16-34012-00

Unit Construction

Front sub frame

Rear sub frame (4WD)

Rear sub frame (2WD)

1. SPECIFICATION

Body mounting:4-points bushTransaxle mounting:2-points bushWeight: 22.37 kg

1.

2.

3.

Body mounting:4-points bushAxle mounting:4-points bushWeight: 16.61 kg

1.

2.

3.

Body mounting:40 points direct mountingSpring link:Direct mounting without bracket on rear cross memberWeight: 12.74 kg

1.

2.

3.

BRKT-ENG MTG RR BRKT-ENG MTG FRT

16-4

4. Transaxle mounting (Rear)3. Rear mounting (LH & RH)

2. Front mounting (LH & RH)

1. Transaxle mounting (Front)

2. TIGHTENING TORQUE

Bolt (17 mm) / Nut (17 mm)

68.6 to 88.2 Nm

Bolt (17 mm) 88.2 to 107.8 Nm

Bolt (17 mm) 88.2 to 107.8 Nm

2 Bracket mounting bolts (17 mm)

88.2 to 107.8 Nm

Bolt (14 mm) / Nut (14 mm)

68.6 to 88.2 Nm

3 Bolts (14 mm) 29.4 to 49.0 Nm

Front sub frame - based on 4WD▶

16-54012-00

8. Other connections for rear sub frame (LH & RH)

7. Rear axle mounting

5. Front mounting (LH & RH)

Bolt (17 mm) 88.2 to 107.8 Nm

6. Rear mounting (LH & RH)

Bolt (17 mm) 88.2 to 107.8 Nm

Rear mounting bolt (14 mm) 68.6 to 88.2 Nm

Upper arm bolt (17 mm) / Nut (19 mm)

98.0 to 117.6 Nm

Lower arm nut/Bolt (19 mm)

98.0 to 117.6 Nm

Rear sub frame - based on 4WD▶

Rear mounting bolt (17 mm) 107.8 to 127.4 Nm

16-6

Installation Sectional diagram

1. Front

2. Rear Mounting bracket Mounting bolt

3. Transaxle mounting (Front) For manual transaxle For automatic transaxle (diesel)

4. Transaxle mounting (Rear)

1) Sectional Diagram and Bolts for Front Sub Frame

Mounting nut29.4 to 39.2 Nm

Bolt 9.4 to 39.2 Nm

16-74012-00

2) Sectional Diagram and Bolts for Rear Sub FrameInstallation Sectional structure

1. Front 4WD 2WD

2. Rear 4WD 2WD

3. Rear axle - Front (4WD)

4. Rear axle - rear (4WD)

16-8

The front sub frame consists of 4 body bush mountings(A) and 2 engine bush mountings(B) which reduce the vibration from the powertrain and road, and also control the torque. And the two engine bush mountings consist of an engine mounting which supports the engine powertrain and a transmission mounting. The engine side and transmission side mountings are rubber mountings with brackets and insulators while the body mounting is a rubber bush mounting which is fitted to the frame.

Installation of front sub frame (4WD)

The installation of the front sub frame is the same for both automatic transmission and manual transmission. For 4WD, the PTU and the propeller shaft are installed.

Installation of front sub frame (2WD)

The installation of the front sub frame is the same for both automatic transmission and manual transmission.

PTU assembly

16-94015-01

Installation of rear sub frame (4WD)

The installation of the rear sub frame is the same for both automatic transmission and manual transmission. For 4WD, the E-coupling, propeller shaft and rear axle are installed.

Installation of rear sub frame (2WD)

The installation of the rear sub frame is the same for both automatic transmission and manual transmission.

The rear sub frame system consists of body bush mountings and direct mountings which reduce the vibration transmitted from the powertrain and road to the vehicle body.For 4WD, it consists of 4 body mountings (bush mountings) and 2 axle mountings (bush mountings) and for 2WD, it consists of 4 body mountings (direct mountings).