Y Customizable feeler gauge - media.prusaprinters.org · 108.9 KB updated 26. 5. 2020 142.9 KB...
Transcript of Y Customizable feeler gauge - media.prusaprinters.org · 108.9 KB updated 26. 5. 2020 142.9 KB...
Summary
When designing something I often need to get an idea of what a dimensionfeels like for real and even if I can set it on the caliper it isn't enough. Idesigned this in fusion allowing for customization (the files have to becreated one by one though), the current set has the values from 0.2mm to1.0mm with increments of 0.1mm; the values from 1.0mm to 5.0mm withincrements of 0.5mm and the values from 5.0mm to 10.0mm withincrements of 1mm.
All the parts have their thickess engraved for easier identification apartfrom the 0.2mm one which was too thin.
A perfect first layer is required to print the thinnest ones and some trialsmay be necessary to get to the right size.
The parts are kept together by a screw with 2 ends which tightly screw inplace. 2 copies of the end are needed.
I included also 2 washers to place between the gauges and the ends but Idon't think they are required
Hobby & Makers > Tools
gauge feelergauges design
V Vivi
Customizablefeeler gauge
VIEW IN BROWSER
updated 26. 5. 2020 | published 26. 5. 2020
3D M
ODEL
ONLY
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
116.1 KBupdated 26. 5. 2020
29.6 KBupdated 26. 5. 2020
90.2 KBupdated 26. 5. 2020
126.1 KBupdated 26. 5. 2020
96.0 KBupdated 26. 5. 2020
114.3 KBupdated 26. 5. 2020
THE SCREW HAS TO BE PRINTED FLAT.
Without too much effort I have been able to get all the parts within +-0.05mm of precision.
In the files section you can find the single files and 3 assembliescontaining more than one part for easier print (named something like 01-to-09.stl).
I suggest using 0.2mm layer height for the first layer. For the thinnerpieces 0.1mm layer height is required while for the other 0.2mm is enough
08.stl
02.stl
07.stl
03.stl
04.stl
15.stl
108.9 KBupdated 26. 5. 2020
142.9 KBupdated 26. 5. 2020
130.9 KBupdated 26. 5. 2020
113.0 KBupdated 26. 5. 2020
98.3 KBupdated 26. 5. 2020
127.4 KBupdated 26. 5. 2020
112.9 KBupdated 26. 5. 2020
123.2 KBupdated 26. 5. 2020
122.7 KBupdated 26. 5. 2020
05.stl
35.stl
30.stl
50.stl
10.stl
60.stl
09.stl
25.stl
90.stl
111.3 KBupdated 26. 5. 2020
124.9 KBupdated 26. 5. 2020
116.9 KBupdated 26. 5. 2020
114.9 KBupdated 26. 5. 2020
57.7 KBupdated 26. 5. 2020
1.0 MBupdated 26. 5. 2020
103.0 KBupdated 26. 5. 2020
104.8 KBupdated 26. 5. 2020
436.3 KBupdated 26. 5. 2020
20.stl
80.stl
06.stl
45.stl
washer.stl
10-to-50.stl
40.stl
70.stl
screw.stl
147.6 KBupdated 26. 5. 2020
627.1 KBupdated 26. 5. 2020
796.0 KBupdated 26. 5. 2020
492.9 KBupdated 26. 5. 2020
2.4 MBupdated 26. 5. 2020
Find source .stl files on Thingiverse.com
The Author has not uploaded any print files.Try to search in User print files section or generate and upload yourown.
License
This work is licensed under a Creative Commons (4.0 International License)
Attribution
100.stl
60-to-100.stl
02-to-09.stl
cap.stl
02-to-100.stl
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✔ | Commercial Use ✔ | Free Cultural Works ✔ | Meets Open Definition