Post on 17-Feb-2016
21W3KB190÷
21W7KB500
G 3/4 21W3KB190
12 ~ 2
19 140
8 0,2
16 16G 1 21W4KB250 25 190
G 1 1/4 21W5KB350 35 40010 10G 1 1/2 21W6KB400 40 520
G 2 21W7KB500 50 750
Solenoid valve 2/2 way N.C.With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPES:PIPES:
AutomationHeating
G 3/4 - G 2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior
CE Approval(Pressure Equipment Directive 97/23/CE)
for S.V. 21W5÷21W7
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21W3KE190.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
05-06-2015 ODE 21W3KB190 ÷ 21W7KB500
PRESENTATION:PRESENTATION:
Max. allowable pressure (PS) G 3/4 - G 1 23 bar G 1 1/4 - G 2 16 barAmbient temperature:See coils catalogue page for its compatibility.
21W3KB190 G 3/465
105104
21W4KB250 G 1 11221W5KB350 G 1 1/4
98 125 14421W6KB400 G 1 1/221W7KB500 G 2 118 141 172
B 8 14,5 25 30 42 54
21W3KB190 ÷ 21W7KB500 ODE 05-06-2015
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:G 3/4-G 1 Code R990002/BG 1 1/4-G 1 1/2 Code R990005/BG 2 Code R990081/B
5. Complete diaphragm:G 3/4-G 1 Code R450431/BG 1 1/4-G 1 1/2 Code R450466/BG 2 Code R450432/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: E=EPDM V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130KB30-A=2+3KIT:KIT:
G 3/4-G 1KTG0W3KB19=2+4+5G 1 1/4-G 1 1/2KTG0W5KB35=2+4+5G 2KTG0W7KB50=2+4+5
MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm
COILTYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
12-06-2014 (Internal technical data sheet) ODE 21W3KB190 ÷ 21W7KB500 Latching coils
S.V. with pilot control for interception of fluids compatible with theconstruction materials.Opening is obtained by a 50 msec pulse, and closing by another 50 msec pulse, with reversed polarity.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
PRESENTATION:PRESENTATION:
Solenoid valve 2/2 way N.C.With pilot control - Latching coils
21W3KB190÷
21W7KB500Latching coils
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
NoteAvailable on request and withminimum quantities.
PipeISO 228/1 Code Coils code
Voltages
VDC
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar DC bar
G 3/4andG 1
21W3KB190and
21W4KB250
BDA2X006LS 612 ~ 2 19 140 2,5
0,2
16
BDA2X009LS 9BDA2X012LS 12BDA05009LS 9
12 ~ 2 25 190 5BDA05012LS 12BDA05024LS 24
G 1 1/4and
G 1 1/2 andG 2
21W5KB350e
21W6KB400and
21W7KB500
BDA2X006LS 612 ~ 2
35 4002,5
10
BDA2X009LS 9BDA2X012LS 12
40 520BDA05009LS 9
12 ~ 2 5BDA05012LS 1250 750
BDA05024LS 24
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21W3KV190.
USE:USE:
PIPES:PIPES:
COILS:COILS:
AutomationHeating
G 3/4 - G 2
BDA2X006LS 155°C(class F)BDA2X009LS 155°C(class F)BDA2X012LS 155°C(class F)BDA05009LS 155°C(class F) BDA05012LS 155°C(class F) BDA05024LS 155°C(class F)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) G 3/4 - G 1 25 barG 1 1/4 - G 2 16 barAmbient temperature: See coils catalogue page for its compatibility.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C +90°C Air, inert gas, water
E=EPDM(ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C + 140°C Mineral oils (2°E), gasolinegas oil
CE Approval(Pressure Equipment Directive 97/23/CE)
for S.V. 21W5÷21W7
21W3KB190 ÷ 21W7KB500 Latching coils (Internal technical data sheet) ODE 12-06-2014
MATERIALS:MATERIALS:Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Shutter Standard: B=NBR
On request: E=EPDM V=FKMOrifice Brass - UNI EN 12165 CW617NOn request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
SPARE PARTS:SPARE PARTS:
FEATURES:FEATURES:
DIMENSIONS:DIMENSIONS:
AB
+-
+-
Open
CloseABA B
1. Coil:BDA2X006LSBDA2X009LSBDA2X012LSBDA05009LSBDA05012LSBDA05024LS
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:G 3/4 - G 1 Code R990002/BG 1 1/4- G 1 1/2 Code R990005/B
G 2 Cod. R990081/B 5. Complete diaphragm:
G 3/4-G 1 Code R450431/BG 1 1/4 - G 1 1/2Code R450466/BG 2 Code R450432/B
KIT:KIT:KT130KB30-A=2+3
MAINTENANCE KIT:MAINTENANCE KIT:KTG0W3KB19=2+4+5
Type PipeISO 228/1
Amm
Bmm
Cmm
Dmm
Emm
Fmm
21W3KB190 G 3/465
105104
30 42 5421W4KB250 G 1 11221W5KB350 G 1 1/4
98 125 14421W6KB400 G 1 1/221W7KB500 G 2 118 141 172
21W3KB190-MR÷
21W7KB500-MR
G 3/4 21W3KB190-MR
12 ~ 2
19 140
8 0,2
16 16G 1 21W4KB250-MR 25 190
G 1 1/4 21W5KB350-MR 35 40010 10G 1 1/2 21W6KB400-MR 40 520
G 2 21W7KB500-MR 50 750
Solenoid valve 2/2 way N.C.With pilot control - manual operationand closing velocity control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPES:PIPES:
AutomationHeating
G 3/4 - G 2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
28-02-2014 ODE 21W3KB190-MR ÷ 21W7KB500-MR
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notifica
Max. allowable pressure (PS) G 3/4 - G 1 25 barG 1 1/4 - G 2 16 barAmbient temperature: See coils catalogue page for its compatibility.
CE Approval(Pressure Equipment Directive 97/23/CE)
for EV 21W5÷21W7
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21W3E190-MR.
NoteAvailable on request and with minimum quantities.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21W3KB190-MR G 3/465
105104
21W4KB250-MR G 1 11221W5KB350-MR G 1 1/4
98 125 14421W6KB400-MR G 1 1/221W7KB500-MR G 2 118 141 172
B 8 14,5 25 30 42 54
21W3KB190-MR ÷ 21W7KB500-MR ODE 28-02-2014
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: E=EPDM V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube :Code R450603
4. Gasket O-RingCode R990000/B
5. Manual operation:Code R451772/B
6. Gasket O-Ring:G 3/4-G 1 Code R990002/BG 1 1/4-G 1 1/2 Code R990005/BG 2 Code R990081/B
7. Complete diaphragm:G 3/4-G 1 Code R450431/BG 1 1/4-G 1 1/2 Code R450466/BG 2 Code R450432/B
8. Regulation screw:Code R450728/B
KT130KB30-F= 2+3+4KIT:KIT:
KTG0W3KB19= 2+6+7KTG0W5KB35= 2+6+7KTG0W7KB50= 2+6+7
MAINTENANCE KITMAINTENANCE KIT
Type PipeISO 228/1
Amm
Bmm
Cmm
COILTYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
21W3KB190-PC÷
21W4KB250-PC
G 3/4 21W3KB190-PC12 ~ 2
19 1208 0,2 16 16
G 1 21W4KB250-PC 25 150
Solenoid valve 2/2 way N.C.With pilot control - Progressive closing
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests undertaken ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPES:PIPES:
AutomationHeating
G 3/4 - G 1
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
28-02-2014 ODE 21W3KB190-PC ÷ 21W4KB250-PC
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
Max. allowable pressure (PS) 25 bar Ambient temperature:See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21W3KV190-PC.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21W3KB190-PC G 3/465
105104
21W4KB250-PC G 1 112 B 8 14,5 25 30 42 54
21W3KB190-PC ÷ 21W4KB250-PC ODE 28-02-2014
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617N Armature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector
FEATURES:FEATURES:
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube :Code R450606
4. Gasket O-RingCode R990002/B
5. Complete diaphragm:Code R451157/B
5a.Diaphragm-supporting Ring:Code R451228
KT130KB30-A=2+3KIT:KIT:
KTG0W3KB19-PC=2+4+5MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
PRESENTATION:PRESENTATION:
USE:USE:
PIPES:PIPES:
COIL:COIL:
16-09-2015 (Internal technical data sheet) ODE 21W3Z1E190-T5 ÷ 21W4Z1E250-T5
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
21W3Z1E190-T5÷
21W4Z1E250-T5
Solenoid valve 2/2 way N.O.With pilot control - NSF Certified
NoteAvailable on request and with minimum quantities.
AutomationHeating
G 3/4 - G 1
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
For seals other than EPDM replace the letter “E” with the ones corresponding to the other seals. E.I. 21W3ZIV190-T5.
Max. allowable pressure (PS) 23 bar Allowable temperature 82°C Ambient temperature:See coils catalogue page for its compatibility.
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
Gaskets Temperature MediumE=EPDM (ethylene-propylene) - 10°C + 140°C Water
V=FKM (fluoroelastomer) - 10°C + 140°C Mineral oils (2°E),gasoline gas oil
INCAPSULAMENTO E ROCCHETTO SONO REALIZZATICON MATERIALE VERGINE AL 100%.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
G 3/4 21W3Z1E190-T512 ~ 2
19 1408 0,2 16 16
G 1 21W4Z1E250-T5 25 190
21W3Z1E190-T5 ÷ 21W4Z1E250-T5 (Internal technical data sheet) ODE 16-09-2015
DIMENSIONS:DIMENSIONS:
MATERIALS:MATERIALS:
FEATURES:FEATURES:
SPARE PARTS:SPARE PARTS:1. Coil:See coils list
2. Complete diaphragm support:Code R450788/EX1
3. Complete armature tubewithout gasket:Code R450573/D
4. Gasket O-Ring:Code R990000/EX1
5. Gasket O-Ring:Code R990002/EX1
6. Complete diaphragm:Code R450431/EX1/P
Body Low Lead Brass Armature tube Stainless steel AISI series 300 Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: E=EPDM
On request: F=FKMOrifice Low Lead Brass On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector
COILTYPE
POWER ABSORPTION DIMENSIONS
W HoldVA ~
InrushVA ~
Dmm
Emm
Fmm
B 8 14,5 25 30 42 54
Type PipeISO 228/1
Amm
Bmm
Cmm
21W3Z1E190-T5 G 3/465
128104
21W4Z1E250-T5 G 1 113
21W3ZB190÷
21W7ZB500
G 3/4 21W3ZB190
12 ~ 2
19 140
8 0,2
16 16G 1 21W4ZB250 25 190
G 1 1/4 21W5ZB350 35 40010 10G 1 1/2 21W6ZB400 40 520
G 2 21W7ZB500 50 750
Solenoid valve 2/2 way N.O.With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPES:PIPES:
28-02-2014 ODE 21W3ZB190 ÷ 21W7ZB500
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
AutomationHeating
G 3/4 - G 2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) G 3/4 - G 1 25 barG 1 1/4 - G 2 16 barAmbient temperature: See coils catalogue page for its compatibility.
CE Approval(Pressure Equipment Directive 97/23/CE)
for S.V. 21W5÷21W7
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21W5ZE350.
PRESENTATION:PRESENTATION:
21W3ZB190 G 3/465
105104
21W4ZB250 G 1 11221W5ZB350 G 1 1/4
98 125 14421W6ZB400 G 1 1/221W7ZB500 G 2 118 141 172
B 8 14,5 25 30 42 54
21W3ZB190 ÷ 21W7ZB500 ODE 28-02-2014
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: E=EPDM V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
1. Coil:See coils list
2. Complete diaphragm support:Code R450788/B
3. Complete armature tubewithout gasket:Code R450573
4. Gasket O-Ring:Code R990000/B
5. Gasket O-Ring:G 3/4-G 1 Code R990002/BG 1 1/4-G 1 1/2 Code R990005/BG 2 Code R990081/B
6. Complete diaphragm:G 3/4-G 1 Code R450431/BG 1 1/4-G 1 1/2 Code R450466/BG 2 Code R450432/B
KT130ZB30-F=2+3+4KIT:KIT:
G 3/4 - G 1KTG0W3ZB19=2+5+6G 1 1/4 - G 1 1/2KTG0W5ZB35=2+5+6G 2KTG0W7ZB50=2+5+6
MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm
COILTYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
21WA3K0B130 ÷
21WA4K0B130
G 3/8 21WA3K0B13012 ~ 2 13
608 0,2 16 16
G 1/2 21WA4K0B130 70
AutomationHeating
G 3/8 - G 1/2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
USE:USE:
COILS:COILS:
PIPES:PIPES:
Solenoid valve 2/2 way N.C.With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
28-02-2014 ODE 21WA3K0B130 ÷ 21WA4K0B130
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
Max. allowable pressure (PS) 25 barAmbient temperature:See coils catalogue page for its compatibility.
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3K0V130.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3K0B130 G 3/840 97
6021WA4K0B130 G 1/2 66 B 8 14,5 25 30 42 54
21WA3K0B130 ÷ 21WA4K0B130 ODE 28-02-2014
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:Code R990300/B
5. Complete diaphragm:Code R452186/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130KB30-A= 2+3KIT:KIT:
KTGWA3K0B13= 2+4+5MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
12-06-2014 (Internal technical data sheet) ODE 21WA3K0B130 ÷ 21WA4K0B130 Latching coils
S.V. with pilot control for interception of fluids compatible with theconstruction materials.Opening is obtained by a 50 msec pulse, and closing by another 50 msec pulse, with reversed polarity.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
PRESENTATION:PRESENTATION:
USE:USE:
PIPES:PIPES:
COILS:COILS:
AutomationHeating
G 3/8 - G 1/2
BDA2X006LS 155°C(classe F)BDA2X009LS 155°C(classe F)BDA2X012LS 155°C(classe F)BDA05024LS 155°C(classe F)
Solenoid valve 2/2 way N.C.With pilot control - Latching coils
21WA3K0B130÷
21WA4K0B130Latching coils
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3K0V130.
Max. allowable pressure (PS) 20 barAmbient temperature: See coils catalogue page for its compatibility.
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
NoteAvailable on request and with minimum quantities.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C +90°C Air, inert gas, water
V= FKM (fluoroelastomer) - 10°C + 140°C Mineral oils (2°E),gasoline gas oil
PipeISO 228/1 Code Coils code
Voltages
VDC
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar DC bar
G 3/8 21WA3K0B130
BDA2X006LS 6
12 ~ 2 13
602,5
0,2 16
BDA2X009LS 9BDA2X012LS 12BDA05024LS 24 5
G 1/2 21WA4K0B130
BDA2X006LS 6
702,5BDA2X009LS 9
BDA2X012LS 12BDA05024LS 24 5
21WA3K0B130 ÷ 21WA4K0B130 Latching coils (Internal technical data sheet) ODE 12-06-2014
1. Coil:BDA2X006LSBDA2X009LSBDA2X012LSBDA05024LS
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:Code R990300/B
5. Complete diaphragm:Code 452186/B
MATERIALS:MATERIALS:Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Shutter Standard B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617NOn request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
SPARE PARTS:SPARE PARTS:
FEATURES:FEATURES:
DIMENSIONS:DIMENSIONS:
KIT:KIT:KT130KB30-A=2+3
MAINTENANCE KIT:MAINTENANCE KIT:KTGWA3K0B13=2+4+5
Type PipeISO 228/1
Amm
Bmm
Cmm
21WA3K0B130 G 3/840 97
6021WA4K0B130 G 1/2 66
AB
+-
+-
Open
CloseAB
21WA3K0B130-M÷
21WA4K0B130-M
G 3/8 21WA3K0B130-M12 ~ 2 13
608 0,2 16 16
G 1/2 21WA4K0B130-M 70
AutomationHeating
G 3/8 - G 1/2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
USE::USE::
COILS:COILS:
PIPES:PIPES:
Solenoid valve 2/2 way N.C.With pilot control - Manual operation
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
28-02-2014 ODE 21WA3K0B130-M ÷ 21WA4K0B130-M
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
Max. allowable pressure (PS) 25 barAmbient temperature:See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3K0V130-M
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3K0B130-M G 3/840 97
6021WA4K0B130-M G 1/2 66 B 8 14,5 25 30 42 54
21WA3K0B130-M ÷ 21WA4K0B130-M ODE 28-02-2014
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube: Code R450603
4. Gasket O-Ring:Code R990000/B
5. Manual operational:Code R451772/B
6. Gasket O-Ring:Code R990300/B
7. Complete diaphragm:Code R452186/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130KB30-F=2+3+4KIT:KIT:
KTGWA3K0B13=2+6+7MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
NoteAvailable on request and with minimum quantities.
USE:USE:
PIPES:PIPES:
COILS:COILS:
21WA3K0B130-MM ÷
21WA4K0B130-MM
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,3 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
Solenoid valve 2/2 way N.C.With pilot control
12-06-2014 (Internal technical data sheet) ODE 21WA3K0B130-MM ÷ 21WA4K0B130-MM
PRESENTATION:PRESENTATION:
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 20 barAmbient temperature: See coils catalogue page for its compatibility.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
G 3/8 21WA3K0B130-MM12 ~ 2 13
608 0,3 16 16
G 1/2 21WA4K0B130-MM 70
AutomationHeating
G 3/8 - G 1/2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3K0V130-MM.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:Code R990300/B
5. Complete diaphragm:Code R452726/B
MAINTENANCE KIT:MAINTENANCE KIT:KTGWA3K0B13-MM= 2+4+5
KIT:KIT:KT130KB30-A= 2+3
21WA3K0B130-MM ÷ 21WA4K0B130-MM (Internal technical data sheet) ODE 12-06-2014
DIMENSIONS:DIMENSIONS:
SPARE PARTS:SPARE PARTS:
MATERIALS:MATERIALS:Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
Type PipeISO 228/1
Amm
Bmm
Cmm
21WA3K0B130-MM G 3/840 97
6021WA4K0B130-MM G 1/2 66
FEATURES:FEATURES:
COILTYPE
POWER ABSORPTION DIMENSIONS
W HoldVA ~
InrushVA ~
Dmm
Emm
Fmm
B 8 14,5 25 30 42 54
21WA3K0B130-PC÷
21WA4K0B130-PC
G 3/8 21WA3K0B130-PC12 ~ 2 13 35 8 0,2 16 16
G 1/2 21WA4K0B130-PC
AutomationHeating
G 3/8 - G 1/2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
USE:USE:
COILS:COILS:
PIPES:PIPES:
Solenoid valve 2/2 way N.C.With pilot control - Progressive closing
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
28-02-2014 ODE 21WA3K0B130-PC ÷ 21WA4K0B130-PC
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 25 barAmbient temperature: See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3K0V130-PC.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3K0B130-PC G 3/840 97
6021WA4K0B130-PC G 1/2 66 B 8 14,5 25 30 42 54
21WA3K0B130-PC ÷ 21WA4K0B130-PC ODE 28-02-2014
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:Code R990300/B
5. Complete diaphragm:Code R452401/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130KB30-A=2+3KIT:KIT:
KTGWA3K0B13-PC=2+4+5MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
21WA3R0B130 ÷
21WA4R0B130
G 3/8 21WA3R0B13012 ~ 2 13
605 0,2 12 12
G 1/2 21WA4R0B130 70
Solenoid valve 2/2 way N.C.With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
28-02-2014 ODE 21WA3R0B130 ÷ 21WA4R0B130
PIPES:PIPES:
AutomationHeating
G 3/8 - G 1/2
5W - Ø 10 LBA 155°C (class F)LBF - LBV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
Max. allowable pressure (PS) 25 barAmbient temperature:See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3R0V130
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3R0B130 G 3/840 84,5
6021WA4R0B130 G 1/2 66 L 5 10 15 22 27,5 39,5
21WA3R0B130 ÷ 21WA4R0B130 ODE 28-02-2014
1. Coil:See coils list
2. Complete plunger:Code R451101/B
3. Complete armature tube:Code R452062
4. Gasket O-Ring:Code R990597/B
5. Gasket O-Ring:Code R990300/B
6. Complete diaphragm:Code R452186/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKM E=EPDMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT100R0B25-FJ= 2+3+4KIT:KIT:
KTGWA3R0B13= 2+5+6MAINTENANCE KITMAINTENANCE KIT
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
21WA3R0B130-M÷
21WA4R0B130-M
G 3/8 21WA3R0B130-M12 ~ 2 13
605 0,2 12 12
G 1/2 21WA4R0B130-M 70
Solenoid valve 2/2 way N.C.With pilot control - Manual operation
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
28-02-2014 ODE 21WA3R0B130-M ÷ 21WA4R0B130-M
PIPES:PIPES:
AutomationHeating
G 3/8 - G 1/2
5W - Ø 10 LBA 155°C (class F)LBF - LBV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 25 barAmbient temperature:See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WA3R0V130-M.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3R0B130-M G 3/840 84,5
6021WA4R0B130-M G 1/2 66 L 5 10 15
21WA3R0B130-M ÷ 21WA4R0B130-M ODE 28-02-2014
1. Coil:See coils list
2. Complete plunger:Code R451101/B
3. Complete armature tube: Code R452062
4. Gasket O-Ring:Code R990597/B
5. Manual operation:Code R450576
6. Gasket O-Ring:Code R990300/B
7. Complete diaphragm:Code R452186/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKM E=EPDMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT100R0B25-FJ= 2+3+4KIT:KIT:
KTGWA3R0B13= 2+5+6MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTIONW Hold
VA ~InrushVA ~
21WA3Z0B130÷
21WA4Z0B130
G 3/8 21WA3Z0B13012 ~ 2 13
608 0,2 16 16
G 1/2 21WA4Z0B130 70
Solenoid valve 2/2 way N.O. With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials. .A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPE:PIPE:
AutomationHeating
G 3/8 - G 1/2
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
28-02-2014 ODE 21WA3Z0B130 ÷ 21WA4Z0B130
Max. allowable pressure (PS) 25 barAmbient temperature:See coils catalogue page for its compatibility.
For seals other than NBR replace the letter “B” with the onescorresponding to theother seals. E.I. 21WA3Z0V130.
PipeISO 228/1 Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
PRESENTATION:PRESENTATION:
21WA3Z0B130 G 3/840 97
6021WA4Z0B130 G 1/2 66 B 8 14,5 25 30 42 54
21WA3Z0B130 ÷ 21WA4Z0B130 ODE 28-02-2014
1. Coil:See coils list
2. Complete diaphragmsupport:Code R450788/B
3. Complete armature tubewithout gasket: Code R450573
4. Gasket O-Ring:Code R990000/B
5. Gasket O-Ring:Code R990300/B
6. Complete diaphragm:Code R452186/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617NArmature Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKM E=EPDMOrificie Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 o Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130ZB30-F=2+3+4KIT:KIT:
KTGWA3Z0B13=2+5+6MAINTENANCE KIT:MAINTENANCE KIT:
Type PipeISO 228/1
Amm
Bmm
Cmm COIL
TYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
21WN3K0B130 ÷
21WN9KB500
3/8 NPT 21WN3K0B130
12 ~ 2
1360
8 0,2
16 161/2 NPT 21WN4K0B130 703/4 NPT 21WN5KB190 19 1401 NPT 21WN6KB250 25 190
1 1/4 NPT 21WN7KB350 35 40010 101 1/2 NPT 21WN8KB400 40 520
2 NPT 21WN9KB500 50 750
Solenoid valve 2/2 way N.C.With pilot control
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
USE:USE:
COILS:COILS:
PIPES:PIPES:
AutomationHeating
3/8 NPT - 2 NPT
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 3/8 NPT - 1/2 NPT 25 bar 3/4 NPT - 1 NPT 23 bar 1 1/4 NPT - 2 NPT 16 barAmbient temperature:See coils catalogue page for its compatibility.
CE Approval (Pressure Equipment Directive 97/23/CE)
for S.V. 21WN7÷21WN9
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
For seals other than NBR replace the letter “B” with the onescorresponding to theother seals. E.I. 21WN5KV190.
PipeANSI/ASMEBI.20.1
CodeMax viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E), gasoline gas oil
03-12-2014 ODE 21WN3K0B190 ÷ 21WN9KB500
PRESENTATION:PRESENTATION:
21WN3K0B130 3/8 NPT40 97
6021WN4K0B130 1/2 NPT 6621WN5KB190 3/4 NPT
65105
10421WN6KB250 1 NPT 11221WN7KB350 1 1/4 NPT
98 125 14421WN8KB400 1 1/2 NPT21WN9KB500 2 NPT 118 141 172
B 8 14,5 25 30 42 54
21WN3K0B190 ÷ 21WN9KB500 ODE 03-12-2014
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:3/8 -1/2 NPT Code R990300/B3/4 -1 NPT Code R990002/B1 1/4 -1 1/2 NPT Code R990005/B2 NPT Code R990081/B
5. Complete diaphragm:3/8 -1/2 NPT Code R452186/B3/4 - 1 NPT Code R450431/B
1 1/4-1 1/2 NPT Code R450466/B2 NPT Code R450432/B
MATERIALS:MATERIALS:
SPARE PARTS:SPARE PARTS:
DIMENSIONS:DIMENSIONS:
Body Brass - UNI EN 12165 CW617N Armature tube Stainless steel AISI series 300 Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: E=EPDM V=FKM Orifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
FEATURES:FEATURES:
KT130KB30-A=2+3KIT:KIT:
3/8 - 1/2 NPTKTGWA3K0B13=2+4+53/4 - 1 NPTKTG0W3KB19=2+4+51 1/4 - 1 1/2 NPTKTG0W5KB35=2+4+52 NPTKTG0W7KB50=2+4+5
MAINTENANCE KIT:MAINTENANCE KIT:
Type Pipe Amm
Bmm
Cmm
COILTYPE
POWER ABSORPTION DIMENSIONSW Hold
VA ~InrushVA ~
Dmm
Emm
Fmm
NoteAvailable on request and with minimum quantities.
USE:USE:
PIPES:PIPES:
COILS:COILS:
21WN3K0B130-MM ÷
21WN4K0B130-MM
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,3 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
AutomationHeating
3/8 NPT - 1/2 NPT
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
Solenoid valve 2/2 way N.C.With pilot control
12-06-2014 (Internal technical data sheet) ODE 21WN3K0B130-MM ÷ 21WN4K0B130-MM
PRESENTATION:PRESENTATION:
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WN3K0V130-MM.
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 20 barAmbient temperature: See coils catalogue page for its compatibility.
PipeANSI/ASMEBI.20.1
CodeMax viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
3/8 NPT 21WN3K0B130-MM12 ~ 2 13
608 0,3 16 16
1/2 NPT 21WN4K0B130-MM 70
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
1. Coil:See coils list
2. Complete plunger:Code R450886/B
3. Complete armature tube:Code R450606
4. Gasket O-Ring:Code R990300/B
5. Complete diaphragm with spring:Code R452726/B
MAINTENANCE KIT:MAINTENANCE KIT:KTGWA3K0B13-MM=2+4+5
KIT:KIT:KT130KB30-A=2+3
21WN3K0B130-MM ÷ 21WN4K0B130 -MM (Internal technical data sheet) ODE 12-06-2014
DIMENSIONS:DIMENSIONS:
SPARE PARTS:SPARE PARTS:
FEATURES:FEATURES:
MATERIALS:MATERIALS:Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
Type Pipe Amm
Bmm
Cmm
21WN3K0B130-MM 3/8 NPT40 97
6021WN4K0B130-MM 1/2 NPT 66
COILTYPE
POWER ABSORPTION DIMENSIONS
W HoldVA ~
InrushVA ~
Dmm
Emm
Fmm
B 8 14,5 25 30 42 54
NoteAvailable on request and with minimum quantities.
USE:USE:
PIPES:PIPES:
COILS:COILS:
21WN3R0B130 ÷
21WN4R0B130
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
AutomationHeating
3/8 NPT - 1/2 NPT
5W - Ø 10LBA 155°C (class F)LBF - LBV 180°C (class H)
Solenoid valve 2/2 way N.C.With pilot control
12-06-2014 (Internal technical data sheet) ODE 21WN3R0B130 ÷ 21WN4R0B130
PRESENTATION:PRESENTATION:
For seals other than NBR replace the letter “B” with the ones corresponding to the other seals. E.I. 21WN3R0V130.
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.Max. allowable pressure (PS) 20 barAmbient temperature: See coils catalogue page for its compatibility.
PipeANSI/ASME
BI.20.1Code
Max viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
3/8 NPT 21WN3R0B13012 ~ 2 13
608 0,2 12 12
1/2 NPT 21WN4R0B130 70
Gaskets Temperature Medium
B=NBR (nitrile rubber) - 10°C + 90°C Air, inert gas, water
E=EPDM (ethylene-propylene) - 10°C +140°C Water, low pressure steam
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
1. Coil:See coils list
2. Complete plunger:Code R451101/B
3. Complete armature tube:Code R452062
4. Gasket O-Ring:Code R990300/B
5. Gasket O-Ring:Code R990597/B
6. Complete diaphragm:Code R452186/B
MAINTENANCE KIT:MAINTENANCE KIT:KTGWA3R0B13= 2+5+6
KIT:KIT:KT100R0B25-FJ= 2+3+4
21WN3R0B130 ÷ 21WN4R0B130 (Internal technical data sheet) ODE 12-06-2014
DIMENSIONS:DIMENSIONS:
SPARE PARTS:SPARE PARTS:
FEATURES:FEATURES:
MATERIALS:MATERIALS:Body Brass - UNI EN 12165 CW617NArmature tube Stainless steel AISI series 300Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: B=NBR
On request: E=EPDM V=FKMOrifice Brass - UNI EN 12165 CW617N
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
Type Pipe Amm
Bmm
Cmm
21WN3R0B130 3/8 NPT40 84,5
6021WN4R0B130 1/2 NPT 66
COILTYPE
POWER ABSORPTION
W HoldVA ~
InrushVA ~
L 5 10 15
PRESENTAZIONE:PRESENTAZIONE:
IMPIEGO:IMPIEGO:
RACCORDI:RACCORDI:
BOBINE:BOBINE:
24-02-2014 (Scheda tecnica interna) ODE 21WN3Z0V130 ÷ 21WN4Z0V130
La “ODE” si riserva il diritto di apportare modifiche tecniche ed estetiche senza obbligo di preavviso.
NotaSu richiesta e per quantità.
21WN3Z0V130 ÷
21WN4Z0V130
E.V. ad azione indiretta adatta all’intercettazione dei fluidi compatibli con i materiali costruttivi.È richiesta una pressione minima di funzionamento di 0,2 bar.I materiali utilizzati e le prove eseguite garantiscono affidabilità e durata.
AutomazioneRiscaldamento
3/8 NPT - 1/2 NPT
8W - Ø 13 BDA - BSA 155°C (classe F)BDV 180°C (classe H)
Elettrovalvola 2/2 vie N.A. Azione indiretta
INCAPSULAMENTO E ROCCHETTO SONO REALIZZATICON MATERIALE VERGINE AL 100%.Pressione massima ammissibile (PS) 20 bar Temperatura ambiente:Consultare le pagine di catalogo bobine per le relative compatibilità.
RaccordoANSI/ASMEBI.20.1
CodiceViscosita maxammissibile
Ø
mm
Kv PotenzaPressione
min M.O.P.D.cSt °E l/min watt bar AC bar DC bar
3/8 NPT 21WN3Z0V13012 ~ 2 13
608 0,2 16 16
1/2 NPT 21WN4Z0V130 70
Per tenute diverse dal FKM sostituire la lettera “V” con le lettere corrispondenti alle altre tenute. Es. 21WN3Z0B130.
Guarnizioni Temperatura Fluidi
B=NBR (nitrile) - 10°C + 90°C Acqua, aria, gas inerti
E=EPDM (etilene-propilene) - 10°C +140°C Acqua, vapore bassa pressione
V=FKM(elastomero fluorurato) - 10°C +140°C Olii leggeri (2°E),benzina
gasolio
21WN3Z0V130 ÷ 21WN4Z0V130 (Scheda tecnica interna) ODE 24-02-2014
DIMENSIONI:DIMENSIONI:
MATERIALI:MATERIALI:
CARATTERISTICHE:CARATTERISTICHE:
PARTI DI RICAMBIO:PARTI DI RICAMBIO:1. Bobina:Vedi elenco bobine
2. Assieme portaguarnizione:Cod. R450788/V
3. Assieme cannotto senzaguarnizione:Cod. R450573
4. Guarnizione O-Ring:Cod. R990000/V
5. Guarnizione O-Ring:Cod. R990300/V
6. Assieme membrana:Cod. R452186/V
Corpo Ottone - UNI EN 12165 CW617NCannotto Acciaio inox AISI serie 300Nucleo fisso Acciaio inox AISI serie 400Nucleo mobile Acciaio inox AISI serie 400Anello di sfasamento Rame - Cu 99,9%Molla Acciaio inox AISI serie 300Otturatore Standard: V=FKM
A richiesta: E=EPDM B=NBROrificio Ottone - UNI EN 12165 CW617N
A richiesta:Connettore Pg 9 o Pg 11Conformità connettore ISO 4400
Conformità elettriche IEC 335Grado di protezione IP 65 EN 60529 (DIN 40050)
con elettromagnete corredato di connettore.
KIT:KIT:KT130ZB30-F= 2+3+4
KIT MANUTENZIONE:KIT MANUTENZIONE:KTGWA3Z0B13= 2+5+6
Tipo Raccordo Amm
Bmm
Cmm
21WN3Z0V130 3/8 NPT40 97
6021WN4Z0V130 1/2 NPT 66
BOBINATIPO
POTENZA DIMENSIONI
W EsercizioVA ~
Allo spuntoVA ~
Dmm
Emm
Fmm
B 8 14,5 25 30 42 54
PRESENTATION:PRESENTATION:
08-05-2014 (Internal technical data sheet) ODE 21WN6K1V250-10T5
The “ODE ” reserves the right to carry out technical and aesthetic modifications without prior notification.
Note : Available on request and with minimum quantities.
21WN6K1V250-10T5Solenoid valve 2/2 way N.C.With pilot control - NSF Certified
S.V. with pilot control for interception of fluids compatible withthe construction materials.A minimum operational pressure of 0,2 bar is required.The materials used and the tests carried out ensure maximumreliability and duration.
Max. allowable pressure (PS) 25 bar Ambient temperature:See coils catalogue page for its compatibility.
USE:USE:
PIPES:PIPES:
COIL:COIL:
AutomationHeating
1 NPT
8W - Ø 13BDA - BSA 155°C (class F)BDV 180°C (class H)
COIL HOUSING AND COIL FORMER MATERIAL AREMADE BY 100% VIRGIN MATERIAL.
PipeANSI/ASMEBI.20.1
CodeMax viscosity Ø
mm
Kv PowerPressure
min M.O.P.D.cSt °E l/mn watt bar AC bar DC bar
1 NPT 21WN6K1V250-10T5 12 ~ 2 25 190 8 0,2 16 16
Gaskets Temperatur Medium
V=FKM (fluoroelastomer) - 10°C +140°C Mineral oils (2°E),gasoline gas oil
E=EPDM(ethylene-propylene) - 10°C +140°C Water
For seals other than FKM replace the letter “V” with the ones corresponding to the other seals. E.I. 21WN6K1E250-10T5.
21WN6K1V250-10T5 (Internal technical data sheet) ODE 08-05-2014
DIMENSIONS:DIMENSIONS:
MATERIALS:MATERIALS:
FEATURES:FEATURES:
SPARE PARTS:SPARE PARTS:
Body Low Lead Brass Armature tube Stainless steel AISI series 300 Fixed core Stainless steel AISI series 400Plunger Stainless steel AISI series 400Phase displacement ring Copper - Cu 99,9%Spring Stainless steel AISI series 300Seal Standard: V=FKM
On request: E=EPDMOrifice Low Lead Brass
On request:Connector Pg 9 or Pg 11Connector conformity ISO 4400
Electrical conformity IEC 335Protection degree IP 65 EN 60529 (DIN 40050)
with coil fitted by connector.
COILTYPE
POWER ABSORPTION DIMENSIONS
W HoldVA ~
InrushVA ~
Dmm
Emm
Fmm
B 8 14,5 25 30 42 54
Type Pipe Amm
Bmm
Cmm
21WN6K1V250-10T5 1 NPT 65 113 104
1. Coil:See coils list
2. Complete plunger:Code R450886/VX1
3. Assieme cannotto:Code R450811
4. Gasket O-Ring:Code R990000/VX1
5. Manual operation:Code R451772/VX1/P
6. Gasket O-Ring:Code R990002/VX1
7. Complete diaphragm:Code R453117/VX1/P
8. Regulation screw:Code R450728/VX1/P