USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... ·...

75
1.03-03302018-171400 USER MANUAL ARTiGO-A1200 Barebone System with EITX-2000 Embedded Board

Transcript of USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... ·...

Page 1: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

1.03-03302018-171400

USER MANUAL

ARTiGO-A1200 Barebone System with EITX-2000

Embedded Board

Page 2: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Copyright Copyright © 2013 VIA Technologies Incorporated. All rights reserved.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,

in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written

permission of VIA Technologies, Incorporated.

Trademarks All trademarks are the property of their respective holders.

Disclaimer No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no

warranties, implied or otherwise, in regard to this document and to the products described in this document. The information

provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA

Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra

device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document.

The information and product specifications within this document are subject to change at any time, without notice and without

obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior

notice.

Regulatory Compliance FCC-A Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his

personal expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Notice 3

The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts

or damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before

placing an order.

Page 3: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

Battery Recycling and Disposal � Only use the appropriate battery specified for this product.

� Do not re-use, recharge, or reheat an old battery.

� Do not attempt to force open the battery.

� Do not discard used batteries with regular trash.

� Discard used batteries according to local regulations.

Safety Precautions � Always read the safety instructions carefully.

� Keep this User's Manual for future reference.

� All cautions and warnings on the equipment should be noted.

� Keep this equipment away from humidity.

� Lay this equipment on a reliable flat surface before setting it up.

� Make sure the voltage of the power source and adjust properly 110/220V before connecting

the equipment to the power inlet.

� Place the power cord in such a way that people cannot step on it.

� Always unplug the power cord before inserting any add-on card or module.

� If any of the following situations arises, get the equipment checked by authorized service

personnel:

� The power cord or plug is damaged.

� Liquid has penetrated into the equipment.

� The equipment has been exposed to moisture.

� The equipment has not worked well or you cannot get it work according to User's Manual.

� The equipment has dropped and damaged.

� The equipment has obvious sign of breakage.

� Do not leave this equipment in an environment unconditioned or in a storage temperature

above 60°C (140°F). The equipment may be damaged.

� Do not leave this equipment in direct sunlight.

� Never pour any liquid into the opening. Liquid can cause damage or electrical shock.

� Do not place anything over the power cord.

� Do not cover the ventilation holes. The openings on the enclosure protect the equipment

from overheating

Page 4: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

iv

Box Content � 1 x ARTiGO-A1200 system

� 1 x AC-to-DC adapter, DC 12V/5A, 60W

� 1 x Power cable

� 1 x Installation Guide

Ordering Information

Part Number Description

ATG-1200-1D12A1 VIA EdenTM X2 1.0GHz processor based Fanless Embedded

system, with 1 x VGA, 1 x HDMI®, 4x USB 2.0, 1 x USB 3.0

(optional), 2 x GigaLAN, 2 x COM (RS-232), 1 x Line-Out, 1 x Mic-

In, 1 x CFast socket, 1 x 2.5 HDD bay and DC-In 12V, power cord

USA type.

ATG-A1200-2D10A1 VIA EdenTM X2 1.0GHz processor based Fanless Embedded

system, with 1 x VGA, 1 x HDMI®, 4x USB 2.0, 1 x USB 3.0

(optional), 2 x GigaLAN, 2 x COM (RS-232), 1 x Line-Out, 1 x Mic-

In, 1 x CFast socket, 1 x 2.5 HDD bay and DC-In 12V, power cord

EU type.

ATG-A1200-3D10A1 VIA EdenTM X2 1.0GHz processor based Fanless Embedded

system, with 1 x VGA, 1 x HDMI®, 4x USB 2.0, 1 x USB 3.0

(optional), 2 x GigaLAN, 2 x COM (RS-232), 1 x Line-Out, 1 x Mic-

In, 1 x CFast socket, 1 x 2.5 HDD bay and DC-In 12V, power cord

Japan type.

ATG-A1200-4D10A1 VIA EdenTM X2 1.0GHz processor based Fanless Embedded

system, with 1 x VGA, 1 x HDMI®, 4x USB 2.0, 1 x USB 3.0

(optional), 2 x GigaLAN, 2 x COM (RS-232), 1 x Line-Out, 1 x Mic-

In, 1 x CFast socket, 1 x 2.5 HDD bay and DC-In 12V, power cord

China type.

Page 5: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

v

Optional Accessories

RAM Module Part Number Description

99G06-010901 2GB DDR3-1333, 256M x 8bits SODIMM, Industrial Grade,

0°C ~ 85°C

99G06-010911 4GB DDR3-1333, 256M x 8bits SODIMM, Industrial Grade,

0°C ~ 85°C

Flash Disk Part Number Description

99G61-060244 2GB CFast Flash Disk, SATA II, Quad Channel, Industrial Grade,

-40°C ~ 85°

99G61-060254 4GB CFast Flash Disk, SATA II, Quad Channel, Industrial Grade,

-40°C ~ 85°

2.5-inch Hard Disk Drive Part Number Description

99G61-020173 320G SEAGATE SATA II HD, 0°C ~ 60°C

Note:

The optional accessories may have minimum ordering quantity limitation. Please contact VIA Sales

representative for more details.

Page 6: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

vi

Table of Contents

1. Product Overview ................................................................................................ 1

1.1. Key Features ................................................................................................... 1

1.1.1. Compact, Fanless, Ultra-slim and Space Saving .................................. 1

1.1.2. Optimize integration with dual sided I/O access ............................ 1

1.1.3. Wide Range of Operating Temperatures........................................... 2

1.1.4. Display Acceleration .............................................................................. 2

1.1.5. Shock Resistant ........................................................................................ 2

1.1.6. Networking Support ............................................................................... 2

1.1.7. Embedded OS ready ............................................................................. 2

1.2. Product Specifications ................................................................................. 3

1.3. ARTiGO-A1200 Dimensions ...................................................................... 7

1.4. ARTiGO-A1200 Layout ............................................................................... 8

2. External I/O Pin Descriptions and Functionality ............................................... 9

2.1. Front Panel ..................................................................................................... 9

2.1.1. Power Button ........................................................................................... 9

2.1.2. LED Indicators (Power LED and HDD LED) ...................................... 9

2.1.3. VGA Connector ..................................................................................... 10

2.1.4. HDMI® Port ............................................................................................. 11

2.1.5. USB 3.0 Port ........................................................................................... 12

2.1.6. LAN Port: Gigabit Ethernet ................................................................. 13

2.1.7. CFast Socket ........................................................................................... 14

2.2. Rear Panel .................................................................................................... 15

2.2.1. Power Input (DC-In) Jack .................................................................... 15

2.2.2. COM Connector .................................................................................... 16

2.2.3. USB 2.0 Port ........................................................................................... 17

2.2.4. Audio Jacks ............................................................................................. 18

3. Hardware Installation ........................................................................................ 19

3.1. Installing the Memory ............................................................................... 19

Page 7: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

vii

3.2. Installing CFast Card .................................................................................. 21

3.3. Installing 2.5-inch SATA Hard Disk ........................................................ 22

3.4. Inserting 3G SIM Card ............................................................................... 24

3.5. Installing 3G and WLAN kit ..................................................................... 25

3.6. Installing the Chassis Top Cover ............................................................ 27

4. Jumpers ............................................................................................................... 29

4.1. Clear CMOS Jumper .................................................................................. 29

5. BIOS Setup Utility .............................................................................................. 31

5.1. Entering the BIOS Setup Utility ............................................................... 31

5.2. Control Keys ................................................................................................ 31

5.3. Navigating the BIOS Menus ..................................................................... 32

5.4. Getting Help................................................................................................ 32

5.5. Main Menu ................................................................................................... 33

5.5.1. Standard CMOS Features .................................................................... 33

5.5.2. Advanced BIOS Features ..................................................................... 33

5.5.3. Advanced Chipset Features ................................................................ 33

5.5.4. Integrated Peripherals .......................................................................... 33

5.5.5. Power Management Setup .................................................................. 34

5.5.6. PnP/PCI Configurations ......................................................................... 34

5.5.7. PC Health Status .................................................................................... 34

5.5.8. Frequency/Voltage Control ................................................................ 34

5.5.9. Load Optimized Defaults .................................................................... 34

5.5.10. Set Supervisor Password ..................................................................... 34

5.5.11. Set User Password ................................................................................ 34

5.5.12. Save & Exit Setup .................................................................................. 34

5.5.13. Exit Without Saving............................................................................... 34

5.6. Standard CMOS Features ......................................................................... 35

5.6.1. Date .......................................................................................................... 35

5.6.2. Time ......................................................................................................... 35

5.6.3. IDE Channel 0 Master/ IDE Channel 0 Slave .................................. 35

5.6.4. Halt On ................................................................................................... 36

Page 8: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

viii

5.7. Advanced BIOS Features .......................................................................... 37

5.7.1. Quick Power On Self-Test .................................................................. 37

5.7.2. First/Second/Third Boot Device ......................................................... 38

5.7.3. Boot Other Device ................................................................................ 38

5.7.4. Boot Up NumLock Status .................................................................... 38

5.7.5. Typematic Rate Setting ........................................................................ 38

5.7.6. Typematic Rate (Chars/Sec) ................................................................ 38

5.7.7. Typematic Delay (Msec) ..................................................................... 39

5.7.8. Security Option ..................................................................................... 39

5.7.9. Full Screen Logo Show ........................................................................ 39

5.7.10. Summary Screen Show ........................................................................ 39

5.8. CPU Feature ................................................................................................. 40

5.8.1. Thermal Management .......................................................................... 40

5.9. Hard Disk Boot Priority .............................................................................. 41

5.10. Advanced Chipset Features ..................................................................... 42

5.10.1. OnBoard PCIE LAN ............................................................................... 42

5.10.2. EuP/ErP Lot6 ........................................................................................... 42

5.10.3. Hide D1F1 ............................................................................................... 43

5.11. UMA & P2P Bridge Control ...................................................................... 44

5.11.1. VGA Share Memory Size ..................................................................... 44

5.11.2. Select Display Device 1 ...................................................................... 44

5.11.3. Select Display Device 2 ...................................................................... 45

5.12. Integrated Peripherals ............................................................................... 46

5.12.1. OnChip SATA ........................................................................................ 46

5.12.2. OnChip HDAC Device ......................................................................... 46

5.12.3. WatchDog support ............................................................................... 46

5.12.4. NB HDAudio Codec 1 ......................................................................... 47

5.13. SuperIO Device .......................................................................................... 48

5.13.1. Onboard Serial Port 1 .......................................................................... 48

5.13.2. Onboard Serial Port 2 .......................................................................... 48

5.13.3. COM2 422/485 flow control ............................................................. 48

5.14. USB Device Setting .................................................................................... 49

5.14.1. USB 1.0 Controller................................................................................ 49

Page 9: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

ix

5.14.2. USB 2.0 Controller................................................................................ 49

5.14.3. USB Operation Mode ........................................................................... 49

5.14.4. USB Keyboard Function ....................................................................... 50

5.14.5. USB Storage Function ........................................................................... 50

5.15. Power Management Setup ....................................................................... 51

5.15.1. ACPI Suspend Type .............................................................................. 51

5.15.2. Soft-Off by PWRBTN ............................................................................ 51

5.15.3. Run VGABIOS if S3 Resume ............................................................... 52

5.15.4. AC Loss Auto Restart ........................................................................... 52

5.15.5. VX900 USB S4 WakeUp ...................................................................... 52

5.15.6. HPET Support ........................................................................................ 52

5.15.7. WDRT Support ...................................................................................... 52

5.15.8. WDRT Run/Stop..................................................................................... 52

5.15.9. WDRT Count .......................................................................................... 52

5.16. Wakeup Event Detect ................................................................................ 53

5.16.1. RTC Alarm Resume ............................................................................... 53

5.16.2. Date (of Month) ..................................................................................... 53

5.16.3. Resume Time (hh : mm : ss) ............................................................... 53

5.17. PnP/PCI Configurations .............................................................................. 54

5.17.1. Init Display First ..................................................................................... 54

5.17.2. Reset Configuration Data ..................................................................... 54

5.17.3. Resources Controlled By ..................................................................... 55

5.17.4. PCI/VGA Palette Snoop ....................................................................... 55

5.18 PC Health Status ......................................................................................... 56

5.18. Frequency/Voltage Control ..................................................................... 57

5.18.1. DRAM Clock ........................................................................................... 57

5.19. Load Optimized Defaults ......................................................................... 58

5.20. Set Supervisor/User Password ................................................................. 59

5.21. Save & Exit Setup ....................................................................................... 61

5.22. Exit Without Saving .................................................................................... 62

6. Driver Installation ............................................................................................... 63

6.1. Microsoft Driver Support .......................................................................... 63

Page 10: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

x

6.2. Linux Driver Support.................................................................................. 63

Page 11: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

xi

Lists of Figures Figure 1: Dimensions of the ARTiGO-A1200 (front view) ....................................... 7

Figure 2: Dimensions of the ARTiGO-A1200 (side view) ........................................ 7

Figure 3: Front Panel layout ............................................................................................ 8

Figure 4: Rear Panel layout .............................................................................................. 8

Figure 5: Left Side Panel layout ...................................................................................... 8

Figure 6: Power button switch diagram ....................................................................... 9

Figure 7: Power and HDD LED indicator diagrams .................................................... 9

Figure 8: VGA connector pinout diagram .................................................................. 10

Figure 9: HDMI® port pinout diagram ......................................................................... 11

Figure 10: USB 3.0 port pinout diagram ..................................................................... 12

Figure 11: Gigabit Ethernet port pinout diagram ..................................................... 13

Figure 12: CFast socket diagram ................................................................................... 14

Figure 13: Power input jack diagram ........................................................................... 15

Figure 14: COM port pinout diagram ......................................................................... 16

Figure 15: USB 2.0 port pinout diagram ..................................................................... 17

Figure 16: Audio jack receptacle stack diagram ....................................................... 18

Figure 17: CLEAR CMOS jumper ................................................................................. 29

Figure 18: Illustration of the Main menu screen ....................................................... 33

Page 12: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

xii

Lists of Tables Table 1: VGA connector pinout .................................................................................. 10

Table 2: HDMI® port pinout ......................................................................................... 11

Table 3: USB 3.0 port pinout ........................................................................................ 12

Table 4: Gigabit Ethernet port pinout ........................................................................ 13

Table 5: Gigabit Ethernet LED color definition ........................................................ 13

Table 6: Power input jack pinout................................................................................. 15

Table 7: COM ports pinout .......................................................................................... 16

Table 8: USB 2.0 port pinout ........................................................................................ 17

Table 9: Audio jack receptacle description .............................................................. 18

Table 10: CLEAR CMOS jumper settings ................................................................... 29

Page 13: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

1

1. Product Overview The VIA ARTiGO-A1200 is a compact, ultra-slim and fanless embedded

system with an elegant chassis design. The ARTiGO-A1200 is based on the VIA

EITX-2000 board and powered by high performance dual core 64-bit VIA

Eden™ X2 1.0GHz processor which is superb in multi-tasking performance,

high power computing operation with lower power consumption. The

ARTiGO-A1200 is fully compatible with Microsoft® and Linux operating

systems.

The ARTiGO-A1200 supports intensive dual sided I/O connectors such as USB

ports, VGA port, HDMI® port, COM ports, GigaLAN ports, CFast socket and

audio ports for diversified embedded applications. In addition, the ARTiGO-

A1200 offers an expanding option for WLAN and 3G connectivity through

onboard miniPCIe with one SIM socket.

The ARTiGO-A1200’s system chassis is a robust aluminum alloy with

removable top cover, bottom plate; front and rear I/O access plates.

1.1. Key Features

1.1.1. Compact, Fanless, Ultra-slim and Space Saving The ARTiGO-A1200 has an ultra slim and compact aluminum chassis, designed

to save space that makes it suitable to install in space critical environment and

to ensure maximum reliability. It is also a completely fanless system operation

using the heatsink fins as a thermal solution.

1.1.2. Optimize integration with dual sided I/O access Front and rear I/O access enables the ARTiGO-A1200 to easily support various

applications as well as for easy integration and quick setup.

Page 14: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

2

1.1.3. Wide Range of Operating Temperatures The ARTiGO-A1200 carries a qualified thermal performance design which

allows a wide range of operating temperatures from 0°C up to 45°C.

1.1.4. Display Acceleration The ARTiGO-A1200 supports hardware acceleration of MPEG-2, WMV9/VC1

and H.264 for 1080p full HD display.

1.1.5. Shock Resistant The ARTiGO-A1200 is shock resistant to 10G for maximum reliability.

1.1.6. Networking Support The ARTiGO-A1200 is equipped with two RJ-45 ports that support Gigabit

Ethernet. The ARTiGO-A1200 also has WLAN and 3G module options that

give the ARTiGO-A1200 a freedom of WiFi access and 3G network

connectivity through miniPCIe module.

1.1.7. Embedded OS ready The ARTiGO-A1200 is 100% compatible with several operating systems

including Microsoft Windows 7, Widows XP, Windows XP Embedded,

Windows Embedded Standard, Windows Embedded Standard 7 and Linux.

Page 15: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

3

1.2. Product Specifications � Processor Core Logic System

� CPU

VIA Eden™ X2 1.0GHz processor

� 1066MHz Front Side Bus speed

� 2 MB L2 Cache memory

� NanoBGA2 package

� Chipset

VIA VX900 Unified Digital Medial IGP chipset

� 31 mm x 31 mm FCBGA

� System Memory

1 x SODIMM slot supporting DDR3 1066 SDRAM

� Supports up to 4 GB memory size

� BIOS

Award

8 Mbit SPI flash memory

� System Power Management

Times Power On

ACPI supported

� Graphics

� Controller

Integrated VIA C-9 HD DX9 3D/2D Graphics and Video Processor

Integrated Unified Video Decoding Accelerator for MPEG-2, WMV9/VC1, and

H.264

� Display Memory

Optimized Shared Memory Architecture (UMA), supports up to 512MB frame

buffer using system memory

� CRT Interface

Supports one VGA connector

Supports up to 2560 x 1600 of pixel resolution

� HDMI® Interface

Supports one HDMI® port

� Dual Independent Display

Two independent display engines built in VX900 chipset,

Page 16: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

4

Supports dual independent display of CRT + HDMI® at different resolutions, pixel

depths, and refresh rates

� Dual Gigabit Ethernet

� Controller

Onboard dual VIA VT6130 Gigabit Ethernet controllers

� Interface

Two RJ-45 ports

Supports Wake On LAN (WOL)

Supports Pre-boot Execution Environment (PXE)

� High Definition Audio

� Controller

VIA VT2021 Blue-Ray High Definition Audio Codec

� Interface

Supports two 3.5ф Audio Jack as Line-Out and Mic-In

� USB 2.0

� Controller

Integrated USB 2.0 host controller built-in VX900 IGP chipset on system board

� Interface

Supports four USB 2.0 ports

� USB 3.0 (Optional support)

� Controller

VIA VL801 USB 3.0 host controller

� Interface

Supports one USB 3.0 port

� Serial Ports

� Controller

Fintek F81801 LPC I/O controller

� Interface

Supports two RS-232 as default of COM1 and COM2 connectors

Optional support of RS-422/RS-485 at COM1 connector

� Storage Interface

� Hard Disk Drive

Built-in one 2.5” hard disk drive bay for 2.5” SATA HDD or 2.5” Flash SSD

� CFast

Built-in one CFast socket for Type I/II of CFast Flash disk

Page 17: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

5

� System Indicator

� Power Status LED

One green color LED

� HDD Activity LED

One red color LED

� Watchdog Timer

� Output

System reset

� Interval

Programmable 1 ~ 255 sec.

� External I/O connectors

� Front I/O panel

One Power On/Off Button Switch

One color green Power Status LED

One color red HDD Activity LED

One VGA connector (D-sub 15-pin female connector)

One HDMI® port

One USB 3.0 port (optional)

Two RJ-45 GigaLAN connectors

One CFast flash disk socket

� Rear I/O panel

One DC jack power input connector

Two COM connectors (default as RS-232)

Four USB 2.0 ports

Two 3.5ф Audio Jack connectors as Line-Out and Mic-In

� Left side I/O panel

Two reserved antenna holes for WLAN and 3G miniPCIe adapters

� Power Supply

� Power Input Connector

One tamper-proof DC jack power input connector

� Power Consumption

Typical 20.86W, Maximum 27.51W

� Input Voltage

Built-in system DC-to-DC converter

DC 12V Power Input

Support ATX mode

� Fuse Rating

7A @ 125V

Page 18: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

6

� Mechanical Power Supply

� Construction

Aluminum chassis housing

� Mounting

Optional support of Wall/Table/VESA mounting bracket

� Dimension (W x H x D)

234 mm x 30 mm x 124 mm

� Weight

1.2 Kg. (net weight)

� Environmental Specification

� Operating Temperature

0°C up to 45°C

� Storage Temperature

-20°C to 60°C @ 90°C, non-condensing

� Relative Humidity

0% ~ 90% @ 45°C, non-condensing

� Vibration Loading during operation (the system is running with CFast flash disk only)

1Grms, IEC 60068-2-64, random, 5~500Hz, 1 Oct./min, 1 hr/axis

� Shock Loading during operation (the system is running with CFast flash disk only)

10G, IEC 60068-2-27, half size, 11ms duration

� Software Compatibility (Operating System)

Microsoft Windows 7

Microsoft Windows XP

Microsoft Windows XP Embedded

Microsoft Windows Embedded Standard

Microsoft Windows Embedded Standard 7

Linux

Page 19: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

7

1.3. ARTiGO-A1200 Dimensions

Figure 1: Dimensions of the ARTiGO-A1200 (front view)

Figure 2: Dimensions of the ARTiGO-A1200 (side view)

Page 20: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

8

1.4. ARTiGO-A1200 Layout

Figure 3: Front Panel layout

Figure 4: Rear Panel layout

Figure 5: Left Side Panel layout

Page 21: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

9

2. External I/O Pin Descriptions

and Functionality The VIA ARTiGO-A1200 has a wide selection of interfaces located on the

front and rear panels as part of the external I/O.

2.1. Front Panel

2.1.1. Power Button The ARTiGO-1200 comes with a Power On/Off button, that supports Soft

Power-On/Off (Instant Off or 4 second delay) and Suspend.

Figure 6: Power button switch diagram

2.1.2. LED Indicators (Power LED and HDD LED) There are two LEDs on the front panel that indicate the system status:

� PWR LED flashes in green and indicates the status of the system’s

power status.

� HDD LED flashes in red and indicates any storage activity for the CFast

card and HDD.

Figure 7: Power and HDD LED indicator diagrams

Page 22: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

10

2.1.3. VGA Connector The ARTiGO-A1200 provides a high resolution VGA interface through a 15-pin

D-sub female connector to support analog VGA monitors. It supports up to

2560 x 1620 @ 60Hz resolution and up to 512 MB shared memory.

Figure 8: VGA connector pinout diagram

Pin Signal

1 Red

2 Green

3 Blue

4 NC

5 GND

6 GND

7 GND

8 GND

9 NC

10 GND

11 NC

12 DDC DAT

13 H-SYNC

14 V-SYNC

15 DDC CLK

Table 1: VGA connector pinout

Page 23: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

11

2.1.4. HDMI® Port The ARTiGO-A1200 provides a HDMI® (High Definition Multimedia Interface)

port for connecting to high definition video and digital audio. The HDMI® port

connector allows you to connect digital video devices which utilize a high

definition video signal. The pinout of the HDMI® port is shown below.

Figure 9: HDMI® port pinout diagram

Pin Signal Pin Signal

1 TX2+ 2 GND

3 TX2- 4 TX1+

5 GND 6 TX1-

7 TX0+ 8 GND

9 TX0- 10 TXC+

11 GND 12 TXC-

13 - 14 -

15 DDCSCL 16 DDCSDA

17 GND 18 +5V

19 Hot Plug Detect

Table 2: HDMI® port pinout

Page 24: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

12

2.1.5. USB 3.0 Port The ARTiGO-1200 is equipped with USB 3.0 port, also known as SuperSpeed

USB on the front panel. The USB 3.0 port has a maximum data transfer rate up

to 5 Gbps and offers a backwards compatible with previous USB 2.0

specifications. It gives complete Plug and Play and hot swap capability for

external devices. The pinout of the typical USB 3.0 port is shown below.

Figure 10: USB 3.0 port pinout diagram

Pin Signal

1 +5V

2 Data-

3 Data+

4 Ground

5 Rx-

6 Rx+

7 Ground

8 Tx-

Tx+

Table 3: USB 3.0 port pinout

Page 25: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

13

2.1.6. LAN Port: Gigabit Ethernet The ARTiGO-A1200 system is equipped with two Gigabit Ethernet ports

(LAN1 and LAN2) on front panel. Both ports are fully compliant with IEEE

802.3 (10BASE-T), 802.3u (100BASE-TX), and 802.3ab (1000BASE-T) standards.

The pinout of the LAN1 and LAN2 ports are shown below

Figure 11: Gigabit Ethernet port pinout diagram

LAN1 LAN2

Pin Signal Pin Signal

1 LAN1_TD0+ 1 LAN2_TD0+

2 LAN1_TD0- 2 LAN2_TD0-

3 LAN1_TD1+ 3 LAN2_TD1+

4 LAN1_TD1- 4 LAN2_TD1-

5 LAN1_TD2+ 5 LAN2_TD2+

6 LAN1_TD2- 6 LAN2_TD3-

7 LAN1_TD3+ 7 LAN2_TD3+

8 LAN1_TD3- 8 LAN2_TD3-

Table 4: Gigabit Ethernet port pinout

The LAN port (RJ-45) has two individual LED indicators located on the front

side to show its Active/Link status and Speed status.

Link LED

(Left LED on RJ-45 connector)

Active LED

(Right LED on RJ-45 connector)

Link Off Off Off

Speed_10Mbit The LED is always On in either Green

or Orange colors Flash in Yellow color

Speed_100Mbit The LED is always On in Green color Flash in Yellow color

Speed_1000Mbit The LED is always On in Orange color Flash in Yellow color

Table 5: Gigabit Ethernet LED color definition

Page 26: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

14

2.1.7. CFast Socket The ARTiGO-A1200 is equipped with CFast socket on the front panel for CFast

card storage device. The CFast socket is compatible with Type I and Type II

CFast card.

Figure 12: CFast socket diagram

Page 27: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

15

2.2. Rear Panel

2.2.1. Power Input (DC-In) Jack The ARTiGO-A1200 comes with a DC power input jack on the real panel that

carries 12VDC. External power input.

Figure 13: Power input jack diagram

Pin Signal

1 GND

2 12VDC

Table 6: Power input jack pinout

Page 28: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

16

2.2.2. COM Connector The ARTiGO-A1200 system is equipped with two COM connectors named

COM1 and COM2 on the rear panel. Both COM connectors are configured as

RS-232 serial communication. The pinout of the COM1 and COM2 connectors

ports are shown below

Figure 14: COM port pinout diagram

COM1 COM2

Pin Signal Pin Signal

1 DCD 1 DCD

2 RxD 2 RxD

3 TxD 3 TxD

4 DTR 4 DTR

5 GND 5 GND

6 DSR 6 DSR

7 RTS 7 RTS

8 CTS 8 CTS

9 RI 9 RI

Table 7: COM ports pinout

Page 29: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

17

2.2.3. USB 2.0 Port The ARTiGO-A1200 provides four USB 2.0 ports in the rear panel for Plug &

Play and hot swapping access to external devices. The USB interface complies

with USB UHCI, Rev. 2.0.

Figure 15: USB 2.0 port pinout diagram

Pin Signal

1 VCC

2 USB_PO-

3 USB_PO+

4 GND

Table 8: USB 2.0 port pinout

Page 30: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

18

2.2.4. Audio Jacks The ARTiGO-A1200 offers High Definition Audio through two 3.5 mm TRS jack

connectors: Line-out and Mic-in.

The Line-out jack is for connecting to external speakers or headphones. The

Mic-in jack is for connecting to a microphone.

Figure 16: Audio jack receptacle stack diagram

Jack Description

Mic-In TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded

Line-Out TRS jack, 3.5mm Ø 5P, 90 Degree, Female, shielded

Table 9: Audio jack receptacle description

Page 31: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

19

3. Hardware Installation This chapter provides you with information about hardware installation

procedures. It is recommended to use a grounded wrist strap before handling

computer components. Electrostatic discharge (ESD) can damage some

components.

3.1. Installing the Memory Step 1

Remove the top cover from the chassis by unscrewing the ten screws to locate

the DDR3 SODIMM memory socket.

Page 32: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

20

Step 2

Locate the DDR3 SODIMM memory socket. Gently insert the DDR3 memory

module into the SODIMM socket at a 30 degrees angle. Push down the

memory module until it snaps into place.

Step 3

Flip over the top cover. Then remove the memory thermal pad protective

cover (plastic) on the memory heatsink.

Page 33: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

21

3.2. Installing CFast Card Step 1

Remove the CFast socket cover by unscrewing the two screws.

Step 2

Insert the CFast card into the CFast socket. Ensure the proper orientation

before inserting the card. Then reinstall the CFast socket cover.

Page 34: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

22

3.3. Installing 2.5-inch SATA Hard Disk

Step 1

On the bottom side of the top cover, remove the SATA 2.5” hard disk drive

brackets.

Step 2

Attach the brackets to the 2.5-inch SATA hard disk then secure it with four

screws.

Page 35: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

23

Step 3

Reinstall the brackets with 2.5” SATA hard disk by aligning the brackets on the

standoff mounting holes. Then secure the brackets with four screws.

Step 4

Connect the SATA data and power cables into the system board and connect

the other end of the cables into the 2.5” SATA hard disk.

Page 36: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

24

3.4. Inserting 3G SIM Card

Step 1

Push back firmly the SIM card socket to unlock and open. Pull up the socket

and place the SIM card in the socket.

Note:

Ensure the angled corner of the SIM card is placed in the correct way before closing the socket.

Step 2

Gently close the socket by pulling down the SIM socket containing with SIM

card then carefully lock the SIM slot as indicated in the figures.

Page 37: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

25

3.5. Installing 3G and WLAN kit

Step 1

Align the notch on the miniPCIe (3G/WLAN) module with the notch on the

miniPCIe slot then insert the module at a 30° angle.

Step 2

Once the module has been fully inserted, push down the module until the

screw hole align with the standoff hole then secure the module with screw.

Page 38: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

26

Step 3

Locate the 3G/WLAN antenna holes at the rear side of the chassis. Insert the

3G/WLAN port connectors into the antenna holes from the inside of the

chassis. Insert the washer and fasten it with the nut then install the external

antenna.

Step 4

Gently connect the mini coaxial cables of the 3G/WLAN port connectors to

the mini RF connectors on the 3G/WLAN miniPCIe module.

Page 39: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

27

3.6. Installing the Chassis Top Cover Align and install the top cover with the chassis and secure it with ten screws.

Page 40: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,
Page 41: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

29

4. Jumpers

4.1. Clear CMOS Jumper The onboard CMOS RAM stores system configuration data and has an onboard

battery power supply. To reset the CMOS settings, set the jumper on pins 2

and 3 while the system is off. Return the jumper to pins 1 and 2 afterwards.

Setting the jumper while the system is on will damage the mainboard. The

default setting is on pins 1 and 2.

Figure 17: CLEAR CMOS jumper

Setting Pin 1 Pin 2 Pin 3

Regular (default) On On Off

Clear CMOS Off On On

Table 10: CLEAR CMOS jumper settings

Note:

Except when clearing the RTC RAM, never remove the cap from the CLEAR_CMOS jumper default

position. Removing the cap will cause system boot failure. Avoid clearing the CMOS while the system

is on; it will damage the mainboard.

Page 42: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,
Page 43: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

31

5. BIOS Setup Utility

5.1. Entering the BIOS Setup Utility Power on the computer and press Delete during the beginning of the boot

sequence to enter the BIOS Setup Utility. If the entry point has passed, restart

the system and try again.

5.2. Control Keys Up Move up one row

Down Move down one row

Left Move to the left in the navigation bar

Right Move to the right in the navigation bar

Enter Access the highlighted item / Select the item

Esc Jumps to the Exit screen or returns to the previous screen

Page up / +1 Increase the numeric value

Page down / -1 Decrease the numeric value

F1 General help2

F5 Restore the previous CMOS value

F7 Load optimized defaults

F10 Save all the changes and exit

Note:

1. Must be pressed using the 10-key pad.

2. The General help contents are only for the Status Page and Option Page setup menus.

Page 44: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

32

5.3. Navigating the BIOS Menus The main menu displays all the BIOS setup categories. Use the <Left>/<Right>

and <Up>/<Down> arrow keys to select any item or sub-menu. Descriptions

of the selected/highlighted category are displayed at the bottom of the screen.

The small triangular arrowhead symbol next to a field indicates that a sub-

menu is available (see figure below). Press <Enter> to display the sub-menu.

To exit the sub-menu, press <Esc>.

5.4. Getting Help The BIOS Setup Utility provides a “General Help” screen. This screen can be

accessed at any time by pressing F1. The help screen displays the keys for

using and navigating the BIOS Setup Utility. Press Esc to exit the help screen.

Page 45: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

33

5.5. Main Menu The Main Menu contains eleven setup functions and two exit choices. Use

arrow keys to select the items and press <Enter> to accept or enter Sub-menu.

Figure 18: Illustration of the Main menu screen

5.5.1. Standard CMOS Features Use this menu to set basic system configurations.

5.5.2. Advanced BIOS Features Use this menu to set the advanced features available on your system.

5.5.3. Advanced Chipset Features Use this menu to set chipset specific features and optimize system

performance.

5.5.4. Integrated Peripherals Use this menu to set onboard peripherals features.

Page 46: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

34

5.5.5. Power Management Setup Use this menu to set onboard power management functions.

5.5.6. PnP/PCI Configurations Use this menu to set the PnP and PCI configurations.

5.5.7. PC Health Status This menu shows the PC health status.

5.5.8. Frequency/Voltage Control Use this menu to set the system frequency and voltage control.

5.5.9. Load Optimized Defaults Use this menu option to load BIOS default settings for optimal and high

performance system operations.

5.5.10. Set Supervisor Password Use this menu option to set the BIOS supervisor password.

5.5.11. Set User Password Use this menu option to set the BIOS user password.

5.5.12. Save & Exit Setup Save BIOS setting changes and exit setup.

5.5.13. Exit Without Saving Discard all BIOS setting changes and exit setup.

Page 47: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

35

5.6. Standard CMOS Features

5.6.1. Date The date format is [Month, Date, Year]

5.6.2. Time The time format is [Hour : Minute : Second]

5.6.3. IDE Channel 0 Master/ IDE Channel 0 Slave The specifications of your drive must match with the drive table. The hard disk

will not work properly if you enter incorrect information in this category.

Select “Auto” whenever possible. If you select “Manual”, make sure the

information is from your hard disk vendor or system manufacturer.

Below is a table that details required hard drive information when using the

“Manual” mode.

Page 48: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

36

Settings Description

[storage] Channel The name of this match the name of the menu.

Settings: [None, Auto, Manual]

Access Mode Settings: [CHS, LBA, Large, Auto]

Capacity Formatted size of the storage device

Cylinder Number of cylinders

Head Number of heads

Precomp Write precompensation

Landing Zone Cylinder location of the landing zone

Sector Number of sectors

5.6.4. Halt On Set the system’s response to specific boot errors. Below is a table that details

the possible settings.

Settings Description

All Errors System halts when any error is detected

No Errors System does not halt for any error

All, But Keyboard System halts for all non-key errors

Page 49: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

37

5.7. Advanced BIOS Features

The Advanced BIOS Features section includes the following submenus:

� CPU Feature

� Hard Disk Boot Priority

5.7.1. Quick Power On Self-Test Shortens Power On Self-Test (POST) cycle to enable shorter boot up time.

Settings Description

Disabled Standard Power On Self Test (POST)

Enabled Shorten Power On Self Test (POST) cycle and boot up time

Page 50: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

38

5.7.2. First/Second/Third Boot Device Set the boot device sequence as BIOS attempts to load the disk operating

system.

Settings Description

Removable Boot from external drive

Hard Disk Boot from the HDD

CDROM Boot from CDROM

Legacy LAN Boot from network drive

VIA Networking Boot from network drive

Disabled Disable the boot device sequence

5.7.3. Boot Other Device Enables the system to boot from alternate devices if the system fails to boot

from the “First/Second/Third Boot Device” lists.

Settings Description

Disabled No alternate boot device allowed

Enabled Enable alternate boot device

5.7.4. Boot Up NumLock Status Set the NumLock status when the system is powered on.

Settings Description

Off Forces keypad to behave as arrow keys

On Forces keypad to behave as 10-key

5.7.5. Typematic Rate Setting Enables “Typematic Rate” and “Typematic Delay” functions.

Settings: [Disabled, Enabled]

5.7.6. Typematic Rate (Chars/Sec) This item sets the rate (characters/second) at which the system retrieves a

signal from a depressed key.

Settings: [6, 8, 10, 12, 15, 20, 24, 30]

Page 51: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

39

5.7.7. Typematic Delay (Msec) This item sets the delay between, when the key was first pressed and when

the system begins to repeat the signal from the depressed key.

Settings: [250, 500, 750, 1000]

5.7.8. Security Option Selects whether the password is required every time the System boots, or only

when you enter Setup.

Settings Description

Setup Password prompt appears only when end users try to run BIOS

Setup

System Password prompt appears every time when the computer is powered

on and when end users try to run BIOS Setup

5.7.9. Full Screen Logo Show Show full screen logo during BIOS boot up process.

Settings: [Disabled, Enabled]

5.7.10. Summary Screen Show Show summary screen.

Settings: [Disabled, Enabled]

Page 52: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

40

5.8. CPU Feature

5.8.1. Thermal Management This item sets CPU’s thermal control rule to protect CPU from overheat.

Settings Description

Thermal Monitor 1 On-die throtting

Thermal Monitor 2 Ratio & VID transition

Thermal Monitor 3 Dynamic Ratio & VID transition

Page 53: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

41

5.9. Hard Disk Boot Priority

This is for setting the priority of the hard disk boot order when the “Hard Disk”

option is selected in the “[First/Second/Third] Boot Device” menu item.

Page 54: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

42

5.10. Advanced Chipset Features

Caution:

The Advanced Chipset Features menu is used for optimizing the chipset functions. Do not change

these settings unless you are familiar with the chipset.

The Advanced Chipset Features section includes the following submenu:

� UMA & P2P Bridge Control

5.10.1. OnBoard PCIE LAN Settings: [Enabled, Disabled]

5.10.2. EuP/ErP Lot6 The EuP/ErP Lot6 Support feature enables the BIOS to reduce the power draw

to less than 1W when the system is in standby mode. This feature has two

options: Enabled and Disabled.

Page 55: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

43

Note:

When EuP/ErP Lot6 support is enabled, the PCIe LAN remote wake-up capability will be disabled.

5.10.3. Hide D1F1 Settings: [Enabled, Disabled]

Page 56: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

44

5.11. UMA & P2P Bridge Control

5.11.1. VGA Share Memory Size This setting allows you to select the amount of system memory that is

allocated to the integrated graphics processor.

Settings Description

128M Maximum amount of memory that can be allocated to the graphics

processor if the system memory size is less than 1GB.

256M Maximum amount of memory that can be allocated to the graphics

processor if the system memory size is 1GB but less than 2GB.

512M Maximum amount of memory that can be allocated to the graphics

processor if the system memory size is 2GB or above.

5.11.2. Select Display Device 1 This setting refers to the type of display device 1 being used with the system.

Settings: [CRT, HDMI]

Page 57: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

45

5.11.3. Select Display Device 2 This setting refers to the type of display device 2 being used with the system.

Settings: [CRT, HDMI]

Page 58: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

46

5.12. Integrated Peripherals

The Integrated Peripherals section includes the following submenus:

� SuperIO Device

� USB Device Setting

5.12.1. OnChip SATA Settings: [Disabled, Enabled]

5.12.2. OnChip HDAC Device The OnChip HDAC Device feature enables the BIOS to control the high

definition audio codec in the chipset. This feature has two options: Enabled

and Disabled.

5.12.3. WatchDog support The WatchDog support feature unlocks two other features that enable the

BIOS to monitor the state of the system. This feature has two options: Enabled

or Disabled.

Page 59: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

47

5.12.4. NB HDAudio Codec 1 The NB HDAudio Codec 1 feature enables the BIOS to control the high

definition audio codec in the chipset. This feature has two options: “Enabled”

and “Disabled”

Page 60: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

48

5.13. SuperIO Device

5.13.1. Onboard Serial Port 1 Settings: [Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]

5.13.2. Onboard Serial Port 2 Settings: [Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]

5.13.3. COM2 422/485 flow control Settings: [RS232, RS422, RS485]

Page 61: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

49

5.14. USB Device Setting

5.14.1. USB 1.0 Controller Enable or disable Universal Host Controller Interface for Universal Serial Bus.

Settings: [Disabled, Enabled]

5.14.2. USB 2.0 Controller Enable or disable Enhanced Host Controller Interface for Universal Serial Bus.

Settings: [Disabled, Enabled]

5.14.3. USB Operation Mode Auto decide USB device operation mode.

Settings Description

Full/Low Speed All of USB Device operated on full/low speed mode

High Speed If USB device was high speed device, then it operated on high speed

mode.

Page 62: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

50

5.14.4. USB Keyboard Function Enable or disable legacy support of USB keyboard.

Settings: [Disabled, Enabled]

5.14.5. USB Storage Function Enable or disable legacy support of USB mass storage.

Settings: [Disabled, Enabled]

Page 63: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

51

5.15. Power Management Setup

The Power Management Setup section includes the following submenus:

� Wakeup Event Detect

5.15.1. ACPI Suspend Type Settings Description

S1(POS) S1/Power On Suspend (POS) is a low power state. In this state, no

system context (CPU or chipset) is lost and hardware maintains all system

contexts.

S3(STR) S3/Suspend To RAM (STR) is a power-down state. In this state, power is

supplied only to essential components such as main memory and

wakeup-capable devices. The system context is saved to main memory,

and context is restored from the memory when a "wakeup" event occurs.

S1 & S3 Depends on the OS to select S1 or S3.

5.15.2. Soft-Off by PWRBTN Settings Description

Delay 4 Sec System is turned off if power button is pressed for more than four

seconds.

Instant-Off Power button functions as a normal power-on/-off button.

Page 64: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

52

5.15.3. Run VGABIOS if S3 Resume Select whether to run VGA BIOS if resuming from S3 state. This is only

necessary for older VGA drivers.

Settings: [Auto, Yes, No]

5.15.4. AC Loss Auto Restart The field defines how the system will respond after an AC power loss during

system operation.

Settings Description

Off Keeps the system in an off state until the power button is pressed

On Restarts the system when the power is back

Former-Sts Former-Sts

5.15.5. VX900 USB S4 WakeUp Settings: [Disabled, Enabled]

5.15.6. HPET Support Settings: [Disabled, Enabled]

5.15.7. WDRT Support Settings: [Disabled, Enabled]

5.15.8. WDRT Run/Stop Settings: [Stop, Run]

5.15.9. WDRT Count Settings: [Min = 0, Max = 1023]

Page 65: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

53

5.16. Wakeup Event Detect

5.16.1. RTC Alarm Resume Set a scheduled time and/or date to automatically power on the system.

Settings: [Disabled, Enabled]

5.16.2. Date (of Month) The field specifies the date for “RTC Alarm Resume”.

Key in a DEC number.

Settings: [Min = 0, Max = 31]

5.16.3. Resume Time (hh : mm : ss) The field specifies the time for “RTC Alarm Resume”.

Key in a DEC number.

Settings: [Min = 0, Max = 23]

Page 66: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

54

5.17. PnP/PCI Configurations

Note:

This section covers some very technical items and it is strongly recommended to leave the default

settings as is unless you are an experienced user.

5.17.1. Init Display First Settings: [PCI slot, Onboard, PCIEx]

5.17.2. Reset Configuration Data Settings Description

Disabled Default setting

Enabled Resets the ESCD (Extended System Configuration Data) after

exiting BIOS Setup if a newly installed PCI card or the system

configuration prevents the operating system from loading

Page 67: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

55

5.17.3. Resources Controlled By Enables the BIOS to automatically configure all the Plug-and-Play compatible

devices.

Settings Description

Auto(ESCD) BIOS will automatically assign IRQ, DMA and memory base

address fields

Manual Unlocks “IRQ Resources” for manual configuration

5.17.4. PCI/VGA Palette Snoop Some non-standard VGA display cards may not show colors properly. This field

allows you to set whether MPEG ISA/VESA VGA Cards can work with PCI/VGA

or not. When enabled, a PCI/VGA can work with a MPEG ISA/VESA VGA card.

When disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.

Settings: [Disabled, Enabled]

Page 68: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

56

5.18 PC Health Status

The PC Health Status displays the current status of all of the monitored

hardware devices/components such as CPU voltages and temperatures.

Page 69: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

57

5.18. Frequency/Voltage Control

5.18.1. DRAM Clock This chipset supports synchronous and asynchronous mode between host

clock and DRAM clock frequency.

Settings: [By SPD, 400 MHz, 533 MHz]

Page 70: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

58

5.19. Load Optimized Defaults

This option is for restoring all the default optimized BIOS settings. The default

optimized values are set by the mainboard manufacturer to provide a stable

system with optimized performance.

Entering “Y” and press <Enter> to load the default optimized BIOS values.

Entering ”N” will cancel the load optimized defaults request.

Page 71: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

59

5.20. Set Supervisor/User Password

This option is for setting a password for entering BIOS Setup. When a

password has been set, a password prompt will be displayed whenever BIOS

Setup is run. This prevents an unauthorized person from changing any part of

your system configuration.

There are two types of passwords you can set. A supervisor password and a

user password. When a supervisor password is used, the BIOS Setup program

can be accessed and the BIOS settings can be changed. When a user

password is used, the BIOS Setup program can be accessed but the BIOS

settings cannot be changed.

To set the password, type the password (up to eight characters in length) and

press <Enter>. The password typed now will clear any previously set

password from CMOS memory. The new password will need to be reentered

to be confirmed. To cancel the process press <Esc>.

To disable the password, press <Enter> when prompted to enter a new

password. A message will show up to confirm disabling the password. To

cancel the process press <Esc>.+

Page 72: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

60

Additionally, when a password is enabled, the BIOS can be set to request the

password each time the system is booted. This would prevent unauthorized

use of the system. See “Security Option” in the “Advanced BIOS Features”

section for more details.

Page 73: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

61

5.21. Save & Exit Setup

Entering “Y” saves any changes made, and exits the program.

Entering “N” will cancel the exit request.

Page 74: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

62

5.22. Exit Without Saving

Entering “Y’ discards any changes made and exits the program.

Entering “N” will cancel the exit request

Page 75: USER MANUAL ARTiGO-A1200cdn.viaembedded.com/eol_products/docs/artigo_a1200/user_manual/UM... · ARTiGO -A1200 User Manual iv Box Content 1 x ARTiGO-A1200 system 1 x AC-to-DC adapter,

ARTiGO-A1200 User Manual

63

6. Driver Installation

6.1. Microsoft Driver Support The VIA ARTiGO-A1200 mainboard is compatible with Microsoft operating

systems. The latest Windows drivers can be downloaded from the VIA

Embedded website at www.viaembedded.com.

For embedded operating systems, the related drivers can be found in the VIA

Embedded website at www.viaembedded.com.

6.2. Linux Driver Support The VIA ARTiGO-A1200 mainboard is highly compatible with many Linux

distributions.

Support and drivers are provided through various methods including:

� Drivers provided by VIA

� Using a driver built into a distribution package

� Visiting www.viaembedded.com for the latest updated drivers

� Installing a third party driver (such as the ALSA driver from the

Advanced Linux Sound Architecture project for integrated audio)

For OEM clients and system integrators developing a product for long term

production, other code and resources may also be made available. Contact

VIA Embedded to submit a request.