LAMA has developed over the years a wide range of products that can be used in the waterproofing and damp-proofing of roofs, decks, car parkings, walls, foundations, basements, roads,…etc.
In this catalogue, there are five main Product categories
WATERPROOFING MEMBRANES
WATERPROOFING & PROTECTIVE COATINGS
SEALANTS
BITUMINOUS FELTS
BONDING ASPHALT
OTHER PRODUCTS
REINFORCED FIBERGLASSAPP Modifi ed Bitumen Membrane
DescriptionMost economical waterproofing 3 or 4mm thick membrane,Excellent resistance to heat aging and weathering, Dimensional stability to membrane sheet due to the reinforcement of a rot-proof fiberglass mat 60g/m2.
Technical specificationsDimensions 1×10 m RollThickness 3 or 4mmCold Pliability no cracking at -5ºCSoftening Point 150ºC±10Penetration 20±10 dmm
OGV
WATERPROOFING MEMBRANES
WATERPROOFING MEMBRANES
Spunbond PolyesterAPP Modifi ed Membrane
DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 150g/m2,High performing membrane,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specificationsDimensions 1×10 m RollThickness 3 or 4mmCold Pliability no cracking at -5ºCSoftening Point 150ºC ±10Penetration 20±10 dmm
PETRAGUM
WATERPROOFING MEMBRANES
APP Modifi ed Bitumen Membrane
DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 180g/m2,High performing membrane,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -8ºCSoftening Point 150ºC ±10Penetration 20±10 dmm
AMAN
WATERPROOFING MEMBRANES
SPUNBOND POLYESTERAPP Modifi ed Bitumen Membranes
DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2,Most suitable for use in TROPICAL areas,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -12ºCSoftening Point 150ºC ±10Penetration 20±10 dmm
TPY
WATERPROOFING MEMBRANES
SPUNBOND POLYESTERAPP Modifi ed Bitumen Membranes
DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2,High performing membrane,Excellent weathering and ageing resistance.High flexibility at low temperatures.High puncture, tear, and Hydrostatic pressure resistance.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -15ºCSoftening Point 150ºC ±10Penetration 20±10 dmm
MPY
WATERPROOFING MEMBRANES
Spunbond Polyester APP Modifi ed Membrane
DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester of different weights to give the needed elongation,High performing membrane,Resistance to heat aging, puncture, and rottingExcellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at (-5) – (-10) ºC depending on the reinforcementSoftening Point 150ºC ±10Penetration 20±10 dmm
ECOGUARD
WATERPROOFING MEMBRANES
SPUNBOND POLYESTERSBS Modifi ed Bitumen Membranes
DescriptionModified with Styrene Butadiene Styrene (SBS) and reinforced with Non-woven Spunbonded Polyester ranging from 180g/m2 to 200g/m2,Excellent elasticity,High aging, puncture, and tear ResistanceGood resistance to acids, sulphates and chlorides.High flexibility at low temperatures.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at (-15) – (-20) ºC Softening Point 130ºC ±10Penetration 25±10 dmm
SPY
WATERPROOFING MEMBRANES
DOUBLE REINFORCEMENTAPP Modifi ed Bitumen Membrane
DescriptionMade with a double reinforcement of 180 g/m² non-woven polyester and 60 g/m² fiberglass,High dimensional stability,High thermal aging, and puncture ResistanceWithstanding extreme temperatures.
Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -5 ºC Softening Point 150 ºC ±10Penetration 20±10 dmm
GLASTER
WATERPROOFING MEMBRANES
DOUBLE-REINFORCEMENTAPP Modifi ed Bitumen Membranes
DescriptionMade with a double reinforcement of 200 g/m² non-woven polyester and 60 g/m² fiberglass,Used in heavy duty applicationsHigh dimensional stability,High thermal aging, and puncture ResistanceHydrostatic pressure and Load strain resistance.
Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10Penetration 20 dmm
TPG
WATERPROOFING MEMBRANES
Bridge Deck Waterproofi ng Membranes
DescriptionMade with a double reinforcement of 250 g/m² non-woven polyester and 60 g/m² fiberglass,Designed for use in road works,High dimensional stability,Puncture & tear, Impact, and Fuel Resistance.
Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -5 ºC Softening Point 155 ºC ±10Penetration 20±10 dmm
TPG HEAVY
WATERPROOFING MEMBRANES
Anti-Root Waterproofi ng Membrane
DescriptionMade with 180 or 200 g/m2 nonwoven polyester fabric reinforced with fiberglass filaments,Bitumen is specially treated with an antiroot formulation, with the addition of Preventol B2 Used in areas where plantation can damage the waterproofing layers (Plant root resistance)High dimensional stability,Excellent elasticityHigh Puncture & tear Resistance, Resistance to aging, acids, sulfates and chlorides.
Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5 mmCold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10Penetration 20±10 dmm
LAMA GARDEN
WATERPROOFING MEMBRANES
Bituminous Protection Board
DescriptionSemi rigid protection board, covered on both sides with a polyethylene filmProtect the waterproofing membrane from construction abuse and harmful puncture.It gives protection against normal foot traffic as well as the wearing caused by built-up over layers for horizontal surfaces Protection against rotting and decomposingTough and durable protective cover for protecting various waterproofing systems.
Technical specificationsDimensions 1×2 m Board or 1×10 RollThickness 3, 4, 5 and 6 mmSoftening Point 130 ±10
LAMA BOARD
WATERPROOFING & PROTECTIVE COATINGS
Highly Penetrative Bituminous Primer
PropertiesSolvent base cold applied, highly penetrative thin bituminous solution, black in color.Used for priming concrete, masonry, metal, asphalt surfaces, and as a priming coat before applying any LAMA bituminous coating, or modified bitumen membrane.Complies with the requirements of ASTM D 41 Type I.Covers from 2-3 m²/liter dependent upon porosity of surface.Supplied in 20 and 200 liter drums.
Technical specificationsFlash point 40 ºCPenetration @ 25 ºC 20-50 dmmViscosity @25 ºC 25-125 s
LAMA PRIMER
WATERPROOFING & PROTECTIVE COATINGS
Asphalt Roof Coating (Regular and Fast Drying)
A solvent-born bituminous compound of brushable consistency, dries to a tough, black coating, which does not flow under summer heat. A general purpose waterproofing and damp-proofing coating.Used as a primer where concrete surfaces are porousProvides protection against corrosion.Recommended where the threat of frost or rain precludes the use of an emulsionComplies with the requirements of ASTM D4479 Type II and BS 3416.Covers approximately 1.6 m²/liter.Supplied in 20 and 200 liter drums.
Technical specificationsFlash point 60 ºCSpecific gravity 0.90
SEALCOAT
WATERPROOFING & PROTECTIVE COATINGS
Rubberized Bitumen Emulsion, Waterproofer and Adhesive
A dark brown cold applied rubberized bitumen emulsion, dries to form a black flexible coating.Used as a water and moisture barrier, an adhesive, a plaster bonding agent and a primer.Provides protection against metal corrosionProvides weatherproofing layer when used over exposed insulationComplies with the requirements of ASTM D 1227, Type III, Class 1Covers approximately 1.3 m²/liter.As a Primer it covers approximately 5 m²/liter.Supplied in 20 and 200 liter drums.
Technical specifications:Specific gravity 980-1040Residue by evaporation 47-53 %
LAMASOL
WATERPROOFING & PROTECTIVE COATINGS
Protective Fibrated Coating A dark brown cold applied asphalt emulsion prepared emulsifying agents and containing non-asbestos fibers, for reinforcement.Used as a water and moisture barrier, also as a vapor barrier.Provides protection against metal corrosionProvides weatherproofing layer when used over exposed insulationComplies with the requirements of ASTM D 1227 type II, class 1.Covers approximately 2 m²/liter.Supplied 20 liter drums.
Technical specificationsSpecific gravity 980 – 1080Residue by evaporation 45 – 55 %
FIBERSOL
WATERPROOFING & PROTECTIVE COATINGS
Below Ground Asphalt Coating
Cutback petroleum asphalt of rapid curing type, and of brushable consistency. Dries to tough, highly adhesive, black coatings.Resists the attack of salt solutions, sulphates, and dilute acids.A general purpose waterproofing coating.Complies with the requirements of ASTM D4479 Type 1.Covers approximately 1.0 m²/liter.Supplied in 20 and 200 liter drums.
Technical specificationsViscosity 100-220 sec.Penetration @ 25 ºC 80-120 dmm.Flash Point 27 ºC
RC-25 IMPROVED
WATERPROOFING & PROTECTIVE COATINGS
Bituminous High Elastic Rubberized Coating
Cold applied bituminous rubberized solvent based compound, black in color.Excellent and full adhesion to concrete surfaces.High elasticity.Self-repairing in case of a little puncture.Moisture resistant.Covers approximately 1.0 m²/liter.Supplied in 20 liter drums.
Technical specificationsFlash point 40 ºCElongation 1000/100
RUBBERCOAT
WATERPROOFING & PROTECTIVE COATINGS
Crack Bridging and Protective Coating System For Concrete and Masonry
Waterproofing elastomeric and durable white emulsion.Provides a protective and reflective layer to the coated surface.For heat and sound insulation, waterproof and anti-rust protection.High solar reflectivity and U.V. resistance.Frost, de-icing salts and CO2 resistance.Complies with the requirements of AWWA C-203.Covers approximately 1.0 m²/liter.Supplied in 20 liter drums.
Technical specifications:Elongation at 25 °C Over 300%Service temperature -5 to 80 ˚C.Solids contents 62%
LAMACRYL
WATERPROOFING & PROTECTIVE COATINGS
Bituminous Aluminum Coating
A light/heat reflective and decorative coating.Asphalt base, aluminum-pigmented non-fibered protective coating dries to a bright silvery finish.for use over bituminous coatings, modified bitumen roofs, metal roofs, primed steel and masonry walls.Complies with the requirements of ASTM D 2824, type I.Covers approximately 0.8-1 m²/liter.Supplied in 20 liter drums.
Technical specificationsFlash point 38 °CReflectance 70%
LAMASILVER
WATERPROOFING & PROTECTIVE COATINGS
Stone Water Repellent
A transparent liquid.Closes the pores and forms a water repellent layer inside the element and at the surface while permitting the trapped vapor to move out.For coating stone, concrete, asbest-cement, and brickResistant to salt solutions, dilute acids, alkalis and U.V.Covers approximately 4 m²/liter depending on the concrete or stone porosity..Supplied in 20 liter drums.
Technical specificationsSpecific gravity about 0.8
LAMASTONE
WATERPROOFING & PROTECTIVE COATINGS
Highly Elastic Rubberized Liquid Membrane
PropertiesA liquid cold applied bituminous membrane, black in color.used to resist the plant root penetration and designed for use in planted roofsRubberized solvent based compound of a very high elasticity and Highly adhesiveGood resistance to acids, sulfates and chlorides.High flexibility at low temperaturesBonds to asphalt and bitumen surfaces, ideal for repair of failed and aged coatingsResistance to agingSupplied in 20 liter drums.
Technical specificationsFlash point 40 ºCSoftening Point 95 ºC
Garden Rubber
BONDING ASPHALT
BLOWN ASPHALT85/25 & 115/15 for Built-up Roofi ng
PropertiesProduced by air blowing of petroleum residues.The grade depends on the softening point and the penetration degree.Used in the construction of built up roofing as bonding or flood coats.Complies with the requirements of B.S 3690: part 2, ASTM D312: Type III & Type IV, and Jordanian National Building code (Vol. ll-Ch5) Tables No. 15 & 17.Supplied in 180 kg drums (85 / 25) and 20 kg plastic wraps (115 / 15).
Technical specificationsPenetration @ 25 ºC 25±5 (85 / 25), 15±5 (115 / 15). Softening Point 80-90 ºC (85 / 25), 110-120 ºC (115 / 15).
BONDING ASPHALT
For MASTIC ASPHALT on Roofs
PropertiesProduced by air blowing of petroleum residues.It is mixed in-place with other components like limestone aggregate, cement and hydrated lime to give a waterproofing material, solid or semi-solid under normal weather conditions.Softens gradually when heated to 200°C, so it can be spread easily on the roofs.Used in the construction of built-up roofing as waterproofing and adhesive layerType I & IV complies with ASTM D 312.Supplied in 180 kg steel drums.
Technical specificationsPenetration @ 25 ºC 18-60 (Type I), 12-25 (Type IV)Softening Point 57-66 (Type I), 99-107 (Type IV).
OXIDIZED ASPHALT
MASTICS AND SEALANTS
Hot Poured Elastic Concrete Joint Sealer
PropertiesHot poured sealant composed of special asphalt, plasticizers, rubber and fillers.Used for sealing joints.Excellent Adhesion, Good Elasticity, and Water Resistance.Use 1200g for 1000cc.Complies with the requirements of B.S 2499, Type N1, ASTM D1190, ASTM D3405, ASSHTO M-173, and ASSHTO T-187Supplied in 5 gallon drum and 20 kg block..
Technical specificationsFlash point 250 ºC min.Softening Point 100 ºC min.Penetration @ 25 ºC 90 dmm max
FLEXI-JOINT
MASTICS AND SEALANTS
Concrete Joint Sealer, Hot-Poured Elastic Type
PropertiesA black resilient and adhesive compound.effectively sealing joints in concrete against penetration of moisture and foreign material Excellent adhesion to bitumen and concrete surfaces.Good elasticity, High water resistance, and Weather resistant Use 1300g for 1000cc.Complies with the requirements of B.S. 2499 (Type N2).Supplied in 20 liter steel drums.
Technical specificationsSpecific gravity 1.20Penetration @ 25 ºC 90 dmm max.
ROFLEX
MASTICS AND SEALANTS
Cold Applied, Sealant
PropertiesA blend of special asphalts, plasticizer and fillers. Soft for easy use, highly elastic and weather proof.Good adhesion without primer.Used for easy and fast sealing.Complies with the requirements of ASTM C920, Grade NS.Supplied in 20 liter drums.
Technical specificationsSpecific gravity 1.20Softening Point 80 ºC min.Penetration @ 25 ºC 85 dmm max
LAMA SEAL
MASTICS AND SEALANTS
Trowel-Applied Asphalt Roof Cement
PropertiesA black bituminous paste consists of an asphalt base, solvents, mineral stabilizers and fibers. Suitable for application by trowel or spatula.For sealing joints and cracks in bituminous membranes, concrete and other surfaces.Protect metallic surfaces and dampen their noise.Covers 0.3 m²/liter (giving 3 mm wet thickness)Complies with the requirements of ASTM D4586, Type II.Supplied in 20 liter drums.
Technical specificationsFlash point Approx. 50°C Specific gravity Approx.1.05
LAMA MASTIC
WATERPROOFING & DAMPPOOFING FELTS
LAMAFELT-18Organic Fiber Base for Damp Proof Course Consists of a sheet of matted organic fibers impregnated with asphalt and coated on both faces with blown bitumen and covered with fine granules. used in built-up roofing and as a vapor barrier under roof insulationComplies with the requirements of BS 747 type 1B.
LAMAFELT-36Glass Fiber Base for Damp Proof Course
Consists of reinforced fiber glass base coated on both sides with bitumen and covered with fine granules. Suitable for use as the lower layer(s) of built-up roofing and as the top layer on flat roofs and vapor barrier under roof insulation. Complies with the requirements of BS 747 - type 3B.
WATERPROOFING & DAMPPOOFING FELTS
LAMA PERFOFELTGlass Fiber Base
A glass fiber mat with 40 mm diameter perforations saturated with asphalt and coated with bitumen and covered with fine granule surfacing material. Used primarily as a venting base sheet in built-up roofing and may be used as a loosely laid layer over the prepared substrate, beneath the torch applied LAMA waterproofing membrane.
LAMA POLYFELTFor Roofi ng and Waterproofi ng
Non-woven polyester mat saturated with oxidized bitumen and faced on the upper side with fine granule and on the bottom side with polyethylene sheet. Excellent durability, resistant to germs and yeasts, and highly flexibility.Used in built-up roofing in layers bonded in bitumen and as under lays for mopping asphalt.
WATERPROOFING & DAMPPOOFING FELTS
LAMA MESHFiberglass Net 70
A fiberglass net of excellent site serviceability, specially designed for use as a reinforcement of waterproofing coats for the roofs and foundations, to reinforce marble slabs of vertical walls and surface layers, and reinforcing cold and hot asphalt coats. It doesn’t dissolve with the organic solvents in the asphalt and it is a rot and fungi proof.
LAMA PAPERFELTAsphalt-Saturated Organic Felt
Consists of a sheet of organic fiber saturated with asphalt and covered with fine granules. Used in damp proofing of heat insulated water pipes due to its flexibility and as a vapor barrier under roof insulation, or for damp proofing in foundations.
WATERPROOFING & DAMPPOOFING FELTS
LAMA JUTEFor Roofi ng and Waterproofi ng
A woven burlap fabric saturated with asphalt and covered with one layer of polyethylene sheet on each side. used in built-up roofing in 3 or more layers bonded in hot oxidized bitumen and underlay for mastic asphalt in roofing, flooring and retaining walls. Complies with the requirements of ASTM D 1327.
OTHER PRODUCTS
STEELCOATFor protecting iron and steel
A hot applied bitumen based coating with inert non-fibrous fillers. It is solid at the normal temperatures, and softens gradually when heated turning into a very viscous liquid at about 130˚C. At higher temperatures the viscosity drops, turning the mixture into a thin and easy to apply liquid. Used to provide a protective layer over steel pipes and fittings against corrosion. Complies withrequirements of the BS4147: Type A-Grade B.
STEELPRIMEFor protecting iron and steel
A primer for cold application over iron and steel, consisting of a homogeneous solution of bitumen in a fast drying solvent. When dry, it provides an effective bond between the metal and the subsequent coating. Complies with the requirements of BS4147: Type A-Grade B.
ASPHALTOPLASTMineral Rubber
A mineral rubber blown bitumen specifically for use by polymer compound.
Top Related