118d8a411e5a416c946533811e5e1912b5cedb18
-
Upload
milenko-tulencic -
Category
Documents
-
view
217 -
download
0
Transcript of 118d8a411e5a416c946533811e5e1912b5cedb18
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
1/11
Data sheet
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.: 100
Quantity: 1 Date: 28/05/2014Page: 1 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Operating data
Design
Driver, accessories
Extension cables designed for installation in open air, laid alonga surface.
Materials Pump C1 - Materials Driver C1
Requested flow rate 25.20 m/h
Requested developed head 68.00 m
Pumped medium Water Clean waterNot containing chemical andmechanical substances which
affect the materialsAmbient air temperature 20.0 C
Fluid temperature 20.0 C
Fluid density 998 kg/m
Actual flow rate 25.20 m/h
Dev. head without non-returnvalve
68.63 m
MEI (Minimum EfficiencyIndex)
0.70
Efficiency without non-return
valve
74.8 %
Power absorbed 6.29 kW
Max. power on curve 6.59 kW
Min. allow. flow for continuousstable operation
11.79 m/h
Min. allow. flow for short termoperation
2.95 m/h
Fluid viscosity 1.00 mm/s
Dev. head with non-returnvalve
68.37 m
Flow velocity around motor 0.2 m/s
Shutoff head 89.53 m
Max. allow. flow rate 39.53 m/h
Design Single system 1 x 100 %
Pump standard Submersible bore hole pumpsDesign Close-coupledOrientation VerticalDesign according to standard Drinking water acc. to ACSConnection standarddischarge
EN 1092-2
Discharge nominal dia. DN 80Discharge norminal pressure PN 40Wear ring Casing/impeller wear ring
Impeller diameter 90.0 mm
Min. fluid level above pump 0.50 m
Non return valve withValve plate drilled NoSuction hood WithoutBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mm
Motor size 150EDesigned for operation withfrequency inverter
No
Motor speed 2882 rpm
Frequency 50 Hz
Rated voltage 400 V
Rated power P2 7.00 kW
Available reserve 13.79 %Rated current 17.1 A
Motor enclosure IP68Cos phi at 4/4 load 0.77
Motor efficiency at 4/4 load 77.2 %
Starting mode Direct-on-line starting
Type of current Three phase (3~)Drinking water filling NoJ2 Winding No
Cable extension Connect extension cable infactory
Short cable F4Short cable cross section 2.50 mm
Length of short cable 4.00 m
Shroud type Without
Suction casing (106) Stainless steel 1.4408
Stage casing (108) Stainless steel 1.4301Pump shaft (211) Stainless steel 1.4305Clockwise impeller (232) Stainless steel 1.4301Bearing carrier (382.51) Stainless steel 1.4301Casing wear ring (502) Nitrile rubber NBR
Impeller wear ring (503) CrNiMo steel 1.4404
Bearing bush (545) Nitrile rubber NBRValve body (751) Stainless steel 1.4408Stator (81-59) Stainless steel 1.4301Motor shaft (819) 1.4021+QTMotor cable (824) CU-rubber
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
2/11
Data sheet
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.: 100
Quantity: 1 Date: 28/05/2014Page: 2 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Nameplates
Nameplates language English
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
3/11
Compact data sheet
Customer item no.:
Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 3 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Design
Materials Pump C1 - Materials Driver C1
Operating data
Driver, accessories
Extension cables designed for installation in open air, laidalong a surface.
Pump standard Submersible bore holepumps
Design Close-coupledOrientation VerticalDesign according to standard Drinking water acc. to ACSConnection standarddischarge
EN 1092-2
Discharge nominal dia. DN 80Discharge norminal pressure PN 40Impeller diameter 90.0 mmMin. fluid level above pump 0.50 mNon return valve withValve plate drilled NoSuction hood WithoutBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mm
Suction casing (106) Stainless steel 1.4408Stage casing (108) Stainless steel 1.4301Pump shaft (211) Stainless steel 1.4305Clockwise impeller (232) Stainless steel 1.4301
Pumped medium Water Clean waterNot containing chemicaland mechanicalsubstances which affect thematerials
Ambient air temperature 20.0 CFluid temperature 20.0 CActual flow rate 25.20 m/hDev. head without non-returnvalve
68.63 m
MEI (Minimum EfficiencyIndex)
0.70
Efficiency without non-return
valve
74.8 %
Power absorbed 6.29 kWDesign Single system 1 x 100 %
Designed for operation withfrequency inverter
No
Motor speed 2882 rpmFrequency 50 HzRated voltage 400 VRated power P2 7.00 kWAvailable reserve 13.79 %Rated current 17.1 AMotor enclosure IP68
Starting mode Direct-on-line startingDrinking water filling NoJ2 Winding NoShort cable F4Short cable cross section 2.50 mmLength of short cable 4.00 m
Shroud type Without
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
4/11
Performance curve
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 4 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
0 5 10 15 20 25 30 35 40[m/h]
40
60
80
[m]
94.0/86.0
Qmin
Qmax
Totaldevelop
edhead
0 5 10 15 20 25 30 35 40[m/h]
0
50
[%]E
fficiency
0 5 10 15 20 25 30 35 40[m/h]
4
5
6
[kW]
PowerInput
Flow
Curve data
Speed of rotation 2895 rpm
Fluid density 998 kg/m
Viscosity 1.00 mm/s
Flow rate 25.20 m/h
Requested flow rate 25.20 m/hRequested developed head 68.00 m
Dev. head without non-return valve
68.63 m
MEI (Minimum EfficiencyIndex)
0.70
Efficiency without non-return valve
74.8 %
Power absorbed 6.29 kW
Curve number UPA150C3050Effective impeller diameter 90.0 mm
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
5/11
Speed curve
Customer item no.:
Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 5 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
0 5 10 15 20 25 30 35 40[m/h]
0
20
40
60
80
100
[m]
2895 1/min
Qmin
Qmax
Totaldeveloped
head
0 5 10 15 20 25 30 35 40[m/h]
0
50
[%]E
fficiency
0 5 10 15 20 25 30 35 40[m/h]
4
5
6
[kW]
PowerInput
Flow
Curve data
Fluid density 998 kg/m
Viscosity 1.00 mm/s
Requested flow rate 25.20 m/h
Requested developed head 68.00 m
MEI (Minimum EfficiencyIndex)
0.70
Effective impeller diameter 90.0 mm
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
6/11
Motor data sheet
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 6 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
0 1 2 3 4 5 6 7 8[kW]
2850
3000
[rpm]
n
0 1 2 3 4 5 6 7 8[kW]
0
20
40
60
80
[kW]
0.0
0.2
0.4
0.6
0.8
[1]
0
20
40
60
80
100
120
140
160
[A]
0
20
40
60
80
[%]
P1
cos phi
I
eta
mechanical power P2
Motor data
Curve data
The no-load point is not a guarantee point within the meaning of IEC 60034
Motor manufacturer KSBMotor size 150EMotor construction type Water-filled suble squirrel-
cage motorRated voltage 400 V
Frequency 50 HzMotor power 7.00 kW
Rated current 17.1 A
Rated speed 2873 rpm
Starting mode Direct-on-line startingCable standard VDESwitching frequency 15.00 1/h
Load 0.0 % 25.0 % 50.0 % 75.0 % 100.0 %
P2 0.00 kW 1.88 kW 3.75 kW 5.63 kW 7.50 kW
n 2980 rpm 2960 rpm 2936 rpm 2906 rpm 2873 rpm
P1 1.30 kW 3.02 kW 5.01 kW 7.26 kW 9.77 kW
I 10.6 A 11.2 A 12.7 A 14.9 A 18.0 AEta 0.0 % 62.1 % 74.9 % 77.5 % 76.8 %
cos phi 0.18 0.39 0.57 0.70 0.78
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
7/11
Installation plan
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 7 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
1122
DN 80
200
1821
Drawing is not to scale Dimensions in mm
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
8/11
Installation plan
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 8 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Motor Connections
Weight net
Connect pipes without stress or strain! For auxiliary connections seeseparate drawing.
Note: The dimensions shownreflect the actual stagenumber. The drawing isonly symbolic.
Motor manufacturer KSBMotor size 150EMotor power 7.00 kWNumber of poles 2Speed of rotation 2882 rpm
Discharge nominal size DN2 DN 80 / EN 1092-2Rated pressure disch. PN 40
shroud 0 kgPump 20 kgMotor, cable 45 kgTotal 65 kg
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
9/11
Connection plan
Customer item no.:Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 9 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
10/11
Text for invitation of tenders
Customer item no.:
Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 10 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Position Quantity Text for invitation of tenders
100 1 UPA 150C-30/8 UMA 150E 7/21Submersible borehole pumpMultistage centrifugal pump for vertical or horizontalinstallation. Intermediate bearing in every stage. Integeratedeays-to-remove anti-jam non-return valve. Suction strainer,drive lantern and valve body made of investment casting. Pre-filled submersible motor. Three-phase squirrel cage motorwith self-aligning thrust bearing and adequately sizedexpansion diaphragm for pressure equalisation. Design incompliance with VDE standards.UPA 150C-30/8 UMA 150E 7/21Pump type UPA 150CPumped medium Water, Clean water Max. fluid temperature 20.0 CTemperature limit forselected material max.
50.0 C
Density 998 kg/mViscosity 1.00 mm/sDev. head with non-returnvalve
68.37 m
Flow velocity around motor 0.2 m/sActual flow rate 25.20 m/hActual developed head 68.63 mPower absorbed 6.29 kWMax. power on curve 6.59 kWMin. allowable flow rate 11.79 m/hShutoff head 89.53 mMax. allow. flow rate 39.53 m/hInstallation type Close-coupledDesign according to standard Drinking water acc. to ACSStage number 8Flange connection Round flangeDischarge flange nominalpressure
PN 40
Discharge nominal dia. DN 80Non return valve withValve plate drilled NoBearing pedestal WithoutMax. outside diameter 200.0 mmTotal length of unit 1821.0 mmFrequency invertor NoMotor speed 2882 rpmFrequency 50 HzOperating voltage 400 VRated input P1 9.07 kWRated power P2 7.00 kWRated current max. 17.1 ASpeed 2895 rpmMotor pole number 2Motor enclosure IP68Cos phi at 4/4 load 0.77Motor starting mode Direct-on-line starting
-
8/11/2019 118d8a411e5a416c946533811e5e1912b5cedb18
11/11
Text for invitation of tenders
Customer item no.:
Communication dated: Number: ES 2982009
Doc. no.: Item no.:100
Quantity: 1 Date: 28/05/2014Page: 11 / 11
UPA 150C-30/8 UMA 150E 7/21 Version no.: 1
Submersible borehole pump
Position Quantity Text for invitation of tenders
Type of current Three phase (3~)Motor efficiency 77.2 %Motor manufacturer KSBDrinking water filling NoCable extension Connect extension cable in
factoryShort cable F4Short cable cross section 2.50 mmLength of short cable 4.00 mShroud type WithoutFinal coating WithoutColor withoutMaterial variant C1Suction casing (106) Material Stainless steel 1.4408Stage casing (108) Material Stainless steel 1.4301Pump shaft (211) Material Stainless steel 1.4305Clockwise impeller (232)Material
Stainless steel 1.4301
Bearing carrier (382.51)Material
Stainless steel 1.4301
Casing wear ring (502)Material
Nitrile rubber NBR
Impeller wear ring (503)Material
CrNiMo steel 1.4404
Bearing bush (545) Material Nitrile rubber NBRValve body (751) Material Stainless steel 1.4408Stator (81-59) Material Stainless steel 1.4301Motor shaft (819) Material 1.4021+QTMotor cable (824) Material CU-rubberShaft seal type Single acting mechanical
sealShaft seal manufacturer KSBShaft seal manufacturer type MSUShaft seal material SIC/SIC/NBR
Shaft seal type UM Mechanical seal motor side
Orientation VerticalManufacturer KSBPricegroup P16