06/2010 Technical Manual
MESA - KSK
Gable Platform System for
Exterior Operations
Contents
Introduction
System Description 1 Working Limits 2 Scope of Applications 3
System Overview 4
Sets 12
Dimensions 19
Timbers 21
Part List
Basic System 24 Main System Sets 25 Tie-Shoe Sets 30
Anchor-Shoe Sets 31
Extension Sets 32
Platform-to-Platform Connections 33
General Remarks
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Important Note
Sight-Check
Information
Warning
Remarks
Symbols Used
� All products of MESA should be used
according to the relevant safety regulations of
the state or country in which they are operated.
� Schematic illustrations on this manual give
only basic rules to be applied during assembly,
therefore it does not complete from the safety point
of view.
� MESA products could only be used
according to the Instruction or User Manuals,
any Technical Details given in Documents
provided by MESA.
� Any MESA products could not be combined
with the products of other manufacturers.
� Mesa Imalat reserves the right to make
technical changes in the interests of progress.
© Copyright by MESA Imalat San.ve Tic A.S.-
Ankara-Turkey
Warranty
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Warranty Period
� Limited Warranty for two (2) years is
promissed by Mesa İmalat San.ve Tic. A.Ş. for
Steel Face Formworks and Slab Formworks
unless the Operational Conditions described
below are violated.
� This warranty covers defects of steel
material, welding and painting.
� For Hydraulic Cylinders and Hydraulic
Power Units , the limited warranty period is one
(1) year.
Service Life
� Steel Face Formworks and Slab
Formworks, produced by Mesa İMALAT San.ve
Tic.A.Ş., is good for 500 concrete castings
unless The Operational Conditions described
below are violated.
Operational Conditions
� Instruction or User’s Manuals must be
used while Formwork assemblies, accessory
attachements and concrete casting.
� It is not allowed to use hummer,
sedgehummer, cranka and vs that cause physical
demage on Formworks, and also applications of
extra welding, cutting and drilling without permission
of authorities.
� It is not allowed to exceed the Max
Concrete Pressure described in Technical or
User’s Manuals.
� Formwork should be used between + 40 °C
and – 30 °C.
� Formworks should be cleaned after each
application to remove the concrete residues and
active faces should be lubricated with suitable
concrete/metal seperation oil.
� After 250 applications, maintenance should
be done at site.
� This maintenance covers the flatning of
active surface, repainting, welding and rust
control.
� After 500 applications, maintenance should
be done at work shop where the necessary
equipments exist.
� During the storage period, all active
surfaces should be lubricated with suitable oil to
prevent rusting.
� Stock area should be closed area; if it is not
possible, formworks and accessories should be
stocked in open areas by covering them with water
resistant materials.
� Maitenance procedure should be
repeated for each 250 usages after first 500
usages are exceeded.
� For HCP-hydraulic system, the allowable
working pressure must not be exceeded ( 250 bar ).
� All connections between hydraulic
cylinders, hydraulic power units and hydraulic
pipes and must be checked against leakage
before each usage.
� Electrical power supply and connections
must be suitable as written in the ınstruction or
User’s Manuals given by MESA.
Introduction System Description
Gable Endframe System – KSK
1
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
SYSTEM DESCRIPTION
Basic Introduction
MESA-KSK Gable Platform System is designed and
manufactured for exterior working on formwork or any
other construction operations.
It creates a reliable working and walking area for the
crew dealing with all types of formworks or facade
operations.
Basically, system includes two or three foldable
Triangular Brackets, main supporting beam which
hangs on the shoes mounted on the wall and connects
these brackets at the same time, supplementary
connection profiles, post guardrails for safety, steel
girders and timber covers on platform areas.
MESA-KSK Gable Platform is lifted and transferred by
means of cranes.
It provides high degree of reliability and durability in the
range of loading and working limits given in this
manual.
The fundamental advantage of the system is the
versatility on different construction plans.
Scope of Applications
Universal design of MESA-KSK Gable Platform System
gives wide range of application on construction sites.
Before concreting, System assures a powerful bearing
and shoring area for all type of tunnel formworks, wall
formworks and even falseworks
During concreting, a safe, accessible and convenient
working place for concreting crew is achieved by the
System.
Also, for masonry work, brickwork, heavy
cladding,rendering, plastering, and painting, MESA-
KSK Gable Platform System is ready to use.
Standart Lengths
Effective length of MESA-KSK Gable Platform System
having double Triangular Brackets is varying from
1,500 mm to 5,500 mm by adjusting the distance
between two Triangular Brackets and the cantilever in
both sides.
In the Sets having triple Triangular Brackets, effective
length is in between 3,750 mm and 8,750 mm by
adjusting the distance between two Triangular Brackets
and the cantilever in both sides.
Combination of two sets of MESA-KSK Gable Platform
System with double Triangular Brackets gives effective
platform length changing from 6,800 mm to 10,200 mm.
Standart Width
Working area of MESA-KSK Gable Platform System
has 1,800 mm effective width.
By means of Front Extension Set, effective width could
be increased to 2,850 mm.
Introduction Working Limits
Gable Endframe System – KSK
2
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
WORKING LIMITS
Dimensional Limits
Maximum platform length of MESA-KSK Gable
Platform with double Triangular Brackets is 3,750 mm
exluding cantilever parts of the platform.
Maximum platform length of MESA-KSK Gable
Platform with triple Triangular Brackets is 6,750 mm
exluding cantilever parts of the platform.
Maximum cantilever platform length on each
sides is 1,135 mm except otherwise stated.
Maximum platform length of MESA-KSK Gable
Platform with double Triangular Brackets is 5,500 mm
including cantilever parts of the platform.
Maximum platform length of MESA-KSK Gable
Platform with triple Triangular Brackets is 8,750 mm
including cantilever parts of the platform.
Maximum platform length of 2 sets of MESA-
KSK Gable Platform with double Triangular Brackets is
10,200 mm including cantilever parts of the platform.
Maximum width of the effective platform area is
2,850 mm.which is obtained by adding front extension
set. The width of Standart Platform is1,800 mm.
Loading Limits
In minimum span length of double Triangular
Brackets which is 1,000 mm ;
� Maximum Formwork Weight is 2,910 kg.
� Maximum Distributed Load is 490 kg/m².
� Maximum Linear Load is 655 kg/m.
Introduction Scope of Applications
Gable Endframe System – KSK
3
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
SCOPE of APPLICATIONS
KSK-Gable Platform on Tunnel Formwork Applications
Applicability on different combinations
KSK-Gable Platform with access platform on corners
KSK-Gable Platform under Column and Wall Form
KSK-Gable Platform providing necessary safety
KSK-Gable Platform on large application areas
Introduction System Overview
Gable Endframe System – KSK
4
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Side Guardrail Set* are not included in
Std.System Sets.
Open ends must be kept by Side Guardrail
Set* .
Shoe Set* are not included in Std.System
Sets. Types and quantities of Shoe Set*
are derived according to the solution
requirements.
Types B1 and B2 of Shoe Set* are
described in Section “Sets” of this
Manual.
SYSTEM OVERVIEW
Basic KSK-Gable Platform System
with 2-Triangular Bracket
Basic System
Triangular Bracket – A
Shoe Set* – B1/B2
Support Set – C2
Holder Set – D2
Side Guardrail Set* – F
Guardrail Set – E
Timbers
Safety Timber
Girder Timber
Cover Timber
Introduction System Overview
Gable Endframe System – KSK
5
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Descriptions on KSK-Gable Platform
System with 2-Triangular Bracket is valid
for The System with 3-Triangular Bracket.
Basic KSK-Gable Platform System
with 3-Triangular Bracket
Timbers
Girder Timber
Guardrail Timber
Cover Timber
Basic System
Triangular Bracket – A
Shoe Set – B1/B2
Support Set – C3
Holder Set – D3
*Side Guardrail Set – F
Std.Guardrail Set – E
Mid.Guardrail Set – G
Introduction System Overview
Gable Endframe System – KSK
6
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
For Lower Extension,
1 set of Telescopic Diagonal,
1 set of Bracket Connector and
1 set of Lower Vertical is required for each
Triangular Bracket .
Support Set is choosen according to the
Nominal Length of KSK-Platform.
Basic KSK-Gable Platform System +
Lower Extension
Lower Extension System
H - Telescopic Diagonal Set
C2/C3 - Support Set
J - Bracket Connector Set
K - Lower Extension Set
Introduction System Overview
Gable Endframe System – KSK
7
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
For Lower Platform,
1 set of Lower Platform and,
1 set of Lower Vertical is required for each
Triangular Bracket .
Support Set is choosen according to the
Nominal Length of KSK-Platform.
Basic KSK-Gable Platform System +
Lower Platform
Lower Platform System
Lower Extension Set - K
Support Set - C2/C3
Lower Platform Set - L
Introduction System Overview
Gable Endframe System – KSK
8
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
For Front Extension,
1 set of Front Horizontal and,
1 set of Telescopic Diagonal is required
for each Triangular Bracket .
Basic KSK-Gable Platform System +
Front Extension
Front Extension System
Telescopic Diagonal Set - H
Front Extension Set - M
Introduction System Overview
Gable Endframe System – KSK
9
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Basic KSK-Gable Platform System +
Lower Extension +
Front Extension
Basic KSK-Gable Platform System +
Lower Extension +
Lower Platform
Lower & Front Extension System
M - Front Extension Set
H - Telescopic Diagonal Set
C2/C3 - Support Set
J - Bracket Connector Set
K - Lower Extension Set
Lower Extension & PlatformSystem
L - Lower Platform Set
C2/C3 - Support Set
J - Bracket Connector Set
K - Lower Extension set
H - Telescopic Diagonal Set
Introduction System Overview
Gable Endframe System – KSK
10
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Basic KSK-Gable Platform System +
Lower Extension + Lower Platform +
Front Extension
Basic System
Std.Guardrail Set - E
Mid.Guardrail Set - G
Shoe Set - B
Triangular Bracket - A
Support Set - C
Holder Set - D
Extensions
M - Front Extension Set
H - Telescopic Diagonal Set
L - Lower Platform Set
J - Bracket Connector Set
K - Lower Extension Set
Introduction System Overview
Gable Endframe System – KSK
11
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Connection of Two Sets of
KSK-Gable Platform System
N - Holder Spacer P - Holder End Set
R -Support Spacer Set S -Support End Set
Introduction Sets
Gable Endframe System – KSK
12
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
SETS
A - Triangular Bracket (Foldable)
Parts
Bracket Horizontal (1 pcs)
Bracket Diagonal (1 pcs)
Bracket Vertical (1 pcs)
Pin-Ø14x100 (1 pcs)
Spring Pin-2.5 (4 pcs)
Pin-Ø14x115 (3 pcs)
1
2
3
4
Introduction Sets
Gable Endframe System – KSK
13
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
B1 – Tie-Shoe Set
B2 – Anchor-Shoe Set
Parts
Wing Nut (1 pcs)
Plate (1 pcs)
Shoe-Tie (1 pcs)
Spring Pin-3 (1 pcs)
Shoe (1 pcs)
Parts
E - Std.Guardrail Set (1 set)
M16x100 Bolt (2 pcs)
M16 Washer (2 pcs)
M16 Nut (2 pcs)
Side Guardr.Connector (1 pcs)
Parts
Guardrail Post (1 pcs)
M14x80 Bolt (2 pcs)
M14 Washer (2 pcs)
M14 Nut (2 pcs)
Parts
E - Std.Guardrail Set (1 set)
Mid.Guardr.Connector (1 pcs)
G – Mid.Guardrail Set
F – Side Guardrail Set E - Std.Guardrail Set
Parts
Anchor Screw (1 pcs)
M24 Washer (1 pcs)
M24x70 Bolt (1 pcs)
Anchor Shoe (1 pcs)
Introduction Sets
Gable Endframe System – KSK
14
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
C2 - Support Set ( for 2-Triangular
Bracket System )
C3 - Support Set ( for 3-Triangular
Bracket System )
Parts
C2-Support (1 pcs)
Pin-Ø14x100 (2 pcs)
Spring Pin-2.5 (2 pcs)
Parts
C3-Support (1 pcs)
Pin-Ø14x100 (3 pcs)
Spring Pin-2.5 (3 pcs)
N
N
N(mm) Part
1,500 C2-Support (1500)
2,000 C2-Support (2000)
2,500 C2-Support (2500)
3,250 C2-Support (3250)
3,500 C2-Support (3500)
N(mm) Part
2,730 C3-Support (2730)
3,730 C3-Support (3730)
4,730 C3-Support (4730)
6,230 C3-Support (6230)
6,730 C3-Support (6730)
Introduction Sets
Gable Endframe System – KSK
15
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
D2 - Holder Set ( for 2-Triangular
Bracket System )
D3 - Holder Set ( for 3-Triangular
Bracket System )
Parts
D2-Holder (1 pcs)
M14 Nut (4 pcs)
M14 Washer (4 pcs)
M14x120 Bolt (4 pcs)
Parts
M14x120 Bolt (6 pcs)
M14 Nut (6 pcs)
M14 Washer (6 pcs)
D3-Holder (1 pcs)
N
N
N(mm) Part
1,500 D2-Holder (1500)
2,000 D2-Holder (2000)
2,500 D2-Holder (2500)
3,250 D2-Holder (3250)
3,500 D2-Holder (3500)
N(mm) Part
2,730 D3-Holder (2730)
3,730 D3-Holder (3730)
4,730 D3-Holder (4730)
6,230 D3-Holder (6230)
6,730 D3-Holder (6730)
Introduction Sets
Gable Endframe System – KSK
16
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
M - Front Extension Set
H - Telescopic Diagonal Set
Parts
Front Horizontal (1 pcs)
Timber Connector (2 pcs)
Bracket Connector (1 pcs)
Pin-Ø14x100 (3 pcs)
Spring Pin-2.5 (3 pcs)
Parts
Pin-Ø14x100 (2 pcs)
Spring Pin-2.5 (2 pcs)
Telescopic Prop (1 pcs)
Introduction Sets
Gable Endframe System – KSK
17
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
K - Lower Extension Set
J - Bracket Connector Set
L - Lower Platform Set
Parts
Spring Pin-2.5 (1 pcs)
Pin-Ø14x100 (1 pcs)
Lower Vertical (1 pcs)
Parts
Spring Pin-2.5 (1 pcs)
Bracket Connector (1 pcs)
Pin-Ø14x100 (1 pcs)
Parts
Pin-Ø14x115 (1 pcs)
Lower Diagonal (1 pcs)
Lower Horizontal (1 pcs)
Bracket Connector (1 pcs)
Pin-Ø14x100 (3 pcs)
Spring Pin-2.5 (4 pcs)
Introduction
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010
N - Holder Spacer Set
R - Support Spacer Set
Parts
Spring Pin-2.5 (2 pcs)
Holder Spacer (1 pcs)
Pin-Ø14x115 (2 pcs)
Parts
Spring Pin-2.5 (2 pcs)
Support Spacer (1 pcs)
Pin-Ø14x100 (2 pcs)
18
www.mesaimalat.com.tr
P - Holder End
S - Support End Set
2.5 (2 pcs)
Holder Spacer (1 pcs)
Ø14x115 (2 pcs)
Parts
Spring
Holder End (1 pcs)
Shoe Connector (1 pcs)
Pin-Ø14x115 (1 pcs)
2.5 (2 pcs)
Support Spacer (1 pcs)
Ø14x100 (2 pcs)
Parts
Spring Pin
Support End (1 pcs)
Pin-Ø14x100 (2 pcs)
Sets
Set
Support End Set
Parts
Spring Pin-2.5 (1 pcs)
Holder End (1 pcs)
Shoe Connector (1 pcs)
Ø14x115 (1 pcs)
Spring Pin-2.5 (2 pcs)
Support End (1 pcs)
Ø14x100 (2 pcs)
Introduction Dimensions
Gable Endframe System – KSK
19
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
L : Span Length of Triangular Brackets
N: Nominal Platform Length
X: Cantilever Length
P: Platform Length
Dimensions are in mm.
Refer to MESA advisory for other span
lengths listed above.
135mm ≤ X ≤ ( L / 2 )
P = X1 + X2 + L
N = 270 + L N = 270+2L P = X1 + X2 + 2L
For detailed information about cantilever
lengths, refer to section “Loading
Limits” on “User’s Manual”.
DIMENSIONS
Standart Spans
With Double-Triangular Bracket With Triple-Triangular Bracket
X min (mm) X max (mm) P min (mm) P max (mm)
1,500 135 615 1,500 2,460 1,230
2,000 135 865 2,000 3,460 1,730
2,500 135 1,115 2,500 4,460 2,230
3,250 135 1,490 3,250 5,960 2,980
X min (mm) X max (mm) P min (mm) P max (mm)
2,730 135 615 2,730 3,690 1,230
3,730 135 865 3,730 5,190 1,730
4,730 135 1,115 4,730 6,690 2,230
6,230 135 1,490 6,230 8,940 2,980
NOMINAL
PLATFORM
SIZE - N(mm)
SPAN
LENGTH
L (mm)
3-T
rian
gu
lar
Bra
cket NOMINAL
PLATFORM SIZE - N(mm)
SPAN
LENGTH L (mm)
2-
Tri
an
gu
lar
Bra
cket
CANTILEVER LENGTH - X PLATFORM LENGTH - P
CANTILEVER LENGTH - X PLATFORM LENGTH - P
Introduction Dimensions
Gable Endframe System – KSK
20
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
d : Slab Thickness
H : Distance between Ceiling and Tie-Rod
Y :Overall Platform Height
W :Effective Platform Depth
Standart Heights and Depths
Basic System Basic System +
Lower and Front Extension
Wmin=1800 mm Wmax=2825 mm
Ymin=2365 mm Ymax=4275 mm
Ymin 2365
2475
2675
2875
3075
3275
3475
3675
3875
4075
Ymax 4275
Adjustable Height
Range (mm)
Wmin 1800
2125
2295
2475
2645
Wmax 2825
Adjustable Depth Range (mm)
Introduction
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010
Do not use damaged or knotty woods.
P : Platform Length
W : Effective Platform Depth
t : Thickness of Timber Girder
w : Width of Timber Girder
y : Distance between two adjasent Girders
d : Slab Thickness
TIMBERS
Timber Girders
P w
t
P
y
21
www.mesaimalat.com.tr
Do not use damaged or knotty woods.
List of Platform Lengths “P” are
tabulated in the Section
on this Manual
between two adjasent Girders
Quantity
Dimensions
P y
Wmin
y ≤ (Wmax-Wmin)
Wmin = 1,800 mm
Wmax = 2,825 mm
t (mm)
65
w (mm)
200 d
250 180
Timbers
List of Platform Lengths “P” are
tabulated in the Section “Dimensions”
this Manual .
Wmax
y ≤ 600 mm
Quantity
1,800 mm 4 pcs.
2,825 mm 6 pcs.
d ≤ 180 mm
180 mm < d
Introduction
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010
P : Platform Length
W : Effective Platform Depth
t : Thickness of Timber Cover
w : Width of Timber Cover
Do not use damaged or knotty woods.
Timber Covers
t
w
W
P w
22
www.mesaimalat.com.tr
Do not use damaged or knotty woods.
List of Platform Lengths “P” are
tabulated in the Section
on this Manual
List of Effective Platform Depths “W” are
tabulated in the Section
on this Manual
Quantity
Dimensions
W
PW
min
w
No.of pieces = (P
t (mm)
50
w (mm)200 main
100 filler
Timbers
List of Platform Lengths “P” are
tabulated in the Section “Dimensions”
this Manual .
List of Effective Platform Depths “W” are
tabulated in the Section “Dimensions”
this Manual .
P
Wmax
No.of pieces = (P(mm) / 200(mm))
Introduction
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010
Do not use damaged or knotty woods.
P : Platform Length
W : Platform Width
t : Thickness of Guardrail Timber
w : Width of Guardrail Timber
S : Length of Guardrail Timber
Guardrail Timber
S w
t
W
S = W - 100
Side Guardrail Timber
23
www.mesaimalat.com.tr
Do not use damaged or knotty woods.
List of Effective Platform Depths “W”
and Platform Lengths “P” are tabulated
in the Section
Manual .
ber
Quantity
Dimensions
P
S = P100mm
Side Guardrail Timber Guardrail Timber
Guardrail Timbers
Side Guardrail Timbers
t (mm)
50
w (mm)
150
Timbers
List of Effective Platform Depths “W”
and Platform Lengths “P” are tabulated
in the Section “Dimensions” on this
S = P
Guardrail Timber
Quantity
Guardrail Timbers 4 pcs.
Side Guardrail Timbers 4 pcs.
Part List Basic Systems
Gable Endframe System – KSK
24
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
BASIC SYSTEMS
KSK-BASIC SYSTEM (with 2-Triangular Bracket)
LEGEND ID
Description PART NO PART NAME 1500 2000 2500 3250 3500
D2-Holder M.J.BKSK.1KT….. KSK-HOLDER (See Table) 1 1500 2000 2500 3250 3500
C2-Support M.J.BKSK.1KD….. KSK-SUPPORT (See Table) 1 1500 2000 2500 3250 3500
Bracket Horizontal M.M.KSKH.1K KSK-HORIZONTAL 32.17 2
Bracket Diagonal M.M.KSKD.1K KSK-INSIDE DIAGONAL 10.23 2
Bracket Vertical M.M.KSKV.1K KSK-VERTICAL 25.47 2
Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 2
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 4
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 6
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 10
M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 4
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.17 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 8
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 8
KSK-BASIC SYSTEM (with 3-Triangular Bracket)
LEGEND ID
Description PART NO PART NAME 2730 3730 4730 6230 6730
D3-Holder M.J.BKSK.1KT….. KSK-HOLDER (See Table) 1 2730 3730 4730 6230 6730
C3-Support M.J.BKSK.1KD….. KSK-SUPPORT (See Table) 1 2730 3730 4730 6230 6730
Bracket Horizontal M.M.KSKH.1K KSK-HORIZONTAL 32.17 3
Bracket Diagonal M.M.KSKD.1K KSK-INSIDE DIAGONAL 10.23 3
Bracket Vertical M.M.KSKV.1K KSK-VERTICAL 25.47 3
Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 3
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 6
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 9
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 15
M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 6
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.17 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 12
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 12
Support and Holder Lengths (mm)
MESA ID Unit Weight (kg)
NOMINAL PLATFORM SIZE - N (mm)Quantity per Set
MESA ID Unit Weight (kg)
Support and Holder Lengths (mm)
NOMINAL PLATFORM SIZE - N (mm)Quantity per Set
Part List Main System Sets
Gable Endframe System – KSK
25
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
MAIN SYSTEM SETS
LEGEND ID
Description PART NO PART NAME
Bracket Horizontal M.M.KSKH.1K KSK-HORIZONTAL 32.17 1
Bracket Diagonal M.M.KSKD.1K KSK-INSIDE DIAGONAL 10.23 1
Bracket Vertical M.M.KSKV.1K KSK-VERTICAL 25.47 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 1
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 4
TOTAL WEIGHT 68.49
Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 1
M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 2
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 2
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 2
TOTAL WEIGHT 6.75
Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 1
Side Guardrail Connector Z.B.H16E.0K1 16E-GUARDRAIL CONNECTOR (Type1) 3.19 1
M16x100 Bolt T.C.GM16.1S0100 HEXAGON BOLT-G (8.8) M16x100 0.20 2
M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 2
M16 Nut T.D.GM16.1S HEXAGON NUT-G (8.8) M16 0.03 2
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 2
M16 Washer T.P.PM16.S WASHER-G (M16) 0.01 2
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 2
TOTAL WEIGHT 10.42
Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 1
Mid.Guardrail Connector Z.B.HKSK.0K2 KSK-MID GUARDRAIL CONNECTOR 3.95 1
M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 2
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 2
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 2
TOTAL WEIGHT 10.70
A - KSK-TRIANGULAR BRACKET SET E.M.MKSK.0TB
MESA ID Unit Weight (kg)
Quantity per
Set
G - MID GUARDRAIL SET E.M.DHK1.0KQ
E - STANDARD GUARDRAIL SET E.M.DH15.0K
F - SIDE GUARDRAIL SET E.M.DHK1.0KY
Part List Main System Sets
Gable Endframe System – KSK
26
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
LEGEND ID
Description PART NO PART NAME
D2-Holder (1500) M.J.BKSK.1KT150 KSK-HOLDER (1500) 21.24 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 4
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 4
TOTAL WEIGHT 21.96
D2-Holder (2000) M.J.BKSK.1KT200 KSK-HOLDER (2000) 27.10 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 4
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 4
TOTAL WEIGHT 27.82
D2-Holder (2500) M.J.BKSK.1KT250 KSK-HOLDER (2500) 32.95 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 4
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 4
TOTAL WEIGHT 33.67
D2-Holder (3250) M.J.BKSK.1KT325 KSK-HOLDER (3250) 41.73 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 4
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 4
TOTAL WEIGHT 42.45
D2-Holder (3500) M.J.BKSK.1KT350 KSK-HOLDER (3500) 44.65 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 4
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 4
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 4
TOTAL WEIGHT 45.37
D2 - KSK-HOLDER SET (1500) E.M.MKSK.0KH215
D2 - KSK-HOLDER SET (3500) E.M.MKSK.0KH235
MESA ID Unit Weight (kg)
Quantity per
Set
D2 - KSK-HOLDER SET (3250) E.M.MKSK.0KH232
D2 - KSK-HOLDER SET (2500) E.M.MKSK.0KH225
D2 - KSK-HOLDER SET (2000) E.M.MKSK.0KH220
Part List Main System Sets
Gable Endframe System – KSK
27
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
LEGEND ID
Description PART NO PART NAME
D3-Holder (2730) M.J.BKSK.1KT273 KSK-HOLDER (2730) 36.00 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 6
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 6
TOTAL WEIGHT 37.08
D3-Holder (3730) M.J.BKSK.1KT373 KSK-HOLDER (3730) 49.20 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 6
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 6
TOTAL WEIGHT 50.28
D3-Holder (4730) M.J.BKSK.1KT473 KSK-HOLDER (4730) 60.91 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 6
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 6
TOTAL WEIGHT 61.99
D3-Holder (6230) M.J.BKSK.1KT623 KSK-HOLDER (6230) 78.47 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 6
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 6
TOTAL WEIGHT 79.55
D3-Holder (6730) M.J.BKSK.1KT673 KSK-HOLDER (6730) 84.32 1
M14x120 Bolt T.C.GM14.1S0120 HEXAGON BOLT-G (8.8) M14x120 0.14 6
M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 6
M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 6
TOTAL WEIGHT 85.40
D3 - KSK-HOLDER SET (2730) E.M.MKSK.0KH327
D3 - KSK-HOLDER SET (4730) E.M.MKSK.0KH347
D3 - KSK-HOLDER SET (3730) E.M.MKSK.0KH337
D3 - KSK-HOLDER SET (6730) E.M.MKSK.0KH367
D3 - KSK-HOLDER SET (6230) E.M.MKSK.0KH362
MESA ID Unit Weight (kg)
Quantity per
Set
Part List Main System Sets
Gable Endframe System – KSK
28
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
LEGEND ID
Description PART NO PART NAME
C2-Support (1500) M.J.BKSK.1KD150 KSK-SUPPORT (1500) 13.13 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 13.41
C2-Support (2000) M.J.BKSK.1KD200 KSK-SUPPORT (2000) 17.15 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 17.43
C2-Support (2500) M.J.BKSK.1KD250 KSK-SUPPORT (2500) 21.18 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 21.46
C2-Support (3250) M.J.BKSK.1KD325 KSK-SUPPORT (3250) 27.22 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 27.50
C2-Support (3500) M.J.BKSK.1KD350 KSK-SUPPORT (3500) 29.24 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 29.52
C2 - KSK-SUPPORT SET (1500) E.M.MKSK.0KS215
C2 - KSK-SUPPORT SET (3500) E.M.MKSK.0KS235
MESA ID Unit Weight (kg)
Quantity per
Set
C2 - KSK-SUPPORT SET (3250) E.M.MKSK.0KS232
C2 - KSK-SUPPORT SET (2500) E.M.MKSK.0KS225
C2 - KSK-SUPPORT SET (2000) E.M.MKSK.0KS220
Part List Main System Sets
Gable Endframe System – KSK
29
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
LEGEND ID
Description PART NO PART NAME
C3-Support (2730) M.J.BKSK.1KD273 KSK-SUPPORT (2730) 23.14 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 23.42
C3-Support (3730) M.J.BKSK.1KD373 KSK-SUPPORT (3730) 31.61 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 31.89
C3-Support (4730) M.J.BKSK.1KD473 KSK-SUPPORT (4730) 39.67 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 39.95
C3-Support (6230) M.J.BKSK.1KD623 KSK-SUPPORT (6230) 51.75 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 52.03
C3-Support (6730) M.J.BKSK.1KD673 KSK-SUPPORT (6730) 55.75 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 56.03
E.M.MKSK.0KS327C3 - KSK-SUPPORT SET (2730)
C3 - KSK-SUPPORT SET (4730) E.M.MKSK.0KS347
C3 - KSK-SUPPORT SET (3730) E.M.MKSK.0KS337
C3 - KSK-SUPPORT SET (6230) E.M.MKSK.0KS362
C3 - KSK-SUPPORT SET (6730) E.M.MKSK.0KS367
MESA ID Unit Weight (kg)
Quantity per
Set
Part List Tie-Shoe Sets
Gable Endframe System – KSK
30
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
TIE-SHOE SETS
LEGEND ID
Description PART NO PART NAME
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (350) Z.S.TQKS.0E035 KSK-SHOE TIE(20FAx350)-E 1.13 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 12.36
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (450) Z.S.TQKS.0E045 KSK-SHOE TIE(20FAx450)-E 1.45 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 12.68
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (500) Z.S.TQKS.0E050 KSK-SHOE TIE(20FAx500)-E 1.62 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 12.85
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (750) Z.S.TQKS.0E075 KSK-SHOE TIE(20FAx750)-E 2.43 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 13.66
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (1000) Z.S.TQKS.0E100 KSK-SHOE TIE(20FAx1000)-E 3.20 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 14.43
Shoe M.J.AKSK.0K KSK-SHOE 9.57 1
Shoe-Tie (1500) Z.S.TQKS.0E150 KSK-SHOE TIE(20FAx1500)-E 4.87 1
Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1
Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1
Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1
TOTAL WEIGHT 16.10
B - KSK-SHOE SET (350) E.M.JAKS.0K035
B - KSK-SHOE SET (500) E.M.JAKS.0K050
MESA ID Unit Weight (kg)
Quantity per
Set
B - KSK-SHOE SET (1500) E.M.JAKS.0K150
B - KSK-SHOE SET (750) E.M.JAKS.0K075
B - KSK-SHOE SET (1000) E.M.JAKS.0K100
B - KSK-SHOE SET (450) E.M.JAKS.0K045
Part List Anchor-Shoe Sets
Gable Endframe System – KSK
31
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
ANCHOR-SHOE SETS
LEGEND ID
Description PART NO PART NAME
Anchor Shoe M.J.AKSK.0KB KSK-ANCHOR SHOE 9.32 1
Anchor Screw Z.A.DB50.16024 CONICAL SCREWED ANCHOR-48x160 (M24) 1.40 1
M24x70 Bolt T.C.GM24.1S0070 HEXAGON BOLT-G (8.8) M24x70 0.40 1
M24 Washer T.P.PM24.S WASHER-G (M24) 0.01 1
TOTAL WEIGHT 11.13
MESA ID Unit Weight (kg)
Quantity per
Set
B - KSK/ANCHOR-SHOE SET (350) E.M.JAKS.0KB160
Part List Extension Sets
Gable Endframe System – KSK
32
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
EXTENSION SETS
LEGEND ID
Description PART NO PART NAME
Telescopic Prop M.J.BKSK.1KBD KSK-TELESCOPIC PROP 18.32 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 18.60
Lower Vertical M.J.BKSK.1KLU KSK-LOWER EXTENSION 11.73 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 1
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 1
TOTAL WEIGHT 11.87
Lower Diagonal M.J.BKSK.2KLB KSK-WALKING PLT.DIAGONAL 18.98 1
Lower Horizontal M.J.BKSK.1KLP KSK-WALKING PLT.HORIZONTAL 7.00 1
Bracket Connector Z.B.JKSK.0K01 KSK-BRACKET CONNECTOR 1.85 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 1
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 4
TOTAL WEIGHT 28.41
Front Horizontal M.J.BKSK.2KLB KSK-WALKING PLT.DIAGONAL 18.98 1
Timber Connector A.M.KSK9.0K KSK-TIMBER CONNECTOR 1.95 2
Bracket Connector Z.B.JKSK.0K01 KSK-BRACKET CONNECTOR 1.85 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 3
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 3
TOTAL WEIGHT 25.15
Bracket Connector Z.B.JKSK.0K01 KSK-BRACKET CONNECTOR 1.85 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 1
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 1
TOTAL WEIGHT 1.99
H - TELESCOPIC DIAGONAL SET E.M.MKSK.0KDK
MESA ID Unit Weight (kg)
Quantity per
Set
L - LOWER PLATFORM SET E.M.MKSK.0KBG
K - LOWER EXTENSION SET E.M.MKSK.0KBU
J - BRACKET CONNECTOR SET E.M.MKSK.0KDB
M - FRONT EXTENSION SET E.M.MKSK.0KFU
Part List Platform-to-Platform Connections
Gable Endframe System – KSK
33
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Suffix “-E “ on the Part Name means that
Part is Electro Galvanised.
Suffix “-G “ on the Part Name means that
Part is Hot Deep Galvanised.
For ordering, use MESA ID “PART NO”s
and MESA ID “PART NAME”s of Sets,
Assemblies and any other unique parts.
PLATFORM-to-PLATFORM CONNECTIONS
LEGEND ID
Description PART NO PART NAME
Holder Spacer M.J.BKSK.1KTAA KSK-HOLDER SPACER 21.12 1
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 21.44
Holder End M.J.BKSK.1KTUA KSK-HOLDER END 19.08 1
Shoe Connector Z.B.JKSK.0K06 KSK-SHOE CONNECTOR 3.58 1
Pin-Ø14x115 Z.C.PKSK.0E01 KSK-PIN (14x115)-E 0.15 1
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 1
TOTAL WEIGHT 22.67
Support Spacer M.J.BKSK.1KDAA KSK-SUPPORT SPACER 10.35 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 2
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 2
TOTAL WEIGHT 10.63
Support End M.J.BKSK.1KDUA KSK-SUPPORT END 7.61 1
Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 1
Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 1
TOTAL WEIGHT 7.75
N - KSK-Holder Spacer SET E.M.MKSK.0KTA
MESA ID Unit Weight (kg)
Quantity per
Set
P - KSK-Holder End SET E.M.MKSK.0KTU
E.M.MKSK.0KDUS - KSK-Support End SET
R - KSK-Support Spacer SET E.M.MKSK.0KDA
Notes
Gable Endframe System – KSK
TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr
Top Related