CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to...
Transcript of CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to...
![Page 1: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/1.jpg)
Removal and Cleaning
CM3 Photo-Eye Ice Sensor
![Page 2: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/2.jpg)
Removal
•Remove Front Panel
•Harvest any ice
•Shut unit off
![Page 3: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/3.jpg)
Removal
•Remove Evaporator Cover
![Page 4: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/4.jpg)
Removal
•Pull Cube Deflector Out From Under Evaporators
![Page 5: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/5.jpg)
Removal Cascading Shield
•Locate Cascading Shield
•Push Bottom of Shield Back to Release From Tabs on Eye Holders
Cascading Shield Push Bottom
Edge Back
Tab
![Page 6: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/6.jpg)
Remove Cascading Shield
•Lift the shield off the eye-holder tabs. Then pull forward and down, out from under the evaporators.
Cascading Shield
![Page 7: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/7.jpg)
Un-Bundle Wires
•Photo-eye wires may be bundled together. Unbundle them to get slack so the eyes can be removed.
![Page 8: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/8.jpg)
Remove Eye-Holders
•Pull the holders out of the left and right walls by pulling on the tabs.
![Page 9: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/9.jpg)
Clean the Photo-Eyes
•Push in to release module from holder
•Gently remove scale from lenses, use soft cloth and diluted scale remover.
Lenses
Note: Prior design did not have separate module.
![Page 10: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/10.jpg)
Reassembly
•Snap module back into holder
•Be sure wire is clipped as shown
• Insert holders into wall of freezing compartment
•Place cascading shield onto holder
•Snap onto tabs
![Page 11: CM3 Photo-Eye Ice Sensor.ppt Training/CM3 Phot… · tabs. Clean the Photo-Eyes •Push in to release module from holder •Gently remove scale from lenses, use soft cloth and diluted](https://reader034.fdocuments.net/reader034/viewer/2022042319/5f0948bb7e708231d42616b4/html5/thumbnails/11.jpg)
Reassembly
•Note how cascading shield snaps onto eye holder tab