Assemble 1352

X340 (MS-1352) Assembly Guide

■ 1、LCD MODULE ASSY

■ 2、UPPER CASE ASSY

■ 3、LOWER CASE ASSY-2

■ 4、RAM MODULE

■ 5、LOWER CASE ASSY-1

■ 6、WLAN MODULE

■ 7、HDD MODULE

■ 8、ASSEMBLE UPPER CASE AND LOWER CASE

■ 9、KEYBOARD

■ 10、LOWER CASE ASSY

■ 11、BATTERY PACK

X340（MS-1352）Assembly Guide

1、LCD MODULE ASSY

1.1：Assemble the Antenna board to the LCD cover

fixed position as left picture shows;

Component P/N Qty

L-Antenna S79-1800H30-J51 1

R-Antenna S79-1800H40-J51 1

LCD Cover 307-351A213-TC7 1

1.2：Assemble the MIC Module as left picture

Shows;

Attention：MIC Module needs along with LCD

Cover flute.

Component Part No Qty

MIC Module S34-2100900-N44 1

1.3：Cover MIC Module with MIC Sponge as

left picture shows;


MIC Sponge E2Y-3511911-Y42 1


1、LCD MODULE ASSY

1.4：Assemble CMOS Camera Module follow the

instruction as left picture shows. Then stick the

copper film to the LCD cover to fix the module.

Attention：Don’t assemble the CMOS Camera

Module with too strong force avoid damage the

module.


Camera Module S1F-0001460-B36 1

1.5：Connect the Coaxial Cable（Camera Cable）

in the direction of the arrow in the picture;

1.6：Arrange the cable to the fixed position as the

picture shows;

Attention: MIC Cable and Camera Cable cannot lap

over when arranging avoid damage the panel.


1、 LCD MODULE ASSY

1.7：Connect LVDS Cable to Display Module and

fix the cable with black tape;

Component P/N Qty

LVDS Cable K19-3023002-V03 1

1.8：Insert the Display Module to the slot from left

side and make it be placed into the LCD Cover

completely.


Display Module S1J-342G001-CC1 1

1.9：Shift the hook to be locked state in the

direction of the arrow. Then stick the two

Hook Sponge to fix.


Hook Sponge E2Y-3511411-Y42 2



1.10：Stick three magnet to the position as left

picture shows;


LCD Cover Magnet E2Y-3510711-SF7 2

LCD Cover Magnet E2Y-3511011-SF7 1

1.11：Assemble the left and right LCD Hinge as left

picture shows;


Hinge R E2M-3510111-G60 1

Hinge L E2M-3510211-G60 1

1.12：Lock 8pcs M2*3mm screws with auto driver;

Attention：Set the auto-driver force at

2.0-2.2Kgf-cm.


Screw E43-1203003-H29 8



1.13：When assemble LCD Bezel, please start

from down wards. Assemble the 5pcs hooks

downward to be ok and then right, top wards,

finally the left hook.


LCD Bezel 307-351B213-TC7 1

1.14：Arrange the left and right Hinge Cap as left

picture shows;

Attention：Cannot press the cables when assemble

the hinge cap.


Hinge Cap E2P-3510321-Y31 2

1.15：Stick the 4pcs Cover Rubber and 1pcs Bezel

Rubber as left picture shows;


Cover Rubber E2Y-3510111-Y40 4

Bezel Rubber E2Y-3510211-Y40 1


2、UPPER CASE ASSY

2.1：Assemble the Touchpad Module to Upper

Case fixed position and then cover it with Mylar;


Touchpad Module S78-3700360-SK9 1

Upper Case 307-351C213-Y31 1

2.2：Assemble Touchpad Board to Upper Case

fixed position and then lock 2pcs 2*3.5mm screws;

Attention：Set the auto-driver force at.1.5-2.0

Kgf-cm


Screw E43-1203501-H29 2

Touchpad Board 607-1352Q-01S 1

2.3：Connect the Touchpad Cable (To Button

Board) to Touchpad Module, fix the Touchpad

Cable with hook; Then paste the acetate tape on

the connector and cable.


FFC Cable (To MB) K1C-1012038-J36 1

FFC Cable (To Button) K1C-1020006-J36 1


3、LOWER CASE ASSY-2

3.1：Assemble Speaker Module to Lower Case,

lock 3pcs M2*3.5mm screws with auto-driver;

Attention：Set the auto-driver force at. 1.5-1.8

Kgf-cm.


Screw E43-1203501-H29 3

Speaker Module S33-A020210-F33 1

Lower Case 307-351D212-W28 1

3.2：Assemble R USB Cover to Lower Case fixed

position.


R USB Cover E2P-3511111-D37 1

3.3：Assemble SD Card Cover to Lower Case fixed

position.


SD Card Cover E2P-3511311-D37 1



3.4：Assemble L HDMI Cover to Lower Case fixed

position.


L HDMI Cover E2P-3511211-D37 1

3.5：Assemble Fan to M/B as left picture shows;

Attention：Fan Cable needs go from the M/B hole.


Fan E33-0800080-MC2 1

Main Board 607-13521-02S 1

3.6：Assemble the M/B to Lower Case fixed

position.



3.7：Lock 2pcs M2*3.5mm screws with auto-driver;

Attention：Set the auto-driver force at.

1.5-2.0Kgf-cm.


Screw E43-1203501-H29 2

3.8：Assemble 2 screws (M2*3.5mm);

Attention: the screw driver torque is 1.5-2.0Kgf-cm


Screw E2P-3510811-D37 2

3.9：Firstly assemble the heatsink, then Assemble

3 screws (M2*3.5mm);

Attention：the screw driver torque is 1.5-2.0Kgf-cm

Component P/N Qty

Screw E43-1203501-H29 3

Heatsink E31-0801210-TA9 1

3

1

2

1

1

2

2



3.10：Assemble Bluetooth Module as left picture

shows;


Bluetooth Module 605-6837D-150 1

3.11：Lock 1pcs M2*3.5mm screws with auto

driver;


1.5-2.0Kgf-cm


Screw E43-1203501-H29 1

3.12：Connect the Bluetooth Cable in the direction

of the arrow in left picture；


Bluetooth Cable K10-3008091-H39 1



3.13：Assemble the DSUB cover and MODE cover

on left side I/O board;

Component P/N Qty

DSUB Cover E2P-3510811-D37 1

MODE Cover E2P-3510711-D37 1

3.14：Assemble the left side I/O port as left pic

shows:

Component P/N Qty

Left Side I/O Board 607-1352O-01S 1

3.15：Assemble the 3 screw (M2*3.5mm)


Component P/N Qty

Screw E43-1203501-H29 3


4、RAM MODULE

4.1：Insert RAM Module to the slot in the direction

of arrow in the left picture.

Component P/N Qty

RAM Module S7C-S357102-T10 1

4.2：Check the hook to fix RAM Module to be OK.



5.1：Assemble LCD Module and then lock 3pcs

M2*3.5mm screws to fix the left hinge;


1.5-2.0Kgf-cm


Screw E43-1203501-H29 3

5.2：Then lock 4pcs M2*3.5mm screws to fix the

right hinge；


1.5-2.0Kgf-cm


Screw E43-1203501-H29 4



5.3：Assemble Audio Cover and DCIN Cover to

Right Side I/O Board. Then connect LINK Cable to

the little board.


LINK Cable K10-3024011-H39 1

Audio Cover E2P-3511411-D37 2

DCIN Cover E2P-3510911-D37 1

5.4：Assemble Right Side I/O Board as left picture

shows;


Right Side I/O Board 607-1352N-02S 1

5.5：Lock 3pcs M2*3.5mm screws with auto

driver;


1.5-2.0Kgf-cm


Screw E43-1203501-H29 3



5.6：Connect Speaker Cable and MIC Cable in the

direction of the arrow in the picture;

5.7：Then connect LINK Cable;

5.8：Finally connect LVDS Cable;

MIC Cable

Speaker Cable


6、WLAN MODULE

6.1：Insert WLAN Module in the direction of arrow

in the left picture;


WLAN Module S57-0800183-I06 1

6.2：Lock 1pcs M2*3.5mm screws with auto driver;


1.5-2.0Kgf-cm.


Screw E43-1203501-H29 1

6.3：Connect the left and right antenna to the

WLAN Module as left picture shows.


6、WLAN MODULE

6.4：Assemble the Wlan board as left pic shows:

Component P/N Qty

Wlan Board 607-1352P-01S 1

6.5：Assemble 2 screws(M2*3.5mm)


Component P/N Qty

Screw E43-1203501-H29 2


7、HDD MODULE

7.1：Assemble 3 Brackets to the HDD fixed

position.


HDD Bracket 307-3510611-A89 3

HDD Module S71-2432504-F06 1



1.5-2.0Kgf-cm.


Screw E43-1303502-H29 3


7、HDD MODULE

7.3：Assemble HDD Module in the direction of

arrow in the left picture；



1.5-2.0Kgf-cm.


Screw E43-1203501-H29 2


8、ASSEMBLE UPPER CASE AND LOWER CASE

8.1：Connect Touchpad Cable in the direction

of arrow and then fix Touchpad Cable with hook;

8.2：When assemble Upper Case，please start

from down wards hooks to be ok and then left

& right, finally the top.

8.3：Lock 6pcs M2*3.5mm screws in turn shown

in the picture with auto-driver;


1.5-2.0Kgf-cm.


Screw E43-1203501-H29 6


9、KEYBOARD

9.1：Connect the K/B cable in the direction of arrow

in the left picture and then fix the cable by pushing

the drawer;


Keyboard S1N-1ETC211-SA0 1

9.2：When assemble the K/B, first from the two

sides hook and then the top. Make sure all the

hooks are assembled to be OK.


10、LOWER CASE ASSY

10.1：Lock 10pcs M2*2.5mm screws in turn with

auto driver;


1.5-2.0Kgf-cm.


Screw E43-1202506-H29 10

10.2：Insert the Dummy Card in the direction of

arrow in the left picture.


Dummy Card E2P-3512611-Y31 1


11、BATTERY PACK

11.1：Assemble Battery Pack in the direction of

arrow in the left picture；

Attention：Battery Pack needs to slide into the slot

from the Open mark.


Battery Pack S9N-2141200-SB3 1

11.2：Shift Unlock button to lock Battery Pack.

（MS-1352）screws specification

Photo Screw specification Label

(M2*L2.5MM) white

(M2*L3MM) white

(M2*L3.5 MM) black

(M3*L3.5 MM) white


■ 1、Lower Case ASSY total 10pcs screws;

specification：


(M2*L2.5 MM) white


■ 2、Upper Case ASSY total 6pcs Screws;

specification：


(M2*L3.5 MM) black


■ 3、Lower Case ASSY total 16pcs Screws;

specification：


(M2*L3.5 MM) black


■ 4、WLAN Module total 1pcs screws;

specification：


(M2*L3.5 MM) black


■ 5、HDD Module total 5pcs screws;

specification：


(M2*L3.5 MM) black

(M3*L3.5 MM) white


■ 6、THERMAL-KIT total 5pcs screws:

specification：


(M2*L3.5 MM) black


■ 7、Mainboard total 2pcs screws:

specification：


(M2*L3.5 MM) black


■ 8、 Speaker Module total 3pcs screws；

specification：


(M2*L3.5 MM) black


■ 9、 LCD Hinge total 8pcs screws；

specification：


(M2*L3MM) white

Assemble 1352

Documents

Transcript of Assemble 1352