129304924 Dent Buckle Chart FlottaCL 415 Parte2
-
Upload
akang-harry -
Category
Documents
-
view
20 -
download
0
description
Transcript of 129304924 Dent Buckle Chart FlottaCL 415 Parte2
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DENT AND BUCKLE CHART
Document N°: DBC-CO-002
Revision N° and Date: Rev.00 Apr 04, 11
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 2 of 10 DBC-CO-002 Rev.00 Apr 04, 11
1 Filling & Handling instructions The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1. Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information (dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side : • Item n° : Damage progressive number • Date : Record date of the finding • Description and Dimension : Short description and dimensions of the damage • Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage • T (Temporary) : Report the document issued for handling the deferred action • Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record - For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”. NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO Engineering Department
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 3 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Fuselage LH side
Fuselage upper side
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 4 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Fuselage RH side
Fuselage Bottom side
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 5 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Wing LH upper side
Wing RH upper side
Wing LH Bottom side
Wing RH Bottom side
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 6 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Empennage RH side
Empennage LH side
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 7 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Empennage Upper side
Empennage Bottom side
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 8 of 10 DBC-CO-002 Rev.00 Apr 04, 11
RH Propeller
LH Propeller
L
BLADES FILLING INSTRUCTIONS Underline numbering defect on above assembly to indicate which blade is damaged and report same number on the detailed drawing on the left on specific position.
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 9 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Windows LH View
Windows RH View
DBC-CO-002 Rev.00 Apr 04, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCO
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 10 of 10 DBC-CO-002 Rev.00 Apr 04, 11
Item n° Description & Dimension Date Inspector
Signature Acceptable, Temporary action
and/or Repair Date Inspector Signature
A
T
A
T
A
T
A
T
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
DENT AND BUCKLE CHART
Document N°: DBC-CQ-002
Revision N° and Date: Rev.00 May 18, 11
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 2 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
1 Filling & Handling instructions The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1. Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information (dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side : • Item n° : Damage progressive number • Date : Record date of the finding • Description and Dimension : Short description and dimensions of the damage • Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage • T (Temporary) : Report the document issued for handling the deferred action • Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record - For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”. NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO Engineering Department
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 3 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Fuselage LH side
Fuselage upper side
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 4 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Fuselage RH side
Fuselage Bottom side
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 5 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Wing LH upper side
Wing RH upper side
Wing LH Bottom side
Wing RH Bottom side
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 6 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Empennage RH side
Empennage LH side
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 7 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Empennage Upper side
Empennage Bottom side
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 8 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
RH Propeller
LH Propeller
L
BLADES FILLING INSTRUCTIONS Underline numbering defect on above assembly to indicate which blade is damaged and report same number on the detailed drawing on the left on specific position.
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 9 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Windows LH View
Windows RH View
CL415 - DBC DENT & BUCKLE CHART
DBC-CQ-002 Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415 Page 10 of 10 DBC-CQ-002 Rev.00 Apr 14, 11
Item n° Description & Dimension Date Inspector
Signature Acceptable, Temporary action
and/or Repair Date Inspector Signature
A
T
A
T
A
T
A
T
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DENT AND BUCKLE CHART
Document N°: DBC-CR-002
Revision N° and Date: Rev.00 Jun 03, 11
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 2 of 10 DBC-CR-002 Rev.00 Jun 03, 11
1 Filling & Handling instructions The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1. Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information (dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side : • Item n° : Damage progressive number • Date : Record date of the finding • Description and Dimension : Short description and dimensions of the damage • Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage • T (Temporary) : Report the document issued for handling the deferred action • Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record - For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”. NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO Engineering Department
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 3 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Fuselage LH side
Fuselage upper side
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 4 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Fuselage RH side
Fuselage Bottom side
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 5 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Wing LH upper side
Wing RH upper side
Wing LH Bottom side
Wing RH Bottom side
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 6 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Empennage RH side
Empennage LH side
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 7 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Empennage Upper side
Empennage Bottom side
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 8 of 10 DBC-CR-002 Rev.00 Jun 03, 11
RH Propeller
LH Propeller
L
BLADES FILLING INSTRUCTIONS Underline numbering defect on above assembly to indicate which blade is damaged and report same number on the detailed drawing on the left on specific position.
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 9 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Windows LH View
Windows RH View
DBC-CR-002 Rev.00 Jun 03, 11
CL415 - DBC DENT & BUCKLE CHART Reg. Marks: I-DPCR
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot Page 10 of 10 DBC-CR-002 Rev.00 Jun 03, 11
Item n° Description & Dimension Date Inspector
Signature Acceptable, Temporary action
and/or Repair Date Inspector Signature
A
T
A
T
A
T
A
T