VESDA Commissioning Forms VLP Rev01
description
Transcript of VESDA Commissioning Forms VLP Rev01
-
VESDA Commissioning Form This is the main commissioning form for each customer site. Customer Name
Site Address
Installer (Name & Contact)
Commissioner (Name & Contact)
Checks Date:
1. Wiring Checked 2. Detector Diagnostics 3. Display Diagnostic 4. Test Relays
1. 2. 3. 4.
Client Representative Name Test Witnessed By
Date:
Hand Over Documents 1. Copy of this form 2. ASPIRE2 Installation Data Pack 3. ASPIRE2 Bill of Materials 4. Commissioning form for each detector 5. Commissioning form for each relay card 6. Smoke test results 7. Ancillary devices form 8. Forms to comply with the local codes & standards
1. 2. 3. 4. 5. 6. 7. 8.
Customer's Signature
Date: Commissioner's Signature
Date:
-
VLP_Commissioning_Forms.doc
LaserPLUS Detector Commissioning Form For all VESDAnet systems, highlight the device, the zone or VESDAnet then select File Print to file. Address Set up
Reference Detector Address No.
Thresholds Dilution% Day Alert Delay in Seconds
Action Simultaneous/Cumulative Simultaneous/ Cumulative
Fire 1 Instant Fire Enable/Disable Fire 2 Smoke Change
% %
Night Alert Airflow Action Raw Flow Pipe 1 Fire 1 Pipe 2 Fire 2 Pipe 3 Delay Alert Pipe 4 Action % Flow Pipe 1 Fire 1 Pipe 2 Fire 2 Pipe 3 Filter
Service Period
Pipe 4
Flow Threshold High Urgent %
Maximum Transport Time
Pipe 1 seconds
High Minor %
Pipe 2 seconds Low
Minor % Pipe 3 seconds
Low Urgent %
Pipe 4 seconds Delay in
Seconds Aspirator
Speed 3000-4200 rpm
-
VESDAVLPRelayConfiguration7Relayterminationcards
Yrepresentsthedefaultrelaysettings.Relay3and6arepermanentlyconfiguredformajorfaultandfire1.Allotherrelayscanbereconfigured.Morethanonefunctioncanbeconfiguredtoarelay.PlaceYinrelevantboxtoindicatethefunctionforwhichtherelayhasbeenconfigured.D=Deenergized;E=Energized;B=Beeper;L=Latching
Relay
1 2 3 4 5 6 7
Startup
D E E D D D D B L
Configuration
Isolate
Y Y
Minorfault
Y Y Y
MajorFault
Y Y Y
Alert
Y Y Y
Action
Y Y Y
Fire1
Y Y Y
Fire2
Y Y Y
-
ASPIRE2Data:
Display/RelayModuleConfiguration:
GroupName
AggregateSensitivity Balance SuctionPressure EndcapSensitivityfactor
DisplayModuleNo.
Mode/Test
Silence/Scan
Reset
Isolate
RelaysConnectedYes/No
IsolateReminderYes/No
-
AncillaryDevices:
VESDAZoneNo.
VESDAZoneName
DeviceName
DeviceNo.
SoftwareVersion
Location
SmokeTest:
TestResult
TestMethod
TypeofSmoke
TestDate
-
AirSampling:
Note:TheAsbuiltASPIRE2calculationstobeattached
PipeNo.
1 2 3 4
TestType TransportTimefromEndofCap
Test1
IntialResponse
Alert
Action/PreAlarm
Fire1/Fire
Fire2
PeakSmoke
Test2
TransportTimefromEndofCap
IntialResponse
Alert
Action/PreAlarm
Fire1/Fire
Fire2
PeakSmoke
-
NOTE