SCTX SCTX WOODWORKERS WOODWORKERS

CLUBCLUBPOWER EQUIPMENT POWER EQUIPMENT

USAGE MANUALUSAGE MANUAL

SEPTEMBER 2008

2

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITE

CLICK ON “Woodshop Information”

http://www.sctxwoodshop.com/

3

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

CLICK ON“POWER

EQUIPMENT USAGE MANUAL”

LINK

4

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITE

• You will have to have Adobe You will have to have Adobe Reader 8 or higher.Reader 8 or higher.

• Be patient – the file will take Be patient – the file will take from 30 seconds to 2 minutes from 30 seconds to 2 minutes or more to open.or more to open.

http://www.sctxwoodshop.com/

5

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

CLICK ON“BOOKMARK”

ICON

6

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

7

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

SCROLL DOWN TODESIRED SECTION

8

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

HIGHLIGHT SECTION

WITH LEFT CLICK

9

ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/

RIGHT CLICK AND

HIGHLIGHT “Print Page(s)”

TO PRINT SELECTED SECTION

10

ORGANIZATION OF ORGANIZATION OF MANUALMANUAL

Section 1:Section 1: Introduction Introduction Section 2:Section 2: General safety rules General safety rules Section 3:Section 3: Additional resources Additional resources

•in the Woodshop and in the Woodshop and •externalexternal

Section 4:Section 4: How to prepare a board How to prepare a boardSections 5 - 30:Sections 5 - 30: Major pieces of Major pieces of equipmentequipment

Section 31:Section 31: Procedures and rules Procedures and rules on Glue-upson Glue-ups

11

TYPICAL INFORMATIONTYPICAL INFORMATION7. SAW, TABLE (10” POWERMATIC 66-TA, DELTA 36-L53L, DELTA 34-806) ...................................................... 21

7.1. SAFETY PRECAUTIONS ............................................................................................................................... 21 7.2. SETUP – TABLE SAW ................................................................................................................................. 23

7.2.1. Changing the Blade ..................................................................................................................... 23 7.2.2. Blade Raising and Tilting ............................................................................................................. 23 7.2.3. Installing Splitter Guard Assembly .............................................................................................. 24 7.2.4. Miter Gauge Adjustment............................................................................................................. 24 7.2.5. Conditions Which Can Cause Kickbacks ....................................................................................... 24

7.3. SAFETY DEVICES ....................................................................................................................................... 25 7.4. FEED RATE .............................................................................................................................................. 26 7.5. RIP CUTS ................................................................................................................................................ 27 7.6. CROSSCUTS & MITER CUTS ........................................................................................................................ 28

7.6.1. Large Miter Gauge for the Powermatic Saw ............................................................................... 29 7.6.2. Making a Crosscut or Miter Cut ................................................................................................... 30

7.7. BEVEL & COMPOUND ANGLE CUTS .............................................................................................................. 30 7.7.1. Bevel crosscutting ....................................................................................................................... 31 7.7.2. Compound Mitering .................................................................................................................... 31 7.7.3. Bevel Ripping .............................................................................................................................. 31

7.8. DADOS & RABBETS .................................................................................................................................. 31

12

REVISIONSREVISIONS

• Revisions, edits, Revisions, edits, suggestions, etc. are invitedsuggestions, etc. are invited

• Contact Contact sctxwoodshop.manual@suddsctxwoodshop.manual@suddenlink.netenlink.net – Be specific in your emailBe specific in your email– Include name and phone Include name and phone

numbernumber