W.i chain guide
12
HPM WORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date Rev 5LU1100000-2401-008 Inspection Page Specification : Refer to singe part checksheet Prepared By : Approved By : Acknowledge By : Doc. Controller QA In - Charge SBM / SPL
Transcript of W.i chain guide
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 1 OF 6
Specification : Refer to singe part checksheet
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 2 OF 6
Specification : Refer to singe part checksheet = item inspection checksheet
Check use Plug Gauge Spec : 4.02~4.07 mm Check use Plug Gauge Spec : 4.42~4.47 mmCek dengan Plug Gauge Spec : 4.02~4.07 mm Cek dengan Plug Gauge Spec : 4.42~4.47 mm
Check use Plug Gauge Spec : 3.62~3.67 mm Check use Plug Gauge Spec : 5.50~5.70 mmCek dengan Plug Gauge Spec : 3.62~3.67 mm Cek dengan Plug Gauge Spec : 5.50~5.70 mm
Check use Plug Gauge Spec : 3.47~3.52 mmCek dengan Plug Gauge Spec : 3.47~3.52 mm
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
1
2
3
4
5
PG 4.02~4.07mm
PG 3.62~3.67mm
PG 3.47~3.52mm
PG 4.42~4.47mm
PG 5.50~5.70mm
XX
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 3 OF 6
Specification : Refer to singe part checksheet = item inspection checksheet
Check use Caliper Spec : 2.5~3.5 mm Check use Caliper Spec : 3.9~4.1 mmCek dengan Caliper spec 2.5~3.5 mm Cek dengan Caliper Spec 3.9~4.1 mm
Check use Caliper Spec : >1.9 mm Check use Caliper Spec : > 2.5 mmCek dengan Caliper Spec : >1.9 mm
Check use Caliper Spec : >2.3 mm (arround)Cek dengan Caliper Spec : >2.3 mm (keliling)
Check use Caliper Spec : 1.2 mmCek dengan Caliper Spec : 1.2 mm
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
Cek dengan Caliper Spec : > 2.5 mm
2 side checking
27
28
29
30
31
32
XX
Burr Height
Material Thickness
Outer Ø checking
wall thickness checkinghole - outline part
wall thickness checkinghole - outline part
Side 1 Side 2 Side 2 Side 1
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE
Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 4 OF 6
Specification : Refer to singe part checksheet = item inspection checksheet
Prepare Jig FDM191-ST-CGIP-PR01 A,B, C, D, & ESiapkan Jig FDM191-ST-CGIP-PR01 A, B, C, D, & E
Method
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
AB C DE
E
B
C
D
Cek Go-No Go Jig
7
XX
21
Must free up and down
11
Must Flat, filler gauge 0.3 mm not go in
01
Put spacer t=0.7 mm below part
Monthly Prodn Code and Under Line Check
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 5 OF 6
Specification : Refer to singe part checksheet = item inspection checksheet
Siapkan Jig FDM191-ST-CGIP-PC01 F, G, H, I, J, K, & L
Method
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
F
H GI
J (2pcs)K
L
F
H
G
I
J (2pcs)
L
K ( Cek No Go )K ( Cek Go )
FDM191-ST-CGIP-PC01 set + Part
12
1313
14
15
16
17
18
19
20
23
24 25
XX
HPMWORK INSTRUCTION CHECKING METHOD CHAIN GUIDE Date 5-May-10
Rev 01
5LU1100000-2401-008 Inspection Page 6 OF 6
Specification : Refer to singe part checksheet = item inspection checksheet
Siapkan Jig FDM191-ST-CGIP-PC01 M, N, O
Method
Prepared By : Approved By : Acknowledge By :
Doc. Controller QA In - Charge SBM / SPL
if Jig FDM191ST-CGIP-PC01 with part OK put item OK
M
N O
N
O
M
FDM191-ST-CGIP-PC01 set + Part
FDM191-ST-CGIP-PC01 set + Part
22
XX
6
9
8
10
26
