Universal Storage Pedestal Service Parts · 1. Insert the rear hook of the slide into the rear...
Transcript of Universal Storage Pedestal Service Parts · 1. Insert the rear hook of the slide into the rear...
Page 1 of 11939503077 Rev B
If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2008 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
Universal Storage Pedestal Service Parts
Table of Contents
Page Topic
2 Outer Head Replacement
3 Drawer Removal
4 Drawer Removal If Slides Are Not
Being Removed
5 Slide Removal�
6 Slide Re-Assembly
7 Lock Bar Installation
8 Interlock Installation
9 Lock Rod Installation
10 Drawer Lock Component Removal�
11 Drawer Re-Assembly�
7/8" Deep Socket
Page 2 of 11939503077 Rev B
2a
2b
1
SIDE
Outer Head Replacement
NOTE: Pedestal removed for clarity.��
1. Remove all screws from each side of drawer.
2. Slide outer head up (2a) and away (2b) from drawer.
3. Reverse previous steps to re-assemble.
Page 3 of 11939503077 Rev B
Drawer Removal
NOTE: If slides are not going to be removed, follow instructions on page 4.
1. Remove drawer screw from each side for 30" deep file drawers only.
2. Pull drawer forward (2a). Push emboss out (2b) and lift drawer up to disengage from belt loops left and right (2c).
3. Pull drawer forward to disengage from the rear hook.
3
2bNOTE: Pedestal removed for clarity.
2c
1
2a
Page 4 of 11939503077 Rev B
1
2
Drawer Removal If Slides Are Not Being Removed
1. Pull drawer forward.
2. Push on tab on each side of the drawer rails.
3. Remove drawer completely.
4. Push drawer rails back into pedestal.
5. Remove remaining drawers.��TIP: Mark all drawers so they can be easily re-installed in their original positions.
3
4
Page 5 of 11939503077 Rev B
Slide Removal
1. For the right hand slide, place a flat bladed screwdriver (from the top) between the slide and the pedestal body (making sure to place the screwdriver onto the side channel of the pedestal body) (1a). Rotate slide in a counterclockwise direction, away from the pedestal body (1b) then lift towards the screwdriver to disengage (1c).��
2. Pull slide forward to disengage from the rear.
3. Repeat steps 1 & 2 for left hand slide except the screwdriver is located from the bottom (3a, 3b & 3c).
2
LEFT HAND�SHOWN
RIGHT HAND�SHOWN
1b
1a 1c
3c
3b
3a
Page 6 of 11939503077 Rev B
Slide Re-Assembly��NOTE: Slides NOT to be installed with a hammer.��
1. Insert the rear hook of the slide into the rear bracket of the pedestal body.
2. For the right hand slide, hook the slide into the square hole on the front bracket of the pedestal body (2a) and PRESS DOWN to snap the slide into position (2b).��TIP: Pull slide out to gain better leverage.��
3. For the left hand side, repeat steps 1 & 2 except you need to LIFT UP to snap the slide into position (3a & 3b).
1
2a
2b
RIGHT HAND�SHOWN
LEFT HAND�SHOWN
3a
3b
Page 7 of 11939503077 Rev B
Lock Bar Installation�
1. Insert the lock bar into the front four (4) rectangular slots of the pedestal body.
2. Turn lock bar inward (2a) while aligning all eight (8) lances with the eight (8) rectangular slots (2b) and slide downward.
3. Place lock bar spring under frame lip.
1
LOCK BAR
FRAME LIP
LOCK BARSPRING
3
2a
2b
RECTANGULARSLOT
LANCE
Page 8 of 11939503077 Rev B
Interlock Installation
1. Line up the holes on the interlock module with matching holes on the pedestal body.
2. Drive a screw in each hole.
TIP: Drive the top screw halfway (2a), then drive the remaining three (3) screws all the way down (2b) and then finish the top screw.
3. Replace the old trigger on the drawers with the new trigger provided.
INTERLOCKMODULE
FRAME
TOP SCREW
1
2a
2b
2b
2b
Page 9 of 11939503077 Rev B
Lock Rod Installation
1. Remove outer head on drawer (perform steps 1 and 2 on page 2).
2. Assemble lock rod as follows:
a) Align lock rod with front of drawer as shown.
b) Attach each end of lock rod into slots of drawer as shown.
3. Replace outer head.
LH SIDE
RH SIDE
LOCK ROD
2a
2b
2b
Page 10 of 11939503077 Rev B
Drawer Lock Component Removal��1. Remove lock screw.
2. Remove cam.
3. Remove hex nut.
4. Remove lock barrel assembly.
NOTE: Wood fronts require a lock plate.
12
3a
3b
LOCK BARREL
LOCKSCREW
CAM
4
Page 11 of 11939503077 Rev B
3
1
2
Drawer Re-Assembly��NOTE: Remember to re-install drawers in their original positions.��
1. Verify that drawer rails are pushed back into pedestal.��
2. Pull ball cages on drawer rails to front of drawer rails.��
3. Carefully align drawer portion of rail with ball cage of pedestal portion of rail and gently push drawer back into pedestal.��TIP: Failure to re-assemble drawers correctly may damage rails, rendering them non-functional.