ASSA ABLOYextranet.assaabloydss.com/library/installation... · ASSA ABLOY ... assa abloy

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2015 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9357-0005-020 ( )06-15

6

2

31

4

8 7 9 12

10

5

11

ASSA ABLOY80-9357-0005-020 (06-15)

Tools required:

• 1/8” allen wrench (included) • Power drill and set of drill bits• Flat blade screwdriver (potentiometer & terminal size) • Center punch• Screwdriver (Phillips size 2) • Wire stripper• Tape ruler • #7 drill 1/4-20 tap (metal frame install)

5700 Power OperatorStop (Push) Side Mount

Installation and Instruction Manual

Series

Item No. Description

1 Back plate

2 Door Closer (1601LAP or 1601BFLAP)

3 Motor Assembly (5700M)

4 Inverter (5700IN)

5 Cover (5700COV)

6 On/Off switch

7 Circuit Breaker

8 120VAC Electrical Connections

9 Activation Inputs

10 Door Open/Closed Position Magnets

11 Optional RF Receiver12 Power Supply - 1.1A 24V

· Always disconnect the main power to the operator prior to servicing or cleaning.

· To reduce the risk of injury or person, use the operator only with Pedestrian Swing doors.

· This operator is for indoor use only.

· 120VAC power supplied to the operator must be a dedicated circuit from the main circuit breaker panel and must NOT be connected into any building lighting system that operates flourescent lights.

· Maximum door size: 48 in (1219mm) wide x 250 lb (113.4kg).

WARNINGS!

Patents 5,881,497; 7,316,096; 7,484,333

5-1/4 (133)Min CeilingClearance

4-3/8(111)

2 (51)FrameFace

2(51)


ASSA ABLOY

80-9357-0005-020 ( )06-15

Hollow Metal Door Frame Reinforcing

FrameMaterial

12 Ga..1046 (2.66)

14 Ga..0747 (1.90)

16 Ga..0598 (1.52)

18 Ga..0478 (1.21)

12 Ga..1046 (2.66)

10 Ga..1343 (3.41)

10 Ga..1343 (3.41)

8 Ga..1644 (4.18)

18 Ga..0478 (1.21)

12 Ga..1046 (2.66)

12 Ga..1046 (2.66)

10 Ga..1343 (3.41)

Reinforcing

Recommended Min. Required

Contents

General Information· UL labeled fire or smoke barrier door assemblies require that

the 120VAC (60Hz) power input to the LEO door operator be supplied through normally closed alarm contacts of the alarm system / alarm panel.

· Power input to LEO door operator must be 120VAC (60Hz) to terminals HOT and COM at terminal strip T1. Earth ground (GND) to green screw on backplate.

· All wiring must conform to standard wiring practice in accordance with national and local wiring codes.

· Note: Unless otherwise noted, all dimensions are given in inches (millimeters).

· Minimum suggested and required material thickness for hollow metal frames (skin plus reinforcement) is charted on below.

· Unit is Non-Handed.

· Door must be hung on butt hinges [5” (127mm) max. width] or 3/4” (19mm) offset pivots. A separate door and frame preparation template will be supplied for other conditions.

· Door must swing freely through the entire opening and closing cycle before beginning the installation.

· Use of an auxiliary door stop (by others) is always recommended.

· An incorrectly installed or improperly adjusted door operator can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.

WARNING: Make sure 120VAC (60Hz) input power is turned off at facility’s main circuit breaker before proceeding with installation.

General Templating Information:· Before beginning the installation, verify that the door frame is

properly reinforced and is well anchored in the wall.

· Unreinforced hollow metal frames and aluminum frames should be prepared and fitted with 1/4-20 blind rivet nuts, furnished by others.

· Concealed electrical conduit and concealed switch or sensor wires should be pulled to the frame before proceeding.

Fasteners for Frame:· 1/4-20 machine screws for hollow metal and aluminum.· No. 14 x 2-3/4” (70mm) long sheet metal screws for wood.

Fasteners for Door:· 1/4-20 machine screws.· 3/8” diameter x 1-5/8” (41mm) long sex nut.

Electrical Information:· Maximum current draw of unit is 0.6 amps.

· Breaker Switch protects the motor assembly and inverter; and has a 3 amp rating.

· Maximum wire size is:12AWG at terminals HOT and COM (120VAC; 60Hz) on “T1” Power Input Terminal.14AWG at terminals 1 thru 4 on Accessory Terminal .18AWG at terminals 22 thru 25 on “T1” Power Input Terminal.

Frame Reinforcement Table Technical Data

120VAC, 60Hz

.6 amps

24 V DC, max. 1.1 Amp.

28 - 48" (71-122 cm)

100-250 lb. (45-113 kg)

Input power:

Power consumption:

Power supply:

Door width:

Door weight:

Door opening angle:

Hold open time: 5 - 30 seconds (A.D.A. 5 seconds min.)

3 ampsCircuit breaker:

up to 110° Pull side; up to 170 Push side;Manually to 180° Push/Pull side

°

General 2Frame Reinforcement Table / Technical Data 2Component Layout 3ADA / ANSI / UL 3Stop (Push) Side Mounting 4Adjust Power and Opening / Closing Cycle 7Input Power Configuration 8

Final Setup 8Inverter Details 9Accessory / Typical Installations 10Troubleshooting 10RF Receiver Setup 12RH Door Template 14LH Door Template 15


ASSA ABLOY

80-9357-0005-020 ( )06-15

BACKPLATE

REED SWITCH

CHAINOPEN / CLOSE POSITIONING MAGNETS

“T1” POWER INPUTTERMINAL (3-POSITION)

ACCESSORYTERMINAL(4-POSITION)

PINION EXTENSION / CLUTCH ASSEMBLY

INVERTER

MOTOR ASSEMBLY

POWER SWITCH

BREAKER SWITCH

1600 SERIES CLOSER BODY

Component Layout

ADA / ANSI / UL InformationAmericans With Disabilities Act (A.D.A.)These door operators can be installed and adjusted to conform with A.D.A. regulations.

ANSI StandardsANSI A117.1 – These door operators permit door assemblies to conform to the requirements of this specification "for buildings and facilities – providing accessibility and usability for physically handicapped people".

• ANSI A156.19 – These products are designed to conform to this specification "for power assist and low energy power operated doors".

U.L. Listing Underwriters Laboratories, Inc. listed for use on

fire and smoke barrier door assemblies when the 120VAC (60Hz) power input is supplied through the normally closed alarm contacts of a compatible UL Listed alarm system or alarm panel.

RF RECEIVER

Optional Mounting Support

Storefront Bracket5700SFB

Transom Angle Bracket5730TAB

CONNECTING LINKBUSHING ASSEMBLY

SHOE

SHOE / ADJUSTING ROD ASSEMBLY

FOREARMSCREW

MAIN ARM

ADJUSTINGTUBE

MAIN ARM / SLIDEUNIT ASSEMBLY

Included with 5730 and 5740


ASSA ABLOY

80-9357-0005-020 ( )06-15

1. Stop (Push) Side - Initial Frame Holes

AB

7/8(22)

3/8(10)

FrameRabbet

Left hand door illustrated.A. Using template, locate and

prepare holes in the frame.B. Drill #7 and tap 1/4-20 Machine

Screws or Self-Drilling Screws (2 places).

* This dimension will be on oppositeside of hinge centerline shown below.

CLof Hinge

Door OpeningAngle

Up to 110°110° to 180°

A

1-9/16 (40)-15/16 (-24) *

B

29-3/16 (741)26-11/16 (678)

RH DoorLH Door

BA 3/8

(10)

7/8(22)

CL of Hinge

LH Door shown (RH Door opposite)

LeftHandDoor

RightHandDoor

2. Stop (Push) Side - Initial Wall PrepFor wood or masonry framing, blocking (supplied by others) is required for proper support of operator. Thickness is dependent upon Frame Return. Material must comply with local codes. Failure to properly support top portion of operator will void warranty.A. For wood framing, screw blocking

into wall studs.B. Lab anchoring required for

masonry walls.

5-1/2”(140)

Frame ReturnC

D

FrameRabbet

CLof Hinge

BlockingMaterial

Up to 110°110° to 180°

C max

4-3/4 (121)2-1/4 (57)

D min

16-1/8 (410)13-5/8 (346)

If above Step 2 for Initial Wall Prep is not available, shown to the right are two options:- Transom Angle Bracket- Storefront Bracket

Optional TransomAngle Bracket

Optional StorefrontBracket

Please verify desired mounting requires Stop (Push) Side

application as shown on this template.


ASSA ABLOY

80-9357-0005-020 ( )06-15

3. Stop (Push) Side - Unit MountingA. Install (2) 1/4-20 x 1” machine screws or 1/4” self-

drilling screws into holes drilled in Step 1. Leave 1/8” gap between bottom of screw head and frame.

B. i)Install Unit Assembly over screws in previous step and ii) slide Unit Assembly toward Latch edge of door.

i

ii

i

ii

i

ii

i

ii

C. Secure (2) screws.

Note: Level is incorporated into back plate to aid in installation.

mounting hold of the door closer body.E. Support behind back plate is required (see

Step 2). If using Storefront or Transom Bracket, LH door will use 1/4-20 x 3/8 flat head screw between closer body and motor; RH door will use (2) 1/4-20 x 3/8 screws for top support holes.

RH DoorLH Door

RH DoorLH Door

ConcealedWiring Holes

ConcealedWiring Holes

Shorter Screwif using Storefront orTransom bracket

4. Stop (Push) Side - For Concealed Wiring OnlyA. Mark conduit holes using back plate as template.B. Remove back plate.C. Drill (2) Ø7/8” holes.

D. Install conduit in frame, if desired.E. Reinstall back plate and secure (2) screws.

5. Stop (Push) Side - Remaining Mounting Screws

A. Using Back Plate as template, locate and prepare holes in the frame.

B. Drill #7 holes and tap 1/4-20 for Machine Screws or Self Drilling Screws (7 places).

C. Install 1/4-20 x 1” machine screws or 1/4” self-drilling screws into holes unless noted otherwise.

D. Flat head screw must be used to go through the

Shorter Screwif using Storefront orTransom bracket


ASSA ABLOY

80-9357-0005-020 ( )06-15

6. Stop (Push) Side - For Surface Wiring OnlyA. Connect wiring conduit to holes in side of back

plate.B. When installing cover, appropriate

knockout will need to be removed.

7. Stop (Push) Side - Prep Door for Arm ShoeA. Using template,

locate and prepare holes in door.

B. Drill 3/8” thru (2 places) for sex bolts.

CLof Hinge

1-3/4(44)

E

RH Door shown(LH Door opposite)1-11/16

(43)

FrameRabbet

3/8 Dia.Sex Nuts(3 Places)

8. Stop (Push) Side - Mount Arm Shoe to Door

LH Door shown(RH Door opposite)

3/8 Dia.Sex Nuts(2 Places)

1/4-20 x 1” Flat Head Screw

A. Place sex nuts through back side of door.B. Attach arm to door using 1/4-20 x 1”

screws.

9. Stop (Push) Side - Attach Arm to CloserA. Install main arm onto pinion shaft

of unit at a 90° angle to the door frame. Align arm mark “S” with the flat corner of the pinion shaft square (see figure 1 at right).

B. Secure main arm to pinion with 1/4-20 Flange Head Screw provided (see figure 2 at right). Tighten screw with 7/16” wrench or socket.

Door OpeningAngle

Up to 110°110° to 180°

E

12 (305)9-1/2 (241)

R

LY

S

Z

Arm Mark

Pinion Flat

Figure 1

Figure 2

FlangeHeadScrew


ASSA ABLOY

80-9357-0005-020 ( )06-15

9. Stop (Push) Side - Attach Arm to Closer Cont.

Power Adjustment

1/8"HexKey

IncreasePower

DecreasePower

10. Stop (Push) Side - Adjust Closing PowerA. Adjust closing power of unit (See illustration at

right) - Using a 1/8” allen wrench, turn the power adjustment shaft clockwise to increase door closing power. Door control is shipped set at midpoint of power setting. Maximum closing power can be achieved with 8 (360°) clockwise turns of the power adjustment screw.

1A. Installation Sequence ContinuedTable 1 - Minimum Opening / Closing Times for ANSI/BHMA A156.19Door Weight in Pounds (kg)Door Leaf

Width -Inches (mm)

Matrix values are in seconds.

Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1.

Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1.

11. Stop (Push) Side - Adjust Closing Power

1/8"HexKey

SlowerClosing

FasterClosing

Closing Cycle

Closed

10°

egnaR hct aL

egnaR peewS

1/8"HexKey

IncreaseCushion

DecreaseCushion

Opening Cycle

Backcheckgninep

O

A. Adjust Hydraulic valves using a 1/8” hex wrench to obtain proper door closing speeds. See following illustrations.

B. Refer to Table 1 below for recommended minimum opening / closing times per ANSI/BHMA A156.19.

Closing Cycle – Make adjustments, as necessary, to the Sweep Speed "S" valve and Latch Speed "L" valve. Note: A.D.A. requires that from an open position of 70°, the door will take at least 3 seconds to move to a point 3” (75mm) from the latched position, measured at the leading edge of the door.

Opening Cycle – Adjust Backcheck, "B" valve, as necessary, for hydraulic resistance to door opening in the backcheck range. Note: Too much Backcheck, "B" valve, can affect the operation of the units pump, preventing units from fully opening the door. This valve may require fine tuning after all other adjustments have been made.Sweep Valve

Latch ValveBackcheck Valve

SpringAdjust

Figure 3Adjusting

Rod

ArmSlide

DoorShoe

MainArm

C. PRELOAD ARM (see figure 3 at right): Remove 1/4-20 hex head screw on adjusting rod and insert adjusting rod into arm slide. Reinstall 1/4-20 screw and leave loose. Rotate main arm away from hinge edge until adjusting rod and arm are perpendicular (at a 90 ° angle) to the doo rframe. Tighten the 1/4-20 hex head screw on the adjusting rod to secure arm in this new position.


ASSA ABLOY

80-9357-0005-020 ( )06-15

13. Final Electrical and Mechanical SetupA. Confirm all mechanical adjustments have been made

and wiring connected per Page 7 and 8.B. Turn on facility’s main circuit breaker.C. Turn power to unit on at the Unit Power Switch and

turn the Breaker Switch to “RESET”.

D. Using a short jumper cable, jump terminals 1 and 2, see Fig. 2 below, to activate unit. When door reaches 20°, switch Breaker Switch to “OFF” position cutting power to the unit. Allow door to fully close (door may be manually pulled closed).

Breaker Switch

Unit Power Switch

1234

1234

Figure 2Figure 1

Low VoltageControlWiring

IncomingPower

12. Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING

Ground Wire Connection – Ground wire must be secured to backplate under head of (green) ground screw nearest to “T1” Power Input Terminal. Screw labeled “GND”.

Terminal Description

HOT

25

23

24

22

COM Common power lead

Hot power lead

Circuit Breaker

Switch

Circuit Breaker

Common connection to Circuit Breaker / Inverter

Thread conduit fitting(s) into backplate as shown. A second conduit fitting is required for low voltage control wiring. CHECK LOCAL CODES. Pull conduit out of header and attach to conduit fittings before mounting. Secure operator to door frame. Attach incoming ground wire to backplate with ground screw as illustrated in “Surface Wiring” illustration to the Right.

Thread conduit fitting(s) into backplate as shown. A second conduit fitting is required for low voltage control wiring. CHECK LOCAL CODES. Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame. Attach incoming ground wire to backplate with ground screw as illustrated below.

GroundLead

PowerLeads

GroundScrew(Green)

Conduitby Others(from top)

“T1” PowerInputTerminal

24

23

22

25

HOT

COM

BreakerSwitch

T1 TerminalBlock


ASSA ABLOY

80-9357-0005-020 ( )06-15

13. Final Electrical and Mechanical Setup ContinuedE. Adjust Closing Position Magnet (See Fig. 3) - With

door in the closed position, use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch.

F. Adjust Open Position Magnet - Use fingers to slide

F cont. Open Position Magnet 180° from Open Position Magnet.

G. Flip Breaker Switch to “RESET” to turn power on. Jump terminals 1 and 2 (as shown in Fig. 2) to activate door. Note open position of the door. Allow door to close.

H. Use finger to readjust the Open Position Magnet to desired door open position.

I. Repeat Step G to verify door open position. J. Make all connections necessary for any accessories to

the 4-position Accessory Terminal (see Pages 10-11).K. Make necessary adjustments to inverter (see ).

Replace cover and cover screws.

Reed Switch

Closed Position Magnet

Open PositionMagnet

Position Ring

Figure 3

Page 9

Inverter Adjustments:· Based on function

adjustment desired, use table above to determine which POT is to be adjusted.

POT FUNCTIONDESCRIPTION

OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease

M/DLY Motor Delay on Opening CW - IncreaseCCW - Decrease

P1 Closing Speed CW - IncreaseCCW - Decrease

H/O TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease

P2 Opening Speed CW - IncreaseCCW - Decrease

H/O TQMotor Torque at Hold Open Position

CW - IncreaseCCW - Decrease

ON

12

WARNING

120 HIGH VOLT POTENTIAL PRESENT. MAKE SURE POWER IS TURNED OFF DURING

INSTALLATION PROCEDURE.

Dip Switch Settings

1. Door Mounting -

2. Push Recognition -

ON - pullOFF - pushON - activeOFF - inactive

WARNINGElectric

Shock Risk

(Adjustments made in the shaded area should be performed by

Authorized Factory Personnel.)

L2115Y

L1 115/230VAC IN

MOTOR OUT

L2230Y

U

V

W

STATUS LEDS

H/O TQH/O TM

OBSTRSENS

P1

M/DLY P2

16

COM

SNS

COM

PB

K1

K2

11

JMP503

NC

NO

TB501

PU

LL P

US

HSW501

ON

12

Inverter Details


ASSA ABLOY

80-9357-0005-020 ( )06-15

Standard Function with Switches

1

2

3

4

1

2

3

4

Notes:1.Power input to Door

Operator Unit is at “T1” Power Input Terminal (not shown) 120VAC 60Hz.

Wall Switch, CardReader, Key Switch,etc.

1

2

3

4

1

2

3

4Door 1 Door 2

Operation:· Doors are normally closed.· Activating either switch will

open both doors. Door will close after hold open time delay has elapsed.

Wall Switch, CardReader, Key Switch,etc.

Normally Open Momentary dry contacts

Normally Open Momentary dry contacts

Radio Frequency Function Option

1 2 3 4

1 2 3 4

Optional Door 2

1 2 3 4

1 2 3 4

Door 1

Notes:1.Power input to Door Operator

Unit is at “T1” Power Input Terminal (not shown) 120VAC 60Hz.

2. Radio Frequency Feature can be purchased as a separate kit.

Operation:· Door is normally

closed.· Activating wireless

switch or hand held wireless transmitter will open the door.

· Door will close after hold open delay elapses.

120VAC

GroundC

OM

HO

TL N(AC) -V +V ADJ

+

1.1A 24V Power Supply12-24 VA

C/D

CC

OM

NO

NC

Troubleshooting

Jump activation input

Change the setting of the ON/OFF switch

Flip Door Mounting Dip Switch to other direction

Remove object

Re-time and re-install arm.

Increase spring tension per preceding instructions

Remove object

Fault Possible reasons why Remedies/Explanations

The door does not open- The motor does not start

Control switch is set to OFF position

Electrical power is missing the electrical Check power switch

Activation unit does not function- The motor starts Motor is driving in wrong direction

Something jammed beneath the door

Arm has come loose

The door does not close Spring tension too lowArm has come loose Re-time and re-install arm.

Something jammed beneath the door

Circuit breaker is set to OFF position Reset circuit breaker to the ON position


ASSA ABLOY

80-9357-0005-020 ( )06-15

Fail Secure / Fail Safe Electric Strike Wiring

120VACSupplied byOthers- +

DC or ACOutput

AC

or

DC

Ele

ctric

Str

ike+

-

Wall Switch, CardReader, Key Switch,etc.Normally Open Momentary dry contacts

Notes:1.Power input to Door Operator Unit is at “T1”

Power Input Terminal (not shown) 120VAC 60Hz.

2.Unit’s Relay Rating for strike interface: 30VDC @ 1A or 125VAC @ .5A

Operation:· Door is normally closed and latched.· Activating switch will unlock the electric strike and the

door will automatically open. Door will close after hold open time delay has elapsed.

· For Fail Secure Strike - The door will remain locked during power failure.

· For Fail Safe Strike - The door will remain unlocked during power failure.

1

2

3

4

1

2

3

4

JMP503

NC

NO

Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation.

Fail Safe Electromagnetic Lock 24VDC Wiring

1

2

3

4

1

2

3

4

Wall Switch, CardReader, Key Switch,etc.Normally Open Momentary dry contacts

+-24VDC Electromagnetic Lock(Fail Safe)

Operation:· Door is normally closed and latched.· Activating switch will cut power to mag lock and the door will automatically

open. Door will close after hold open time delay has elapsed.· The door will unlock during power failure.

Notes:1.Power input to Door Operator Unit is at “T1”

Power Input Terminal (not shown) 120VAC 60Hz.

2.Unit’s Relay Rating: 30VDC @ 1A or 125VAC @ .5A

Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation.

JMP503

NC

NO

120VAC

GroundC

OM

HO

T

L N(AC) -V +V ADJ+

Optional 1.1A 24V Power Supply


ASSA ABLOY

80-9357-0005-020 ( )06-15

Troubleshooting

Red LEDBlue LED

Antenna Wire

Learnw/o DelayButton

DelayPotentiometer(Time Adjustment)

Learn w/Delay Button

DIP Switch

TerminalStrip

Problem: The LED on my receiver is just flickering and I’m unable to program and/or it won’t work.Solution: You have a push plate stuck or faulty transmitter. Disconnect each push plate until the LED goes out. If LED

does not go out, remove each transmitter battery until it does. Replace the appropriate transmitter.Problem: Receiver intermittently doesn’t receive the transmitter(s) signal.

Solution: You may extend the receiver antenna wire only in multiples of 6-3/4” (171), i.e. 6.75 x 4 = 27” (686) of extended antenna wire.

Removing Transmitter Code(s)

Single Transmitter Code:Ÿ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second).Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted.

All Transmitter Codes:Ÿ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10

seconds).

Push Plate Configuration

1. Before beginning, it is easiest to have already prepared the installation of the push plate.2. Connect the wires from the transmitter to the NO and COM contacts of the push plate’s switch.3. Follow Steps 1 - 4 (Hand-Held Configuration); depress the push plate to activate the transmitter.4. Attach the transmitter to the inside of the electrical box and complete the installation.

Hand-Held Configuration

1. Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 0.5s or 10s hold.

2. Press either Learn w/ Delay Button or Learn w/o Delay Button on the receiver depending on the activation requirements (if delay learn is selected, adjust potentiometer to counterclockwise limit, 0 second delay). Red LED on receiver will flash. After learn cycle is complete, adjust potentiometer to desired delay time (0 - 30 sec).

3. Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter). NOTE: Repeat Steps 2 - 3 to program additional transmitters.

4. To test the system, depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver. This indicates that the relay has been activated.

433MHz Receiver User’s Guide

#2OFFON

Description0.5s Hold Time10s Hold Time

FunctionRelay will remain active 0.5 sec after loss of activation.Relay will remain active 10 sec after loss of activation.

#1OFF

ON

DescriptionPulse Relay

Toggle Relay

FunctionPress the transmitter once and the relay will be active momentarily.Press the transmitter once and the relay output is active indefinitely, press it again and the relay will de-energize indefinitely.

ON

1 2PU

L T

OG

0.5s

1

0s ON

1 2PU

L T

OG

0.5s

1

0sIn Toggle Setting (1-ON), the Hold Time is inactive. Either setting for #2 dip switch will

have the same result.

ON

1 2PU

L T

OG

0.5s

1

0s

0.5 second Pulse Setting

ON

1 2PU

L T

OG

0.5s

1

0s

10 second Pulse Setting

ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.

ŸEnsure compliance with all applicable safety standards upon completion of installation.


ASSA ABLOY

80-9357-0005-020 ( )06-15

This PageLeft Blank


ASSA ABLOY

80-9357-0005-020 ( )06-15

Removable Template - Stop (Push) Side - RH Door

Ÿ Do not scale drawing.Ÿ Right hand door shown.Ÿ All dimensions given in

inches (mm).Ÿ Maximum frame reveal is 1/8”

(3 mm) for this application.

Blo

ckin

gM

ater

ial

7-15

/16

(202

)10-2

1/32

(271

)

11(2

79)

11-1

1/16

(297

)

13-1

3/16

(351

)

14-3

/16

(360

)A

3/8

(10)

7-9/

16(1

92)

13-7

/16

(341

)

13-1

3/16

(351

)

B1-

3/4

(44)

3/8

(10)

7/8

(22)

3/4

(19)

4-3/

8(1

11)

1-11

/16

(43)

7/8

(23)

For

Con

ceal

edW

ired

Uni

ts O

nly

(2 P

lace

s)

C LH

inge

or

Piv

ot

Fram

eS

top/

Sof

fit

Fram

eR

abbe

t

3/8

(19)

1/4-

20 M

achi

ne S

crew

sor

No.

14

Woo

d S

crew

s(9

Pla

ces)

Ø

Sex

Nut

s(2

Pla

ces)

5-1/

4M

in C

eilin

gC

lear

ance

Doo

r O

peni

ngA

ngle

Up

to 1

10°

110°

to 1

80°

A

15-3

/4 (

400)

13-1

/4 (

337)

B

12 (

305)

9-1/

8 (2

41)

11/1

6(1

7)


ASSA ABLOY

80-9357-0005-020 ( )06-15

Removable Template - Stop (Push) Side - LH Door

Doo

r O

peni

ngA

ngle

Up

to 1

10°

110°

to 1

80°

A

15-1

/2 (

394)

13-1

/4 (

337)

Ÿ Do not scale drawing.Ÿ Left hand door shown.Ÿ All dimensions given in inches (mm).Ÿ Maximum frame reveal is 1/8” (3 mm) for this

application.

Blo

ckin

gM

ater

ial

7-15

/16

(202

)

10-2

1/32

(271

)

11(2

79)

11-1

1/16

(297

)

13-1

3/16

(351

)

14-3

/16

(360

)

A

3/8

(10)

7-9/

16(1

92)13

-7/1

6(3

41)

13-1

3/16

(351

)

B1-

3/4

(44)

4-1/

16(1

03)

3/8

(10)

7/8

(22)

3/4

(19)

4-3/

8(1

11)

1-11

/16

(43)

7/8

(23)

For

Con

ceal

edW

ired

Uni

ts O

nly

(2 P

lace

s)

C LH

inge

or

Piv

ot

Fram

eS

top/

Sof

fit

Fram

eR

abbe

t

3/8

(19)

1/4-

20 M

achi

ne S

crew

sor

No.

14

Woo

d S

crew

s(9

Pla

ces)

Ø

Sex

Nut

s(2

Pla

ces)

5-1/

4M

in C

eilin

gC

lear

ance


ASSA ABLOY

80-9357-0005-020 ( )06-15

3000 Highway 74 East • Monroe, NC 28112Tel: (800)438-1951 x4706 • Fax: (800)-338-0965

www.nor tondoorcontrols.com

ASSA ABLOY

This PageLeft Blank

ASSA ABLOYextranet.assaabloydss.com/library/installation... · ASSA ABLOY ... assa abloy

Documents

Transcript of ASSA ABLOYextranet.assaabloydss.com/library/installation... · ASSA ABLOY ... assa abloy

ASSA ABLOY Opening Solutions | Hang- en sluitwerk ...€¦ · ASSA ABLOY Opening Solutions | Hang- en sluitwerk ...

Soluções em Portas Corta-fogo - ASSA ABLOY Brasil€¦ · Institucional | ASSA ABLOY Institucional O Grupo ASSA ABLOY é líder mundial no desenvolvimento e fabricação de soluções

ASSA ABLOY automatic sliding door systems - ASSA ABLOY … · 2018-06-16 · ASSA ABLOY Entrance Systems is a leading supplier of entrance automation solutions for efficient flow

ASSA ABLOY Veiligheidsdeursluiter...Abloy OY PO Box 108 80101 Joensuu,Finland ASSA ABLOY DC700G-FT ∙ ASSA ABLOY deursluiter met CAM-technologie, verleng-de montageplaat en geïntegreerd

ASSA ABLOY sustainability journey 2015

ASSA ABLOY branded door closers

ASSA ABLOY Security Doors - ASSA ABLOY South … ABLOY Securit… · The global leader in door opening solutions ASSA ABLOY Security Doors Technical information and specifications

ASSA ABLOY Baltic AS Hinnakiri 2014-ver2-08.01.14 ABLOY Baltic... · 2014-02-21 · ASSA ABLOY ASSA ABLOY Baltic hinnakiri 2014 ASSA ABLOY, the global leader in door opening solutions

Automatic sliding door system - ASSA ABLOY Entrance...ASSA ABLOY SL510, see Product leaflet 1009788 ASSA ABLOY Frame 74 83 85 6 10 0 22, 40 mm 48 22 48 ASSA ABLOY SL500 48 22 48 ASSA

Assa Abloy: Ironmongery and door furniture...Title Assa Abloy - Group 9: Cylinders Author Specifile On-Line Subject Ironmongery and door furniture Keywords Assa Abloy; cylinders; union;

ASSA ABLOY Hospitality Mobile Access - Afro Exports Ltd - hotel … · 2018-11-13 · ASSA ABLOY Hospitality Mobile Access ASSA ABLOY Hospitality (formerly VingCard Elsafe) has been

Välj rätt lås till ditt hem - ASSA ABLOY Opening …assa.assaabloy.com/Other/assa-se/downloads/broschyrer...2016/12/01 · ABLOY PLM 330 ABLOY PL340N ABLOY PL350N ASSA ABLOY, is

Alukon Assa Abloy - metallbau

Assa Abloy - Group 1: Night Latches & Rim Locksmedia.autospec.com/za/assa-abloy/1night-latch.pdf · Title: Assa Abloy - Group 1: Night Latches & Rim Locks Author: Specifile On-Line

Yale opens doors for Assa Abloy - Yale Forklifts: World ... Stu… · Yale opens doors for Assa Abloy Customer Assa Abloy ... monthly KPI reports and regular ... forklift trucks,

ASSA ABLOY

ASSA ABLOY Dörrhandtag

ASSA ABLOY · ASSA ABLOY ... assa abloy

ASSA ABLOY.pdf · assa abloy

ASSA ABLOY Leading the future ABLOY CMD...© ASSA ABLOY. All rights reserved Agenda 1. Introduction - ASSA ABLOY 2017 2. Finance –Overview 3. Strategy - Our Road to the Future 4.