratings and Rating Life269BS ISO 1940Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state 270BS ISO 4406Hydraulic Fluid Power - Fluids - Method for Coding the Level of Contamination by Solid Particles271BS ISO 5168Methods of Measurement of Fluid Flow Estimation of uncertainty of a flow-rate Measurement272BS ISO 5208Industrial Valves Pressure Testing of Metallic Valves273BS ISO 10302-1Acoustic Measurement of Airborne Noise Emitted and Structure-borne Vibration by Small Air-moving Devices274BS ISO 10790Measurement of fluid flow in closed conduits Guidance to the selection, installation and use of Coriolis meters (mass flow, density and volume flow275BS ISO 11064Ergonomic Design of Control Centres276BS ISO 11342Mechanical vibration. Methods and criteria for the mechanical balancing of flexible rotors277BS ISO 13347Industrial Fans: Determination of Fan Sound Power Levels under Standardised Laboratory Conditions 278BS ISO 14695Fans for General Purposes: Method of Measurement of Fan Vibration279BS ISO 15544Petroleum and Natural Gas Industries. Offshore Production Installations. Requirements and Guidelines for Emergency Response280BS ISO 15926 Industrial Automation Systems and Integration Integration of Life-Cycle Data281BS ISO 22899Determination of the resistance to jet fires of passive fire protection materials282BS ISO 80000Quantities and units 283BS PD ISO / TR 15377Measurement of Fluid Flow by means of Pressure Differential Devices Guidelines for the Specification of Orifice Plates, Nozzles and Venturi Tubes beyond the scope of ISO 5167284CENELEC CLC/TR 50426Assessment of inadvertent initiation of bridge wire electro-explosive devices by radio-frequency radiation285CENELEC CLC/TR 50427Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation286CSA T568.2-1-05Commercial Building Telecommunications Cabling Standard - Part 2: Balanced Twisted Pair Components - Addendum 1 - Transmission Performance Specifications for 4-Pair 100 Ohm Category 6A Cabling287DIN 50049Inspection Documents for the delivery of metallic product288DIN EN 301126-1Fixed Radio Systems. Conformance testing.Part 1: Point-to-Point equipment -Definitions, general requirements and test procedures289ETS/EN 300676Electromagnetic compatibility and Radio spectrum Matters (ERM), Ground-based VHF hand-held, mobile and fixed radio transmitters, receivers and transceivers for the VHF aeronautical mobile service using amplitude modulation; Technical characteristics and methods of measurement.290BS EN 61000Electromagnetic compatibility (EMC) Generic standards Immunity standard for industrial environments291DTI URN 02/609 (now DECC)Product Standards Equipment and protective Systems Intended for use in Potentially Explosive Atmospheres guidance Notes on the UK Regulations(ATEX)292DTI URN 05/1074 (now DECC)Products Standards Pressure Equipment Guidance Notes on the UK regulations (PED)293EEMUA 138Design & Installation of Online Analyser Systems294EEMUA 14490/10 Copper Nickel Alloy piping for Offshore Applications. Specification: Tubes Seamless and Welding295EEMUA 14590/10 Copper Nickel Alloy Piping for Offshore Applications. Specification: Flanges Composite and Solid296EEMUA 158Construction Specification for Fixed Offshore Structures in the North Sea297EEMUA 182Integral Block and Bleed Valves298EEMUA 191Alarm Systems. A Guide to the Design, Management and Procurement299EEMUA 196Valve Purchasers Guide to the European Pressure Equipment Directive300EEMUA 197Specification for the Fabrication of Non-Primary Structural Steelwork for Offshore Installations301EEMUA 218Quality Requirements for the manufacture and Supply of Duplex Stainless Steel302EIA/TIA (RS) 232Data Communication Interface Standard303EIA/TIA(RS) 485Data Communication Interface Standard304EN 10160 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) (replaces BS5996)305EN 302217Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas306ETS/EN 300338ETSI Telecommunications Standard Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mob307ETS/EN 300 373ETSI Telecommunication Standard Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for maritime mobile transmitters and receivers for use in the MF and HF bands308ICAOInternational Civil Aviation Organisation Aeronautical Telecommunications Annex 10309IEC 60028International standard of resistance for copper310IEC 60034 Rotating Electrical Machines311IEC 60038IEC Standard Voltages312IEC 60044Instrument transformers Part 1: Current transformers313IEC 60050International Electrotechnical Vocabulary314IEC 60051 Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts.315IEC 60059IEC standard current ratings316IEC 60060High voltage test techniques317IEC 60071Insulation co-ordination318IEC 60072Dimensions and output rating for rotating electrical machines319IEC 60073Basic and Safety Principles for Man-Machine Interface, Marking and Identification - Coding Principles for Indicators and Actuators320IEC 60076Power transformers321IEC 60079Electrical Apparatus for explosive gas atmospheres. Part 0: General Requirements322IEC 60085Electrical insulation - Thermal evaluation and designation323IEC 60092 Electrical Installations in Ships324IEC 60096Cables for radio frequencies325IEC 60099Surge arresters326IEC 60112 Method for determining the proof and the comparative tracking index of Solid insulating materials327IEC 60136 Dimensions of brushes and brush-holders for electrical machines328IEC 60137Insulated bushings for alternating voltages above 1 000 V329IEC 60145Var-hour (reactive energy) meters330IEC 60146Semiconductor converters331IEC 60156Insulating liquids - Determination of the breakdown voltage at power frequency - Test method332IEC 60158 Low Voltage Control Gear333IEC 60169-1 AMD 1Connectors for radio frequencies334IEC 60183Guide to the selection of high-voltage cables335IEC 60189Low frequency cables and wired with PVC insulation and PVC Sheath336IEC 60204Safety of machinery - Electrical equipment of machines337IEC 60211Maximum Demand Indicators, Class 1.0338IEC 60214Tap-changers. 339IEC 60215Safety rules for radio transmitters340IEC 60227Polyvinylchloride insulated cables of rated voltages up to and including 450/750 V341IEC 60228Conductors of insulated cables342IEC 60255Electrical Relays & Measuring relays and protection equipment343IEC 60268Equipment for electro-acoustic systems344IEC 60269 Low-voltage fuses345IEC 60270High-voltage test techniques Partial discharge measurements 346IEC 60282High-voltage fuses 347IEC 60287 Electric cables Calculation of the current rating348IEC 60304Standard colours for insulation for low-frequency cables and wires 349IEC 60309Plugs,socket-outlets and couplers for industrial purposes350IEC 60331 Fire Resisting Characteristics of Electrical Cables351IEC 60332Tests on Electrical and optical fibre cables under Fire Conditions352IEC 60364Low Voltage electrical installations in buildings353IEC 60398Industrial electroheating installations - General test methods354IEC 60417 DBGraphical symbols for use on equipment355IEC 60445Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors356IEC 60487Methods of measurement for equipment used in terrestrial radio-relay systems.357IEC 60488Standard digital interface for programmable instrumentation358IEC 60502Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) 359IEC 60519Safety in electroheating installations360IEC 60529Degrees of protection provided by enclosures (IP Code)361IEC 60533Electrical and electronic installations in ships Electromagnetic compatibility362IEC 60534Industrial Process Control Valves363IEC 60584Thermocouples364IEC 60598Luminaires365IEC 60617 DB SNAPSHOTGraphical symbols for diagrams-DATABASE SNAPSHOT366IEC 60622Secondary cells and batteries containing alkaline or other non-acid electrolytes - Sealed nickel-cadmium prismatic rechargeable single cells367IEC 60644Specification for high-voltage fuse-links for motor circuit applications368IEC 60688Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals369IEC 60695Fire hazard testing370IEC 60706Maintainability of equipment371IEC 60708Low frequency cables with polyolefin insulation and moisture barrier polyolefin sheath372IEC 60751Industrial platinum resistance thermometers and platinum temperature sensors373IEC 60754Test on gases evolved during combustion of materials from cables

374IEC 60793.2Optical fibres, product specifications375IEC 60794Optical fibre cables376IEC 60800Heating cables with a rated voltage of 300/500 V for comfort heating and prevention of ice formation377IEC 60811Electric and optical fibre cables - Test methods for non-metallic materials378IEC 60851Winding wires - Test methods379IEC 60885Electrical test methods for electric cables 380IEC 60898 Electrical accessories Circuit-breakers for overcurrent protection for household and similar installations381IEC 60909 Short-circuit currents in three-phase a.c. systems382IEC 60947 Low-voltage switchgear and controlgear383IEC 60950Information technology equipment

384IEC 61000Electromagnetic Compatibility (EMC).385IEC 61008Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs)386IEC 61009Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs)387IEC 61034Measurement of smoke density of cables burning under defined conditions388IEC 61069 Industrial Process Measurement and Control Evaluation of System Properties for the Purpose of System Assessment389IEC 61082Preparation of documents used in electrotechnology390IEC 61131Programmable Controllers391IEC 61140Protection against electric shock Common aspects for installation and equipment392IEC 61230Live working - Portable equipment for earthing or earthing and short-circuiting393IEC 61293Marking of electrical equipment with ratings related to electrical supply - Safety requirements394IEC 61326Electrical Equipment for Measurement, Control & Laboratory Use395IEC 61363Electrical installations of ships and mobile and fixed offshore units - Part 1: Procedures for calculating short-circuit currents in three-phase a.c.396IEC 61378Converter transformers397IEC 61439Low-voltage switchgear and controlgear assemblies398IEC 61508Functional Safety of Electrical/Electronic/Programmable Electronic Safety Related Systems399IEC 61511Functional Safety Safety Instrumented Systems for the Process industry Sector400IEC 61520Thermowells401IEC 61537Cable management - Cable tray systems and cable ladder systems402IEC 61554Panel mounted equipment - Electrical measuring instruments - Dimensions for panel mounting403IEC 61558Safety of power transformers, power supplies, reactors and similar products. Part 1: General requirements and tests404IEC 61672Electro acoustics - Sound level meters405IEC 61800Adjustable speed electrical power drive systems 406IEC 61850Communication networks and systems for power utility automation407IEC 61869Instrument transformers 408IEC 61892 Mobile and fixed offshore units -Electrical installations409IEC 61914Cable cleats for electrical installations410IEC 61935Specification for the testing of balanced and coaxial information technology cabling. 411IEC 62026Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) 412IEC 62040Uninterruptible power systems (UPS)413IEC 62052Electricity metering equipment (AC) - General requirements, tests and test conditions 414IEC 62053Electricity metering equipment (a.c.) - Particular requirements415IEC 62259Secondary cells and batteries containing alkaline or other non-acid electrolytes - Nickel-cadmium prismatic secondary single cells with partial gas recombination416IEC 62262Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)417IEC 62271 High-voltage switchgear and controlgear - ALL PARTS418IEC 62305Protection against lightning419IEC 62395Electrical resistance trace heating systems for industrial and commercial applications420IEC 62402Obsolescence management - Application guide421IEC 62444Cable glands for electrical installations422IEC CISPR 16Specification for radio disturbance and immunity measuring apparatus and methods 423IEC CISPR 61000 Electromagnetic Compatibility (EMC) 424IEC EN 60936Maritime navigation and radio communication equipment and systems425IEC/TR 60092-370Shipboard telecommunications cables and radio frequency cables. General instrumentation, control and communication cables426IEC/TR 60616Terminal and tapping markings for power transformer427IEC/TR 60894Guide for test procedure for the measurement of loss tangent of coils and bars for machine windings428IEC/TR 61439Low-voltage switchgear and controlgear assemblies 429IEC/TR 61641Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault430IEC /TR 61831Analyser Systems431432IEC/TR 61869-103Instrument transformers - The use of instrument transformers for power quality measurement433IEC Publication 244-2BMeasurement methods applicable to radio transmitters434IEC Publication 315Measurement methods for radio receivers of different classes of emission435IEERecommendations For The Electrical And Electronic Equipment Of Mobile And Fixed Offshore Installations436IEEE 519Recommended Practices and Requirements for Harmonic Control in Electrical Power Systems437IEEE 730Standard for Software Quality Assurance Plans (ANSI)438IEEE 802.11Wireless LAN Medium Access Control439IEEE 802.1DRapid reconfiguration of spanning tree recommendation440IEEE 802.3CSMA/CD (Ethernet)441IEEE 828Standard for Software Configuration Management Plans (ANSI)442IEEE 829Standard for Software Test Documentation443IEEE 830Guide for Software Requirements Specifications (ANSI)444IEEE 1008Standard for Software Unit Testing (ANSI)445IEEE 1012Standard for Software Verification and Validation Plans (ANSI)446IEEE 1016Recommended Practice for Software Design Descriptions447ISA 5.1Instrumentation Symbols and Identification448ISA 7.0.1Quality Standard for Instrument Air449ISA 51.1Process Instrumentation Terminology450ISA 75.01Flow Equations for Sizing Control Valves451ISA 75.03Face-to-Face Dimensions for Flanged Globe-Style Control Valves Bodies: ANSI Classes, 125, 150, 250, 300, and 600.452ISA 75.07Laboratory Measurement of Aerodynamic Noise Generated by Control Valves453ISA 75.08Face to Face Dimensions for Integral Flanged Globe Style Control Valve Bodies (ANSI Classes 125, 150, 300, & 600)454ISA 75.16Control Valve Cavitation455ISA TR 99 All PartsManufacturing and Control Systems Security456ISO 834Fire-resistance tests-Elements of Building Construction457ISO 14313Valves- Pipeline458ISO/IEC Directives, Part 2Rules for the structure and drafting of International Standards459ITU-R BT.656Interface for digital component video signals in 525-line and 625-line television systems460ITU-R BT.796Parameters for enhanced compatible coding systems based on 625-line pal and secam television systems461ITU-R F.752Diversity techniques for point-to-point fixed wireless systems462ITU-R M.478Technical characteristics of equipment and principles governing the allocation of frequency channels between 25 and 3000 MHz for the FM Land Mobile service463ITU-R M.1225Guidelines for evaluation of radio transmission464ITU-R P.368Ground-wave propagation curves for frequencies between 10 kHz and 30 MHz465ITU-R P.525Calculation of free-space attenuation466ITU-R P.528Propagation curves for aeronautical mobile and radio navigation services using the VHF, UHF and SHF bands467ITU-R P.530Propagation data and prediction methods required for the design of terrestrial line-of-sight systems.468ITU-R P.1410Propagation data and prediction methods469ITU-R SA.363Space operation systems. Frequencies, bandwidths and protection criteria470ITU-T G.114Guidance on one-way delay for Voice over IP471ITU-T G.131Talker echo and its control472ITU-T G.652Single mode fibres (1300 nm)473ITU-T G.653Single mode fibres (1550 nm)474ITU-T G.654Single mode fibres (1530 - 1625 nm)475ITU-T G.655Single mode fibres (1530 - 1565 nm)476ITU-T G.707SDH network node interface477ITU-T G.708SDH network node interface478ITU-T G.711Pulse code modulation for Voice frequencies479ITU-T G.729Coding of speech at 8kbit/s using conjugate- structure algebraic code excited linear prediction480ITU-T G.780SDH vocabulary481ITU-T G.783SDH equipment functional blocks482ITU-T G.784SDH Management.483ITU-T G.803Architecture of transport networks based on the synchronous digital hierarchy (SDH)484ITU-T G.805Generic functional architecture of transport networks485ITU-T G.813Timing characteristics of SDH equipment slave clocks (SEC)486ITU-T G.823The control of jitter and wander within digital networks which are based on the 2048 kbit/s hierarchy487ITU-T G.825The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH)488ITU-T G.826End-to-end error performance parameters and objectives for international, constant bit-rate digital paths and connections489ITU-T G.828Error performance parameters and objectives for international, constant bit rate synchronous digital paths490ITU-T G.841Types and characteristics of SDH network protection architectures491ITU-T G.842Interworking of SDH protection architectures492ITU-T G.872Architecture of optical transport networks493ITU-T G.911Parameters and calculation methodologies for reliability and availability of fibre optic systems494ITU-T G.957Optical interfaces for equipments and systems relating to the synchronous digital hierarchy495ITU-T G.977Repeatered optical submarine systems496ITU-T H.323Packet-Based Multimedia Communications Systems497ITU-T K.11Surge protectors and recommendation for telecom equipment498ITU-T K.18Calculation of voltage induced into telecommunication lines from radio station broadcasts and methods of reducing interference499ITU-T L.1Construction, installation and protection of telecommunication cables in public networks500ITU-T M.2100Commissioning and maintenance (measurement procedures)501ITU-T M.2110SDH and PDH commissioning (measurement procedures)502ITU-T M.2120Fault detection (PDH and SDH)503ITU-T M.3010Principles for a Telecommunication Management Network504ITU-T M.3100Generic Network Information Model505ITU-T RECOMMENDATI ON T.30for document facsimile transmission in the general switched telephone network506ITU-T RECOMMENDATI ON T.37Procedures for the transfer of facsimile date via store-and forward on the Internet507ITU-T RECOMMENDATI ON T.38Procedures for real-time Group 3 facsimile communication over IP networks508ITU-T X.209Encoding rules specification of Basic Encoding Rules509ITU-T X.690Encoding rules specification of Basic Encoding Rules510MSS SP6Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings511MSS SP25Standard Marking System for Valves, Fittings, Flanges and Unions512MSS SP44Steel Pipe Line Flanges513MSS SP75Fittings High Yield Steel514MSS SP80Bronze Gate, Globe, Angle and Check Valves515MSS SP97Branch Outlet Fittings516NACE MR0175/ISO 15156Petroleum and natural gas industries. Materials for use in H2S-containing.Environments in oil and gas production517NFPA 1FIRE CODE518NFPA 10Standard for Portable Fire Extinguishers519NFPA 11Standard for Low, Medium and High Expansion Foam520NFPA 11ASTANDARD FOR MEDIUM AND HIGH EXPANSION FOAM SYSTEMS521NFPA 12Standard on Carbon Dioxide Extinguishing Systems522NFPA 13Installation of Sprinkler Systems523NFPA 14STANDARD FOR THE INSTALLATION OF STANDPIPE AND HOSE SYSTEMS524NFPA 15Standard for Water Spray Fixed Systems for Fire Protection525NFPA 16Standard for Installation of Foam-Water Sprinkler and Foam-Water Spray Systems526NFPA 17Standard for Dry Chemical Extinguishing Systems527NFPA 17AStandard for Wet Chemical Extinguishing Systems528NFPA 20Standard for the Installation of Stationary Fire Pumps for Fire Protection529NFPA 30FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE530NFPA 72National Fire Alarm and Signalling Code531NFPA 75STANDARD FOR THE FIRE PROTECTION OF INFORMATION TECHNOLOGY EQUIPMENT532NFPA 76STANDARD FOR THE FIRE PROTECTION OF TELECOMMUNICATIONS FACILITIES533NFPA 90AStandard for the Installation of Air-Conditioning and Ventilating Systems534NFPA 96Standard for Ventilation Control and Fire protection of Commercial Cooking Operations535NFPA 101LIFE SAFETY CODE536NFPA 111STANDARD ON STORED ELECTRICAL ENERGY EMERGENCY537NFPA 496Standard for Purged and Pressurised Enclosures for Electrical Equipment538NFPA 750Standard for Water Mist Fire protection Systems539NFPA 2001Standard for Clean Agent Fire Extinguishing SystemsOffshore Standards -DNVDNV-OS-A101Safety Principles and ArrangementsDNV-OS-A201Winterization for Cold Climate Operations (Tentative)DNV-OS-B101Metallic MaterialsDNV-OS-C101Design of Offshore Steel Structures, General (LRFD Method)DNV-OS-C102Structural Design of Offshore ShipsDNV-OS-C103Structural Design of Column Stabilised Units (LRFD Method)DNV-OS-C104Structural Design of Self-Elevating Units (LRFD Method)DNV-OS-C105Structural Design of TLPs (LRFD Method)DNV-OS-C106Structural Design of Deep Draught Floating Units (LRFD Method)DNV-OS-C201Structural Design of Offshore Units (WSD Method)DNV-OS-C301Stability and Watertight IntegrityDNV-OS-C401Fabrication and Testing of Offshore StructuresDNV-OS-C501Composite ComponentsDNV-OS-C502Offshore Concrete StructuresDNV-OS-C503Concrete LNG Terminal Structures and Containment SystemsDNV-OS-D101Marine and Machinery Systems and EquipmentDNV-OS-D201Electrical InstallationsDNV-OS-D202Automation, Safety, and Telecommunication SystemsDNV-OS-D203Integrated Software Dependent System (ISDS)DNV-OS-D301Fire ProtectionDNV-OS-E101Drilling PlantDNV-OS-E201Oil and Gas Processing SystemsDNV-OS-E301Position MooringDNV-OS-E302Offshore Mooring ChainDNV-OS-E303Offshore Fibre RopesDNV-OS-E304Offshore Mooring Steel Wire RopesDNV-OS-E401Helicopter DecksDNV-OS-E402Offshore Standard for Diving SystemsDNV-OS-E403Offshore Loading BuoysDNV-OS-E406Design of Free Fall LifeboatsDNV-OS-E407Underwater Deployment and Recovery SystemsDNV-OS-F101Submarine Pipeline SystemsDNV-OS-F201Dynamic RisersDNV-OS-H101Marine Operations, GeneralDNV-OS-H102Marine Operations, Design and FabricationDNV-OS-H201Load Transfer OperationsDNV-OS-H203Transit and Positioning of Offshore UnitsDNV-OS-H204Offshore Installation Operations (VMO Standard Part 2-4)DNV-OS-J101Design of Offshore Wind Turbine StructuresDNV-OS-J103Design of Floating Wind Turbine StructuresDNV-OS-J201Offshore Substations for Wind FarmsDNV-OS-J301Wind Turbine Installation Units

Recommended PracticesDNV-RP-A201Plan Approval Documentation Types DefinitionsDNV-RP-A203Technology QualificationDNV-RP-A204Quality Survey Plan (QSP) for Offshore Class New-building SurveysDNV-RP-A205Offshore Classification Projects - Testing and CommissioningDNV-RP-B101Corrosion Protection of Floating Production and Storage UnitsDNV-RP-B401Cathodic Protection DesignDNV-RP-C101Allowable Thickness Diminution for Hull Structure of Offshore ShipsDNV-RP-C102Structural Design of Offshore ShipsDNV-RP-C103Column-Stabilised UnitsDNV-RP-C104Self-elevating UnitsDNV-RP-C201Buckling Strength of Plated StructuresDNV-RP-C202Buckling Strength of ShellsDNV-RP-C203Fatigue Design of Offshore Steel StructuresDNV-RP-C204Design against Accidental LoadsDNV-RP-C205Environmental Conditions and Environmental LoadsDNV-RP-C206Fatigue Methodology of Offshore ShipsDNV-RP-C207Statistical Representation of Soil DataDNV-RP-C208Determination of Structural Capacity by Non-linear FE analysis MethodsDNV-RP-C301Design, Fabrication, Operation and Qualification of Bonded Repair of Steel StructuresDNV-RP-C302Risk Based Corrosion ManagementDNV-RP-D101Structural Analysis of Piping SystemsDNV-RP-D102Failure Mode and Effect Analysis (FMEA) of Redundant SystemsDNV-RP-D201Integrated Software Dependent SystemsDNV-RP-D202Witnessing of Low Sulphur Fuel Changeover and OperationsDNV-RP-E101Recertification of Well Control Equipment for the Norwegian Continental ShelfDNV-RP-E102Recertification of Blowout Preventers and Well Control Equipment for the US Outer Continental ShelfDNV-RP-E301Design and Installation of Fluke AnchorsDNV-RP-E302Design And Installation of Plate Anchors in ClayDNV-RP-E303Geotechnical Design and Installation of Suction Anchors in ClayDNV-RP-E304Damage Assessment of Fibre Ropes for Offshore MooringDNV-RP-E306Dynamic Positioning Vessel Design Philosophy GuidelinesDNV-RP-E307Dynamic Positioning Systems - Operation GuidanceDNV-RP-E401Survey of Diving SystemsDNV-RP-E402Naval Rescue SubmersiblesDNV-RP-E403Hyperbaric Evacuation SystemsDNV-RP-F101Corroded PipelinesDNV-RP-F102Pipeline Field Joint Coating and Field Repair of Linepipe CoatingDNV-RP-F103Cathodic Protection of Submarine Pipelines by Galvanic AnodesDNV-RP-F105Free Spanning PipelinesDNV-RP-F106Factory Applied External Pipeline Coatings for Corrosion ControlDNV-RP-F107Risk Assessment of Pipeline ProtectionDNV-RP-F108Fracture Control for Pipeline Installation Methods Introducing Cyclic Plastic StrainDNV-RP-F109On-Bottom Stability Design of Submarine PipelinesDNV-RP-F110Global Buckling of Submarine Pipelines Structural Design due to High Temperature/High PressureDNV-RP-F111Interference Between Trawl Gear and PipelinesDNV-RP-F112Design of Duplex Stainless Steel Subsea Equipment Exposed to Cathodic ProtectionDNV-RP-F113Pipeline Subsea RepairDNV-RP-F116Integrity Management of Submarine Pipeline SystemsDNV-RP-F118Pipe Girth Weld AUT System Qualification and Project Specific Procedure ValidationDNV-RP-F201Design of Titanium RisersDNV-RP-F202Composite RisersDNV-RP-F203Riser InterferenceDNV-RP-F204Riser FatigueDNV-RP-F205Global Performance Analysis of Deepwater Floating StructuresDNV-RP-F206Riser Integrity ManagementDNV-RP-F301Subsea Separator Structural DesignDNV-RP-F302Selection and use of Subsea Leak Detection SystemsDNV-RP-F401Electrical Power Cables in Subsea ApplicationsDNV-RP-G101Risk Based Inspection of Offshore Topsides Static Mechanical EquipmentDNV-RP-G103Non-Intrusive InspectionDNV-RP-H101Risk Management in Marine and Subsea OperationsDNV-RP-H102Marine Operations during Removal of Offshore InstallationsDNV-RP-H103Modelling and Analysis of Marine OperationsDNV-RP-H104Ballast, Stability, and Watertight Integrity - Planning and Operating GuidanceDNV-RP-J101Use of Remote Sensing for Wind Energy AssessmentsDNV-RP-J201Qualification Procedures for CO2 Capture TechnologyDNV-RP-J202Design and Operation of CO2 PipelinesDNV-RP-J203Geological Storage of Carbon DioxideDNV-RP-J301Subsea Power Cables in Shallow Water Renewable Energy ApplicationsDNV-RP-O401Safety and Reliability of Subsea SystemsDNV-RP-O501Erosive Wear in Piping SystemsDNV-RP-U301Risk Management of Shale Gas Developments and Ope

&P of &N

Sheet2

Sheet3