632 South 3rd StreetP.O. Box 2816 � Paducah, KY 42002270-444-0085Fax: 270-443-6180Website: www.matweld.comEmail: customerservice@matweld.com

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

The Matweld Spike Driver is equippedwith torsion dampened handles whichreduce the vibration level to a mini-mum. An excellent heavy duty tool de-signed to drive spikes and hairpins intothe toughest ties in seconds.

01400ASPIKE DRIVER

B

C

A

FLOW

10 GPM(38 LPM)

PRESSURE

2000 psi(140 bar)

DIMENSIONS

A - 30"B - 18"C - 4"

WEIGHT

65 lbs(29.5 kg)

2

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

3

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

GENERAL SAFETY PRECAUTIONS:TOOL OPERATORS AND MAINTENANCE PERSONNEL MUST ALWAYS COMPLY WITH THESAFETY PRECAUTIONS GIVEN IN THIS MANUAL, AND WITH ALL STICKERS AND TAGS AT-TACHED TO THE TOOL AND HOSE. ALL SAFETY PRECAUTIONS ARE GIVEN FOR YOURSAFETY. READ TO UNDERSTAND AND FOLLOW ALL SAFETY, MAINTENANCE AND OPERA-TION INSTRUCTIONS BEFORE YOU USE OR MAINTAIN THE TOOL. REVIEW THE MANUALDAILY BEFORE USING THE TOOL. IN ADDITION, FOLLOW ALL SAFETY GUIDELINES GIVENYOU BY YOUR SUPERVISOR. DO NOT USE THE TOOL IF YOU HAVE ANY QUESTIONS ABOUTTHE OPERATION, SAFETY OR MAINTENANCE OF THIS TOOL. FAILURE TO FOLLOW THESEINSTRUCTIONS CAN RESULT IN PERSONAL INJURY OR EQUIPMENT DAMAGE.MATWELD HAS NO CONTROL OVER TOOL USE OR OPERATION ONCE IT LEAVES THEMATWELD PLANT. MATWELD HAS NO CONTROL OVER OPERATOR OR MAINTAINER SELEC-TION. THE CUSTOMER MUST ASSUME RESPONSIBILITY FOR THE TOOL�S SUITABILITY FORA PARTICULAR FUNCTION, FOR ANYONE USING THE TOOL OR MAINTAINING THE TOOL RE-GARDING THEIR FITNESS TO USE THE TOOL OR REPAIR THE TOOL, UNDERSTANDING OFTHE OPERATION AND SAFETY AND MAINTENANCE MANUAL, INTELLIGENCE TO USE GOODJUDGMENT NECESSARY TO WORK SAFELY AND EFFICIENTLY WITHOUT ENDANGERINGTHEMSELVES OR BYSTANDERS IN THE WORK AREA.� DO NOT OPERATE THE TOOL UNTIL YOU HAVE BEEN THOROUGHLY AND PROPERLY

TRAINED OR UNDER THE SUPERVISON OF AN INSTRUCTOR.� CHECK POWER SOURCE DAILY TO DETERMINE IF CORRECT FLOW AND PRESSURE ARE

AVAILABLE. NEVER EXCEED FLOWS OR PRESSURES FOR THE TOOL BEING USED. PER-SONAL INJURY OR DAMAGE TO THE TOOL CAN RESULT.

� OPERATORS MUST CLEAR THE WORK AREA OF NON-ESSENTIAL PERSONNEL. FLYINGDEBRIS CAN CAUSE SERIOUS INJURY.

� THE OPERATOR MUST BE FAMILIAR WITH ALL PROHIBITED WORK AREAS SUCH AS UN-SAFE GRADES, POOR FOOTING AREAS AND OVERHEAD HAZARDS.

� MAINTAIN BALANCE AND PROPER FOOTING AT ALL TIMES. NEVER OVERREACH TO THEEXTENT THAT A BROKEN PART OR SUDDEN MOVEMENT OF THE TOOL CAN CAUSE YOUTO LOSE YOUR BALANCE AND FALL, OR CAUSE INJURY TO YOUR SELF OR SOMEONEELSE.

4

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

� WHEN WORKING NEAR ELECTRICAL CONDUCTORS, ALWAYS ASSUME THAT THE CON-DUCTORS ARE ENERGIZED AND THAT HOSES AND CLOTHING CAN CONDUCT HARMFULELECTRICITY. USE HOSES LABELED AND CERTIFIED AS NON-CONDUCTIVE.

� DO NOT OPERATE THE TOOL AT EXCESSIVE FLUID TEMPERATURES OPERATOR DIS-COMFORT AND POTENTIAL BURNS CAN RESULT AT HIGH OIL TEMPERATURES.

� NEVER WEAR LOOSE CLOTHING THAT CAN GET ENTANGLED IN THE WORKING PARTSOF THE TOOLS OR BE CARELESS WITH HANDS, FEET OR OTHER BODY PARTS AROUNDTHE WORKING PARTS OF THE TOOLS. HYDRAULIC TOOLS EXERT HIGH TORQUE ANDFORCE AND CAN CAUSE SERIOUS INJURY OR DEATH IF IMPROPERLY USED.

� TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR, MAINTENANCEOR SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINEDPERSONNEL.

� ALWAYS WEAR SAFETY EQUIPMENT SUCH AS OIL INJECTION RESISTANT WORK GLOVES,SAFETY GLASSES, SAFETY BOOTS, EAR PROTECTION AND OTHER SAFETY APPARELDICTATED BY YOUR SUPERVISOR APPLICABLE FOR THE JOB YOU ARE DOING AND THETOOL YOU ARE USING.

� DO NOT CLEAN INSPECT OR REPAIR THE TOOL WHILE CONNECTED TO THE POWERSOURCE. ACCIDENTAL ENGAGEMENT OF THE TOOL CAN CAUSE SERIOUS PERSONALINJURY.

� OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A CONDITION WHEREHYDRAULIC OIL IS INJECTED UNDER THE SKIN FROM PRESSURE IN THE LINE. ALWAYSWEAR GLOVES AND REPAIR ANY LEAKS IMMEDIATELY. NEVER CARRY A TOOL BY THEHOSES.

� DO NOT USE DAMAGED EQUIPMENT. IMMEDIATELY REPLACE ANY DAMAGED HOSES,FITTINGS, OR OTHER COMPONENTS SHOWING WIRE BRAID, NICKS, CUTS, DAMAGE ORABRASIONS. FAILURE TO DO SO MAY RESULT IN EQUIPMENT DAMAGE AND / OR PER-SONAL INJURY OR DEATH.

� CLEAN UP ANY OIL OR FLUID SPILLS IMMEDIATELY.

5

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

HAVE SUPERVISOR ADD ADDITIONAL PRECAUTIONS RELATING TO THE SPECIFICWORK AREA AND LOCAL SAFETY REGULATIONS BELOW:

**********************

6

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

SAFETY PRECAUTIONS:1. ALWAYS WEAR PROTECTIVE EQUIPMENT SUCH AS GLOVES, SAFETY GLASSES, EAR

PROTECTION AND SAFETY SHOES.2. DO NOT WEAR CLOTHING WHICH MAY BECOME ENTANGLED IN THE TOOL.3. ALWAYS KEEP WORK AREA FREE OF TOOLS OR ANY OTHER OBJECTS WHICH MAY IM-

PAIR SOUND FOOTING.4. CAUTION OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A CON-

DITION WHERE THE HYDRAULIC OIL IS FORCED UNDER THE SKIN THROUGH PRES-SURE IN THE LINE. ALWAYS WEAR GLOVES AND REPAIR LEAKS IMMEDIATELY.

5. DO NOT CARRY THE TOOL BY THE PIGTAIL HOSES.6. NEVER ALLOW ANYONE OTHER THAN A PROPERLY TRAINED SERVICE REPRESENTA-

TIVE TO SERVICE ACCUMULATOR. THE ACCUMULATOR IS UNDER HIGH PRESSURE,IMPROPER DISASSEMBLY CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT USE THETOOL OR HOOK TO A POWER SOURCE IF IT APPEARS THAT THE ACCUMULATOR HASBEEN TAMPERED WITH. IMMEDIATELY RETURN THE TOOL TO MATWELD FOR INSPEC-TION AND SERVICE.

7. ALWAYS KEEP A FIRM GRASP ON THE DRIVER, WITH BOTH HANDS, AT ALL TIMES.8. DO NOT LEAN ON THE TOOL WHILE IN OPERATION. THE FAILURE OF THE BIT OR ANY

OTHER PART COULD CAUSE YOU TO LOOSE YOUR BALANCE AND CAUSE SERIOUSINJURY.

9. AVOID FREE BLOWS (THE PISTON DOES NOT HIT THE TOOL), AS THIS WILL LEAD TOUNNECESSARY HEATING OF THE OIL AND IN THE LONG RUN DAMAGE BOTH SEALSAND THE TOOL.

10. TO MINIMIZE THE POSSIBILITY OF ANVIL BREAKAGE, REPLACE ANVIL ANNUALLY ANDINSPECT CASTING FOR CRACKS OR DAMAGE.

11. DO NOT �DRY FIRE� THE TOOL. ALWAYS SET THE SPIKE DRIVER ON THE SPIKE BEFOREPULLING THE TRIGGER.

01400A SPIKE DRIVER

7

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVER

FLOW: 10 GPM (38 LPM)PRESSURE: 2000 PSI (140 BAR)BACKPRESSURE: 150 PSI (10 BAR) MAXIMUMWEIGHT: 65 LBS.

OPERATION:1. WITH THE POWER SOURCE IN THE �OFF� POSITION, CONNECT THE HOSES. DO NOT

DRAG THE SERVICE HOSE BY PULLING WITH THE TOOL. LOOP THE SERVICE HOSEIN THE WORK AREA IN SUCH A WAY TO RELIEVE STRESS ON THE HOSE AND QUICKDISCONNECT FITTINGS WHILE WORKING. BE AWARE OF HOSE LOCATION AT ALLTIMES.

2. CONNECT THE TOOL TO THE POWER SOURCE.3. TURN THE POWER SOURCE �ON� TO SUPPLY 10 GPM TO TOOL.4. MAKE SURE SPIKES THAT ARE TO BE DRIVEN ARE SECURELY SET.5. THE TOOL MUST BE PLACED ON TOP OF A SPIKE BEFORE DEPRESSING THE TRIG

GER.6. RELEASE THE TRIGGER WHEN THE TOOL IS BEING REPOSITIONED TO ANOTHER

WORK AREA.7. PARTIALLY DEPRESSING THE TRIGGER OR SETTING FLOW ON 5 GPM WILL ALLOW

THE TOOL TO RUN AT SLOWER SPEEDS.8. TURN THE POWER SOURCE �OFF� BEFORE DISCONNECTING TOOL.

8

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERMAINTENANCE:1. CHECK TOOL FOR OVERALL WORKING CONDITION DAILY.2. INSPECT HOSES DAILY. AT THE FIRST SIGN OF ANY ABRASION OR CUT TO THE COVER,

THE HOSES MUST BE CHANGED.3. KEEP QUICK DISCONNECT COUPLERS CLEAN & LUBRICATED.4. USE ONLY RECOMMENDED HYDRAULIC OILS. NEVER USE ATF OR MOTOR OIL.SUGGESTED HYDRAULIC OILS:AMOCO RYKON MV BEL-RAY RAYLENE LT-20SUN 2105 MOBIL D.T.E. 15CHEVRON EP-MV TEXACO �RANDO� HD-AZ

IF YOUR LOCAL DISTRIBUTOR DOES NOT CARRY ANY OF THE ABOVE SUGGESTED HY-DRAULIC OILS USE THE FOLLOWING GUIDELINES:VISCOSITY @ 100° F�����������������100-190SUSVISCOSITY INDEX������������������MIN.150EACH APPLICATION IS DIFFERENT, IF THERE ARE ANY QUESTIONS CONCERNING THERIGHT CHOICE FOR YOUR PARTICULAR APPLICATION CALL MATWELD FOR ASSISTANCE.

5. HAVE TOOL INSPECTED, AT LEAST ANNUALLY, BY A MATWELD OR MATWELD QUALI-FIED SERVICE REPRESENTATIVE TO DETERMINE IF TOOL IS IN NEED OF SAFETYCHANGES OR WORN PART REPLACEMENT.

6. CONTACT MATWELD ON A PERIODIC BASIS, AT LEAST ANNUALLY, FOR SERVICE BUL-LETINS, SAFETY NOTICES, OR OTHER IMPORTANT INFORMATION PERTAINING TOTHIS TOOL.

7. INSPECT ANVIL EVERY SIX MONTHS FOR WEAR, CRACKS, OR MUSHROOM CONDITION. SERVICE NOTE: IF ANVIL BREAKS IN SERVICE, CONTINUED USE OF TOOL WILL BREAKNOSE CASTING.

9

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVER

REPAIR TROUBLESHOOTING:1. SPIKE DRIVER CYCLES OK BUT LACKS POWER� ACCUMULATOR NEEDS RECHARGING.NITROGEN RECHARGE TO 50 BAR,

(725 PSI).� REPLACE WORN OR MUSHROOMED ANVIL.2. SPIKE DRIVER DOESN�T CYCLE WHEN TRIGGER IS DEPRESSED� DIRT IN SPOOL VALVE, REVERSE PIGTAILS AND CYCLE APPROXIMATELY 30

SECONDS UNDER POWER TO FLUSH DIRT OUT OF SPIKE DRIVER. REINSTALLPIGTAILS CORRECTLY, WITH FLOW GOING TO PORT MARKED �P�.� TO TEST, REMOVE TOP TWO SPRING PINS AND SEE IF DRIVER WILL CYCLE. IFDRIVER WILL CYCLE REPLACE ALL FOUR SPRING PINS.

3. SPIKE DRIVER CYCLES TOO SLOW� BACKPRESSURE EXCEEDS 250 PSI AT TOOL RETURN PORT. CORRECT SYS-TEM BACKPRESSURE PROBLEM FOR PROPER OPERATION. OPTIMUM BACK-PRESSURE AT TOOL RETURN PORT SHOULD BE 150 PSI OR LESS.

4. ANVIL IS BROKEN� INSPECT LOWER TUBE FOR DAMAGE, AS BROKEN ANVIL WILL USUALLY DAMAGE LOWER HOUSING.

5. TRIGGER IS PRESSURIZED� CHECK RETURN COUPLER FOR OBSTRUCTION.6. VALVE HOUSING BOLTS ARE BROKEN� RETORQUE BOLTS TO 52 FT LBS. OVER TIGHTENING WILL CAUSE BOLT FAILURE.

10

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERGENERAL NOTES:

11

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

REVIEW OF HYDRAULIC PRINCIPLES

A. TOOL CIRCUIT

1. HYDRAULIC FORMULAS:

CID X RPM GPM X PSI GPM = 231 HP = 1714 (.85)

1456.9Example: HP required to deliver 10 GPM at 1500 PSI.

10 GPM X 1500 PSI = 15000 = 10.3 HP1456.9 1456.9

(subtract back pressure for tool HP)Estimated HP delivered by pump or used by tool.

PSI GPM 500 1,000 1,500 2,000 2,500 3,000 3 1.03 2.06 3.09 4.12 5.15 6.18 5 1.72 3.43 5.15 6.86 8.58 10.30 10 3.43 6.86 10.3 13.70 17.20 20.60 15 5.15 10.30 15.40 20.60 25.70 30.90

2. BACK PRESSUREBACK PRESSURE MEASURED AT THE TOOL RETURN PORT MUST NOT EXCEED THE MANU-FACTURERS BACK PRESSURE RATING. MOST MANUFACTURERS LIST THE MAXIMUM BACKPRESSURE FOR THEIR HYDRAULIC TOOLS AT 250 PSI. BACK PRESSURE MEASURED ONTHE RETURN SIDE OF THE TOOL IS THE FORCE REQUIRED TO GET THE OIL BACK TO THETANK. IN ALMOST ALL CASES THE LOWER THE BACK PRESSURE THE BETTER THE TOOLPERFORMANCE. FIRST, THE BACK PRESSURE IS SUBTRACTED FROM THE MAXIMUM TOOLPRESSURE TO ARRIVE AT A MAXIMUM TOOL OPERATING PRESSURE. FOR EXAMPLE, TOOLSWITH 2000 PSI OPERATING PRESSURE ARE INSTALLED ON A SYSTEM WITH 250 PSI BACKPRESSURE. THIS LEAVES 1750 PSI AS A MAXIMUM TOOL PRESSURE. IMAGINE A SYSTEMWITH 500 PSI BACK PRESSURE. 2000 MINUS 500 PSI BACK PRESSURE LEAVES ONLY 1500PSI FOR THE TOOL. SECOND, TOOLS ARE DESIGNED FOR PRESSURE TO BUILD ON THEPRESSURE SIDE OF THE TOOL. IF TOO MUCH PRESSURE BUILDS ON THE RETURN SIDE,NOT ONLY IS PERFORMANCE EFFECTED, BUT SEALS MAY BLOW. THIS IS WHY IT IS VERYIMPORTANT TO DIRECT THE FLOW INTO THE TOOL CORRECTLY. REVERSING THE HOSESTO TEST MAY RESULT IN BLOWN SEALS, DAMAGE TO THE TOOL, AND PERSONAL INJURY.

12

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400ASPIKE DRIVER

13

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERPARTS LIST

ITEM NO123456789111213141516171819

PART NO.182005918151131815131181572218207231820216182072218200661820057182073518201351820134182006718207121820711182014718201311820148

DESCRIPTION QTY.142421311111111111

TOP COVERSPACER

TABM10X20 SCREWM8 X 35 SCREW

E-HANDLE FRAMEM8 NUT

THRUST PAD W\SCREWTRIGGER LEVER

M8-HEX13 NUT CAPRUBBER HANDLERUBBER HANDLE

DAMPING ELEMENTROLL PIN DIA. 6 X 24

PIN F/PAWL DIA. 6 X 30PIN LATCH RIGHTTRIGGER PAWLPIN LATCH LEFT

14

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVER

15

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERPARTS LIST

ITEM NO. PART NO. DESCRIPTION QTY.111114144121141111231211111712211111112111111111111114211

18137101813103181470918141021814052181772018201011820703181472318201201820702182011718201161815735182004218207051820704610008418177571813141182070618207021820119182011818201151820718182071718147331820211180571418.05.711182023118147021805503181412018207261814701181471218147321820700182010818201361820137182072518207261814749182006518201761820167182072718207081820740181811818207420081600145

PROTECTIVE CAPCHARGING SCREW

SEAL RINGACCUMULATOR COVER

DIAPHRAGMSCREW M10 X 30

ACCUMULATOR BODYO-RING

M10X35 SCREWSPOOL SOCKET

O-RINGAUXILIARY SPOOL

SPOOLBACK-UP WASHERVALVE HOUSING

O-RINGO-RINGO-RINGO-RING

04 KRG FITTINGO-RINGO-RING

GUIDE SOCKETREVERSING SPOOL

SCREWSEAL RING

BALL / CHECK VALVE02 KRG FITTING

STRIKING PISTONSEAL RING

½� NPT HEX NIPPLENOSE CASTING

O-RINGSEAL

PACKING GLANDO-RING

BACK UP RINGSEEGER SPRING RINGSEEGER SPRING RING

SIM PS8X14X0.5TRIGGER SPOOL

TRIGGER RODSPRINGO-RINGO-RINGO-RING

CYLINDERSEAL

BACK-UP WASHERLOCK RING

SEALLOCKING

ANVILROLL PIN 10X60PIGTAIL HOSE

QUICK DISCONNECT COUPLERQUICK DISCONNECT NIPPLE

20212223242526

*27*2829

*30*31323334

*35**36**37**38*39

*40**41*42434445464748495051

*52**53*54

*55**56*575859606162

*63**64**65*66

*67**68*69707172737475

16

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVER

DECAL LEGEND:

17

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

LIMITED WARRANTYMATWELD, INC., PADUCAH, KY., WARRANTS TO THE ORIGINAL PURCHASE OF THIS PROD-UCT THAT THE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIPFOR THE PERIOD OF ONE (1) YEAR AFTER THE DELIVERY OF SUCH PRODUCT TO THECUSTOMER. OTHER EQUIPMENT AND PARTS USED, BUT NOT MANUFACTURED BY MATWELDINC. ARE COVERED DIRECTLY BY THE WARRANTY OF THE MANUFACTURER OF THOSEPRODUCTS. PROOF OF PURCHASE MUST BE DOCUMENTED INCLUDING REFERENCE TO ASERIAL NUMBER LOCATED ON EACH TOOL. THE PURCHASER�S ONLY REMEDIES UNDERTHIS LIMITED WARRANTY SHALL BE LIMITED AT MATWELD�S SOLE OPTION TO THE FOL-LOWING: REPAIR, REPLACEMENT OR REFUND OF THE PURCHASE PRICE OF THE DEFEC-TIVE PRODUCTS. EACH OF THESE REMEDIES REQUIRES TIMELY NOTIFICATION OF THEDEFECT IN THE PRODUCT AND SUBSTANTIATION THAT THE PRODUCT HAS BEEN PROP-ERLY STORED, MAINTAINED AND USED. MATWELD�S OBLIGATIONS HEREUNDER EXTENDONLY TO THE PURCHASER OF THE PRODUCT AND NOT TO ANY THIRD PARTY.AS A CONDITION PRECEDENT TO MATWELD�S OBLIGATION HEREUNDER, THE DEFECTIVE PROD-UCT MUST NOT HAVE BEEN ALTERED OR MODIFIED WITHOUT THE EXPRESS WRITTEN AP-PROVAL OF MATWELD, INC. THE PRODUCT MUST NOT HAVE BEEN SUBJECTED TO DELIBER-ATE DAMAGE, SHIPPING DAMAGE, NEGLECT, TAMPERING BY UNAUTHORIZED PERSONNEL ORDAMAGE BY IMPROPER USE, STORAGE OR MAINTENANCE. SERIAL NUMBERS MUST NOT HAVEBEEN ALTERED, DEFACED OR REMOVED. SUCH ACTION VOIDS LIMITED WARRANTY.

EXCLUSIONS TO LIMITED WARRANTYTHIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRIT-TEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIEDWARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.LIMITED WARRANTY DOES NOT COVER NORMAL WEAR AND TEAR ITEMS SUCH AS FIL-TERS, HOSES, COUPLERS, BITS, SOCKETS, AUGERS, AND BATTERIES.

LIMITATION OF LIABILITYEXCEPT AS PROVIDED ABOVE, MATWELD SHALL IN NO EVENT BE LIABLE OR RESPONSIBLEFOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL, ARISINGOUT OF THE USE OR MISUSE OR INABILITY TO USE THE PRODUCT, HOWEVER CAUSEDAND ON ANY THEORY OF LIABILITY INCLUDING, WITHOUT LIMITATIONS, BREACH OF CON-TRACT, TORT, (INCLUDING NEGLIGENCE OR STREET LIABILITY) AND NOT WITHSTANDINGANY FAILURE OF ANY REMEDY HEREIN OF ITS ESSENTIAL PURPOSE, EVEN IF MATWELDWAS AWARE OF THIS POSSIBILITY OF SUCH DAMAGE. MATWELD�S LIMITED WARRANTY ASSET FORTH ABOVE SHALL NOT BE ENLARGED, DIMINISHED OR AFFECTED BY, AND NOOBLIGATION OR LIABILITY SHALL ARISE OR GO OUT OF THE RENDERING OF TECHNICALADVICE OR SERVICE BY MATWELD OR ITS AGENTS. THE FOREGOING MAY NOT BE CHANGEDEXCEPT BY WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICER OF MATWELD,THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE.

18

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERGENERAL NOTES:

19

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

01400A SPIKE DRIVERGENERAL NOTES:

20

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

04/00

CUSTOMER INFORMATION:Name _____________________________________________________Company___________________________________________________Serial # of your Matweld tool___________________________________( Upon receiving your Matweld tool, make sure to list serial number above so that a good record is kept fororder information.)

MATWELD HYDRAULIC TOOL LISTAll Matweld Hydraulic Tools operate at

5 or 10 GPM @ 2000 PSIPOWER UNITS:70700 � HYDRA POWERED MODULAR SYSTEM02900 � DIESEL 1-10 GPM OR 2-5 GPM

(OPTIONAL CATALYTIC EXHAUST AND/OR MSHA CERTIFIED)00100 � GASOLINE 1-10 GPM OR 2-5 GPM02050 � GASOLINE 1-5 GPM

TRACK TOOLS:01600A � 1� IMPACT WRENCH04500D � ½� IMPACT DRILL00800A � 16� RAIL SAW03900A � REVERSING RAIL SAW01100 � SPIKE PULLER01300A � TIE TAMPER01400 � SPIKE DRIVER01500 � RAIL DRILL01000 � CHAIN SAWGRINDERS:04600 & 04650� STRAIGHT STONE CW & TRIGGER VERSION04700 & 04750 � STRAIGHT STONE CCW & TRIGGER VERSION04800 & 04850 � CUPSTONE & TRIGGER VERSION00700 � RAIL SURFACING GUIDE04300 & 04350 � 6� PROFILE & TRIGGER VERSION02400 � 10� OR 14� FROG AND SWITCH GRINDEROTHER PRODUCTS:HYDRAULIC MANIFOLDSHYDRAULIC TEST GAUGESHOSE REELSHYDRAULIC HOSESACCESSORIES